Other Materials Science and Engineering Commons^™

Fabrication Of Transparent Conducting Electrodes By Chemical Approaches & Their Application Towards Sensing And Energy Storage, Namuni Sneha

Theses and Dissertations

In the intelligent era, there is a growing demand for developing highly efficient and robust wearable electrodes through simple chemical approaches. We developed highperforming transparent electrodes using interconnected Au nanoparticle networks via a simple liquid-liquid interface approach that offers high conductivity, transparency (>85%), and mechanical durability. Additionally, the prepared electrodes exhibit tunable transmittance and sheet resistance, and the method was also adaptable to various substrates without harsh chemical or thermal treatments.

Furthermore, using Au 1L (1-layer) nanonetwork, a highly transparent breath sensor is fabricated with short response and recovery times (1.1 s and 1.3 s). The Au-1L sensor is …

Shape Memory Behavior In Medium To High Entropy Shape Memory Alloys: Design, Prediction, And Experimental Analysis, Hatim Raji

Theses and Dissertations

This dissertation provides a data-driven system integrating synthetic data generation and machine learning (ML) techniques to create multicomponent SMA compositions with specific transformation temperatures (TTs). Models were trained to represent the nonlinear dependencies influencing martensitic transformation behavior by using elemental, thermodynamic, and process-related aspects. The capacity of the ML models on medium entropy NiTiHfPd and high entropy NiTiHfZrCu systems accuracy was confirmed by experimental validation showing TTs closely matched with model outputs.

Magnetically Impelled Arc Butt Welding And Straight Tube Butt Welding Analysis Of Boiler Grade Tube Joints, Santhosh Kumar S

Theses and Dissertations

Boiler-graded tubes of T11, T12, T91, and T92 materials with a thickness of 4.5 mm thick and 44.5 mm outer diameter were selected for the Straight Tube Butt Welding process using Hot Wire (STBW-HW) and Cold Wire (STBW-CW) conditions. Moreover, the research investigates and compares the welding characteristics of dissimilar T11 and T91 boiler-graded tubes using STBW - HW & Magnetically Impelled Arc Butt (MIAB) welding techniques. Similar and dissimilar welding was performed in STBW – HW & CW conditions.

In dissimilar welding, the tensile strength was higher in the T11-T91 STBWHW joints of 663 MPa than in the T12-T92 …

Fatigue Behaviour Of Al 6063 Alloy In Heat Treated, Deep Cryogenic Treated And Equal Channel Angular Pressing (Ecap) Processed Conditions, Sreearravind M

Theses and Dissertations

This research focuses on improving the Low Cycle Fatigue (LCF) life of Al6063 using three different processing techniques – Heat Treatment (HT), Deep Cryogenic Treatment (DCT), and Equal Channel Angular Pressing (ECAP). Al 6063, widely used in structural applications, has limited fatigue performance, necessitating the exploration of advanced processing techniques to enhance its LCF life.

In HT phase, Al 6063 T5 samples were subjected to solid solution HT followed by air and water quenching. The air-quenched (T6A) and water-quenched (T6W) samples were subjected to precipitation hardening. The Ultimate Tensile Strength (UTS) of the T6A sample increased to 188 MPa from …

Hafnium Oxide-Based Nanoheterostructures For Catalytic Radiosensitization And Enhanced X-Ray Radiotherapy, Marlen Dariela Calix Quezada

Theses and Dissertations

Orthovoltage X-ray beams are attractive for surface and intra-operative radiotherapy. Yet, their clinical utility is constrained by rapid attenuation and the limited dose that can be delivered without harming healthy tissue. High-Z hafnium oxide (HfO₂) nanoparticles can boost local energy deposition through the photoelectric effect, while catalytic surface defects accelerate water radiolysis. Harnessing both mechanisms in a single nano-heterostructure could enable potent radiosensitization at diagnostic-range energies.

This thesis develops and evaluates HfO₂-based nanoheterostructures, both bare and Au-decorated, as catalytic radiosensitizers.

