Metallurgy Commons^™

Material Extrusion 3d Printing Of Metal Alloy: Material, Methods And Application., Sihan Zhang

Electronic Theses and Dissertations

Material extrusion (MEX) additive manufacturing presents a promising pathway for producing metal components with complex geometries while avoiding the safety hazards associated with loose powder handling in conventional metal additive manufacturing processes. This dissertation investigates the development and optimization of MEX processes for aluminum alloys, addressing critical challenges in feedstock formulation, printing parameter optimization, and post-processing strategies. Three distinct approaches were explored to advance the capabilities of aluminum MEX: filament-based processing of 6061 aluminum, paste-based extrusion of 6061 aluminum, and development of a novel aluminum-magnesium-tin alloy system for space manufacturing applications. The filament-based approach successfully demonstrated the production of 6061 …

Magnetically Impelled Arc Butt Welding And Straight Tube Butt Welding Analysis Of Boiler Grade Tube Joints, Santhosh Kumar S

Theses and Dissertations

Boiler-graded tubes of T11, T12, T91, and T92 materials with a thickness of 4.5 mm thick and 44.5 mm outer diameter were selected for the Straight Tube Butt Welding process using Hot Wire (STBW-HW) and Cold Wire (STBW-CW) conditions. Moreover, the research investigates and compares the welding characteristics of dissimilar T11 and T91 boiler-graded tubes using STBW - HW & Magnetically Impelled Arc Butt (MIAB) welding techniques. Similar and dissimilar welding was performed in STBW – HW & CW conditions.

In dissimilar welding, the tensile strength was higher in the T11-T91 STBWHW joints of 663 MPa than in the T12-T92 …

Measurement And Process Relation For Cast Surface Defects, Nachiket Laxman Shinde

Masters Theses

This thesis presents an in-depth investigation into the classification and prediction of surface defects in aluminum sand castings using a combination of experimental trials and machine learning techniques. Key process variables such head height, pouring temperature, resin %, sand type and process were systematically varied to study their influence on defects like veining, and burn-on. Comparative analysis indicated superior performance of the deep learning model in handling nonlinear interactions between process parameters. The study emphasizes the importance of integrating data-driven models with foundry practices to enhance surface quality, reduce rework, and support intelligent decision-making in casting operations.

Ni-Mn-In Heusler Alloy Ribbon For Magnetocaloric Application, Bao Nguyen

Masters Theses

A traditional cooling system, which applies compression technology within the working fluid, has had a lot of negative impacts on the environment and has low efficiency. They have almost reached the thermodynamic efficiency; there is little room for further improvement. Therefore, solid-state cooling systems, especially those that use the magnetocaloric effect (MCE), have drawnmuch interest as an alternative solution for the vapor-compression system. The Heusler alloy, especially Ni-Mn-In in this research, can be an excellent candidate for this application due to its unique properties, such as the shape memory effect and giant MCE. Their giant MCE results from a first-order …

Exploring Metal Additive Manufacturing In Martian Atmospheric Environments, Zane Mebruer

Mechanical Engineering Undergraduate Honors Theses

On-surface manufacturing is key to the success of a planetary colonization, especially that of Mars. However, traditional subtractive manufacturing processes are equipment, energy, and material intensive, meaning novel additive manufacturing (AM) processes must be pursued for this end. Selective laser melting, one of the most effective and versatile AM methods, would be incredibly beneficial to a Martian mission but requires an artificial argon atmosphere to create effective parts. The purpose of this study was to examine if carbon dioxide, the gas that makes up over 95% of Mars’ surface atmosphere, would be a sufficient substitute for argon in SLM fabrication. …

Developing Reduced Order Models For Gas Bubble Formation In Irradiated Metals Using Integrated Phase Field Modeling And Koopman Operator Theory, John M. Eggemeyer V

