Metallurgy Commons^™

Lafe0.925ti0.075o3 Perovskite Coated With Ethyl Cellulose: A High-Stability, Low-Hysteresis Platform For Advanced Humidity Sensing, Akhmad Futukhillah Fataba Alaih, Djoko Triyono, Rifqi Almusawi Rafsanjani

Makara Journal of Science

Humidity sensors are pivotal in numerous sectors, such as environmental monitoring, industrial automation, and health-care. This study presents the fabrication and detailed evaluation of an advanced humidity sensor using ethyl cellulose (EC)-coated LaFe_0.925Ti_0.075O₃ (LFTO) perovskite nanoparticles synthesized via the sol-gel method. The LFTO nanopar-ticles exhibited a mesoporous structure with an enhanced surface area, which significantly improved their moisture adsorption capabilities. The innovative application of EC coating addresses critical substrate adhesion issues, enhancing mechanical stability without compromising sensor sensitivity. Comprehensive performance evaluations revealed minimal hysteresis (

Nanostructured Cathode Catalysts For Aem Electrolysis: From Catalyst Design To Degradation And Hydrogen Dynamics, Yamini Kumaran

Electronic Theses & Dissertations (2024 - present)

Anion exchange membrane water electrolysis (AEMWE) presents a promising pathway toward cost-effective and sustainable hydrogen production by integrating the chemical robustness of alkaline systems with the compact, zero-gap design of proton exchange membrane electrolyzers. However, the widespread implementation of AEMWE is limited by the availability of highly active and durable platinum-group-metal (PGM)-free catalysts and by an incomplete understanding of their degradation behavior under realistic operating conditions.

This dissertation focuses on the development, characterization, and mechanistic investigation of nanostructured MoNi₄–MoO₂-based electrodes for efficient and stable hydrogen generation under alkaline and membrane-integrated environments. MoNi₄–MoO₂ nanorods …

A Study Of Wear Measurement And Life Prediction Of Insert Chute Liner On Gold Ore Processing, Ferry Ardika Natanael, Nony Maulidya, Dedi Priadi

Journal of Materials Exploration and Findings

Chutes are critical materials handling assets to transport solid particles from one process step to another in mineral processing, coal mining and cement industries. The material transport, because of material characteristics, cause severe wear on internal lining of chutes or bins’ structure. The wear problem on internal lining of bins or chutes needs to be checked to keep production efficiency. Therefore, not checked wear rate causes liner replacement schedule becomes unpredictable. It leads to production loss and highly cost maintenance in industry. This study shows that condition-based maintenance through regular thickness measurement using Ultrasonic Transducer (UT) to predict life service …

Ferroelectricity And Multiferroicity In Ultrathin Films Of Unconventional Transition Metal Oxide, Xin Li

Department of Physics and Astronomy: Dissertations, Theses, and Student Research

Ferroic orders of transition metal oxides, such as ferroelectricity and ferromagnetism, are determined by the intercoupling between spin, charge, lattice. Consequently, ferroic epitaxial thin films have attracted wide interest due to the profuse novel phenomena and the great application potentials for modern electronics. However, the mainstream of the study for transition metal oxides has focused on perovskite structure, limiting the understanding and discovery of novel phenomena associate with ferroic orders. In this thesis, the epitaxial films of hexagonal rare-earth ferrites (h-RFeO₃) and fluorite-structure hafnia oxide (HfO₂) are studied comprehensively, providing new experimental and theoretic …

Assessment Of H2s-Induced Cracking Susceptibility In Steam Line Pipes And Weld Zones During Geothermal Well Construction, Riene Kaelamanda Pragitta, Yudha Pratesa