Two types of HfO₂ were evaluated, one was synthesized following a specific route and the …

Development, Synthesis And Characterization Of Advanced Low- Cobalt And High-Nickel Cathode Materials For Lithium-Ion Batteries, Arjun Patel

Theses and Dissertations

This dissertation focuses on the improvement of structural and electrochemical stability of active materials for lithium-ion batteries. It explores the modification strategies to mitigate the issues related to Ni-rich cathode materials, along with the continuous production of cathode precursors using a slug flow reactor to improve the quality of the product.

The First part of the dissertation examines the effect of substitution of cobalt with aluminum and iron on the electrochemical stability of Ni-rich lithium nickel cobalt manganese oxide (NCM) materials. This study investigates how Al and Fe doping work and how they impact the performance and stability of these …

Fabrication And Performance Of Scalable Bio-Engineered Porous Layers For Efficient Co2 Capture, Mary Sharon Rose Bondugula

Theses and Dissertations

This dissertation addresses the critical challenge of mitigating climate change by advancing CO2 capture technologies. As global CO2 emissions continue to rise, effective methods for capturing and separating CO2 from industrial processes are essential to combat climate change. Existing CO2 capture systems, such as Pressure Swing Adsorption (PSA) and Temperature Swing Adsorption (TSA), often rely on packed bed designs that face limitations, including poor heat and mass transfer, slow gas diffusion, and low thermal conductivity, reducing their efficiency. To overcome these challenges, this dissertation explores innovative solutions by developing advanced adsorbent coatings and scalable bed configurations.

This research begins by …

Biofabrication Of Tissue Constructs Using Protein-In-Polysaccharide Bioinks For Muscle Regeneration, Harshavardhan B

Theses and Dissertations

Myocardial infarction (MI) and volumetric muscle loss (VML) are debilitating conditions that severely affect patient quality of life and challenge healthcare systems, particularly in diagnosis and treatment. Conventional therapies often result in long recovery periods with limited functional restoration. Advances in regenerative medicine, especially extrusion-based 3D bioprinting, offer promising potential to improve the regeneration of complex tissues by precisely depositing cells and biomaterials layer-by-layer to create tailored tissue constructs.

A critical challenge in muscle tissue regeneration is developing protein-polysaccharide bioinks that closely mimic the native muscle tissue microenvironment. In this study, two protein-inpolysaccharide bioinks (alginate-fibrinogen and methylcellulose-gelatin-alginate) were developed to …

Synergistic Approaches For Microstructural Refinement, Enhanced Mechanical And Wear Behaviour In Additively Manufactured 17-4 Ph Stainless Steel, Pradeep Kumar S

Theses and Dissertations

The surface and microstructural characteristics of additively manufactured parts play a significant role under mechanical loading. Due to its high strength, tailorable mechanical properties by heat treatment, and ease of printability, the 17-4 precipitation hardened (PH) stainless steel is gaining attention in the additive manufacturing (AM) field.

Selective Laser Melting (SLM), one of the laser-based powder bed fusion (L-PBF) processes, is capable of making fully dense metallic parts with high geometrical fidelity and greater design flexibility at high resolution. The main factors limiting the adoption of SLM are poor surface roughness, anisotropic microstructure, and the formation of micro-pores in the …

Experimental Investigation On Mechanical Properties Of Pla Reinforced By Bamboo Fiber/Montmorillonite Clay Hybrid Composites And Analysis Of Machining Characteristics, Nirmal Kumar K

Theses and Dissertations

The study presents a comprehensive investigation into the development, characterization, and machining analysis of novel bio-based polymer hybrid composites comprising Polylactic acid (PLA), bamboo powders (BP), and montmorillonite clay particles (MMT). Initially, the hybrid composites were fabricated using a solvent-free stir casting process, optimizing the weight percentages of BP and MMT to enhance mechanical and thermal properties.

