Materials Science and Engineering Commons^™

Characterization Of Materials Properties In Additively Manufactured Aisi-420 Martensitic Steel Deposited By Laser Engineered Net Shaping, Md Mehadi Hassan

Nanoscience and Microsystems ETDs

Metal additive manufacturing (AM) is a disruptive technology enabling the fabrication of complex and near-net-shaped parts by adding material layer-wise. It offers reduced lead production time. AM processes are finding applications in many industrial sectors such as aerospace, automotive, biomedical, and mold tooling. Despite the tremendous advantages of AM, some challenges still prevent this technology's adoption in high-standard applications. Anisotropy and inhomogeneity in the mechanical properties of the as-built parts and the existence of pores and lack-of-fusion defects are considered the main issues in directed energy deposition (L-DED) parts. Laser-engineered net shaping LENS® offers excellent possibilities to fabricate metal tools …

Additive Manufacturing Of Complexly Shaped Sic With High Density Via Extrusion-Based Technique – Effects Of Slurry Thixotropic Behavior And 3d Printing Parameters, Ruoyu Chen, Adam Bratten, Joshua Rittenhouse, Tian Huang, Wenbao Jia, Ming-Chuan Leu, Haiming Wen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Additive manufacturing of dense SiC parts was achieved via an extrusion-based process followed by electrical-field assisted pressure-less sintering. The aim of this research was to study the effect of the rheological behavior of SiC slurry on the printing process and quality, as well as the influence of 3D printing parameters on the dimensions of the extruded filament, which are directly related to the printing precision and quality. Different solid contents and dispersant- Darvan 821A concentrations were studied to optimize the viscosity, thixotropy and sedimentation rate of the slurry. The optimal slurry was composed of 77.5 wt% SiC, Y2O3 and Al2O3 …

Thermal Post-Processing Of 3d Printed Polypropylene Parts For Vacuum Systems, Pierce Mayville, Aliaksei L. Petsiuk, Joshua M. Pearce

Michigan Tech Publications, Part 1

Access to vacuum systems is limited because of economic costs. A rapidly growing approach to reduce the costs of scientific equipment is to combine open-source hardware methods with digital distributed manufacturing with 3D printers. Although high-end 3D printers can manufacture vacuum components, again, the cost of access to tooling is economically prohibitive. Low-cost material extrusion 3D printing with plastic overcomes the cost issue, but two problems arise when attempting to use plastic in or as part of vacuum systems: the outgassing of polymers and their sealing. To overcome these challenges, this study explores the potential of using post-processing heat treatments …

Ultrafast Stiffening Of Concentrated Thermoresponsive Mineral Suspensions, Sharu Bhagavathi Kandy, Iman Mehdipour, Narayanan Neithalath, Aditya Kumar, Mathieu Bauchy, Edward Garboczi, Samanvaya Srivastava, Torben Gaedt, Gaurav Sant

Materials Science and Engineering Faculty Research & Creative Works

Extrusion-based 3D printing with rapidly hardening polymeric materials is capable of building almost any conceivable structure. However, concrete, one of the most widely used materials for large-scale structural components, is generally based on inorganic binder materials like Portland cement. Unlike polymeric materials, a lack of precise control of the extent and rate of solidification of cement-based suspensions is a major issue that affects the ability to 3D-print geometrically complex structures. Here, we demonstrate a novel method for controllable-rapid solidification of concentrated mineral suspensions that contain a polymer binder system based on epoxy and thiol precursors as well as one or …

Mechanical Properties And Tension-Tension Fatigue Behavior Of A Novel Additively Manufactured Polymer Matrix Composite At Room And Elevated Temperature, Grayson M. Harber

