Metallurgy Commons^™

An Overview Of Biomass-Derived Graphene Oxide And Its Characteristics For Future Sustainable Applications, Afif Wardana, Ahmad Nabil Shahab, Donanta Dhaneswara, Nofrijon Sofyan

Journal of Materials Exploration and Findings

The production of graphene oxide (GO) from biomass presents considerable promise as a sustainable alternative substitute for traditional semiconductors. Biomass waste, abundant and often underutilized worldwide, is distinguished by its high carbon content and regenerative characteristics, rendering it an optimal resource for sustainable material production. By heating its biopolymers, lignocellulosic biomass can be used as a new material to make graphene, which forms three-dimensional turbostratic crystallites. These crystallites, composed of partially defective aromatic carbon sheets with graphite-like characteristics, make it easier to create GO with specialized functions for cutting-edge applications. Its capability underscores the revolutionary potential of biomass waste in …

Recycling Ndfeb Magnets I: Production Of Ree Fluorides By A Novel Lpc Process, Isaac Joseph Cobbinah

Graduate Theses & Non-Theses

Neodymium-iron-boron (NdFeB) magnets account for over 60% of global magnet sales and are widely used in high-tech, military, and clean-energy applications (Ormerod, 2022). However, they contain critical rare earth elements such as Nd, Pr, and Dy which poses supply chain and geopolitical risks for country like the United States, which rely extensively on foreign sources. Recycling end-of-life NdFeB magnets provides a sustainable solution that diminishes environmental impact, strengthens supply security, and supports stable domestic production of important rare earth elements. A three-stage process has been developed for recycling the REE-content of NdFeB magnets. While the focus is on neodymium (Nd), …

Production Of Rare Earth Elements By Molten-Salt Electrolysis, Mohammed Moro

Graduate Theses & Non-Theses

Rare earth elements (REEs) are indispensable, high-value resources that play a crucial role in renewable energy, defense systems and advanced technological systems. REEs are commonly extracted from natural ores or recycled materials such as permanent magnets using hydrometallurgical or pyrometallurgical techniques. In hydrometallurgy, the REE source is leached with acid, followed by solvent extraction and precipitation steps to obtain rare earth compounds like oxides and fluorides. Pyrometallurgy involves dissolving rare earth compounds in a molten halide bath, followed by high-temperature electrolysis to convert them into metals, which are then recovered at the cathode. This process typically includes melting, refining, and …

Process Intensification For Rare Earth Elements Adsorption By Resonant Vibratory Mixing (Rvm), Mehran Saddat

Graduate Theses & Non-Theses

Rare earth elements (REE) are crucial to the advancement of modern technologies. REE applications include electronics, defense systems, wind turbines, catalysts, magnets, and aircraft. Bastnasite, monazite, and xenotime are the primary resources, while the secondary resources, including coal ash, E-waste, and acid mine drainage, are for REE extraction. The primary processing techniques are chemical leaching, ion exchange, chemical precipitation, pyrometallurgy, solvent exchange, biosorption, and adsorption. Adsorption technique is simple, cost-effective, and environmentally friendly, with higher efficiency but at the cost of a longer mixing time. Therefore, there is a pressing need for an optimized mixing technique to improve the adsorption …

The Comparison Of Dixon–Mood And 1/Nf Methods For Fatigue Limit Estimation Of 17–4 Ph Stainless Steel (H900), Arthur Pallar Pallar

Masters Theses

This study compares two methods for estimating the fatigue limit of 17-4 PH stainless steel (H900): the Dixon–Mood staircase and Kujawski 1/Nf linear method. Tests were conducted on an MTS Acumen 3 kN system under axial tension–tension loading at R = 0.1 and 50 Hz, following the standard practice defined in ASTM E466-15. Flat specimens were fabricated by water-jet cutting and polished. Tensile tests verified mechanical properties consistent with published data for the H900 condition. Fifteen specimens tested by the staircase method yielded a mean fatigue limit of 1138 MPa. The 1/Nf analysis using four specimens produced 1159 MPa, 2 …

L.G. Twidwell: A Summary Of Fifty-Six Years Of Research, Larry G. Twidwell

Metallurgy

No abstract provided.

L.G. Twidwell: A Summary Of Fifty-Six Years Of Research, Larry G. Twidwell

Metallurgical & Materials Engineering

No abstract provided.