All Theses

Irradiation damage in materials is prevalent in nuclear components, posing significant risks in the safety and reliability of nuclear reactors. Phase field models offer a versatile framework for modeling irradiation damage in materials at mesoscales. Such high fidelity method has been used to model the formation of fission gas bubbles superlattice, a microstructure array occurs at certain irradiation conditions (dose, dose-rate, and temperature). To overcome the high computational cost of phase field modeling, Koopman operator theory is applied to create reduced order models, allowing for instantaneous simulations of fission gas bubble behaviors. These low fidelity models are integrated into machine …

Manipulating Martensitic Transformation And Residual Stress Development In Stress Superposed Incremental Forming Of Ss304, Elizabeth M. Mamros, Fabian Maaß, Thomas Gnaupel-Herold, A. Erman Tekkaya, Brad L. Kinsey, Jinjin Ha

Faculty Journal Articles

Stress superposition is one of the strategies used in metal deformation processes to increase the material formability, decrease the required forming forces, and create highly customized components. To investigate the effects of tensile and compressive stresses superposed to the single point incremental forming (SPIF) process, experiments and numerical simulations were conducted for a stainless steel 304 (SS304) truncated square pyramid geometry. Tensile stresses were superposed in-plane on the specimen blank by a custom hydraulic frame, and compressive stresses were incorporated via a polyurethane die. Identified parameters for a martensitic transformation kinetics model for SS304 were used in a two-step finite …

Assessment Of H2s-Induced Cracking Susceptibility In Steam Line Pipes And Weld Zones During Geothermal Well Construction, Riene Kaelamanda Pragitta, Yudha Pratesa

Journal of Materials Exploration and Findings

The susceptibility of steam line pipes, especially in the HAZ (heat-affected zone) and weldment areas, to hydrogen sulfide in the geothermal industry is crucial to understand from the early stages, particularly during construction. The combination of tensile stress from residual stresses after welding and metallurgical phase transformation makes the joint areas vulnerable to sulfide stress cracking. This condition becomes even more extreme when the equipment operates during the well stimulation phase. This research assesses the severity of H₂S-induced cracking using NACE MR0175 and ISO 15156-1 standards, focusing on the effects of pH and partial pressure of H₂S (p_{H₂S …}

Physical Characterization Of Copper Anode Slimes, Carter Glynn, Michael S. Moats

Miners Solving for Tomorrow Research Conference

No abstract provided.

L.G. Twidwell Fifty-Six Years Of Research A Summary, Larry G. Twidwell

Metallurgical & Materials Engineering

Larry G. Twidwell, D.Sc. is Emeritus Professor in the Department of Metallurgical and Materials Engineering at Montana Technological University. He has fifty-six years of experience in teaching and directing research in Metallurgical and Materials Engineering at Montana Tech. Twidwell and his graduate students and coworkers have conducted research emphasizing extractive metallurgy and the application of extractive metallurgical engineering to the treatment of metallurgical wastes, process waters and byproducts. Four books, seventy-seven M.Sc. theses, one-hundred-thirty refereed publications and one hundred-eight national and international presentations have resulted from their research efforts. Twidwell has received several outstanding teacher/researcher awards during his tenure at …

Data-Driven Decision Making For Quality Control In Foundry Applications, Ronit Shetty

Dissertations

In the transformative landscape of Industry 4.0, advanced quality control in manufacturing demands innovative methods for processing and analyzing datasets. This dissertation presents a comprehensive study on leveraging high volume data and machine learning to enhance decision making in the foundry industry. The research explores three crucial challenges in the foundry industry: predicting surface roughness, monitoring refractory coating thicknesses, and comparing feature extraction techniques for surface quality classification. The findings underscore the transformative potential of integrating advanced feature engineering techniques and machine learning into manufacturing quality control.