Theses and Dissertations

The tension-tension fatigue behavior of a novel additively manufactured AM carbon fiber reinforced polymer matrix composite was studied. This novel material system consists of T1100 carbon fibers, and a UV photocured resin developed by Continuous Composites and Sartomer. Tensile properties and tension-tension fatigue were investigated for the 090 fiber orientation as well as for the ±45 fiber orientation. Specimens with 0/90 fiber orientation were tested at ambient laboratory temperature 23 °C and at elevated temperature 150 °C, while the specimens with the ±45 fiber orientation were tested only at ambient laboratory temperature. Tension-tension fatigue testing was carried out with a …

Ferrous Alloy Manufacturing For The Martian Surface Through In-Situ Resource Utilization With Ionic Liquids Harvested Iron And Bosch Process Carbon, Blake C. Stewart

Theses and Dissertations

As research continues for the habitation of the Lunar and Martian surfaces, the need for materials for construction of structural parts, mechanical components, and tools remains as a major milestone. The use of in-situ resource utilization (ISRU) techniques is critical due to the financial, physical, and logistical burdens of sending supplies beyond low-Earth orbit. The Bosch process is currently in development as a life support system at the National Aeronautics and Space Administration’s (NASA) Marshall Space Flight Center (MSFC) to regenerate oxygen (O2) from metabolic carbon dioxide (CO2) with the byproduct of elemental carbon (C). The Bosch process presents a …

Solution Synthesis And Additive Manufacturing Of Bismuth Telluride Nanoflakes For Flexible Energy Harvesting, Ariel E. Weltner

Boise State University Theses and Dissertations

Flexible thermoelectric generators (TEGs) are energy harvesting devices which convert temperature differences into electrical power. These devices require no moving parts and offer silent and autonomous operation. The variety of suitable materials covering a broad range of operating temperatures positions TEGs as a promising renewable energy source using waste heat recovery, especially for space and microgravity applications. Conventional manufacturing of flexible electronic and thermoelectric devices requires complicated and relatively expensive processing, which limits the capabilities of in-space manufacturing. Additive manufacturing (AM) expands the use of flexible electronics to new surfaces, applications, and recently, low gravity conditions. Plasma jet printing (PJP) …

Flow In Additively Manufactured Super-Rough Channels, Samuel Altland, Xiaowei Zhu, Stephen Mcclain, Robert Kunz, Xiang Yang

Mechanical and Materials Engineering Faculty Publications and Presentations

Metal additive manufacturing has enabled geometrically complex internal cooling channels for turbine and heat exchanger applications, but the process gives rise to large-scale roughness whose size is comparable to the channel height (which is 500 μm). These super-rough channels pose previously unseen challenges for experimental measurements, data interpretation and roughness modelling. First, it is not clear if measurements at a particular streamwise and spanwise location still provide accurate representation of the mean (time- and plane-averaged) flow. Second, we do not know if the logarithmic layer survives. Third, it is unknown how well previously developed rough-wall models work for these large-scale …

Tini-Based Bi-Metallic Shape-Memory Alloy By Laser-Directed Energy Deposition, Yitao Chen, Cesar Ortiz Rios, Braden Mclain, Joseph William Newkirk, Frank W. Liou

Materials Science and Engineering Faculty Research & Creative Works

In this study, laser-directed energy deposition was applied to build a Ti-rich ternary Ti–Ni–Cu shape-memory alloy onto a TiNi shape-memory alloy substrate to realize the joining of the multifunctional bi-metallic shape-memory alloy structure. The cost-effective Ti, Ni, and Cu elemental powder blend was used for raw materials. Various material characterization approaches were applied to reveal different material properties in two sections. The as-fabricated Ti–Ni–Cu alloy microstructure has the TiNi phase as the matrix with Ti2Ni secondary precipitates. The hardness shows no high values indicating that the major phase is not hard intermetallic. A bonding strength of 569.1 MPa was obtained …

Additive Manufacturing Of Variable Contrast Computed Tomography Anatomical Phantoms Using A Single Feedstock In Fused Filament Fabrication, Cory J. Darling