Journal of Materials Exploration and Findings

The susceptibility of steam line pipes, especially in the HAZ (heat-affected zone) and weldment areas, to hydrogen sulfide in the geothermal industry is crucial to understand from the early stages, particularly during construction. The combination of tensile stress from residual stresses after welding and metallurgical phase transformation makes the joint areas vulnerable to sulfide stress cracking. This condition becomes even more extreme when the equipment operates during the well stimulation phase. This research assesses the severity of H₂S-induced cracking using NACE MR0175 and ISO 15156-1 standards, focusing on the effects of pH and partial pressure of H₂S (p_{H₂S …}

Preparation Of Mocvd-Grown Photocathodes Containing A Strained Gaas/Gaasp Superlattice, G. Blume, A. Masters, J. Grames, M. Stutzman, M. Grau, S. Marsillac

Physics Faculty Publications

In this work, we investigate heat cleaning options for high-polarization GaAs/GaAsP strained-superlattice (SSL) photocathodes with a distributed Bragg reflector (DBR) that were grown using metalorganic chemical vapor deposition (MOCVD). This was done using a microMott polarimeter at Jefferson Lab to optimize both quantum efficiency and polarization. The fabrication process for MOCVD-grown photocathodes does not allow for the inclusion of an arsenic cap, contrary to what is done when fabricating photocathodes using molecular-beam epitaxy (MBE). Without proper preparation, the performance of MOCVD-grown photocathodes can be limited due to surface contamination. Here, we varied both duration and temperature of the heat cleaning …

Settingsorder Article Reprints Open Accessarticle A Model To Account For The Effects Of Load Ratio And Hydrogen Pressure On The Fatigue Crack Growth Behavior Of Pressure Vessel Steels, Ashok Saxena, Kip O. Findley

Mechanical Engineering Faculty Publications and Presentations

A phenomenological model for estimating the effects of load ratio R and hydrogen pressure P_H2 on the hydrogen-assisted fatigue crack growth rate (HA-FCGR) behavior in the transient and steady-state regimes of pressure vessel steels is described. The "transient regime" is identified with crack growth within a severely embrittled zone of intense plasticity at the crack tip. The "steady-state" behavior is associated with the crack growing into a region of comparatively lower hydrogen concentration located further away from the crack tip. The model treats the effects of R and P_H2 as being functionally separable. In the transient …

Modeling Study Of Si3N4 Waveguides On A Sapphire Platform For Photonic Integration Applications, Diandian Zhang, Shui-Qing Yu, Gregory J. Salamo, Richard A. Soref, Wei Du

Electrical Engineering and Computer Science Faculty Publications and Presentations

Sapphire has various applications in photonics due to its broadband transparency, high-contrast index, and chemical and physical stability. Photonics integration on the sapphire platform has been proposed, along with potentially high-performance lasers made of group III–V materials. In parallel with developing active devices for photonics integration applications, in this work, silicon nitride optical waveguides on a sapphire substrate were analyzed using the commercial software Comsol Multiphysics in a spectral window of 800~2400 nm, covering the operating wavelengths of III–V lasers, which could be monolithically or hybridly integrated on the same substrate. A high confinement factor of ~90% near the single-mode …

Photodegradation Of Microplastics Through Nanomaterials: Insights Into Photocatalysts Modification And Detailed Mechanisms, Yiting Xiao, Yang Tian, Wenbo Xu, Jun Zhu

Biological and Agricultural Engineering Faculty Publications and Presentations

Microplastics (MPs) pose a profound environmental challenge, impacting ecosystems and human health through mechanisms such as bioaccumulation and ecosystem contamination. While traditional water treatment methods can partially remove microplastics, their limitations highlight the need for innovative green approaches like photodegradation to ensure more effective and sustainable removal. This review explores the potential of nanomaterial-enhanced photocatalysts in addressing this issue. Utilizing their unique properties like large surface area and tunable bandgap, nanomaterials significantly improve degradation efficiency. Different strategies for photocatalyst modification to improve photocatalytic performance are thoroughly summarized, with a particular emphasis on element doping and heterojunction construction. Furthermore, this review …