Mechanical tests, including tensile, flexural, and impact tests, along with thermal analysis using thermogravimetric analysis and differential scanning calorimetry, were conducted to evaluate the performance of the composites. In the subsequent phases, advanced machining techniques were employed to analyze the machining characteristics of …

Mechanical Characterization Of Hemp, Jute, And Flax Based Natural Fibre Composites For Non-Structural Applications In Aircraft And Automobiles, Ravi Kumar B

Theses and Dissertations

Demand for reducing energy consumption and detrimental environmental impacts after the effective lifetime of an engineering material are the major driving factors for the development of natural fibre reinforced composites (NFRCs) in various sectors. Compared to synthetic fibre like carbon-fibres or Kevlar, natural fibres provide several benefits including light weight, inexpensive, recyclability, superior specific strength, biodegradable, non-toxic during handling, and less energy intensive during manufacturing. This doctoral work presents observations from mechanical tests and interpretations on the suitability of natural fibre reinforced composites for less heavily loaded engineering applications areas.

In the first stage, jute, flax, and hemp fibres were …

Applicability Of Using Bio-Receptive Concrete For Building Facades In Egypt, Gina Roupheil

Theses and Dissertations

The significant increase in carbon dioxide emissions caused by the construction industry is detrimental to our planet. This is rapidly increasing with the urbanization of cities that is gradually taking its toll on the available green spaces, which help in balancing such emissions. Recently, researchers have been trying to make use of bio-receptivity to create biomaterial systems that could be spread on building envelopes and support the growth of small plant species and microorganisms to establish on. Out of those materials, comes the concrete as a promising material for bio-colonization.

Within this context, this study aims at investigating the applicability …

A Precision-Controlled Investigation Into The Fundamentals Which Drive The Incredible Superhydrophobic Properties Of Soot, Ashton Bressler

Theses and Dissertations

A PRECISION-CONTROLLED INVESTIGATION INTO THE FUNDAMENTALS WHICH DRIVE THE INCREDIBLE SUPERHYDROPHOBIC PROPERTIES OF SOOT

By Ashton Bressler

A thesis submitted as a partial fulfilment of the Virginia Commonwealth University requirements for a Masters of Science at Virginia Commonwealth University.

Virginia Commonwealth University, 2024.

This thesis investigates a precision controlled superhydrophobic soot surface, composed of semi-rigid linked chains of spheres, with a radii of roughly 14um. These spheres have exceptionally useful hydrophobic properties due to; their large surface area, their large triple phase line length, their low area fraction of solid-liquid interface, their ability to deform, and their strength from both …

Advanced Synthesis And Rational Design Of Support Structures For Nobel Metal Heterogeneous Catalysis: Towards Enhanced Activity And Continuous Processes, Brian R. Clark

Theses and Dissertations

The field of catalysis has a wide-ranging impact. Our group has identified the constant need for improved catalytic activity in high-impact applications such as hydrosilylation and cross-coupling reactions. For these reactions, precious metal catalysts often exhibit markedly better performance than their counterparts, but they can be a significant process cost that decreases overall economic efficiencies. To address this challenge, we explored support structures that can enhance catalytic activity at low metal loadings and improve precious metal recovery through simple filtration. We found that a platinum on graphene nanoplatelet catalyst (PtGNP) synthesized via strong electrostatic adsorption with microwave irradiation (SEA-MW) exhibits …

Fabrication & Characterization Of Hybrid Piezoelectric/Triboelectric Nanocomposite Nanogenerators Via Fusion Deposition Modeling, Khaled El Toukhy

Theses and Dissertations

This thesis aims to discuss the potential of using piezoelectric and triboelectric nanogenerators (PTENGs) for energy harvesting, particularly in the sportswear industry. PTENG's main advantage is that it offers good flexibility making it suitable for high-strain applications. The piezoelectric effect is induced by embedding piezoelectric nanofillers into one of the two triboelectric layers. PTENGs can generate both piezoelectric and triboelectric signals when strained resulting in an enhanced output compared to regular piezoelectric nanogenerators (PENGs) and triboelectric nanogenerators (TENGs). TPU was adopted as the matrix for PTENGs advantageous due to their flexibility, low electrical resistivity, and compatibility with additive manufacturing techniques. …

