Other Materials Science and Engineering Commons^™

Development Of A Self-Healing And Rejuvenating Mechanisms For Asphalt Mixtures Containing Recycled Asphalt Shingle, Marwa Hassan

Publications

The objective of this study was to test the hypothesis that hollow-fibers encapsulating a rejuvenator product could improve both self-healing, rejuvenation, and mechanical properties of asphalt mixtures. Hollow-fibers containing a rejuvenating product were synthesized via a wet spinning procedure with sodium-alginate polymer as the encapsulating material. An optimization of the production parameters for the synthesis of fibers was performed to develop fibers suitable for high-temperature and shear stress environment typical of asphalt mixture production. A self-healing experiment was conducted to evaluate the healing/rejuvenation capabilities of sodium-alginate fibers in asphalt mixtures with varying types of binders and recycled materials. Based on …

Development Of A Standard Test Method For Characterization Of Asphalt Materials And Aging-Related Degradation Using An Extensional Rheometer, Nazimuddin Wasiuddin

Publications

An extensional deformation test method using a Sentmanat Extensional Rheometer (SER) fixture inside a Dynamic Shear Rheometer (DSR) is developed in this study to investigate the degradation of the polymer due to aging and to investigate the effect of modifier type. A relationship between different percentages of modifier and ductility of the modified binder is also investigated. The sample geometrics used in this study are 1 mm x 0.72 mm and 3 mm x 0.72 mm. A total of one hundred and sixty-two samples were tested. Three modifiers Styrene-Butadiene-Styrene (SBS), Polyphosphoric Acid (PPA) and latex were used. One PG 76-22, …

Bridge Deck Overlays Using Ultra-High Performance Concrete, Craig Newtson, Brad Weldon

Publications

This study investigated the use of a locally produced ultra-high performance concrete (UHPC) as an alternative to typical overlay materials. Several bond strength tests including slant-shear, splitting tension, and direct tension tests were performed to assess the bond strength between UHPC and normal strength concrete (NSC) substrate with varying surface textures. Tests were also conducted to assess the early-age and longer-term shrinkage behavior and coefficient of thermal expansion of the UHPC as well as rapid chloride permeability testing. Good bond between UHPC and NSC substrate was observed even with inadequate surface texture. Combined shrinkage and thermal effects were investigated for …

Experimental Tests And Numerical Simulations For Failure Investigation On Corrugated Boxes Used On Household Appliance Packaging, Diego Fernandes Rodrigues, José Carlos Pereira

Journal of Applied Packaging Research

Packages made of corrugated paper are fundamental to the protection, transportation and handling of the appliance product market. During the storage and sales stages of a product, the package must resist compressive loads in different directions beyond moderate impacts. In this context, the objective of this work is to develop and implement a post-processor that allows the simultaneous analysis of two of the most common failure modes of packages made of corrugated paper: failure due to tensile or compressive stress limit, and failure due to local buckling, when the buckling of the faces of the corrugated paper between two peaks …

Nanoflower-Like Bi2moo6/Ag3po4 In Water Treatment, Xavier Morgan-Lange, Jaeyun Moon, Kaleab Ayalew

McNair Poster Presentations

• Environmental issues continue to intensify causing natural resources such as clean water to become increasingly scarce while demand only continues to grow. • Some of the most effective measures taken appear to be bioremediation tactics and their synthetic counterparts. • A critical area of interest are semi-conducting photocatalytic nanomaterials that take advantage of the photo-electric effect and use the introduction of ultra violet (UV) and visible light to induce oxidation and reduction reaction in p-type semiconductors. This results in the decomposition of certain pollutants and/or deactivates certain microbes in water. • These materials have the potential to operate using …

Thermophotovoltaic Devices: Combustion Chamber Optimization And Modelling To Maximize Fuel Efficiency, Arnold Chris Toppo, Ernesto Marinero, Zhaxylyk Kudyshev