LSU New Orleans Theses and Dissertations

Anatomical phantoms used in biomedical education and training benefit greatly from Fused filament fabrication’s (FFF) ability to rapidly produce complex and unique models. Current materials and methods used in FFF have limited ability to accurately produce phantoms that can mimic the radiological properties of multiple biological tissues. This research demonstrates that the CT contrast of FFF produced models can be modified by varying the concentration of bismuth oxide in acrylonitrile butadiene styrene (ABS) filaments and a tunable CT contrast that mimics the CT contrast ranging from fatty tissue to cortical bone using a single composite filament without introducing artificial image …

Effects Of Sizing Agents On Mechanical Properties Of Carbon Fiber–Polymer Composites Via Fused Filament Fabrication Additive Manufacturing., Benjamin D. Mitchell

Electronic Theses and Dissertations

This study demonstrated the effects of changing the sizing agent parameter during the preparation of carbon fibers on the mechanical properties of composite made with acrylonitrile butadiene styrene (ABS) as the matrix material and carbon fibers as the fiber material. Three types of sizing agents produced by Allnex were used to coat three different batches of carbon fibers that were mixed with a torque rheometer and extruded with a barrel-style melt extruder into continuous spools of 1.75 mm filament for use with commercial 3D printers. Tensile tests were conducted on the filaments and tensile bars printed from the materials. Results …

Additive Manufacturing Of Sensors For Extreme Environments, Kiyo Tiffany Fujimoto

Boise State University Theses and Dissertations

Advanced manufacturing based direct-write technologies have emerged as the predominant enabler for the fabrication of active and passive sensors for use in harsh operating environments. The ability to directly write and integrate electronic components onto physical packaging can be achieved with additive manufacturing (AM) methods such as direct write technologies (DWT) which include aerosol jet printing (AJP), Ink Jet Printing (IJP), Plasma Jet Printing (PJP), and Micro-Dispense Printing (MDP). In this work, we investigate the use of these methods to accelerate, modernize, and enhance the functionality of sensors and instrumentation to achieve the goal of improving the safety and efficiency …

Potential Solution To Meet Growing Demands Of Refractory Metal: Selective Laser Melting Of Molybdenum-Tungsten Alloy, Jae Yu

Theses and Dissertations

Selective laser melting (SLM) of refractory metals has been of high interest in research due to the metals’ potential desirable characteristics in aeronautical and space applications. In particular, molybdenum and tungsten have been the focus of several studies in the search for high temperature and high strength purposes in applications like supersonic aircraft, re-entry vehicles, nuclear fission, power generation, and other space systems. However, there is still a significant knowledge gap to process defect-free alloys and making use of them in practical engineering functions. The aim of this study is to characterize the relationship between the microstructure and mechanical properties …

Additive Manufacturing Waste Management System - Plastic Extrusion Process, Gabriel Bennett, Lindsay Liebrecht, David Lyogky, Wilson Woods

Williams Honors College, Honors Research Projects

3D printing is a fast-growing market with its main source of waste being PLA and ABS plastics. In 2019, the global additive manufacturing market grew to over $10.4 billion, crossing the pivotal double-digit billion threshold for the first time in its nearly 40-year history. (SmarTech Analysis, 2020 Additive Manufacturing Market Outlook and Summary of Opportunities Report). The waste is generated from failed prints and rejected support structures which are common occurrences for personal use. Plastic recycling has become one of the leading discussions of environmental protection and waste management. The 3D market currently does not offer an effective and affordable …

Additive Manufacturing Of Continuous Carbon Fiber-Reinforced Sic Ceramic Composite With Multiple Fiber Bundles By An Extrusion-Based Technique, Ruoyu Chen, Adam Bratten, Joshua Rittenhouse, Ming-Chuan Leu, Haiming Wen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Due to the high cost, complex preparation process and difficulty in structural design, the traditional methods for carbon fiber reinforced SiC ceramic composite preparation have great limitations. This paper presents a technique for the additive manufacturing multiple continuous carbon fiber bundle-reinforced SiC ceramic composite with core-shell structure using an extrusion-based technique. A conventional nozzle system was modified to print simultaneously a water based SiC paste with continuous carbon fibers. Different levels of binder contents were investigated to optimize the stickiness, viscosity, thixotropy and viscoelasticity of the paste. After sintering, SiC whiskers were generated on the surface of fiber, which is …