Accurate Evaluation Of The Direction-Dependent Mechanical Properties Of Ideal Single Crystals: A Comparative Ab Initio Study, Jaylan Ali Elhalawani

Theses and Dissertations

The mechanical properties of a single crystal or a grain in a polycrystalline material are highly dependent on the direction of the applied load. Key properties of interest are the Young’s modulus and the Poisson ratio in the small strain limit, and the ideal tensile strength in the large strain regime. Prior atomistic computations of these properties interchangeably used two approaches. In one approach the stress-strain response is explicitly calculated via a numerical tensile test experiment. In the second approach the second order single crystal elastic constants are computed via small deformations and then used in analytical equations to derive …

Aerosol Synthesis Of Tungsten Bronze Particles For Nir Shielding, Hao Tu

Theses and Dissertations

This dissertation emphasizes the need for efficient energy use in buildings and transportation due to global warming and the energy crisis. It suggests that improving energy efficiency can help reduce energy consumption and emissions and support sustainability. The dissertation introduces various transparent materials that can block near-infrared (NIR) radiation from solar radiation to save energy and money, and it highlights the growing market value of such products. The dissertation compares tungsten bronze with other NIR shielding materials and shows its advantages. The dissertation introduces a cheap and environmentally friendly method for continuously producing tungsten bronze particles via aerosol synthesis. Particle …

A Modular Synthesis Of Processable And Thermally Stable Semi-Fluorinated Aryl Ether Polymers Via Step-Growth Polymerization Of Fluoroalkenes, Ketki Eknath Shelar

Theses and Dissertations

Tailored fluoropolymers remain the leading choice for a wide variety of advanced high-performance applications, including electronic/optical and energy conversion, owing to their unique blend of complementary high-performance properties. Amorphous semi-fluorinated polymers exhibit improved solubility and melt processability when compared to traditional perfluoropolymers. A leading class of semi-fluorinated aryl ether polymers includes perfluorocyclobutyl (PFCB), perfluorocycloalkenyl (PFCA), and fluoroarylene vinylene ether (FAVE) polymers. Monomers containing aromatic trifluorovinyl ethers (TFVE) are used to synthesize PFCB polymers via radical-mediated [2+2] cyclodimerization. On the other hand, FAVE and PFCA polymers are polymerized via base-mediated nucleophilic addition/elimination of bisphenols with TFVE monomers and decafluorocyclohexene respectively. The …

Challenges And Signal Processing Of High Strain Rate Mechanical Testing, Barae Lamdini

Theses and Dissertations

Dynamic testing provides valuable insight into the behavior of materials undergoing fast deformation. During Split-Hopkinson Pressure Bar testing, stress waves are measured using strain gauges as voltage variations that are usually very small. Therefore, an amplifier is required to amplify the data and analyze it. One of the few available amplifiers designed for this purpose is provided by Vishay Micro-Measurements which limits the user’s options when it comes to research or industry. Among the challenges of implementing the Hopkinson technology in the industry are the size and cost of the amplifier. In this work, we propose a novel design of …

Characterization Of Hydrogen Embrittlement Sensitivity In High Hardness Steels, David Ahlen Salley

Theses and Dissertations

High hardness steels can be affected by delayed brittle cracking often attributed to hydrogen embrittlement. Improved resistance to hydrogen embrittlement would be beneficial to many industries including military, automotive, and high-rise construction. While other prevention methods include coating, trapping, and barriers, design efforts in this study were focused on improving intrinsic properties to be more resistant to hydrogen embrittlement. Four alloys targeting 477 – 534 HB were designed and produced in-house and compared against a commercial grade 500 HB alloy. Charpy V-notch (CVN) impact toughness and tensile specimens were made according to ASTM E23 and ASTM E8 to characterize mechanical …

Design And Fabrication Of Nanostructured Electrodes For Complementary Electrochemical And Photoelectrochemical Water Splitting, Kholoud El Sayed Abousalem

