Other Materials Science and Engineering Commons^™

Wolfpack Gear Inc. Composite Frame Firefighter Backpack, Gabriel Mountjoy, Blair Ridings, Carl Drummond Buchenroth

Mechanical Engineering

No abstract provided.

Magnetic Properties Study Of The Mn-Al System With Additions Of B Or C And Mechanical Milling Techniques, Timothy E. Prost

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Recently a shift in the focus of permanent magnetic research has moved from Rare Earth (RE)-based alloys to those made from more readily available elements. Because of their relatively large magnetocrystalline anisotropy, L1₀ compounds have the potential for use as permanent magnet materials. One particular alloy that is readily available and inexpensive is near equi-atomic manganese and aluminum (Mn₅₀-Al₅₀). First characterized in 1958, it did not receive much attention until more recently when RE supply chain issues made the alloy more attractive for commercial and research applications. The ferromagnetic (FM) τ-phase (L1₀) is …

Atomistic Simulations Of Defect Nucleation And Intralayer Fracture In Molybdenum Disulphide During Nanoindentation, James A. Stewart

Graduate Theses and Dissertations

Molybdenum disulphide (MoS2) is a layered, hexagonal crystal that has a very low coefficient of friction. Due to this low coefficient of friction, MoS2 has become a well-known solid lubricant and liquid lubricant additive. As such, nanoparticles of MoS2 have been proposed as an additive to traditional liquid lubricants to provide frictional properties that are sensitive to different temperature and pressure regimes. However, to properly design these MoS2 nanoparticles to be sensitive to different temperature and pressure regimes, it is necessary to understand the mechanical response of crystalline MoS2 under mechanical loading. Specifically, the fundamental mechanism associated with the nucleation …

An Exploratory Investigation Into How Cold Working Can Affect The Acoustic Performance Of Thin Aluminum Foil In A Ribbon Microphone, Alexander (Alex) Stanley

Materials Engineering

Ribbons of 4 μm thin 99.1% pure aluminum foil were cut and corrugated to replace the stock ribbon in an Apex 205 ribbon microphone. Prior to corrugation, half of the ribbons were sandwiched between two KimWipes and two pieces of cardstock then hammered to impart strain hardening. Each ribbon was placed into the microphone capsule and the frequency response of each ribbon was measured. A 10 second sine sweep from 20-20,000 Hz was played through a KRK Rokit 5 speaker and recorded through a ribbon microphone placed 6 inches away from the speaker cone. The signal generated by the ribbon …

Deposition, Characterization, And Fabrication Of A Zinc Oxide Piezoelectric Thin Film Microspeaker Using Dc Reactive Sputtering, Adam Olzick

Master's Theses

A piezoelectric microspeaker device that could be used in a variety of acoustic applications was designed and fabricated using a thin film ZnO layer that was reactively DC sputtered onto a single crystalline n-type silicon substrate. When tested the microspeaker did not produce sound due to complications in the etching process, the thickness of the diaphragms, and clamping effects. Instead, a characterization approach was taken and the structural, optical, electrical, and piezoelectric properties of the ZnO were investigated. Scanning electron microscopy, x-ray diffraction, and atomic force microscopy were utilized to discover the ZnO’s structural properties. Using the XRD and SEM, …

The Synthesis And Characterization Of Gold And Silver Nanoparticles In Formal And Informal Settings, Mathew Wynn

Materials Engineering

Silver nanoparticles were synthesized through the reduction of AgNO3 using NaBH4. The borohydride anions were adsorbed onto silver nanoparticles. The repelling forces of the borohydride anions prevented the aggregation of particles, but the addition of an electrolyte or agitation induced aggregation. A yellow hue was given off by the silver nanoparticle sol that, using a spectrophotometer, had plasmon resonance at 386 nm. The silver nanoparticles were estimated to be 10 to 20 nm in diameter. Gold nanoparticles were synthesized through the reduction of HAuCl4 using Na3C6H5O7. The gold nanoparticle sol gave off a red hue that had plasmon resonance at …

Blunt Impact Performance Evaluation Of Helmet Lining Systems For Military And Recreational Use, Jaclyn Siniora, Ryan Taylor, Darren Suey

Industrial Technology and Packaging

With the increasing problem in collegiate athletes experiencing injuries to the brain, different helmet liners where put to the test to see which liner provided athletes the greatest protection under specific conditions.