Chemistry Of Inclusions By Size In Three Primary Copper Anodes, Charles Campbell, Michael Moats

Materials Science and Engineering Faculty Research & Creative Works

Three copper anodes from different commercial electro refineries were characterized to measure inclusion chemistry, size (diameter), and morphology. An automated scanning electron microscope (SEM) paired with energy-dispersive X-ray spectroscopy (EDS) was used to examine hundreds of inclusions near the mold and set sides of each anode. The investigation revealed that in the two anodes with less impurities (99.65% Cu and 99.75% Cu), many of the inclusions were Cu2O with an average diameter of 2 microns. The greater impurity anode (99.05% Cu, 4076 ppm Pb, 1939 ppm As, 635 ppm Bi) contained significant numbers of complex oxide inclusions, averaging 4.6 microns …

Selective Nickel Leaching And Preparation Of Battery-Grade Nickel Carbonate From Copper-Rich Industrial Intermediate, Janaka Jayamini Wijenayake, Michael S. Moats, Lloyd Masuzyo Mseteka, Lana Alagha

Materials Science and Engineering Faculty Research & Creative Works

The rising demand for electric vehicles (EVs) has driven a significant increase in nickel consumption, a critical element in EV battery production. An industrially viable hydrometallurgical process was developed for the selective recovery of nickel from a copper-rich industrial intermediate, containing approximately 70 wt.% Cu and 6 wt.% Ni, predominantly as sulfides alongside minor impurities. Approximately 90% of nickel was selectively extracted via single-stage atmospheric pressure leaching using HCl and H2O2 at 95 °C for 12 h, with the majority of copper retained in the leach residue, which can be utilized as a valuable feedstock for copper smelters. The selectivity …

Tensile Performance Sensitivity To Variations Of Standard 17-4 Ph Heat Treatments On Lpbf-Produced Material, Ben Brown, Cory Read, Joseph Newkirk, Frank Liou

Materials Science and Engineering Faculty Research & Creative Works

Standard heat treatments for metals of a particular composition are typically designed with the assumption of a conventional starting microstructure, such as that produced by casting or wrought processing. When applied to metals fabricated by Laser Powder Bed Fusion (LPBF) metal additive manufacturing (AM), these heat treatments can produce inconsistent performance due to the unique as-built microstructures. This study investigates how modifications to standard heat treatments for 17-4 PH steel influence the microstructure and mechanical properties of LPBF-fabricated material. Specimens were produced and subjected to varying solutionizing and homogenizing treatments followed by standard aging treatments. Microstructures were characterized using optical …

Hydrogen Embrittlement In Shot-Peened Steel, Jia-Huei Tien, David R. Johnson, David Bahr

15th International Conference on Shot Peening

This work investigates the role of shot peening on hydrogen embrittlement resistance in quenched and tempered 1070 steel. Thermal desorption spectroscopy results revealed that shot-peened specimens contained nearly twice the hydrogen (H) content of unpeened samples when charged under the same electrochemical conditions, suggesting the introduction of additional trapping sites occur during peening. The mechanism underlying this behavior can be associated with increased dislocation density and is more consistent with the HELP mechanism. Residual stress measurements show a significant relaxation of compressive stresses in shot-peened specimen after H charging, indicating H enhanced dislocation rearrangement. Both unpeened and peened specimens exhibited …

Anisotropic Residual Stress Measurements In Additively Manufactured 316 Stainless Steel Parts, Rajeshree Varma, Donovan Stumpf, Paul R. Mort

15th International Conference on Shot Peening

Additive manufacturing (AM) using laser powder bed fusion (L-PBF) is increasingly used to produce complex parts for industries like aerospace and medical devices. The intrinsic characteristics of AM – layer-wise deposition and rapid thermal cycling – generate significant, anisotropic, residual stresses that can compromise part quality and performance. Recent studies highlight how these stresses are strongly influenced by process parameters and build orientation. X-ray diffraction (XRD) techniques, including sin²ψ and advanced two-dimensional approaches, have become the preferred methods for non-destructive, directionally resolved measurement of residual stress in AM metals. This review surveys advancements in XRD residual stress methods with a …

From Strain To Stress: Stress Map Testing Of Almen Strips, Donovan Stumpf, Rajeshree Varma, Paul R. Mort