Theses and Dissertations

Designing highly active, durable, and nonprecious electrodes for overall water splitting is of urgent scientific importance to realize sustainable hydrogen production. Accordingly, the need to search efficient energy production systems is of crucial necessity. In this thesis, two various systems for sustainable hydrogen production have been reported using electrochemical and photoelectrochemical pathways. In the first part of the thesis, electrochemical water splitting involving both hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) has been established. To this end, an innovative approach is demonstrated to synthesize flower-like 3D homogenous trimetallic Mn, Ni, Co phosphide catalysts directly on nickel foam via …

Rational Design Of Metal-Organic Frameworks (Mofs)-Based Functional Materials Towards Better Air Quality, Zan Zhu

Theses and Dissertations

Air pollution is a major threat to environmental safety and public health. Volatile organic compounds (VOCs), particulate matter (PM), and airborne microorganisms are three typical air pollutants. Conventional strategies to prevent and mitigate air pollution have been employed, which, however, are generally passive. For instance, VOC sensing through solid-state devices is a conventional approach, which, however, is not capable of capturing and removing VOCs. On the other hand, air filters and face masks are useful equipment to protect people from inhaling PM and airborne microorganisms. But most commercial filters can only capture them on the surfaces, which may cause secondary …

Branched Chain Amino Acid Strain State Monitoring With Raman Spectroscopy And Plasmonic Bowtie Nanoantenna Devices For Early Disease Detection, Caroline A. Campbell

Theses and Dissertations

This work centers on the development and the down-selection of nano-manufactured devices to be used in conjunction with Raman spectroscopy for probing a branched chain amino acid. The nano-manufactured devices integrate plasmonic nanoantennas for the purpose of amplifying molecular fingerprints, which are otherwise difficult to detect, through Surface Enhanced Raman Spectroscopy (SERS). Plasmonic nanostructures can be utilized for a variety of biomedical and biochemical applications to detect the characteristic fingerprint provided by Raman Spectroscopy. The nano-manufactured devices create an electric field that amplifies minute perturbations and raises the signal above background noise. This may provide a deeper understanding of signal …

Effects Of Additive Manufacturing Techniques On The Magnetocaloric Properties And Chemical Stability Of Lafexcoysi13-X-Y Alloys, Binyam Wodajo

Theses and Dissertations

Additive manufacturing (AM) is an emerging process to fabricate net shape, intricate, engineering components with minimal material waste; however, traditionally it has been largely applied to structural materials. AM of functional materials, such as magnetic materials, has received much less attention and the field is still in its infancy. To date, AM of magnetocaloric regenerators for magnetic refrigeration (an energy-efficient alternative to the conventional vapor-compression cooling technology), remains a challenge. There are several magnetic refrigerator device designs in existence today that are predicted to be highly energy-efficient, on condition that suitable working materials can be developed. This challenge in manufacturing …

Impact Dynamics Of Surfactant-Laden Droplets On Non-Wettable Coatings, Amir Esmaeili

Theses and Dissertations

Owing to their excellent water repellency, non-wettable (superhydrophobic) coatings have gained tremendous attention in the past couple of decades. Alkyl ketene dimer (AKD), an inexpensive polymer frequently used in paper industry as a sizing agent, has shown potentials to become superhydrophobic. The formation of a porous structure after curing the solidified AKD for an extra-long time (4–6 days) results in superhydrophobicity, i.e., a static contact angle with water of >150° and a roll-off angle of <10°. In this work, a facile and low-cost method was used to turn the surface of AKD superhydrophobic in a very short period of time by briefly treating the coatings, obtained from isothermally heated molten AKD at 40 °C for 3 min, with ethanol. The resulting superhydrophobicity is due to the formation of porous, entangled irregular micro/nano textures that create air cushions on the surface leading to droplet state transition from Wenzel to Cassie. As a proof of concept, the same material was applied to the co-sputtered nickel-tungsten thin films, commonly used in micro/nano-electro-mechanical systems, to improve their hydrophobicity. According to the results, at least 20% increase was observed in the dynamic contact angles of the treated substrates.