The Behavior Of ½⟨111⟩ Screw Dislocations In W–Mo Alloys Analyzed Through Atomistic Simulations, Lucas A. Heaton, Kevin Chu, Adib J. Samin

Faculty Publications

Analyzing plastic flow in refractory alloys is relevant to many different commercial and technological applications. In this study, screw dislocation statics and dynamics were studied for various compositions of the body-centered cubic binary alloy tungsten–molybdenum (W–Mo). The core structure did not appear to change for different alloy compositions, consistent with the literature. The pure tungsten and pure molybdenum samples had the lowest plastic flow, while the highest dislocation velocities were observed for equiatomic, W_0.5Mo_0.5 alloys. In general, dislocation velocities were found to largely align with a well-established dislocation mobility phenomenological model supporting two discrete dislocation mobility regimes, …

Mechanisms Of Dendritic Shorting In Lithium Metal Batteries With Li7la3zr2o12 Solid Electrolytes, Lukas Karapin-Springorum

Pomona Senior Theses

Energy storage will play a crucial role in efforts to mitigate the effects of climate change caused by greenhouse gas emissions from human activity. Lithium metal batteries using solid electrolytes like Li₇La₃Zr₂O₁₂ have higher energy density than lithium-ion batteries, which may enable a more rapid and complete electrification of transportation. However, lithium metal batteries suffer from undesirable short-circuiting when metallic lithium deposits connect the two electrodes. It has been debated whether these lithium dendrites generally grow directionally from the anode or are generated by the reduction of lithium ions inside the solid electrolyte, …

Optimizing Mn-Al Permanent Magnet Performance Through Control Of The Phase Transformation, Ternary Element Addition, And Advanced Processing, Thomas R. Keller

Dartmouth College Ph.D Dissertations

The growing need for electrical power in machines and vehicles brings with it a growing need for critical materials. The current high-performance permanent magnets (PMs) based on rare-earth (RE) elements Nd and Sm cannot escape the problem of raw material cost, geographic scarcity in the earth’s crust, and lack of circular global supply chains. This poses a problem of industrial ecology: can PMs be made from inexpensive, more abundant materials while still meeting sufficient performance criteria? PMs based on the magnetic τ phase of Mn-Al offer a possible alternative to REPMs. However, years of innovation have not yet achieved real-world …

Machine Learning Strategies For Potential Development In High-Entropy Driven Nickel-Based Superalloys, Marium Mostafiz Mou

Graduate Theses/Dissertations

In this study, I developed Deep Learning interatomic potentials to model a multi-phase and multi-component system of Ni-based Superalloys. The system has up to three major phase constituents, namely Gamma, Gamma Prime, and Transition-metal rich Carbide. I utilized invariant scalar-based and/or equivariant, tensor-based neural network (NN) approach as implemented in DEEPMD, NEQUIP/ALLEGRO codes, respectively, and Moment Tensor Potential (MTP). For the training and validation sets, I employed the ab-initio molecular dynamics (AIMD) trajectory results and ground state DFT calculations, including the energy, force, and virial database from highly diverse compositions, temperatures, and pressures following a “High Entropy Strategy.” The Deep …

Experimental Evidence That Shear Bands In Metallic Glasses Nucleate Like Cracks, Alan A. Long, Wendelin Wright, Xiaojun Gu, Anna Thackray, Mayisha Nakib, Jonathan T. Uhl, Karin A. Dahmen

Faculty Journal Articles

Highly time-resolved mechanical measurements, modeling, and simulations show that large shear bands in bulk metallic glasses nucleate in a manner similar to cracks. When small slips reach a nucleation size, the dynamics changes and the shear band rapidly grows to span the entire sample. Smaller nucleation sizes imply lower ductility. Ductility can be increased by increasing the nucleation size relative to the maximum (“cutoff”) shear band size at the upper edge of the power law scaling range of their size distribution. This can be achieved in three ways: (1) by increasing the nucleation size beyond this cutoff size of the …