15th International Conference on Shot Peening

Almen strips have long been used to evaluate shot peening intensity, with arc height serving as a proxy for compressive residual stress. Stress mapping tests (SMT) in this work involve the controlled flattening of an Almen test strip onto a spatial pressure sensor, acting as an inferential measurement for the net bending moment caused by the relaxation of the peened strip. This work explores how stress mapping tests add insight into the stress state of Almen strips, potentially offering a fast and practical alternative to residual stress depth profiling. SMT data analysis provides a framework for relating Almen gauge height …

Fourier Analyses Of Optical Profilometry As An Inferential Measurement For Impact Coverage., Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

A critical consideration in peening process design is achieving sufficient impact coverage. Conventional methods for assessing coverage rely on manual inspection, which is time-consuming and poorly suited for automated control. In this work, we investigate the use of frequency-domain analysis to quantify surface modification in peened samples using optical profilometry (OP) data. Three-dimensional surface maps of Almen strips were acquired using a high-resolution OP system and analyzed via fast Fourier transform (FFT) to compute spatial power spectral densities (PSDs). PSD maps and radially averaged profiles reveal consistent amplification of harmonic components similar to the nominal particle size, with increasing intensity …

Improvement Of The Fatigue Behaviour Of Additive Manufatured Scalmalloy By Using Surface Improvement Processes, Francisco José Boby Alcaide, Irene Eras, José Manuel De Los Santos, Alejandro Munoz Castro, Antonio Perinan Butrón, Jorge Sogorb

15th International Conference on Shot Peening

The use of light metals such as Aluminum alloys has experienced a remarkable increase for the additive manufacturing (AM) industry, especially in aerospace.

AM Scalmalloy®. (an Al-Mg-Sc alloy) shows outstanding behavior with much higher mechanical performance with respect to other alloys for powder bed fusion laser-based (PBF-LB) process like AlSi10Mg or AlSi7Mg. Recent studies have mainly focused on static loading, with minor attention to cyclic loading despite its vital importance in many applications.

In this work, the fatigue performance of PBF-LB Scalmalloy was investigated considering the effects of surface treatments to identify the set of optimal post-processes. Shot peening with …

Influence On Shot Peening And Blast Polishing For Rotating Bending Fatigue Strength Of Vacuum Carburized Steel With Circumferential Notch, Yuji Kobayashi, Hayato Taniguchi, Kiyotaka Masaki

15th International Conference on Shot Peening

In order to improve fuel efficiency in automobiles, weight reduction is necessary as well as improving engine efficiency. For transmission gears, thickness reduction is necessary for weight reduction. When the thickness is reduced, the cross-sectional area becomes smaller, and the load stress increases. Therefore, higher fatigue strength is required. Most gears carry out carburizing. Shot peening is often used to improve the fatigue strength of carburized heat-treated parts. After shot peening, compressive residual stress is introduced, but at the same time, surface roughness is increased. Therefore, the processing conditions of shot peening are very important. Blast polishing is a processing …

Reduced Order Approach For Peening Stress Field Variability, Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

A common goal in shot peening research is to connect operational parameters to resultant residual stress fields, providing a means to control and optimize the effectiveness of surface treatment. In practice, experimental measurements of residual stresses are often averaged values over regions that are large in comparison to an impact dimple. In fact, the stochastic nature of impact locations leads to residual stress fields that are distributed. Finite element peening simulations confirm this observation. The goal of this report is to connect operational parameters to localized fluctuations in residual stress through probabilistic reasoning (Figure 1). In particular, the development of …

The Effect Of Surface Treatment On The Fatigue Strength Of Sus316l Additive Manufactured Products, Hitoshi Nishijima, Yuji Kobayashi, Toshiya Tsuji, Kiyotaka Masaki

15th International Conference on Shot Peening

Rotating bending fatigue tests were conducted to investigate the effect of shot peening and barrel finishing on fatigue properties of SUS316L made by laser PBF which was one of additive manufacturing processes. Surface roughness, residual stress, and fatigue strength were investigated for each specimen. As a result, the fatigue strength of the barrel finished specimens was almost same or better than that of the shot peened specimens. Barrel finished specimens increased 4.1 times higher fatigue strength than as-built specimens. The surface roughness of the specimens after barrel finishing was reduced by up to 96% compared to the as-built specimens. On …

Dynamic Flowsheet Modeling Of Shot Peening Processes, Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