In addition, this work presents a detailed high-speed imaging analysis of the influence of the molecular weight, concentration and ionic nature of surfactants on droplet …

Continuous Preparation And Application Of Novel Heterogeneous Catalysis, Michael B. Burkholder

Theses and Dissertations

Transition metal heterogeneous catalysts are widely used across many chemical industries to reduce waste and emissions and reduce production time while increasing rate. The prevalence of these materials results from the complex relationship between metal nanoparticles and supports affecting final catalytic performance. Rational catalyst synthesis describes the ability to precisely engineer structures through controlled preparation. Novel materials and continuous processing represent a promising approach for rational catalyst synthesis.

The application of these catalysts in continuous, multiphase processes, such as cross-coupling reactions, oxidation chemistry, and nitroreduction processes, are paramount to developing new commercial routes for high-value products. Pd/G catalysts synthesized by …

Surface Characterization Of Accident Tolerant Fuel Claddings Candidates After Prolonged Exposure To Steam Oxidation, Connor F. Donlan

Theses and Dissertations

Accident Tolerant Fuel Claddings are designed to improve fuel performance and safety in abnormal reactor conditions. The development of these cladding materials has become a top priority for the nuclear community, with incidents such as the Three Mile Island accident and the Fukashima Dai-chi accident. The development of these claddings has resulted in 2 subsections: coating current claddings or replacing cladding materials with new materials. The claddings studied in this thesis are a Zircaloy-4 cladding coated with chromium through physical vapor deposition, Zircaloy-4, and a FeCrAl alloy, C26M. This thesis assessed the surface chemistry, roughness, and wettability after extended exposure …

Accident Tolerant Fuels Claddings And The Evolution Of Their Surface Characteristics Under Critical Heat Flux, Rajnikant V. Umretiya

Theses and Dissertations

Enhanced Accident Tolerant Fuels (ATFs) systems for light water reactors require higher temperature oxidation resistance in steam environments than the current UO₂ – zirconium fuel system. Investigating the ATF materials’ surface properties is needed as they have evidenced to affect the Critical Heat Flux (CHF), which is an important parameter of the thermal-hydraulic performance required to provide safety margins. In this dissertation, the surface properties of FeCrAl alloys (APMT and C26M), Zircaloy-2, Zircaloy-4, and Cr-coating on Zircaloy-4 substrates produced by Physical Vapor Deposition (PVD) and Cold Spray (CS) were investigated according to their chemistry, topography, and wettability. The static …

Perovskite Thin Films Annealed In Supercritical Fluids For Efficient Solar Cells, Gilbert Annohene

Theses and Dissertations

In the field of photovoltaics, scientists and researchers are working fervently to produce a combination of efficient, stable, low cost and scalable devices. Methylammonium lead trihalide perovskite has attracted intense interest due to its high photovoltaic performance, low cost, and ease of manufacture. Their high absorption coefficient, tunable bandgap, low-temperature processing, and abundant elemental constituent provide innumerable advantages over other thin film absorber materials. Since the perovskite film is the most important in the device, morphology, crystallization, compositional and interface engineering have been explored to boost its performance and stability. High temperatures necessary for crystallization of organic-inorganic hybrid perovskite films …

Biomass-Derived Electrode Materials And Sustainable Processes For Supercapacitors, Katelyn M. Shell

Theses and Dissertations

Biomass is one of the most abundant natural resources and has been used as a source of energy for thousands of years. Biomass as a precursor for energy storage materials is still relatively novel and faces several obstacles before becoming commonly used in today’s electrical devices. Currently, energy storage devices, such as batteries, capacitors, and supercapacitors, utilize petroleum-derived graphitic carbons for anodes, generating a need for more sustainable materials. Biomass, as a carbon-rich source for electrode materials, presents a viable and economically feasible alternative due to the prevalent lignocellulosic compounds: lignin, cellulose, and hemicellulose. Preliminary studies on the solid residues …