Recovery Of Phosphorus From Florida Phosphatic Waste Clay, Amir Eskanlou

Graduate Theses, Dissertations, and Problem Reports (ETD)

This MS thesis examines the recovery of phosphorus (P) from Florida waste clay (WC). A comprehensive literature review revealed that: (i)-The most important values being lost to WC are P and rare earth elements (REEs). For the recovery of these values from WC, two crucial attempts are the removal of extremely fine-sized clays, followed by the recovery of phosphate content, which can pave the path for the recovery of REEs; (ii)-Any scientific/ technological solution should, at the same time, be economically and environmentally attractive to the industry. As such, moving from mostly chemical separation processes to the primarily physical/ physicochemical …

Thermo-Fluid Characterizations Of The Powder-Bed Fusion Additive Manufacturing Processes Using Laser And Electron Beam, M Shafiqur Rahman

LSU New Orleans Theses and Dissertations

The powder-bed fusion (PBF) process is a subdivision of Additive Manufacturing (AM) technology where a heat source at a controlled speed selectively fuses regions of a powder-bed material to form three-dimensional (3-D) parts. Two of the most effective PBF processes are selective laser melting (SLM) and electron beam additive manufacturing (EBAM), which can fabricate full-density metallic parts in a layer-by-layer fashion. In this study, thermal behavior and melt-pool dynamics in the PBF process are investigated by developing 3-D multiphysics-based thermo-fluid models for both SLM and EBAM, containing Ti-6Al-4V alloy as a powder-bed material. The laser and electron beams are modeled …

Magnetocaloric Effect Near Room Temperature In Quintenary And Sextenary Heusler Alloys, Benjamin D. White, R. I. Barabash, O. M. Barabash, I. Jeon, M. B. Maple

All Faculty Scholarship for the College of the Sciences

An inverse magnetocaloric effect is studied in Ni₂Mn_1+xX_1-x-type Heusler alloys. Principally known for their shape-memory properties, these alloys also exhibit significant entropy and temperature changes (ΔS and ΔT_Ad, respectively) under adiabatic conditions when a modest magnetic field is applied. We investigated the impact on magnetocaloric properties of introducing substantial chemical disorder on the X-site (X = Si, Ga, In), of replacing Ni with nonmagnetic Ag, and of replacing a small amount of Mn with Gd. While a reduction in ΔS is observed in the first two cases, we observe a significant enhancement …

Ignition Of A Plasma Discharge Inside An Electrodeless Chamber: Methods And Characteristics, Mounir Laroussi

Electrical & Computer Engineering Faculty Publications

In this paper the generation and diagnostics of a reduced pressure (300 mTorr to 3 Torr) plasma generated inside an electrodeless containment vessel/chamber are presented. The plasma is ignited by a guided ionization wave emitted by a low temperature pulsed plasma jet. The diagnostics techniques include Intensified Charge Coupled Device (ICCD) imaging, emission spectroscopy, and Langmuir probe. The reduced-pressure discharge parameters measured are the magnitude of the electric field, the plasma electron number density and temperature, and discharge expansion speed.

The Incorporation Of Graphene To Lithium Cobalt Oxide As A Cathode To Improve The Performance Of Lithium Ion Batteries, Kenan Wang

Graduate Theses and Dissertations

One of the objectives of this thesis work was to investigate the cathode performance of lithium cobalt oxide (LiCoO2) incorporated with graphene powder in lithium ion batteries (LIBs). Graphene powder was incorporated into cathode materials to enhance the performance of LIBs. The other objective was to impede the construction of a solid electrolyte interphase (SEI) sheet using graphene sheet coating on its cathode.

