Metallurgy Commons^™

The Performance Analysis Of A Unicast Network When Two Protocols, Sctp (Stream Control Transmission Protocol) And Tcp (Transmission Control Protocol) Coexist In The Network, Bagio Budiardjo, Michael Thiotrisno

Makara Journal of Technology

This paper elaborates the performance analysis of a unicast network when two protocols, SCTP (Stream Control Transmission Protocol) and TCP (Transmission Control Protocol) coexist in the network. These two protocols are tested using File Transfer Protocol (FTP) and Constant Bit Rate (CBR) based traffic. From the simulations, it could be concluded that SCTP could achieve better throughput compared to TCP in both FTP and CBR based traffic, with sufficiently high fairness index of both intrafairness and interfairness. The increase of simulation time yields to the increase and relatively stable network performance. The increase of the number of sessions of small …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Ii Final Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The second phase has resulted in an experimental setup of a fluid flow experiment with experimentation to be completed in the third year. Some of these results were presented at American Nuclear Society, Student Conference April 2-5, …

Comparison Study Of Cooling Fins And Chills Effectiveness In Aluminum Sand Mold Casting, Vladimir E. Kouznetsov

Graduate Research Papers

Besides proper design of gating and risering systems, there are several methods used to control and modify solidification behavior of cast alloys. Within these methods, the most widely used are local cooling aids employing cooling fins (thin segments attached to problematic areas of casting) or external chills (metal inserts placed into mold walls to accelerate heat withdrawing from potential hot spot). The later helps to promote directional solidification when traditional methods are not possible to use due to limitations related to the casting design. Despite relatively wide application in aluminum foundries, there are no specific recommendations on cooling aids parameters …

Study About High Influence Doping To Base Resistance And Bandgap Narrowing At Si/Si1-Xgex/Si Heterojunction Bipolar Transistor, Achmad Fadhol

Makara Journal of Technology

Study About High Influence Doping to Base Resistance and Bandgap Narrowing at Si/Si1-xGex/Si Heterojunction Bipolar Transistor. Heterojunction is a link formed bedween two semiconductor materials and differend bandgap which has thinness under 50nm and grow the mixture of plate SiGe as bases. The link is an abrupt link or graded one. In this research learnt formulation of doping concentration influence to basis resistance and bandgap narrowing through Si/Si1-xGex/Si Heterojunction Bipolar Transistor with abrupt emitter-basis link, besides taking care to mobility and basis wide to basis resistance, it is also influence of mole fraction to bandgap power. From the result shows …

Photocatalytic Treatment Of Heavy Metal Waste Cr(Vi) Withtio2 Photocatalyst, Slamet Slamet, Riyadi Syakur, Wahyu Danumulyo

Makara Journal of Technology

Photocatalytic Treatment of Heavy Metal Waste Cr(VI) with TiO2 Photocatalyst. The photocatalytic reduction of hexavalent chromium/Cr(VI) using TiO2 and copper-doped TiO2 as photocatalysts have been studied in stirred tank and circulating photoreactors. All photocatalysts were characterized with FTIR (Fourier Transform Infra Red), BET (Brunauer-Emmett-Teller), XRD (X-Ray Diffraction) and SEM (Scanning Electron Microscope). TiO2 Merck and Degussa P-25 are the commercial photocatalysts used to compare the photocatalytic activity of all the prepared catalysts. Blank test experiments as well as the effect of dopants, EDTA (ethylenediaminetetraacetic acid) and activated carbon addition were studied. Cr(VI) reduction on various pH and initial Cr(VI) concentration …

Development And Analysis Of Geographic Information System For Electricity Network (Case Study: Surabaya Industrial Estate Rungkut In Surabaya)., Lilik Jamilatul Awalin, Bangun Muljo Sukojo