The Summer Undergraduate Research Fellowship (SURF) Symposium

Currently, 110 billion cubic meters of natural gas (primarily methane), a potent greenhouse gas, are flared off for environmental and safety reasons. This process results in enough fuel to provide the combined natural gas consumption of Germany and France. The research team developed a thermophotovoltaic device to convert thermal energy to electricity at a high efficiency using proprietary emitters and combustion system. With the current focus being fuel efficiency and the combustion process, the assembly was simulated using ANSYS Fluent modelling software and the following parameters were optimized: air/fuel ratios, flow rates, and inlet sizes. Simultaneously the heat transfer across …

Computational Catalysis: Creating A User-Friendly Tool For Research And Education, Kevin P. Greenman, Peilin Liao

The Summer Undergraduate Research Fellowship (SURF) Symposium

Catalysis is used in a significant portion of production processes in the industrialized world, including most processing of chemicals and fuels. This makes maximizing the efficiency of catalysts a high priority. However, the immense number of candidates for new catalysts precludes the possibility of testing all of them by experiments. Density functional theory (DFT) has been widely and successfully used to calculate material properties relevant to catalysis and to screen promising candidates for experimental testing, but there currently exists no publicly- available, user-friendly tool for performing these DFT calculations. This work details the development of such a tool for nanoHUB.org …

Application Of Nano-Plasmonics For Sers Bio-Detection And Photocatalysis In The Same Platform, Muhammad R. Shattique

Graduate Theses/Dissertations

Nano-biological systems interfacing nano-structured solid surfaces with biological compounds such as oligonucleotides or proteins are highly regarded as enabling materials for biosensing and biocatalysis applications. In particular, nanostructures of noble metals such as gold or silver, when exposed to light, exhibit a phenomenon known as surface plasmon resonance. When a proper metal nanostructure (plasmonic substrate) is exposed to light, very efficient absorption of incoming photons is possible, resulting in a buildup of localized high-energy regions, or “hot-spots”, where energetic carriers or “hot carriers” can be created. These hot-carriers can be used to catalyze desired chemical transformations in materials located nearby. …

The Effects Of Atmospheric Heat Treatments On Tio2 Nanotube Anodes For Lithium-Ion Batteries, Andreas Savva

Boise State University Theses and Dissertations

The effects of various heat treatments on the physical and electrochemical properties of anatase TiO₂ nanotubes were studied in this work. Well-ordered TiO₂ nanotubes were grown via electrochemical anodization and annealed at 450°C to induce a phase transformation to anatase. The heat treatments were conducted under atmospheres of O₂, Ar, N₂, and water vapor (WV) to create different point defects. The oxygen-deficient atmospheres were used to generate oxygen vacancies in the TiO₂ nanotubes, while the water vapor treatment was used to create Ti vacancies by stabilizing them via the protonation of O sites. …

Investigations On Hydrothermally Synthesized Co3o4/Mnxco3-Xo4 Core-Shell Nanoparticles, Ning Bian

Graduate Theses/Dissertations

Two different morphologies (pseudo-spherical shaped or PS type and hexagonal nanoplate shaped or NP type) and two different concentrations (0.07 M and 0.1 M) of manganese incorporated Co₃O₄@Mn_xCo_3-xO₄ core-shell nanoparticles (CSNs) were investigated, respectively. The motivation of this work is to investigate the magnetic properties of, and specifically the exchange bias, between different shaped CSNs and between different Mn-doped CSNs. A two-step synthesis method was utilized to obtain the CSNs: a soft chemical approach was used to obtain Co₃O₄ nanoparticles and a hydrothermal nano-phase epitaxy was used to …

Molecular Assembly Of Monolayer-Protected Gold Nanoparticles And Their Chemical, Thermal, And Ultrasonic Stabilities, Steven Ray Isaacs

Masters Theses & Specialist Projects

Gold monolayer-protected nanoclusters (MPCs) with average diameters of 1-5 nm protected by alkane- and arenethiolates were synthesized. Mixed-monolayer protected nanoparticles (MMPCs) were prepared by functionalizing hexanethiolate-protected MPCs with either 11-mercaptoundecanoic acid (MUA-MMPC), 11-mercaptoundecanol (MUO-MMPC), or 4-aminothiophenol (ATP-MMPC) using ligand place exchange. Presentation of various chemical reagents such as nucleophile, acid, or base and change in physical environment through ultrasonic and thermal irradiation resulted in changes to particles and their physical properties. Thermogravimetric analysis (TGA) was used to measure maximum temperature of the derivated thermogravimetric peaks (Tmax,DTG) as a means of comparing temperature dependence of mass loss. The absorption spectrum within …