The results of this work show that adding graphene powder improved the performance of LiCoO¬2 as a cathode material. With the incorporation of different weight percentages of graphene powder, the LiBs showed distinct changes in their charging …

Nanostructural Origin Of Semiconductivity And Large Magnetoresistance In Epitaxial Nico2O4/Al2O3 Thin Films, Congmian Zhen, Xiaozhe Zhang, Wengang Wei, Wenzhe Guo, Ankit Pant, Xiaoshan Xu, Jian Shen, Li Ma, Denglu Hou

Xiaoshan Xu Papers

Despite low resistivity (~1 mΩ cm), metallic electrical transport has not been commonly observed in inverse spinel NiCo₂O₄, except in certain epitaxial thin films. Previous studies have stressed the effect of valence mixing and the degree of spinel inversion on the electrical conduction of NiCo₂O₄ films. In this work, we studied the effect of nanostructural disorder by comparing the NiCo₂O₄ epitaxial films grown on MgAl₂O₄ (1 1 1) and on Al₂O₃ (0 0 1) substrates. Although the optimal growth conditions are similar for the …

Induced Ferromagnetism In Multilayered Graphene In Proximity With Cofe2o4, Himanshu Verma, Dereje Seifu, Shashi P. Karna, Haiping Hong, Mohindar S. Seehra

Faculty & Staff Scholarship

Composites of anisotropic diamagnetic multilayer Graphene (MLG) and ferrimagnetic CoFe2O4 (CFO) nanoparticles (NPs) were synthesized through a one-step sonication process in the presence of a surfactant. The samples were characterized at ambi- ent using x-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), Raman spectroscopy, magnetic force microscopy (MFM) and magnetometry (vibrating sample magnetometer). An induced ferromagnetism was observed in MLG with saturation magnetization MS = 18 emu/g(MLG). This induced ferromagnetism is attributed to ferrimagnetic CFO uniformly distributed on the surface of diamagnetic MLG. SEM images confirm uniform dense distribu- tion of CFO nanoparticles on MLG. MFM images …

Interplay Of Quantum Size Effect, Anisotropy And Surface Stress Shapes The Instability Of Thin Metal Films, Mikhail Khenner

Mathematics Faculty Publications

Morphological instability of a planar surface ([111], [011], or [001]) of an ultra-thin metal film is studied in a parameter space formed by three major effects (the quantum size effect, the surface energy anisotropy and the surface stress) that influence a film dewetting. The analysis is based on the extended Mullins equation, where the effects are cast as functions of the film thickness. The formulation of the quantum size effect (Z. Zhang et al., PRL 80, 5381 (1998)) includes the oscillation of the surface energy with thickness caused by electrons confinement. By systematically comparing the effects, their contributions into the …

The Magnetic, Electrical And Structural Properties Of Copper-Permalloy Alloys, Makram A. Qader, A. Vishina, Lei Yu, Cougar Garcia, Rakesh K. Singh, Nicholas D. Rizzo, Mengchu Huang, Ralph Chamberlin, Kirill Belashchenko, Mark Van Schilfgaarde, N. Newman

Kirill Belashchenko Publications

Copper-permalloy [Cu_1–x(Ni₈₀Fe₂₀)_x] alloy films were deposited by co-sputtering and their chemical, structural, magnetic, and electrical properties were characterized. These films are found to have favorable weak ferromagnetic properties for low temperature magnetoelectronic applications. Our results show that by varying the composition, the saturation magnetization (M_s) can be tuned from 700 emu/cm³ to 0 and the Curie temperature (T_c), can be adjusted from 900 K to 0 K. The M_s and T_c are found to scale linearly between x = 25% and 100%. Electronic structure calculations …

Fabrication And Study Of The Structure And Magnetism Of Rare-Earth Free Nanoclusters, Bhaskar Das

Department of Physics and Astronomy: Dissertations, Theses, and Student Research

No abstract provided.

