Other Materials Science and Engineering Commons^™

Biobased Acrylate Composites With Enhanced Strength For Additive Manufacturing, Nicole Wagner, Joseph Mcwherter

Engineering Faculty Articles and Research

With the expanding use of polymers in additive manufacturing, sustainable resins for use in vat photopolymerization are required to reduce their environmental impact. One promising approach to achieve this is to incorporate biobased fillers that replace the acrylates in photopolymer resins as ‘green’ alternatives. In this study, photopolymer composites consisting of a methacrylate resin with varying calcium carbonate powder content between 0 and 50 wt.% were investigated. A digital light processing technique was used to fabricate tensile test specimens for mechanical testing. Good printability, dimensional accuracy, and good interlayer adhesion were observed for composite resin formulations that incorporated calcium carbonate …

The Modernization Of Large Power Transformer Tanks, Babajide O. Williams

Electronic Theses and Dissertations

Due to the current demands placed on the power grid in terms of climate change, increasing urbanization, and terrorist attacks, the U.S. government in response to these demands, mandated that all the grid components be modernized in order to increase their reliability. As a critical component of the grid, Large Power Transformers (LPTs) play a key role in ensuring sustainable power generation and distribution. A literature search performed in this work and the analysis of data retrieved from the search showed that the tanks of these LPTs are critical to their durability, longevity, and reliability. Therefore, the reliability of LPTs …

Investigation Of Manufacturing Techniques For Magnetorheological Elastomers To Expand Feasibility In A Diverse Array Of Applications, Austin S. Robbins

College of Graduate Studies: Theses & Dissertations

Magnetorheological elastomers, or MREs, are smart composite materials with controllable physical and mechanical properties when introduced to an external stimulus of a magnetic field. The controllability of these properties is highly tunable by the selection of the elastomeric matrix, concentration of magnetically permeable particles, introduction of additives, and the alignment of the constituents during the curing process. The fabrication of MREs typically calls for a mold that is filled with an MRE mixture to create the final desired geometry after curing. These molds are frequently placed under a magnetic field which orients the micron sized magnetic particles along the magnetic …

Non-Destructive Material Analysis Of Metals And Composites Via Thermography, Jonathan R. Doubt, James L. Chapman

Materials Engineering

The Naval Surface Warfare Center, Port Hueneme Division, is interested in the development of non-destructive damage assessment of shipboard materials via drones at distance. Long Pulsed Thermography (LPT), a method of non-destructive evaluation, was investigated as a possible method for detecting damage in metals (5005h24 Al alloy and 1008 carbon steel) and composites (aramid fiber honeycomb sandwich structure) at distances from 0.5 m to 3.0 m. LPT was conducted using two 1000 W can lights to heat the samples, and a FLIR E8-XT thermal camera. The images were then analyzed using ImageJ software to determine if damage could be detected …

Investigation Of The Effects Of Cladding Layers On Longitudinal And Transverse Mechanical Properties In Composite Laminates, Rachel Potratz, Tiffany Foo, Joseph Kamlet

Materials Engineering

The addition of cladding layers to composite laminates is used in industry to improve bond adhesion and the ease of manufacturing. However, there is no public data on the effects of cladding layers on the mechanical properties of composite components. To directly observe how cladding layers affect mechanical properties, four laminates with zero, one, two, and three cladding layers of twill fabric were added symmetrically to a biased core. The mechanical testing performed was tensile, short beam strength, and compression testing in the longitudinal and transverse directions. The measured strengths were related to the longitudinal properties of the core, and …

The Influence Of Time And Temperature On 7781 Prepreg Outside Storage, Matthew L. Fuentez, Edwin Stuart Ross Viii

Materials Engineering

Investigation into the issue of out of specification flow data revealed that unregulated transportation conditions exposed 7781 prepreg with phenolic resin to temperature fluctuations up to 125°F. The temperature fluctuations have the potential to advance unwanted curing in the prepreg, making it unsuitable for manufacturing. However, this explanation does not account for the prepreg exceeding specifications above the upper limit. Another explanation was investigated that involved exposure to moisture. Moisture could be preventing curing from taking place and thus resulting in higher flow values. Data collection was unable to proceed past the preliminary stages due to the COVID-19 pandemic and …