Energy Conversion System For Travelers (Ecost), Thipok Bovornratanaraks

The International Student Science Fair 2018

We have innovated “The Energy Conversion System for Travelers” or the ECoST. With the fact that most travelers have wheeled cabin-bags, whilst walking, the wheels will rotate so why don’t we harvest electricity from this kinetic energy? We thus install our innovation, the ECoST, to the bag to generate electricity from the spinning wheels. The electricity is then kept in the storage unit and ready to charge your empty battery devices in an emergency case via a USB port. To make life easy, our ECoST was designed to replicate the power bank charging method; therefore, we can charge …

Feco2o4 As An Anode Material For Lithium Ion Batteries, Chelsea Wong

The International Student Science Fair 2018

Lithium ion batteries (LIBs) are commonly found in many portable electronic appliances due to their ability to be rechargeable. Currently, commercial anodes in Li-ion batteries (graphite) have a theoretical capacity of around 372 mAh/g, while FeCo2O4 that will be investigated as the anode material has a theoretical capacity of 901.985mAh/g, more than double of the current commercial anode’s capacity. Earlier work done by Sharma et al also showed that FeCo2O4 has a very promising initial capacity of 827mAh/g. As such, the engineering goal is to produce a battery that will have a higher capacity than the current commercial Li-ion batteries …

Feco2o4 As An Anode Material For Lithium Ion Batteries, Chelsea Wong

The International Student Science Fair 2018

Lithium ion batteries (LIBs) are commonly found in many portable electronic appliances due to their ability to be rechargeable. Currently, commercial anodes in Li-ion batteries (graphite) have a theoretical capacity of around 372 mAh/g, while FeCo2O4 that will be investigated as the anode material has a theoretical capacity of 901.985mAh/g, more than double of the current commercial anode’s capacity. Earlier work done by Sharma et al also showed that FeCo2O4 has a very promising initial capacity of 827mAh/g. As such, the engineering goal is to produce a battery that will have a higher capacity than the current commercial Li-ion batteries …

In Situ Sem Solidification Study Of Ga And Egain: A Characterization Technique For Monitoring The Microstructural Evolution Of Liquid Metals, Jeremy Geovann Del Aguila

Materials Engineering

Scanning electron microscopy (SEM) video recording is used to characterize the solidification of small volumes of 99.999% pure gallium (Ga) and eutectic gallium-indium (eGaIn) under a high vacuum environment. Specimen are superheated to 55℃ using a hot plate, cast into spherical droplets, and cooled in situ by means of a Peltier cooling stage. Special attention is given to the preparation of the specimen prior to viewing because of gallium and its alloys’ nature to form an oxide layer when melted and air cooled. The oxide acts as a skin that inhibits the observation of microstructural features during solidification. Heated samples …

Phase Change Materials For Thermal Management Of Kennedy Library Study Rooms, Colin J. Empey

Materials Engineering

The overall purpose of this study was to find a phase change material (PCM) or a combination of PCMs as a thermal management solution for the fifth-floor study rooms in Kennedy Library. First and foremost, the PCM must take in heat to change phase. A PCM would be a better candidate the more heat it needs to change phase. To quantify this, the team utilized a DSC to find how much energy each candidate PCM required to change phase. Coconut oil, palm oil, and white chocolate were found to have the best ability to absorb heat. Secondly, the PCM should …

Solar Cell Potential Induced Degradation Sensor, Luc Alexandre Tousignant

Materials Engineering

It is important to maintain Photovoltaic (PV) cells and protect them from damage mechanisms like Potential Induced Degradation (PID), which can contribute to shorter lifespans and lower efficiencies. Current leakage through cell encapsulation can cause charge migration in PV cells that reduces the maximum quantum efficiency, which is the cause of PID. An experiment was setup to determine the feasibility of a non-silicon sensor able to produce similar leakage behavior to traditional PV cells under recorded humidity conditions. Thin sheet metals were encapsulated in EVA, a common PV encapsulant polymer, and mounted in aluminum framing. Three sensors, along with a …