Thermoelectric Magnetohydrodynamic Effects In Solidification Processes, Andrew Kao, Koulis Pericleous, Peter Lee, Biao Cai, Jianrong Gao

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Photoluminescence Measurement On Low-Temperature Metal Modulation Epitaxy Grown Gan, Yang Wu

Graduate Theses and Dissertations

A low-temperature photoluminescence (PL) study was conducted on low-temperature metal modulation epitaxy (MME) grown GaN. By comparing the PL signal from high temperature grown GaN buffer layers, and MME grown cap layers on top of the buffer layers, it was found that MME grown GaN cap has a significantly greater defect-related emission. The band edge PL from MME grown GaN found to be 3.51eV at low temperature. The binding energy of the exciton in GaN is determined to be 21meV through temperature dependence analysis. A PL peak at 3.29eV was found in the luminescence of the MME grown cap layer, …

Investigation Of The Resistance To Demagnetization In Bulk Rare-Earth Magnets Comprised Of Crystallographically-Aligned, Single-Domain Crystallites With Modified Intergranular Phase, Jie Li

Dissertations, Master's Theses and Master's Reports

The research presented in this dissertation investigates whether an increased coercivity of Neodymium-Iron-Boron (Nd2Fe14B) based bulk magnets at elevated temperature (160°C), which is now only obtainable by substituting ~7wt% dysprosium (Dy) for a portion of neodymium (Nd), can be achieved through specific microstructural modifications with decreased Dy concentrations. The approach is to reduce the size of individual crystallographically-aligned grains in the magnet so that each grain can only support a single magnetic domain and to simultaneously dilute the Nd-Fe inter-granular phase present in conventional magnets with a non-Fe-containing, Nd-rich phase (Nd-Cu alloy) in an attempt to partially magnetically isolate the …

Practical Aspects Of Modern And Future Permanent Magnets, R.W. Mccallum, L. H. Lewis, Ralph Skomski, M. J. Kramer, I. E. Anderson

Ralph Skomski Publications

The mandate to reduce greenhouse gases will require highly efficient electric machines for both power generation and traction motor applications. Although permanent magnet electric machines utilizing Nd2Fe14B-based magnets provide obvious power-to-weight advantages over induction machines, the limited availability and high price of the rare earth (RE) metals make these machines less favorable. Of particular concern is the cost and supply criticality of Dy, a key RE element that is required to improve the high-temperature performance of Nd-based magnetic alloys for use in generators and traction motors. Alternatives to RE-based alloys do exist, but they currently lack the energy density necessary …

Influence Of Microstructure On The Propagation Of Fatigue Cracks In Inconel 617, Benjiman Michael Albiston

Boise State University Theses and Dissertations

Inconel 617 is a candidate material for use in the intermediate heat exchanger of the Next Generation Nuclear Plant. Because of the high temperatures and the fluctuations in stress and temperature, the fatigue behavior of the material is important to understand. The goal of this study was to determine the influences of the microstructure during fatigue crack propagation. For this investigation, Inconel 617 compact tension samples, fatigue tested by Julian Benz at the Idaho National Laboratory, were obtained. The testing conditions included two environments at 650 °C (lab air and impure-He) and varied testing parameters including: loading waveform (triangular, trapezoidal), …

Dynamical Properties Of Ferroelectric Perovskites (Ba,Sr)Tio3 And Pb(Zr,Ti)O3 Systems From First Principles, Jeevaka Weerasinghe

Graduate Theses and Dissertations

A first-principles-based effective Hamiltonian scheme which incorporates coupling between ferroelectric (FE) and antiferrodistortive (AFD) motions is applied to Pb(Zr,Ti)O₃ alloys. It validates the existence of two modes of E symmetry (rather than the single E(1TO) soft mode) in the 50-75 cm^-1 range for temperatures smaller than 200 K and for compositions falling within the Rhombohedral R3c phase. Coupling between long-range-ordered FE and AFD motions is shown to be the cause of the additional mode and more insight into its nature is provided. This scheme is further used to reveal a field-induced anticrossing involving FE and AFD degrees of …