Makara Journal of Technology

Development and Analysis of Geographic Information System for Electricity Network (Case Study: Surabaya Industrial Estate Rungkut in Surabaya). Geographic Information System (GIS) is a system of data which has spatial base. This may be cause has ability to process and analysis data quickly. The ability of GIS will be able to process the alternative in decision making. The need of electric power grows until recent time along with the existence of industrial sector expansion and land use expansion claim better service, large and balance stock of electric power. GIS is a solution for planning and managing data base system, for …

Application Of Remote Sensing And Geographic Information System Methods For Land Using Difference, Bangun Muljo Sukojo, Diah Susilowati

Makara Journal of Technology

Application of Remote Sensing and Geographic Information System Methods for Land Using Difference. Land using difference analysis has been done using remote sensing and Geographic Information System (GIS) methods. Identification of land using difference was conducted using map overlaying process of 1990s (digitized scalling 1:50.000) and 1997s land using map (interpreted from Landsat TM (Thematic Mapper) Image 1997) with UTM (Universal Transverse Mercator) coordinate. Image enhancement was done through histogram equalization with supervised classification devided into 7 classes: rice field, settlement, dry field, industry, pond, sport field and bush. Land using difference and river pollution BOD (Biological Oxygen Demand), COD …

Phase Composition Analysis Using Rietveld Methode And It's Influence To The Hardness Of Ti-Si-N Nanocomposites, Keba Moto, Lia Setiarini, Zufar Abubakar

Makara Journal of Technology

Phase composition analysis using rietveld methode and it’s influence to the hardness of Ti-Si-N nanocomposites. XRD data of nanocomposites Ti-Si-N have been analysed using GSAS based on Rietveld Method in order to identify phases and their composition as well as its influence on the hardness of these nanocomposites. Several new phases have been found in the sample beside the nc-TiN/a-Si3N4& a-/nc-TiSi2 that have been known widely. From the obtained crystalline phase, after the calculation of amorf Si3N4 and TiSi2 phase fraction, it is found that the optimum hardness can be reached when the fraction of a-Si3N4 phase around 8 wt.%

Influence Of Strain Rate And Temperature Of Hot Tension Testing On Mechanical Properties Of Medium Carbon Steel S48c, Dedi Priadi, Iwan Setyadi, Eddy S. Siradj

Makara Journal of Technology

Influence of Strain Rate and Temperature of Hot Tension Testing on Mechanical Properties of Medium Carbon Steel S48C. The characterization of S48C by hot tension testing was done to understanding the influence of temperature and strain rate for S48C flow stress, that close relationship with its forge ability. The hot tension testing was performed on temperatures and strain rates variation (T 850, 900, 950 0C and έ 0,01;1 s-1). The result of hot tension testing showed that increasing temperature decreases ultimate tensile strength (UTS) and flow stress of S48C. The higher decreasing of UTS is on 950 0C about 85% …

Modeling, Fabrication, And Optimization Of Niobium Cavities Phase Ii: Third Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. The second phase has resulted in an experimental setup of a fluid flow experiment with experimentation to be completed in the third year. Other experimental activities include the evaluation of a vacuum system and various vacuum equipment …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada, Las Vegas (UNLV) and the Idaho State University (ISU) is to evaluate the feasibility of determining residual stresses of welded, bent (three-point-bend), and cold-worked engineering materials using a new nondestructive technique based on positron annihilation spectroscopy. The proposed technique is to use x-rays from a small MeV electron Linac to generate positrons inside the sample via pair production. This method can be used for materials characterization and investigation of defects in thick samples that could not be accomplished by conventional positron technique or other nondestructive methods. The data …

Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Darrell Pepper, Randy Clarksean

Fuels Campaign (TRP)

UNLV has developed and will continue to develop process models for the analysis of melt casting processes. This work will continue to be performed under the guidance of Argonne National Laboratory (ANL) engineers to insure that their knowledge and experience benefits the project. The research to be conducted during year three will center on performing detailed analyses on a conceptual design of an inductively heated skull-crucible casting furnace. Processing conditions will be analyzed, basic models utilized, and detailed heat and mass transfer models will be developed to analyze the most promising processes. The goal of this third year is to …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Final Phase, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for superconducting cavities. The need for very clean surfaces lead to the use of a buffered chemical polishing produce for surface cleaning to get good performance of the cavities. This is the third and final phase of the study.