Process flowsheet modeling is used to map and predict performance by integrating sub-models within a system. This paper presents a dynamic flowsheet for shot peening used to track the effects of media characteristics, removal of worn media, and replenishment thereof. Input parameters include media characteristics, media feed rate, velocity (i.e., air pressure), effective impact area (i.e., nozzle setup), and recharge replenishment. The media working mix is described dynamically using tri-modal size and shape characteristics: as-manufactured, conditioned, and worn modes, each having impact-dependent rate coefficients for transition to the next mode, i.e., as-manufactured > conditioned > worn > debris. The flowsheet includes the effect …

Evaluating The Effectiveness Of Localized Masking To Prevent Changes In Residual Stress When Shot Peening, James R. Harrison, James Pineault, Tom Mills

15th International Conference on Shot Peening

When shot peening components, it is common practice to mask certain localized regions where peening roughness is not desirable. For example, surfaces that have been highly machined such as bearing races or areas of interference-fit may require masking to protect them from the cold working effects of shot peening. Oftentimes shot peening the grip sections of fatigue test coupons can prevent cracking and failures due to fretting fatigue in the grip area but could affect the outcome of the test if applied to the gauge section of the coupons. Thus, maintaining an “as machined” surface roughness is the most common …

Improving Fatigue Strength And Life Of Single Crystal Cmsx-4, Jochen Peter Fuhr, Lloyd Hackel, Nicolau I. Morar, Noah Holtham, Keivan Davami, Montu Sharma, Rajkumar Roy

15th International Conference on Shot Peening

The deep penetration of laser peening (LP) and retention of residual stress at high temperature by LP is significant in improving fatigue life and strength of superalloys exposed to high temperature and corrosion. Single crystal CMSX-4, was evaluated for stress relaxation and both fatigue life and fatigue strength of material that was LP-treated compared to non-LP and shot-peened (SP) specimens. LP was done with multiple layers using a 20 J/pulse laser where the laser high energy enabled using a 5 mm spot size on the metal surface. Stress measurements by the slitting technique showed the plastic penetration depth exceeded SP …

First Principles Materials Discovery And Design For Photovoltaic And Solar Thermal Alloys Using High Throughput Methods, Andrew Pike

Dartmouth College Ph.D Dissertations

Materials selection has been a challenge since the dawn of time. With the advent of computational methods and high throughput databases, materials can be discovered and assessed before they are even synthesized. In this thesis I will discuss my work towards designing new materials for clean energy uses, especially alloys which have been underexplored from computational methods. To begin, I present a case study explaining the synthesis of the Yb₁₄ZnSb₁₁ thermoelectric material. Next, I explore the class of AM₂Pn₂ Zintl materials. From the previously identified BaCd₂P₂, it is suspected that …

Recent Progress And Scientific Challenges In Wire-Arc Additive Manufacturing Of Metallic Multi-Material Structures, Sainand M. Jadhav, Sambhaji Kusekar, Akash Belure, Satyavan Digole, Abhijeet Mali, Muralimohan Cheepu, Manoj Mugale, Suhas Alkunte, Duckbong Kim

Faculty Articles

Metallic multi-material structures are heterogeneous structures characterized by changing composition, microstructures, and site-specific characteristics, advantageous for numerous applications where multifunctionality is desired. Metallic multi-material structures are known as bimetallic structures (BSs), which are functionally graded materials (FGMs). In recent years, wire-arc additive manufacturing (WAAM) advanced as a promising additive manufacturing process to realize the fabrication of these structures due to its high deposition rate, cost-effectiveness, and material utilization efficiency. This review presents a comprehensive overview of the recent progress, processing strategies, and scientific challenges in WAAM of multi-material structures. The paper begins with an introduction to multi-material structures, followed by …

A Study Of Wear Measurement And Life Prediction Of Insert Chute Liner On Gold Ore Processing, Ferry Ardika Natanael, Nony Maulidya, Dedi Priadi

Journal of Materials Exploration and Findings

Chutes are critical materials handling assets to transport solid particles from one process step to another in mineral processing, coal mining and cement industries. The material transport, because of material characteristics, cause severe wear on internal lining of chutes or bins’ structure. The wear problem on internal lining of bins or chutes needs to be checked to keep production efficiency. Therefore, not checked wear rate causes liner replacement schedule becomes unpredictable. It leads to production loss and highly cost maintenance in industry. This study shows that condition-based maintenance through regular thickness measurement using Ultrasonic Transducer (UT) to predict life service …

Correlation Between Microstructure And Hardfacing Properties With Welding Current Intensity In Reconditioned Low-Alloy Steel Material Using Submerged Arc Welding (Saw) : A Comprehensive Review, Iman Nugraha Asmara, Winarto Winarto