The first of the three challenges introduces a framework that integrates digital images …

Intelligent Turning Cyber-Physical Systems Modeling Using Sysml, Prithbey Raj Dey, David Lee Enke, Mario F. Buchely

Engineering Management and Systems Engineering Faculty Research & Creative Works

Cyber-Physical Systems (CPS) support industrial automation that incorporates people, hardware, signal, computation, and control using networking to achieve desired results. The complex automated CPS design demands a standard and comprehensive approach to appropriately identify the system requirements, define the architecture, and model the relationships among the software and hardware components. Systems Modeling Language (SysML) provides the capability for a comprehensive modeling to capture the desired design requirements in the systems architecture. SysML enables performance estimation of the model by analyzing constraints while identifying interactions among the components through various behavioral diagrams. In this paper, SysML is applied to the design …

Improvement Of Microcracking And Mechanical Properties Of Tungsten Fabricated Via Laser Powder Bed Fusion Through Alloying With Reactive Secondary Constituents, William S. Mockel

Theses and Dissertations

Tungsten (W), a Group VI transition metal, possesses a number of advantageous properties, most notably its impressive mechanical performance at extreme temperatures. While tungsten's nature render traditional manufacturing methods difficult, additive manufacturing through laser powder bed fusion (LPBF) presents a promising avenue for fabricating tungsten components. However, the material’s high ductile-to-brittle transition temperature combined with the embrittling effect of impurities mean that the residual stresses imparted by LPBF result in microcracking in tungsten, degrading its usefulness. This study sought to improve the characteristics of LPBF-W through the removal of embrittling oxygen content via alloying with low concentrations of reactive elements, …

Fatigue Behaviour Of Al 6063 Alloy In Heat Treated, Deep Cryogenic Treated And Equal Channel Angular Pressing (Ecap) Processed Conditions, Sreearravind M

Theses and Dissertations

This research focuses on improving the Low Cycle Fatigue (LCF) life of Al6063 using three different processing techniques – Heat Treatment (HT), Deep Cryogenic Treatment (DCT), and Equal Channel Angular Pressing (ECAP). Al 6063, widely used in structural applications, has limited fatigue performance, necessitating the exploration of advanced processing techniques to enhance its LCF life.

In HT phase, Al 6063 T5 samples were subjected to solid solution HT followed by air and water quenching. The air-quenched (T6A) and water-quenched (T6W) samples were subjected to precipitation hardening. The Ultimate Tensile Strength (UTS) of the T6A sample increased to 188 MPa from …

Selective Leaching Of Rare Earth Elements From Complex Rare Earth Ore Using Deep Eutectic Solvents, Frank Agyemang, Mehran Saddat, Zainab Nasrullah, Richard Ladouceur

Metallurgical & Materials Engineering

Rare earth elements (REEs) are valuable for various modern technological applications, including metallurgy, machine building, radio electronics, instrument engineering, nuclear engineering, and manufacturing. The extraction and separation of rare earth elements (REEs) from their complex ores is challenging due to their distinct physical and chemical properties, contributing to their market scarcity. At present, REE recovery utilizes traditional pyro- or hydrometallurgical processes. The overall process in the recovery and separation of individual elements from complex REE systems suffers from high energy demands and the use of many hazardous chemicals that negatively impact the environment. With the growing trend toward a circular …

Impurity Behavior In Cast Copper Anodes: Implications For Electrorefining In A Circular Economy, Agustin Morales-Aragon, Daniel Sánchez-Rodas, Guillermo Ríos, Michael S. Moats

Materials Science and Engineering Faculty Research & Creative Works

The behavior of impurities in cast copper was investigated to simulate production with increased utilization of secondary sources within the framework of a circular economy. The incorporation of impurities, particularly Ni, Sn, and Sb, from recycled Cu may significantly impact the electrorefining process. In this study, commercial anodes were doped with Ni, Sn, and Sb concentrations of 2500–6500 g/t, 300–900 g/t, and 450–950 g/t, respectively. Anode concentrations of Pb and Bi were maintained at 1000 g/t and 350 g/t, respectively. As concentrations were examined at two levels, 860 or 1700 g/t, depending on the commercial anode used to create the …