Composite Suspension For A Mass Market Vehicle, Sarah M. Chapiama, Brian Auyeung, Jose Guerrero, Ethan Lau

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Development Of Test Methods For Measuring Fiber Misalignment And Warping In Honeycomb-Core Composite Panels, Wyatt Taylor, Haripriya Nilakantan

Materials Engineering

Zodiac Aerospace manufactures honeycomb-core composite panels to be used in aircraft cabin interior components. During the manufacturing process, some panels become warped such that they cannot be used for their designated aircraft cabin components. As a result, these panels are scrapped because they cannot be recycled. About 44 to 90% of panels become warped during manufacturing. Warping is caused by many factors, including layer misalignment, processing parameters such as temperature and pressure gradients, and fiber misalignment in the prepregs. Currently, Zodiac does not have any data on the effect of fiber misalignment on panel warpage, so a testing protocol was …

Next Generation Protocol: Innovating A Resilient Future, Andrew Steven Rudnick, Jamie Cannady, Joe Decesaro, Juan A. Ortiz Salazar

Materials Engineering

Conventional practices do not account for product life beyond end-of-sale – these practices are not sustainable. We have developed an end-of-life protocol that includes a metric that we call the Recovery Rating. The objectives of this Next Generation Protocol, beyond supporting the United Nations’ Sustainable Development Goals, are to encourage the production of goods designed for recovery and to promote the collaboration between consumers, the public, and the private sector to recover goods at their end-of-life. The Recovery Rating that we propose evaluates and quantifies recovery potential of products. The Recovery Rating, which is normed against embodied energy from the …

Mechanical Characterization Of Selectively Laser Melted 316l Stainless Steel Body Centered Cubic Unit Cells And Lattice Of Varying Node Radii And Strut Angle, Christopher James Hornbeak

Master's Theses

An experimental study of several variants of radius and strut angle of the body centered cubic unit cell was performed to determine the mechanical properties and failure mechanisms of the mesostructure. Quasi static compression tests were performed on an Instron® universal testing machine with a 50kN load cell at 0.2mm/min. The test samples were built using a SLM Solutions 125 selective laser melting machine with 316L stainless steel. Test specimens were based on 5mm cubic unit cells, with a strut diameter 10% of the unit cell size, with skins on top and bottom to provide a cantilever boundary constraint. Specimens …

Analysis Of The Low-Cycle Fatigue Behavior Of Silicone Rubber For Biomedical Balloons, Chase Cooper

Materials Engineering

The development of a medical drug delivery device that allows for the deployment drugs into the adventitial tissue of blood vessels requires the inflation of a silicone elastomer. The inflated silicone must be able to consistently endure multiple loading cycles without failing so that the device can operate reliably. There are multiple methods of processing the silicone for the device and the goal of this study is to examine the effect of the various processing methods on the characteristics of the silicone. The Dynamic Mechanical Analysis Machine (DMA) is used to model the conditions of the device’s application by performing …

Voltage-Controlled Deposition Of Nanoparticles For Next Generation Electronic Materials, Subhodip Maulik

LSU Doctoral Dissertations

This work presents both a feasibility study and an investigation into the voltage-controlled spray deposition of different nanoparticles, namely, carbon nanotubes (CNTs), as well as molybdenum disulfide (MoS₂) and tungsten disulfide (WS₂) from the transition metal dichalcogenides (TMDCs) family of materials. The study considers five different types of substrates as per their potential application to next-generation device electronics. The substrates selected for this research were: 1) aluminum as a conducting substrate, 2) silicon as a semiconducting substrate, 3) glass, silicon dioxide (SiO₂), and syndiotactic poly methyl methacrylate (syndiotactic PMMA) as insulating substrates.