Journal of Materials Exploration and Findings

This review studying the correlation between microstructural transformations and mechanical properties in reconditioned low-allow steel material, focusing on the impact of Submerged Arc Welding (SAW) parameters, especially current, on microstructure . The study highlights how variation on welding parameters, especially current intensity variation, affecting microstructural transformations, hardness, and wear resistance of hardfaced layers. Key aspects such as dilution effect, phases distribution, and carbide formation are reviewed to understanding their impact on mechanical properties. By reviewing insights from existing literature and experimental findings, this review underscores the role of Submerged Arc Welding in enhancing mechanical properties and microstructural of low-alloy steel …

Wear Of High Entropy Alloys: Understanding Effects Of Cryogenic Temperatures And Surface Nitriding On Wear Behavior, Aubrey Yu Tang

Dartmouth College Ph.D Dissertations

Cryogenic tribological applications have become increasingly important with the development and innovation of advanced equipment in aerospace, polar regions, superconductivity, and more. Traditional lubrication methods are not viable under these harsh environments, so metallic materials must be able to maintain excellent mechanical properties and withstand the constant impact and wear alone. High entropy alloys (HEAs) have emerged as potential candidates for these applications because of their wide variety of excellent room temperature properties and apparent improvement of mechanical properties of some HEAs at extremely low temperatures. Despite their promising nature, very limited work has been done on understanding the wear …

Crevice Corrosion Mechanisms Of Cocrmo Alloys In Orthopedic Implants: Retrieval Analysis, Nano-Tribocorrosion And Cellular Responses, Hwaran Lee

All Dissertations

Mechanically assisted corrosion and non-mechanically (chemically) driven corrosion in modular junctions of orthopedic implants using cobalt-chromium-molybdenum (CoCrMo) alloys remain clinical concerns and may contribute to implant failure. The underlying corrosion mechanisms are not yet fully understood, leaving a critical research gap. We hypothesized that corrosion in modular junctions may be driven by aggressive local environments, including fretting, metal ion release (cobalt ion, Co²⁺), low pH and reactive oxygen species (ROS). This dissertation aims to (1) analyze corrosion modes and potential causes in modular junctions; (2) identify chemically driven corrosion modes on CoCrMo alloys using simulated inflammatory modular taper …

Ferroelectricity And Multiferroicity In Ultrathin Films Of Unconventional Transition Metal Oxide, Xin Li

Department of Physics and Astronomy: Dissertations, Theses, and Student Research

Ferroic orders of transition metal oxides, such as ferroelectricity and ferromagnetism, are determined by the intercoupling between spin, charge, lattice. Consequently, ferroic epitaxial thin films have attracted wide interest due to the profuse novel phenomena and the great application potentials for modern electronics. However, the mainstream of the study for transition metal oxides has focused on perovskite structure, limiting the understanding and discovery of novel phenomena associate with ferroic orders. In this thesis, the epitaxial films of hexagonal rare-earth ferrites (h-RFeO₃) and fluorite-structure hafnia oxide (HfO₂) are studied comprehensively, providing new experimental and theoretic …

Shape Memory Behavior In Medium To High Entropy Shape Memory Alloys: Design, Prediction, And Experimental Analysis, Hatim Raji

Theses and Dissertations

This dissertation provides a data-driven system integrating synthetic data generation and machine learning (ML) techniques to create multicomponent SMA compositions with specific transformation temperatures (TTs). Models were trained to represent the nonlinear dependencies influencing martensitic transformation behavior by using elemental, thermodynamic, and process-related aspects. The capacity of the ML models on medium entropy NiTiHfPd and high entropy NiTiHfZrCu systems accuracy was confirmed by experimental validation showing TTs closely matched with model outputs.

Grain Boundary Migration And Radiation Induced Segregation In Fe-Cr Alloys, Mohit Dhoriya

All Theses

Radiation-induced segregation (RIS) is a significant phenomenon that occurs in alloys subjected to irradiation, particularly in environments such as nuclear reactors. This thesis investigates RIS in ferritic Fe- Cr alloys through the use of Atomic Kinetic Monte Carlo (AKMC) simulations, focusing on the interaction between solute atoms and migrating grain boundaries. The study explores the influence of temperature, solute concentration, and grain boundary velocity on solute drag, a critical process driving RIS. The results show that solute migration is strongly influenced by the presence of vacancies and interstitials generated under irradiation, which are absorbed by grain boundaries and other defect …