Material Vulnerabilities In Aviation: A Comparative Study Of Hiduminium Rr58 In The Concorde, Siddhant Singh, Kuldeep Agarwal

Automotive and Manufacturing Engineering Technology Department Publications

The catastrophic crash of Air France Flight 4590 in the year 2000 disclosed huge flaws in the material used to manufacture the Concorde fuel tanks, Hiduminium RR58 (Aluminum 2618A). Although this alloy was selected due to its resistance to high-temperature, this research examines its thermal and mechanical vulnerabilities, especially in relation to Aluminum 7075-T3, a large-scale application of which in the Boeing 747 was widespread. By comparing tensile strength, thermal conductivity, fatigue life, and creep life, this research determines how Hiduminium RR58's over-aging susceptibility, thermal cycling degradation, and rupture due to impact were contributory causes to the disaster. The study …

Selective Surface Activation And Flotation Of Pyrite For The Recovery Of Tellurium From Sulfide Tailings, Mulenga Mutema Chibesa

Masters Theses

Copper sulfide tailings from past and present mining operations are important secondary sources of critical elements such as tellurium (Te), a key component in cadmium–telluride photovoltaic solar cells. Characterization of tailing streams from copper porphyry (CP) ore flotation revealed that Te-bearing minerals are predominantly hosted in pyrite, which is usually depressed and discarded. Enhancing pyrite recovery is therefore a critical first step toward concentrating Te minerals for downstream extraction. However, pyrite flotation is often hindered by hydrophilic surface complexes formed during prior processing. This research investigated selective flotation of Te-bearing pyrite from CP tailings using micro flotation and bench-scale flotation, …

Characterization And Leaching Feasibility Studies Of Copper Flue Dust For The Recovery Of Main And Trace Metals, Fardis Nakhaei, Marek Locmelis, Lana Alagha, Michael S. Moats, Carlos Eyzaguirre, Cory Smith

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Although copper smelter dust (CSD) is classified as hazardous waste, it also serves as a valuable secondary resource, offering potential for the recovery of critical elements. In this study, CSD samples were collected from the waste heat boiler (WHB) and electrostatic precipitator (ESP) units connected to the flash smelting furnace at a copper smelter. The representative samples were extensively characterized by particle size, and chemical and mineralogical analyses. Following sample characterization, leaching experiments were performed to evaluate the potential extraction of Cu, Fe, As, Zn, Pb, In, Ga, and Ge from the flue dusts. Distilled water, H2SO4, and HCl were …

Effect Of Alloying Additions On Austenite Refinement In Nickel-Alloyed Ductile Cast Irons, Adnan Adib Aahamed

College of Graduate Studies: Theses & Dissertations

The benefits associated with the application of ductile irons are significantly attributed to the control of microstructures, with refinement of austenitic matrix during solidification playing a significant role. Nickel alloyed ductile irons are attractive due to their potential for high ductility and suitability for potential high-temperature applications with stable austenitic microstructure. Refinement of austenite grain structure is thus important to enhance the mechanical properties of the alloyed ductile iron. This research investigates the impact of in-mold additions of different alloying elements on the austenite morphology and grain refinement of nickel-alloyed ductile iron along with the associated mechanical properties. A hypoeutectic …

Optimizing Material Selection And Operational Conditions For Xhv Systems: Lessons From Aisi 1020 And 316l Comparative Studies, Aiman H. Al-Allaq, Md Abdullah Mamun, Matt Poelker, Abdelmageed Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

In this study, AISI 1020 low-carbon steel was investigated as a cost-effective alternative to SS316L stainless steel for reaching extreme high vacuum (XHV) conditions. After being baked at 400°C, a vacuum chamber made of low-carbon steel material exhibited an outgassing rate approximately 2000 times smaller than a similar chamber made of stainless steel. Its activation energy for hydrogen diffusion (27 kJ/mol) is less than half that of stainless steel (60.3 kJ/mol), indicating more efficient hydrogen removal during bakeout. MolFlow+ simulations supported the experimental data and demonstrated the importance of system geometry optimization and minimizing stainless steel content for achieving optimal …

