Other Materials Science and Engineering Commons^™

Field-Assisted Post-Processing Of Cold-Sprayed Pure Copper, Alan Hensley

Theses and Dissertations--Mechanical and Aerospace Engineering

The properties of materials processed through cold spray, and many other AM processes, are non-uniform and unpredictable. In most cases, post-processing is required to achieve desired properties and better uniformity. In cold spray, the typical method is an annealing heat treatment (AHT), which can improve bond strength, reduce porosity, and restore ductility, among other effects. AHT alone, however, is unable to completely remedy any of the unfavorable properties. In addition, long treatments at high temperatures are often needed for satisfactory results. This increases energy consumption and extends production times for products made by the process. For these reasons, numerous investigations …

Made On Mars: Design And Manufacturing Of Structural Polymer-Regolith Composites, Pailey M. Vitale

Williams Honors College, Honors Research Projects

Human exploration of Mars is constrained by harsh environmental conditions and the prohibitive cost of transporting materials from Earth. Long-term sustainability requires the local production of mechanical and structural components using resources available on Mars, thereby minimizing payload mass. This project investigates polymer–regolith composites derived from atmospheric CO₂ and mineral-rich regolith as a pathway toward in-situ manufacturing. These composites, when compatible with additive manufacturing, could replace imported plastics, enable on-demand fabrication, and support closed-loop recycling systems. The objective is to design and evaluate polymer–regolith composites that maintain mechanical integrity and environmental resistance under Martian conditions, including extreme temperature swings, radiation …

Mechanical Behavior Of Additively Manufactured Ti-6al-4v Eli Parts: Effects Of Laser Parameter Selection, Samuel Lopez

UNF Graduate Theses and Dissertations

Additive manufacturing (AM) of TI-6AL‑4V Extra‑Low Interstitial (ELI) enables complex geometries for fatigue‑critical medical device applications, yet fatigue performance remains sensitive to process‑induced defects. This work investigates the effect of laser process parameter selection on the microstructure, mechanical properties, and fatigue behavior of TI- 6AL‑4V ELI fabricated via laser powder bed fusion (L‑PBF) using a Renishaw RenAM system. The influence of laser parameters was isolated by holding powder chemistry, build orientation, scan strategy, sub‑transus annealing, and post‑processing constant between a non‑optimized baseline and an optimized parameter set selected based on tensile performance.

Optical microscopy showed the optimized condition exhibited improved …

In-Situ Defect Detection In Selective Laser Melting Using Convolutional Neural Networks, Ethan Gaigalas

Master's Theses

This thesis develops and trains a convolutional neural network (CNN) to classify defects in metal parts produced by selective laser melting (SLM) using acoustic emission (AE) data. The model successfully identified porosity and standard build layers with high accuracy but consistently struggled to classify lack of fusion (LOF) defects, regardless of input type, normalization, or class count. These results suggest that while AE signals contain distinguishable features for certain defect types, LOF signals may be too subtle or inconsistent for reliable detection. The study addresses the ongoing challenge of in-situ quality monitoring in metal additive manufacturing, where defects like cracks, …

Thermal Modeling Techniques For Additively Manufactured Porous Metals, Lucas D. Rambo

Master's Theses

Advances in additive manufacturing have enabled the creation of metallic components with tailored porosity, offering design flexibility for thermal, structural, and fluid transport applications. This thesis investigates the effective thermal conductivity (ETC) of porous Inconel 625 (IN625) and Inconel-ceramic composites (IN625-RAM2) fabricated by Laser Powder Bed Fusion (LPBF) using Elementum 3D’s PermiAM technology. Experimental measurements of thermal conductivity using the laser flash method are compared to numerical models built from micro-computed tomography data. Simulations were performed using both finite element (FE) and finite volume (FV) methods to evaluate thermal transport in real microstructures. The study investigates the effects of micro- …

Electro-Mechanical Behavior Of Core-Shell Carbon Grease-Silicone Fibers Fabricated Via Coaxial Direct Ink Writing, Fahrettin Kilic

Graduate Theses, Dissertations, and Problem Reports (ETD)

Highly stretchable strain sensors are essential components in soft electronics, enabling integration of sensing and signal transmission into deformable systems. This thesis explores the fabrication and characterization of coaxial core–shell fibers composed of a conductive carbon grease core and an elastomeric silicone shell. These fibers were produced using coaxial direct ink writing (DIW), a versatile additive manufacturing technique that allows continuous deposition of multi-material filaments. The goal was to achieve mechanically compliant yet electrically stable fibers capable of withstanding large deformations, suitable for applications in wearable electronics and soft robotics.
The printed fibers were systematically examined through mechanical tensile testing, …

Effect Of Build Orientation On Tensile Properties And Fractography Of Additive Manufactured Inconel 718 Alloy, Ajay Kumar Maurya, Amit Kumar, Swarnambuj Suman