The first phase has resulted in improving the basic understanding of multipacting and the process of chemical etching. The second phase has resulted in an experimental setup …

Modeling, Fabrication, And Optimization Of Niobium Cavities, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

One of the key technologies for the deployment of accelerator driven transmutation systems is the accelerator itself. To increase the efficiency of the high-power accelerators needed to support the transmutation mission, the national and international accelerator teams have proposed using elliptical superconducting niobium cavities. This project is tasked with examining the impacts of the design and fabrication technologies for these elliptical niobium cavities on their performance. Niobium was selected primarily due to its behavior at low temperatures.

One of the major sources of energy loss from a superconducting accelerator cavity is a process known as multiple impacting (or “multipacting”) of …

Effects Of Environmental Variables And Stress Concentration On Target Materials, Sudheer Sama

Transmutation Sciences Materials (TRP)

This paper presents a brief summary on stress corrosion cracking (SCC) behavior of alloy HT 9. The susceptibility of this alloy to SCC was evaluated by using constant load and slow strain rate test techniques in neutral and acidic solutions at ambient temperature and 90°C. A proof ring was used to apply tensile load to the smooth specimen for 30 days in constant load testing. In slow strain rate testing, the specimen was continuously strained in tension at a rate of 3.3 × 10^-6 sec^-1 until fracture.

Effects Of Environmental Variables And Stress Concentration On Cracking Of Spallation Target Materials, Ajit K. Roy, Ramprashad Prabhakaran, Mohammad K. Hossain

Transmutation Sciences Materials (TRP)

This paper presents the results of stress corrosion cracking (SCC) studies of two martensitic target materials, namely Alloy EP-823 and Type 422 stainless steel. The susceptibility to SCC was evaluated by using constantload and slow-strain-rate (SSR) test techniques in neutral (pH: 6-7) and acidic (pH: 2-3) aqueous solutions at ambient temperature and 90^oC. A proof ring was used to apply tensile load to the smooth cylindrical specimen for 30 days in constant-load testing. For SSR testing, the specimen was strained in tension until fracture at a strain rate of 3.3 x 10^-6 sec^-1.

Stress Corrosion Cracking Of Type 422 Stainless Steel, Ramprashad Prabhakaran

Transmutation Sciences Materials (TRP)

This paper presents the results of SCC tests of quenched and tempered martensitic Type 422 SS in neutral and acidic aqueous environments at ambient temperature and 90^oC.The susceptibility of smooth and notched tensile specimens to SCC was evaluated by using constant load (CL) and slow strain rate (SSR) test methods. During CL testing, a calibrated proof ring was used to apply a constant load to the test specimen. The magnitude of the applied stress was based on ambient temperature yield strength of the material. On the contrary, the test specimen during SSR testing was continuously strained in tension …

Iodat Analysis Content In Cooking Ingredients Using Iodometry And X-Ray Fluorescence Methods., Nelson Saksono

Makara Journal of Technology

Iodat Analysis Content in Cooking Ingredients Using Iodometry and X-ray Fluorescence Methods. Salt iodization program using iodine fortification into salt method is the best method that is effective and economical to overcome the problems caused by iodine deficiency. However in, its development there are some issues clamed that the use of iodized salt is ineffective since iodine content reduces, even disappear when the salt mix with other cooking ingredients. In order to investigated the existence of iodine in cooking ingredients, a research applying iodometry and X-ray fluorescence methods was carry out. The result obtained by iodometry method showed decreases in …

Emission Gas Reducer On Motor Vehicle, Automobile, Light Engine Of Boat And Stationary Combustion Engine., I Gusti Bagus Wijaya Kusuma