Functionally Magnetic Gradient Copper-Nickel Material Fabricated Via Directed Energy Deposition, Vy Tran Phuong Nguyen

Graduate Theses, Dissertations, and Problem Reports (ETD)

Functionally gradient materials (FGMs) of CuSn10 and Inconel 718 were fabricated via a hybrid directed energy deposition (DED) system. The objective of the present thesis is to determine the feasibility of manufacturing CuSn10 and Inconel 718 FGMs via DED and investigate the physical and mechanical properties and the microstructures of the resulting FGMs. The physical tests comprised of conductivity and Seebeck coefficient measurements. The microstructure analysis and mechanical testing include microscopic imaging, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and hardness test. In addition, compressive strength test was performed to analyze the interface bonding behaviors.

Processing To Enable Direct-Write Additive Manufacturing Of Ceramics And Ceramic Composites, Austin Martin

Doctoral Dissertations

"This research focuses on the processing of novel feedstocks for and during direct-write additive manufacturing (AM), specifically the direct ink writing (DIW) and Ceramic On-Demand Extrusion (CODE) manufacturing processes, in order to produce ceramic and ceramic-based composite components. Strongly dispersed, concentrated (φ = 0.42), nanoparticle (d₅₀ ~0.3 µm), zirconia (ZrO₂) pastes were used to print densely filled, large continuous volume (≳ 1 cm³) ceramic components. An elastic shear modulus (G’) of 56,000 Pa and yield stresses between 6 and 10 Pa allowed for printed components of 34.5 mm in height over 115 layers without slumping …

Plasma Spheroidization Of Gas-Atomized 304l Stainless Steel Powder For Laser Powder Bed Fusion Process, M. Hossein Sehhat, Austin T. Sutton, Chia-Hung Hung, Ben Brown, Ronald J. O'Malley, Jonghyun Park, Ming-Chuan Leu

PSMRC Faculty Research

Particles of AISI 304L stainless steel powder were spheroidized by the induction plasma spheroidization process (TekSphero-15 spheroidization system) to assess the effects of the spheroidization process on powder and part properties. The morphology of both as-received and spheroidized powders was characterized by measuring particle size and shape distribution. The chemistry of powders was studied using inductively coupled plasma optical emission spectroscopy for evaluation of composing elements, and the powder’s microstructure was assessed by X-ray diffraction for phase identification and by electron backscattered diffraction patterns for crystallography characterization. The Revolution Powder Analyzer was used to quantify powder flowability. The mechanical properties …

Fatigue Damage Quantification And Life Estimation With Provision For Microstructure, Arash Pourbagheri Jirandehi

LSU Doctoral Dissertations

This dissertation provides methodologies for the quantification of different forms of fatigue damage by considering the role of microstructure. The laws of thermodynamics in conjunction with Finite Element Method (FEM) are utilized to devise thermodynamically-base frameworks for the estimation of cyclic damage in polycrystalline metals. Accordingly, a microstructure-sensitive platform for fatigue life estimation is introduced. The proposed framework is assessed for 3D printed metallic alloys at room and elevated temperatures. Further, it is used to analyze the fatigue performance difference between additively manufactured Inconel 718 in three print orientations. This research is of fundamental vital interest because it ensures that …

Additive Manufacturing Of Miniaturized Peak Temperature Monitors For In-Pile Applications, Kiyo T. Fujimoto, Yaqiao Wu, David Estrada