Since the …

Surface Area And Electrocatalytic Properties Of Feni Nanoparticles For The Oxygen Evolution Reaction (Oer), James Burrow

Chemical Engineering Undergraduate Honors Theses

Iron-nickel bimetallic electrocatalysts have recently emerged as some of the best candidates for the oxygen evolution reaction (OER) in alkaline electrolyte. Understanding the effects of composition and morphology of iron-nickel nanoparticles is crucial for optimization and enhanced electrocatalyst performance. Both physical surface area and electrochemical surface area (ECSA) are functions of morphology. In this study, four different iron-nickel nanoparticle catalysts were synthesized. The catalysts were varied based on morphology (alloy versus core-shell) and composition (low, medium, and high stabilizer concentration). Brunauer-Emmett-Teller (BET) surface area analysis was conducted on three of the synthesized iron-nickel nanoparticles using a physisorption analyzer while electrochemical …

Peridynamic Modeling Of Dynamic Fracture In Bio-Inspired Structures For High Velocity Impacts, Sneha Akula

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Bio-inspired damage resistant models have distinct patterns like brick-mortar, Voronoi, helicoidal etc., which show exceptional damage mitigation against high-velocity impacts. These unique patterns increase damage resistance (in some cases up to 3000 times more than the constituent materials) by effectively dispersing the stress waves produced by the impact. Ability to mimic these structures on a larger scale can be ground-breaking and could be used in numerous applications. Advancements in 3D printing have now made possible fabrication of these patterns with ease and at a low cost. Research on dynamic fracture in bio-inspired structures is very limited but it is …

Influence Of Impact Conditions On Feedstock Deposition Behavior Of Cold-Sprayed Fe-Based Metallic Glass, Constance Ziemian, Wendelin Wright, David E. Cipoletti

Faculty Journal Articles

Cold spray is a promising method by which to deposit dense Fe-based metallic glass coatings on conventional metal substrates. Relatively low process temperatures offer the potential to prevent the crystallization of amorphous feedstock powders while still providing adequate particle softening for bonding and coating formation. In this study, Fe48 Mo14 Cr15 Y2 C15 B6 powder was sprayed onto a mild steel substrate, using a variety of process conditions, to investigate the feasibility of forming well-bonded amorphous Fe-based coatings. Particle splat adhesion was examined relative to impact conditions, and the limiting values of temperature and velocity associated with successful softening and …

Optically Active Dye-Based Systems Templated By Dna Exhibiting Excitonic Delocalization, Brittany Lynn Cannon

Boise State University Theses and Dissertations

The concept of quantum computing was first developed in the early 1980’s. The attraction of quantum computers is their potential capacity to solve extremely complex problems, such as factorization, on a timescale far faster than that of classical computers. However, realization of quantum computation is currently in its infancy, and recent implementations possess serious drawbacks that reduce their appeal. Some challenges of current designs include the necessity to cool the systems using liquid helium to near absolute zero temperatures (15 mK) in order to maintain sufficiently long-lifetimes of the Qbits (i.e., unit of quantum information), difficulty with scaling up the …

Evolution Of Mg Az31 Twin Activation With Strain: A Machine Learning Study, Andrew D. Orme

Undergraduate Honors Theses

Machine learning is being adopted in various areas of materials science to both create predictive models and to uncover correlations which reveal underlying physics. However, these two aims are often at odds with each other since the resultant predictive models generally become so complex that they can essentially be described as a black box, making them difficult to understand. In this study, complex relationships between microstructure and twin formation in AZ31 magnesium are investigated as a function of increasing strain. Supervised machine learning is employed, in the form of J-48 decision trees. In one approach, strain is incorporated as an …

Dynamic Behavior Of Materials, Jeremy Floyd, Andrew Minor

Research Horizons Day Posters

No abstract provided.

Waste Management By Waste: Removal Of Acid Dyes From Wastewaters Of Textile Coloration Using Fish Scales, S M Fijul Kabir

LSU Master's Theses

Removal of hazardous acid dyes by economical process using low-cost bio-sorbents from wool industry wastewaters is of a pressing need, since it causes skin and respiratory diseases and disrupts other environmental components. Fish scales (FS), a by-product of fish industry, a type of solid waste, are usually discarded carelessly resulting in pungent odor and environmental burden. In this research, the FS of black drum (Pogonias cromis) were used for the removal of acid dyes (acid red 1 (AR1), acid blue 45 (AB45) and acid yellow 127 (AY126)) from wool industry wastewaters by absorption process with a view to …