Understanding Heterogeneous Nucleation In Iron Alloys From First Principles: A Review And Discussion, Semen Naumovich Lekakh

Materials Science and Engineering Faculty Research & Creative Works

Heterogeneous nucleation during solidification plays a key role in structure formation of different types of iron-based alloys, including steels and cast irons. A review summarizes the novel theoretical methods which were used to understand the nature of heterogeneous nucleation in iron-based alloys. An ab initio simulation of atomic adsorption was used to predict the activity of heterogeneous nuclei, and the thermodynamic methods were applied to design conditions for desired precipitate formation in the iron melts. A high-resolution TEM study of individual nucleus and statistics of nuclei family, obtained from an automated SEM/EDX analysis, illustrates a possibility to design processes of …

High-Temperature Performance Of Alloyed Cast Irons And Cr/Ni Austenitic Steels—An Overview And Discussion, Simon N. Lekakh, Mei Li, Larry Godlewski

Materials Science and Engineering Faculty Research & Creative Works

Fe-based cast alloys, including cast irons and steels, have been used in service at a wide range of mechanical and thermal load in oxidizing environment. Special alloying practices can be used to improve high temperature performance of Fe-based cast alloys in an oxidizing atmosphere. At elevated temperatures, alloying elements can produce a protective interface layer which prevents oxidant penetration into the metal matrix. However, a combination of thermo-mechanical loads along with surface oxidation can decrease the materials integrity by destroying the stable protected interface limiting the range of working parameters and lifetime performance of the material. This overview aims to …

Design Of Aluminum-Copper Alloy With Scandium In Solution, Austin M. Depottey

Dissertations, Master's Theses and Master's Reports

The 2xxx series of precipitation-strengthened aluminum-copper alloys are commonly used in high-temperature applications (up to 300°C) where lightweight metals are required. Scandium additions to aluminum-copper alloys have gained recent academic interest due to improved high-temperature mechanical properties, by forming coarsening- resistant Al3Sc dispersoids and stabilization of θ′ precipitates. However, gaps in knowledge about the effects of scandium present a challenge to successful commercialization of aluminum-copper-scandium alloys. This work seeks to explore these knowledge gaps and ultimately design and test a commercially feasible aluminum- copper alloy with scandium. To better understand the processing conditions required to avoid the detrimental W-phase (Al8Cu4Sc), …

Machine Learning Design And Experimental Production Of Recycled Aluminum Alloys With Magnesium And Iron, Skylar Patten

Dissertations, Master's Theses and Master's Reports

Recycling aluminum saves up to 95% of the energy required for primary production but introduces impurities such as iron that limit alloy performance. The Al-Mg-Fe system, though commercially used, remains underexplored. This work applies machine learning with Multi-Objective Bayesian Optimization (MOBO) using Thermo-Calc simulations to design Al-Mg-Fe-Si-Cu-Zn alloys with improved castability and reduced porosity. The optimization targeted freezing range, shrinkage, drag coefficient, and microstructural parameters, identifying compositions with high Mg, Si, and Cu and low Zn as optimal. Predicted alloys were experimentally cast and characterized, with yield strengths exceeding 95 MPa and elongation comparable to commercial 319 aluminum in the …

Atomistic Calculations Characterizing Thermodynamic And Mechanical Properties Of High Entropy Alloys, Sarah O'Brien

Theses and Dissertations--Chemical and Materials Engineering

High entropy alloys (HEAs) are an exciting new class of materials. HEAs combine multiple elements in concentrations ranging from 5% to 35%. The large variation in concentrations increases the alloy’s entropy, stabilizing it. The stabilization is due to both an increased configurational entropy and increases the vibrational entropy when the alloy is at higher temperatures. This was seen for both MoNbTaW and FeNiMoW by combining the atomistic techniques: density functional theory (DFT) and density functional perturbation theory (DFPT). For MoNbTaW, the composition plays a large role in stabilizing the alloy over the configuration of elements. For the three-phase alloy, FeNiMoW, …