This senior project evaluates five different liners in football helmets. Each of the helmet liners were tested at three different temperatures: hot, cold, and ambient. Each helmet had seven different impact locations which were put to the test. The project was designed to be used to test ACH military combat liners as well. Due to shipping bottle necks the ACH combat liners have been left to future Cal …

Biaxial & Twist Testing Of Composite Carbon-Fiber Sandwich Panels For Automotive Racing Vehicles, Erik Eckberg

Materials Engineering

Composite sandwich panels were constructed with 4-ply plain weave carbon-fiber/epoxy face sheets in the 0^o/45^o/0^o/45^o orientation and 1/8^th inch Nomex honeycomb core. The panels were cut into 5-inch square test plates for mechanical testing. All testing was done on a fixture designed and fabricated by Pratt & Miller Engineering and installed on an Instron testing system at Cal Poly. The twist test was performed by supporting diagonal corners of the plate while simultaneously loading the opposite two corners at a crosshead rate of .06 in/min (ASTM 3044-94R11). Out of 10 panels tested, …

Analyzing The Corrosion Resistance Of Ni-Shield 200 Coatings At Different Temperatures When Exposed To Sulphuric Acid, Alex Hussinger

Materials Engineering

Six steel samples each were twin wire arc sprayed with Hastelloy C-276 or Nickel-Shield 200 coatings approximately 0.020″ thick. These samples were then cut into 3″ by 3″ squares. A 2″ diamond grit hole saw was used to abrade and polish to a smooth surface a ring in the middle in order to get an O-ring mechanical seal. The samples were then weighed and loaded into a jig that started from the bottom up with a stainless steel plate, then the sample, then a Viton O-ring, a ¾″ thick glass plate with a 1 3/4″ hole cut in it, another …

Novel Platform Development Using An Assembly Of Carbon Nanotube, Nanogold And Immobilized Rna Capture Element Towards Rapid, Selective Sensing Of Bacteria, Elizabeth I. Maurer, Kristen K. Comfort, Saber M. Hussain, John J. Schlager, Sharmila M. Mukhopadhyay

Chemical and Materials Engineering Faculty Publications

This study examines the creation of a nano-featured biosensor platform designed for the rapid and selective detection of the bacterium Escherichia coli. The foundation of this sensor is carbon nanotubes decorated with gold nanoparticles that are modified with a specific, surface adherent ribonucleic acid (RNA) sequence element. The multi-step sensor assembly was accomplished by growing carbon nanotubes on a graphite substrate, the direct synthesis of gold nanoparticles on the nanotube surface, and the attachment of thiolated RNA to the bound nanoparticles.

The application of the compounded nanomaterials for sensor development has the distinct advantage of retaining the electrical behavior …

Corrosion Of Stainless Steel 316l And Astm F75 Cobalt Chromium Alloy During Immersion Testing In Silver Salt Solutions, Meagan Higgins

Materials Engineering

This study evaluates the potential effects of silver salts on biocompatible metals used for prostheses during the chemical reduction process to produce a silver antimicrobial layer on the metal’s surface. Samples of two biocompatible metals were obtained: Stainless Steel 316L and ASTM F75 Cobalt Chromium Alloy. Three different silver salts were also acquired: silver nitrate, silver sulfadiazine, and silver chloride. Specimens of each metal were cut to size using a 4-1/2 inch aluminum oxide, 40 grit, cut off wheel for metal, attached to a Dewalt Angle Grinder. The biocompatible metal samples were then subject to either Solution 1, water with …

Fabricating Replacement Glass Prisms For The Piedras Blancas Lighthouse, Daniel Garcken

Materials Engineering

The objective of this project was to design and create a process for manufacturing replacement glass prisms for the Piedras Blancas lighthouse and several other lighthouses nationwide. The prisms were designed to be in multiple metal arrays spread across the floor of the beacon room (the topmost room of the lighthouses). The prisms functioned to transmit extra, radiant light from the beacon light through the floor of the beacon room and disperse it into the maintenance room below. Using computer aided drafting (CAD) software, an original prism was measured and modeled; the corresponding mold was also modeled. G-codes for controlling …

Correlation Between 90o Tensile And 90o Flexural Properties For Thermoplastic Based Carbon-Fiber Composites, Amy Lautenbach

Materials Engineering

Thermoplastic matrix composites containing carbon fibers and 4 different resins (TP 1-TP 4) were tested in tension with the fibers at 90 degree to the longitudinal axis following ASTM D 3039-00. The tensile strengths varied from 5.07-13.87 ksi with TP 1 as the strongest, and TP 4 as the weakest. SEM images were taken of the fracture surface of the samples to explore the fiber-matrix interaction. The SEM images showed significantly more wetting of the fibers in the higher strength materials. The SEM images of the two stronger materials showed resin coating the fibers even after fracture while the two …

Biomedical Properties And Preparation Of Iron Oxide-Dextran Nanostructures By Maple Technique, Carmen Steluta Ciobanu, Simona Liliana Iconaru, Eniko Gyorgy, Mihaela Radu, Marieta Costache, Anca Dinischiotu, Philippe Le Coustumer, Khalid Lafdi, Daniela Predoi

Chemical and Materials Engineering Faculty Publications

Background: In this work the chemical structure of dextran-iron oxide thin films was reported. The films were obtained by MAPLE technique from composite targets containing 10 wt. % dextran with 1 and 5 wt.% iron oxide nanoparticles (IONPs). The IONPs were synthesized by co-precipitation method. A KrF* excimer laser source (λ = 248 nm, τFWHM≅25 ns, ν = 10 Hz) was used for the growth of the hybrid, iron oxide NPs-dextran thin films.