ASEAN Journal on Science and Technology for Development

The additive manufacturing (AM) technique “Direct Metal Laser Sintering (DMLS)” is used to create 3D objects directly from 3D design data. A lightweight and complexity-free part without any expensive tooling can be fabricated easily using this method, but it is still challenging to achieve the desired mechanical strength from AM parts, as the mechanical properties of AM-produced parts vary with orientation, scan strategy, and process parameters. Inconel 718 alloy is most commonly utilized in the aerospace and automotive industries, because of its high resistance to corrosion and excellent mechanical qualities. This work presents a study to investigate the orientation-based mechanical …

Optimizing Mn-Al Permanent Magnet Performance Through Control Of The Phase Transformation, Ternary Element Addition, And Advanced Processing, Thomas R. Keller

Dartmouth College Ph.D Dissertations

The growing need for electrical power in machines and vehicles brings with it a growing need for critical materials. The current high-performance permanent magnets (PMs) based on rare-earth (RE) elements Nd and Sm cannot escape the problem of raw material cost, geographic scarcity in the earth’s crust, and lack of circular global supply chains. This poses a problem of industrial ecology: can PMs be made from inexpensive, more abundant materials while still meeting sufficient performance criteria? PMs based on the magnetic τ phase of Mn-Al offer a possible alternative to REPMs. However, years of innovation have not yet achieved real-world …

Optimization Of Porosity In Cold Spray Produced Copper And Zinc Coatings, Cameron Hughes

Graduate Theses & Non-Theses

Since its invention in 1981, the cold spray (CS) additive manufacturing (AM) process has been studied and optimized to produce well-adhered, dense material coatings. CS can operate at a wide range of temperatures if the feed material remains in a solid state. Copper and zinc were studied to characterize and understand the effects of heating element voltage, travel speed, and standoff distance on deposit porosity, grain size, microhardness, and coating thickness. Samples were sprayed on 3.2 mm x 25 mm x 150 mm 6061 aluminum substrates. Sections were taken from the middle of the samples to represent steady-state conditions. Sample …

Investigation Of Manufacturing Techniques For Magnetorheological Elastomers To Expand Feasibility In A Diverse Array Of Applications, Austin S. Robbins

College of Graduate Studies: Theses & Dissertations

Magnetorheological elastomers, or MREs, are smart composite materials with controllable physical and mechanical properties when introduced to an external stimulus of a magnetic field. The controllability of these properties is highly tunable by the selection of the elastomeric matrix, concentration of magnetically permeable particles, introduction of additives, and the alignment of the constituents during the curing process. The fabrication of MREs typically calls for a mold that is filled with an MRE mixture to create the final desired geometry after curing. These molds are frequently placed under a magnetic field which orients the micron sized magnetic particles along the magnetic …

Effects Of Surface Noise On Printing Artifacts: An Artistic Approach To Hiding Print Artifacts, Samuel New

All Theses

This research focuses on improving the quality of Fused Filament Fabrication (FFF) 3D printing by using fractal noise to mask certain print artifacts (e.g. layer lines and stair-stepping). The use of textures is quite common in digital sculpting for aesthetic reasons. This study focuses on finding specific textures that minimize visible 3D print artifacts.

Mechanical Characterization Of Selectively Laser Melted 316l Stainless Steel Body Centered Cubic Unit Cells And Lattice Of Varying Node Radii And Strut Angle, Christopher James Hornbeak

Master's Theses

An experimental study of several variants of radius and strut angle of the body centered cubic unit cell was performed to determine the mechanical properties and failure mechanisms of the mesostructure. Quasi static compression tests were performed on an Instron® universal testing machine with a 50kN load cell at 0.2mm/min. The test samples were built using a SLM Solutions 125 selective laser melting machine with 316L stainless steel. Test specimens were based on 5mm cubic unit cells, with a strut diameter 10% of the unit cell size, with skins on top and bottom to provide a cantilever boundary constraint. Specimens …

Effect Of Composition And Build Direction On Additively Manufactured Hastelloy X Alloys, Justin A. Spitzer, Jeffrey T. Schloetter, Sarah Zerga

Materials Engineering

Microcracking has caused premature failure and reduction in properties in additively manufactured (AM) Hastelloy X. The purpose of this research is to meet or exceed the mechanical properties of wrought Hastelloy X by modifying the composition and build direction of Hastelloy X manufactured using Direct Metal Deposition (DMD). Tensile testing, scanning electron microscopy (SEM), and metallography were performed on the samples. ANOVA was used to analyze the dependence that the properties had on build direction and composition. The nominal composition wrought samples had a yield strength of 310.1 MPa and a 60.79% Elongation. Alloy P60-X18 in a horizontal build had …

Metals Additive Manufacturing Powder Aging Characterization, Thomas Russell Lovejoy, Nicholas Karl Muetterties, David Takeo Otsu

Mechanical Engineering

The metallic additive manufacturing process known as selective laser melting requires highly spherical, normally distributed powder with diameters in the range of 10 to 50 microns. Previous observations have shown a degradation in powder quality over time, resulting in unwanted characteristics in the final printed parts. 21-6-9 stainless steel powder was used to fabricate test parts, with leftover powder recycled back into the machine. Powder samples and test specimens were characterized to observe changes across build cycles. Few changes were observed in the physical and mechanical properties of the specimens, however, there were indications of chemical changes across cycles. Potential …