Microwave-Assisted Reduction Of Critical Metal Oxides From E-Waste Mixture, Kurundu Shavinka Jayasekera

Graduate Theses, Dissertations, and Problem Reports (ETD)

The efficient recovery of critical metals such as tantalum (Ta), manganese (Mn), gallium (Ga), and indium (In) from electronic waste (e-waste) is essential for resource sustainability and environmental protection. This research uses microwave-assisted treatment to investigate the carbothermal reduction of these four specific metals from their oxides in a simulated e-waste mixture, with carbon black serving as both a microwave coupling and reduction agent. Microwave processing is used specifically because it offers a rapid and energy-efficient alternative to conventional thermal methods, with the benefits of intrinsic heating and selective heating of materials. The first experiments centered on understanding the effects …

Exploration And Synthesis Of Tin Intermetallic Single Crystals, Jared L. Shortt

Graduate Theses/Dissertations

This thesis presents the synthesis and characterization of two tin-based intermetallic compounds: Mn₄.₁₂Sn and Ni₆Sn₈Ge₀.₄₇. Single crystals were grown using a high-temperature self-flux method, allowing for the formation of phase-pure samples suitable for structural and physical property analysis. The crystalline phases were identified and refined using powder and single-crystal X-ray diffraction (XRD), while scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM/EDS) was employed to verify stoichiometry and homogeneity. Magnetization measurements performed using a superconducting quantum interference device (SQUID) magnetometer revealed distinct magnetic behavior in the manganese-rich compound, while the nickel-based compound was explored for potential magnetic features arising from …

Side-By-Side Evaluation Of The Outgassing Rate And Ultimate Pressure Achieved Inside Tubes Made Of Low-Carbon And Stainless Steel, Aiman H. Al-Allaq, Md Abdullah Mamun, Matt Poelker, Abdelmageed Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

The hydrogen outgassing rate of a vacuum chamber made of AISI 1020 low-carbon steel was found to be notably smaller than a similar chamber made of AISI 316L stainless steel following heat treatment at 150 degrees C. When the chambers were baked at 400 degrees C, the outgassing rate of the 1020 low-carbon steel chamber was approximately 2000 times smaller than that of the 316L stainless-steel chamber. After quantifying hydrogen outgassing rates, vacuum chambers made of 1020 low-carbon steel and 316L stainless steel were heated for a prescribed duration and then pumped with an ion pump and nonevaporable getter pump …

Effect Of Bioactive Glass On Pxdda / Pxdda-Co-Pla Nanocomposite For Hard Tissue Reconstruction: Synthesis And Characterization, Ehsan Vafa, Lobat Tayebi, Fatemeh Azizli, Somayeh Parham, Katayoon Rezaeeparto, Sedigheh Azadi, Ali Mohammad Amani, Mohammad Javad Azizli, Hesam Kamyab, Shreeshivadasan Chelliapan, Saravanan Rajendran

Electrical & Computer Engineering Faculty Publications

Newer bone graft materials face various challenges in achieving optimal mechanical strength, bioactivity, and antibacterial action simultaneously, which can result in suboptimal regeneration outcomes and increased infection risks In the present study, we developed a novel nanocomposite of poly (xylitol-co-dodecanedioic acid) (PXDDA) and poly (lactic acid) (PLA) with 1-10 wt% incorporation of bioactive glass (BG), utilizing a a PXDDAco-PLA compatibilizer for maintaining homogeneity. Extensive characterization techniques including, Fourier infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauere Emmette Teller (BET), Proton Nuclear Magnetic Resonance (¹H NMR) and contact angle measurements, revealed that the addition …