Materials Science and Engineering Faculty Publications and Presentations

Passive monitoring techniques have been used for peak temperature measurements during irradiation tests by exploiting the melting point of well-characterized materials. Recent efforts to expand the capabilities of such peak temperature detection instrumentation include the development and testing of additively manufactured (AM) melt wires. In an effort to demonstrate and benchmark the performance and reliability of AM melt wires, we conducted a study to compare prototypical standard melt wires to an AM melt wire capsule, composed of printed aluminum, zinc, and tin melt wires. The lowest melting-point material used was Sn, with a melting point of approximately 230 °C, Zn …

Laser-Defined Graphene Strain Sensor Directly Fabricated On 3d-Printed Structure, Tyler M. Webb, Twinkle Pandhi, David Estrada

Materials Science and Engineering Faculty Publications and Presentations

A direct-write method to fabricate a strain sensor directly on a structure of interest is reported. In this method, a commercial graphene ink is printed as a square patch (6 mm square) on the structure. The patch is dried at 100 °C for 30 min to remove residual solvents but the printed graphene remains in an insulative state. By scanning a focused laser (830 nm, 100 mW), the graphene becomes electrically conductive and exhibits a piezoresistive effect and a low temperature coefficient of resistance of −0.0006 °C⁻¹. Using this approach, the laser defines a strain sensor pattern on …

Mechanical Properties And Microstructure Characteristics Of Alloy Parts Produced By Laser Powder Bed Fusion (Lpbf) Method, Hong Yao

LSU Doctoral Dissertations

Additive manufacturing (AM) is a rapid prototyping technology to produce fully functional and complex designing objects. As one of the AM methods, Laser Powder Bed Fusion (LPBF) has gained the most attention from both academic researchers and industrial companies. During the LPBF process, metal powders are applied layer by layer, which can be 20 microns to 50 microns in thickness. After a layer is prepared, a high-power laser, which is commonly controlled by a scanning head, is used to selectively melt the interested area of a 2D geometry which is designed in a computer aided designing software. LPBF method can …

Optimization Of 3d Printed Mold Performance For Injection Molding Via Hollow Infill Patterns, Alan Fong

University Honors Theses

The applicability of hollow infill patterns has been explored for its applications in making 3D printed polymer-based injection molds in the additive manufacturing industry. Hollow infill patterns offer a significant reduction in material costs as well as the opportunity for reducing the cooling times via pumping a coolant fluid through the hollow cavity in a similar fashion to traditional conformal cooling channels. A 3D Jacks Support Hollow mold model was determined to be the best performing design. FEA analysis was conducted to determine the maximum reduction in internal volume (percentage of material saved) that could be achieved without exceeding the …

Open Source 3d-Printable Planetary Roller Screw For Food Processing Applications, Marcello C. Guadagno, Jacob M. Loss, Joshua M. Pearce

Michigan Tech Publications, Part 1

Historically, open source agriculture (OSA) was based on grassroots technology generally manufactured by hand tools or with manual machining. The rise of distributed digital manufacturing provides an opportunity for much more rapid lateral scaling of open source appropriate technologies for agriculture. However, the most mature distributed manufacturing area is plastic, which has limited use for many OSA applications. To overcome this limitation with design, this study reports on of a completely 3D-printable planetary roller screw linear actuator. The device is designed as a parametric script-based computer aided design (CAD) package to allow for the easy adaption for a number of …

Quality Assurance Of Lightweight Structures Via Phase-Based Motion Estimation, Ikenna E. Ifekaonwu

College of Graduate Studies: Theses & Dissertations

In recent years, lightweight structures have become mature and adopted in various applications. The importance of quality assurance cannot be overemphasized hence extensive research has been conducted to assess the quality of lightweight structures. This study investigates a novel process that exploits motion magnification to investigate the damage characteristics of lightweight mission-critical parts. The goal is to assure the structural integrity of 3D printed structures and composite structures by determining the inherent defects present in the part by exploiting their vibration characteristics. The minuscule vibration of the structure was recorded with the aid of a high-speed digital camera, and the …