Makara Journal of Technology

Emission gas reducer on motor vehicle, automobile, light engine of boat and stationary combustion engine. The use of motor vehicle should be followed by protection against damages on the environment, since the exhaust gas from combustion engine has significantly affect on air and environmental pollution. One method to solve the problems in air pollution has been done by using a re-heater designed in Mechanical Engineering Department, University of Udayana. In accordance to the test on the re-heater, it can be seen very clear that the re-heater has significantly reduce the CO emission of about 54%. It also reduces the CO2 …

Application Of Remote Sensing For Mapping Soil Organic Matter Content, Bangun Muljo Sukojo, Wahono Wahono

Makara Journal of Technology

Application of Remote Sensing for Mapping Soil Organic Matter Content. Information organic content is important in monitoring and managing the environment as well as doing agricultural production activities. This research tried to map soil organic content in Malang using remote sensing technology. The research uses 6 bands of data captured by Landsat TM (Thematic Mapper) satellite (band 1, 2, 3, 4, 5, 7). The research focuses on pixels having Normalized Difference Soil Index (NDSI) more than 0.3. Ground-truth data were collected by analysing organic content of soil samples using Black-Walkey method. The result of analysis shows that digital number of …

Optimation Model Of Planning Investment Dockyard With Approach Multi Objective Goal Programming, Ali Azhar

Makara Journal of Technology

Optimation model of planning investment dockyard with approach multi objective goal programming. The purpose of this research is to determine decision variable, goal function, alternative priority and achievement function in investment planning. From this optimation component, the model of ship yard investment planning could be achieved. The model of developed model in this research was the optimation of ship yard investment planning using multi objective goal programming approach. The model consist of 5 decision variable, 11 goal function, 2 alternative priority and 11 achievement functions. The model implementation was done toward PT ASSI investment planning. The calculation using from Quantitative …

Self-Ignition Properties Of Peat, Palm Shell Fibre And Woods, Yulianto Sulistyo Nugroho

Makara Journal of Technology

Self-ignition properties of peat, palm shell fibre and woods. Forest fire is one of the greatest environmental problems faced by Indonesia. Forest fires have destroyed million hectares of forest and land which cause economic loss, social problems including smoke related diseases and environmental disaster with long time consequences. The exothermic reactions of forest fuels that lead to fire can be initiated by a piloted flame and low-temperature oxidation mechanism. This paper presents the results of low temperature oxidation studies using forests fuel samples i.e. palm shell fibre, peat, woods and low-rank coal. The measured values of the critical oven temperatures …

The Use Of 2d Plastic Grating For Surface Profile And Dimension Manufacture Product Measurements By Using Ndt Moiré Technique, Retno Wigajatri P., Dini Andiani

Makara Journal of Technology

The Use of 2D Plastic Grating for Surface Profile and Dimension Manufacture Product Measurements by Using NDT Moiré Technique. Research of measuring the shape and dimension of object using the moiré technique have been done. Measurement have been made by observing the moiré space as a result of interaction between grating and its shadow casted on the object’s surface caused by the projector lamp with CCD camera. The acquired data was further processed by way of off-line. By successive phase shifts that is π/2, π dan 3π/2 towards the table tennis ball at the distance of 48 cm from the …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Ii Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Multipacting is one of the major loss mechanisms in rf superconductivity cavities for accelerators. This loss mechanism limits the maximum amount of energy/power supported by the cavities. Optimal designs have been identified in others’ studies. In practice, these designs are not easily manufactured. Chemical etching processes used to polish the cavity walls result in a nonuniform surface etch. A nonuniform surface etch will leave some unclean areas with contaminants and micron size particles. These significantly affect mutipacting. Further, a nonuniform etch will leave areas with damaged grain structure, which is not good for superconducting properties. Typically, the depth of chemical …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (June 1 – August 31, 2002), Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV), the Idaho State University (ISU), and the Los Alamos National Laboratory (LANL) is to evaluate the feasibility of determining residual stresses in cold-worked, plastically-deformed, and welded materials using a nondestructive method based on positron annihilation spectroscopy. This technique uses γ-rays from a small MeV electron Linac to generate positrons inside the sample via pair production. This method is known to have capabilities of characterizing defects in thick specimens, that could not be accomplished by conventional positron technique or other nondestructive methods. The generated data will …