Results: Dextran coated iron oxide nanoparticles thin films were indexed into the spinel cubic lattice with a lattice parameter of 8.36 Å. The particle sized calculated was …

Carbon Nanotubes Grown On Glass Fiber As A Strain Sensor For Real Time Structural Health Monitoring, Matthew Boehle, Qiong Jiang, Lingchuan Li, Alexandre Lagounov, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

In order to more effectively monitor the health of composite structures, a fuzzy fiber sensor has been developed. The fuzzy fiber is a bundle of glass fibers with carbon nanotubes or nanofibers (CNTs or CNFs) grown on the surface. The nanotube coating makes the fiber bundle conductive while the small conductive path increases sensitivity. The fuzzy fiber sensor can replace conventional metal foil strain gauges in composite applications. The electrical response of the sensor is monitored in real time to measure strain, vibration, cracking and delamination. Continuous monitoring provides instant notification of any problems. Implementation of this sensor network in …

Characterization Of Mixing In A T-Style Microfluidic Chip, Brian Eric Harley

Master's Theses

The goal of this study is to characterize the mixing that occurs in a microfluidic chip. To characterize the mixing, the minimum length to complete mixing and evolution of mixing will be investigated. There are two types of mixing that occur within a microfluidic channel, diffusion and advection. In the beginning of the microfluidic chip, diffusion is the dominant form of mixing, and in the later portion of the microfluidic chip advection is the dominant form of mixing. The type of design used for this experiment was a zig zag geometry microfluidic chip with channel dimensions of 60 µm X …

Hemp Lime Bio-Composite As A Building Material In Irish Construction, Patrick Daly, Paolo Ronchetti, Tom Woolley Dr

Articles

This report presents the findings of scoping study into the potential application of hemp lime biocomposite as a construction material in Irish context. The research was carried out under STRIVE funding administered under the Irish Environmental Protection Agency (EPA) examining the state of play of hemp lime in construction toward assessing its potential application in Ireland.

The research involved a range of methods, mainly qualitative, including significant literature review and extensive collation of data on hemp lime performance and testing data, semi structured interviews and field work / review of key case studies in Ireland, UK and Europe.

The study …

Development And Validation Of Probabilistic Fatigue Models Containing Out-Life Suspensions, Noel S. Murray

College of Graduate Studies: Theses & Dissertations

Author's abstract: In the area of reliability engineering it is necessary to be confident that a component or system of components will not fail under use for safety and cost reasons. One major mechanism of failure to a mechanical component is fatigue. This is the repetitious motion of loading and unloading of the material, typically below the ultimate tensile strength of the material, which ultimately leads to a catastrophic failure. To ensure this does not happen, engineers design components based on tests to determine the life of these components. These tests are typically conducted on a bench type tester in …

Limited Thermal Conductance Of Metal-Carbon Interfaces, Jaime J. Gengler, Sergei V. Shenogin, John E. Bultman, Ajit K. Roy, Andrey A. Voevodin, Christopher Muratore

Chemical and Materials Engineering Faculty Publications

The thermal conductance for a series of metal-graphite interfaces has been experimentally measured with time-domain thermoreflectance (TDTR). For metals with Debye temperatures up to ∼400 K, a linear relationship exists with the thermal conductance values. For metals with Debye temperatures in excess of ∼400 K, the measured metal-graphite thermal conductance values remain constant near 60 MW m−2 K−1. Titanium showed slightly higher conductance than aluminum, despite the closeness of atomic mass and Debye temperature for the two metals. Surface analysis was used to identify the presence of titaniumcarbide at the interface in contrast to the aluminum and gold-carbon interfaces (with …

Design Mixers To Minimize Effects Of Erosion And Corrosion Erosion, Julian B. Fasano, Eric E. Janz, Kevin J. Myers

Chemical and Materials Engineering Faculty Publications

A thorough review of the major parameters that affect solid-liquid slurry wear on impellers and techniques for minimizing wear is presented. These major parameters include (i) chemical environment, (ii) hardness of solids, (iii) density of solids, (iv) percent solids, (v) shape of solids, (vi) fluid regime (turbulent, transitional, or laminar), (vii) hardness of the mixer's wetted parts, (viii) hydraulic efficiency of the impeller (kinetic energy dissipation rates near the impeller blades), (ix) impact velocity, and (x) impact frequency. Techniques for minimizing the wear on impellers cover the choice of impeller, size and speed of the impeller, alloy selection, and surface …

Cryogenic Machining And Burnishing Of Az31b Magnesium Alloy For Enhanced Surface Integrity And Functional Performance, Zhengwen Pu

Theses and Dissertations--Mechanical and Aerospace Engineering

Surface integrity of manufactured components has a critical impact on their functional performance. Magnesium alloys are lightweight materials used in the transportation industry and are also emerging as a potential material for biodegradable medical implants. However, the unsatisfactory corrosion performance of Mg alloys limits their application to a great extent. Surface integrity factors, such as grain size, crystallographic orientation and residual stress, have been proved to remarkably influence the functional performance of magnesium alloys, including corrosion resistance, wear resistance and fatigue life.

In this dissertation, the influence of machining conditions, including dry and cryogenic cooling (liquid nitrogen was sprayed to …