Bending Response Of Timber Mortise And Tenon Joints Reinforced With Filler-Modules And Frp Gussets, Andrew Robert Pacifico

Graduate Theses, Dissertations, and Problem Reports (ETD)

In 2013, the California Bay Area (CBA) passed a set of ordinances to ensure that their 10,000 plus timber soft-story buildings were prepared for seismic events, through nondestructive evaluation methods. Many property owners are searching for an affordable retrofitting system that will also meet CBA’s new laws focusing on installations by the mandated deadlines in 2020. Over the past three to four decades, Fiber Reinforced Polymer (FRP) composites have found their way into the civil infrastructure sector for rehabilitation. The objective of this study is to evaluate the bending behavior retrofitted mortise and tenon timber joints reinforced with engineered wood …

Preparation And Characterization Of Nanocellulose And Its Application In Composite Materials, Xiuxuan Sun

LSU Doctoral Dissertations

Transparent cellulose films from 2,2,6,6-tetramethylpiperidine-1-oxyl radical oxidized cellulose nanocrystals (TOCNs) and 64 wt% sulfuric acid treated cellulose nanocrystals (SACNs) were prepared from bleached wood pulps. Film morphology, optical, mechanical, thermal, and surface wettability properties were characterized and compared. The results showed that TOCNs and SACNs had different average length, diameter, and aspect ratio.

The effect of cellulose nanofibers (CNFs) on flow, hydration, morphology, and strength of oil well cement (OWC) was investigated using a range of spectroscopic methods coupled with rheological modeling and strength analysis. The Vom-Berg model showed the best fitting result of the rheology data. The addition of …

The Effect Of Biocomposite Material In A Composite Structure Under Compression Loading, Benjamin Andrew Sweeney

Master's Theses

While composite structures exhibit exceptional strength and weight saving possibilities for engineering applications, sometimes their overall cost and/or material performance can limit their usage when compared to conventional structural materials. Meanwhile ‘biocomposites’, composite structures consisting of natural fibers (i.e. bamboo fibers), display higher cost efficiency and unique structural benefits such as ‘sustainability’. This analysis will determine if the integration of these two different types of composites are beneficial to the overall structure. Specifically, the structure will consist of a one internal bamboo veneer biocomposite ply; and two external carbon fiber weave composite plies surrounding the bamboo biocomposite. To acquire results …

An Investigation Into The Properties And Fabrication Methods Of Thermoplastic Composites, Ann E. Livingston-Peters

Master's Theses

As applications for thermoplastic composites increase, the understanding of their properties become more important. Fabrication methods for thermoplastic composites continually improve to match designs specifications. These advanced thermoplastics have begun to show an improvement in mechanical properties over those found in thermoset composites commonly used in industry. Polyaryletherketones (PEK) have high service temperatures, good mechanical properties, and improved processing capabilities compared to thermoplastics used in the past making them important to the aerospace industry. The wide range of types of PEK make them suitable for a variety of applications, but selection of specific chemistries, processing parameters, and composite stack-ups determine …

Wolfpack Gear Inc. Composite Frame Firefighter Backpack, Gabriel Mountjoy, Blair Ridings, Carl Drummond Buchenroth

Mechanical Engineering

No abstract provided.

The Effects Of Cure Schedule On Properties Of Glass-Fiber Reinforced Epoxy Matrix Composites, Trevor J. Lee

Materials Engineering

Two different two-component resin systems were cured, via Differential Scanning Calorimetry, for the times recommended by their respective manufacturers. The resin cure schedules were designed to simulate typical and attainable processing conditions; they were cured at 120°F, 140°F, and 160°F, and in-mold post-cured at 200°F, 230°F, and 260°F. The resulting scans were then compared to a baseline cure for each resin system, consisting of two heating-cooling cycles at a constant rate of temperature change. These baseline cures were then used to determine the percent cure of each sample and the shift in glass transition temperature between the baseline cure and …