Understanding Flow Characteristics In Metal Additive Manufacturing, Carl R. Hartsfield, Travis E. Shelton, Gregory R. Cobb, Ryan A. Kemnitz, Joseph Weber

Faculty Publications

In fluid flow, the frictional effects from interior surfaces of flow components create pressure loss across the surface. Understanding this inherent pressure loss due to friction and other phenomena is important when designing a flow system. For conventional manufacturing, friction loss has been empirically studied and is well known in the engineering community. However, newer manufacturing techniques, such as laser powder bed fusion (LPBF), an additive manufacturing technique, need to be understood. The inherent flow conditions resulting from the additive processes were studied. Test samples were printed with the flow path oriented in the vertical direction with different channel diameters …

Design, Fabrication, And Reliability Effects Of Additively Manufactured First Level Compliant Interconnects For Microelectronics Application, Tumininu David Olatunji

Graduate Theses and Dissertations

Semiconductor packaging and development is greatly dependent on the magnitude of interconnect and on-chip stress that ultimately limits the reliability of electronic components. Thermomechanical related strains occur because of the coefficient of thermal expansion mismatch from different conjoined materials being assembled to manufacture a device. To curb the effect of thermal expansion mismatch between conjoined parts, studies have been done in integrating compliant structures between dies, solder balls, and substrates. Initial studies have enabled the design and manufacturing of these structures using a photolithography approach which involves a high number of fabrication steps depending on the complexity of the structures …

Modeling And Analysis For Unit Cell Size, Material Anisotropy And Material Imperfection Effects Of Cellular Structures Fabricated By Powder Bed Fusion Additive Manufacturing., Yan Wu

Electronic Theses and Dissertations

Cellular structures are networks of interconnected struts or walls with porosities and are widely found in many natural load-bearing structures such as plants and bones. Cellular structures offer unique functional characteristics such as high stiffness to weight ratio, tailorable heat transfer coefficient, and enhanced mechanical energy absorption, which makes them highly attractive in various engineering disciplines such as biomedical implants, electrodes, heat exchangers, and lightweight structures. There exists an abundance of literatures that have investigated various mechanical properties of various cellular structures such as Poisson’s ratio, elastic modulus, ultimate strength, yield strength, and failure characteristics. Based on the classic cellular …

Additive Manufacturing Of Graphene-Based Devices For Flexible Hybrid Electronics, Twinkle Pandhi

Boise State University Theses and Dissertations

In this work, I investigate and enhance the fundamental sensing properties of printed electronic nanomaterials (e.g., graphene) in real-world environments while decreasing weight, cost, and power consumption. The dissertation addresses this issue with the following foci in mind: (1) developing a straightforward and repeatable process to synthesize graphene ink which is also compatible with Inkjet-printing (IJP) and Aerosol Jet printing (AJP). (2) Tuning additive manufacturing printing (IJP and AJP) parameters to establish a repeatable manufacturing process and print high performing (graphene-based) electrodes and interconnects, compatible with the underlying substrate. (3) Investigate power dissipation and electrical breakdown in AJP printed graphene …

The Effect Of Compaction Temperature And Pressure On Mechanical Properties Of 3d Printed Short Glass Fiber Composites, Pushpashree Jain Ajith Kumar Jain

Mechanical & Aerospace Engineering Theses & Dissertations

Among many thermoplastics that are used in engineering, polyamide 6 (nylon 6) is an extremely versatile engineering thermoplastic. Nylon filled with glass fibers has higher mechanical strength and high wear resistance than general purpose nylon. 3D printed composites, based on fused filament modeling, typically suffer from poor bead-to-bead bonding and relatively high void content, limiting their mechanical properties

This thesis explores the effect of compaction pressure and temperature on improving the mechanical properties of 3D printed composites. Engineering moduli in the printing and transverse to printing direction, as well as ultimate strength were measured using the tensile testing with Digital …