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: I. Swamp Water, Sulistyoweni Widanarko, Henki W. Ashadi, Andri Krisnadi Wicaksono

Makara Journal of Technology

Most of infrastructures using steel concrete to reinforce the strength of concrete. Steel concrete is so vulnerable to chemical compounds that can cause corrosion. It can happen due to the presence of chemical compounds in acid environment in low pH level. These chemical compounds are SO4 2-, Cl-, NO3 -. There are many swamp area in Indonesia. The acid contents and the concentration of ion sulphate, chlorides, and nitrate are higher in the swamp water than in the ground water .The objective of this research was to find out the influence of corrosive chemicals in the swamp water to the …

The Effects Of Corrosive Chemicals On Corrosion Rate Of Steel Reinforcement Bars: Ii. Swamp Sludges, Henki W. Ashadi, Sulistyoweni Widanarko, Irma Gusniani

Makara Journal of Technology

A polluted environment will influence the building age. The objective of this research was to find out the influence of corrosive chemicals within the sludge swamp area with the corrosion rate of steel concrete. Corrosion in steel concrete usually occur in acid area which contain of SO4 2-, Cl- and NO3 -. The research treatment used by emerging ST 37 and ST 60 within 60 days in ‘polluted’ sludge swamp area. Three variation of ‘polluted’ swamp sludge were made by increasing the concentration a corrosive unsure up to 1X, 5X and 10X. The corrosion rate measured by using an Immersion …

The Effect Of Ca Content On Cao-Zeolite On Nitrogen Adsorption Capacity, Mohammad Nasikin, Tania Surya Utami, Agustina Tp Siahaan

Makara Journal of Technology

In industry, Ca zeolite is used as nitrogen selective adsorbent with the use of PSA (Pressure Swing Adsorption)/VSA (Vacuum Swing Adsorption) methods. Natural zeolite modified to be Cao-zeolite by ion exchange process using Ca(OH)2. Adsorption test was done on CaO-zeolite with different Ca concentration to understand how it’s adsorption phenomena on oxygen and nitrogen. Adsorption test has been done for CaO-zeolite with Ca concentration = 0,682%, 0,849% and 1,244% to oxygen and nitrogen with equal concentration seperately. Pressure variation has being done three times (5 minutes long each time) adsorption time to analyze the connection between adsorption time and how …

Cetane Number Booster Additive For Diesel Fuel Synthesized From Coconut Oil, Mohammad Nasikin, Rita Arbianti, Abdul Azis

Makara Journal of Technology

To reduce NOx, SOx, HC, and particulates that produce because of using diesel fuel, can be done by increasing cetane number. One of methods is adding an additive to diesel fuel. 2-Ethyl Hexyl Nitrate (2-EHN) is a commercial additive that an organic nitrate. Making an additive in this research is used palm oil by nitration reaction that used HNO3 and H2SO4. Result of this reaction is methyl ester nitrate that has a structure looks like 2-EHN. IR spectra from research show that methyl ester nitrate is indicated by spectrum NO2 at 1635 cm-1. This result show that methyl ester nitrate …

Analogy Method Development For Cost Estimation Of Software Design, Riyanarto Sarno, Joko Lianto Buliali, Siti Maimunah

Makara Journal of Technology

The important aspect of planning and managing software development project is to estimate the cost of a project. There are several methods for estimating the cost of a software development project, and the Analogy method is a method which gives relatively better estimates. This paper shows that the modified Analogy method selects a closer project reference, estimates more accurate project effort and cost. This study enhances the cost estimate technique by including valid and complete cost parameters, therefore the estimate of a project cost is better than the result of the standard Analogy method.