Materials Science and Engineering Commons^™

Using Dft On Ultrasound Measurements To Determine Patient-Specific Blood Flow Boundary Conditions For Computational Hemodynamics Of Intracranial Aneurysms, Hang Yi, Zifeng Yang, Luke Bramlage, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

Boundary conditions (BCs) is one pivotal factor influencing the accuracy of hemodynamic predictions on intracranial aneurysms (IAs) using computational fluid dynamics (CFD) modeling. Unfortunately, a standard procedure to secure accurate BCs for hemodynamic modeling does not exist. To bridge such a knowledge gap, two representative patient-specific IA models (Case-I and Case-II) were reconstructed and their blood flow velocity waveforms in the internal carotid artery (ICA) were measured by ultrasonic techniques and modeled by discrete Fourier transform (DFT). Then, numerical investigations were conducted to explore the appropriate number of samples (N) for DFT modeling to secure the accurate BC by comparing …

Predicting Rheology Of Uv-Curable Nanoparticle Ink Components And Compositions For Inkjet Additive Manufacturing, Cameron D. Lutz

Master's Theses

Inkjet additive manufacturing is the next step toward ubiquitous manufacturing by enabling multi-material printing that can exhibit various mechanical, electronic, and thermal properties. These characteristics are realized in the careful formulation of the inks and their functional materials, but there are many constraints that need to be satisfied to allow optimal jetting performance and build quality when used in an inkjet 3-D printer. Previous research has addressed the desirable rheology characteristics to enable stable drop formation and how the metallic nanoparticles affect the viscosity of inks. The contending goals of increasing nanoparticle-loading to improve material deposition rates while trying to …

Photodegradation Of Microplastics Through Nanomaterials: Insights Into Photocatalysts Modification And Detailed Mechanisms, Yiting Xiao, Yang Tian, Wenbo Xu, Jun Zhu

Biological and Agricultural Engineering Faculty Publications and Presentations

Microplastics (MPs) pose a profound environmental challenge, impacting ecosystems and human health through mechanisms such as bioaccumulation and ecosystem contamination. While traditional water treatment methods can partially remove microplastics, their limitations highlight the need for innovative green approaches like photodegradation to ensure more effective and sustainable removal. This review explores the potential of nanomaterial-enhanced photocatalysts in addressing this issue. Utilizing their unique properties like large surface area and tunable bandgap, nanomaterials significantly improve degradation efficiency. Different strategies for photocatalyst modification to improve photocatalytic performance are thoroughly summarized, with a particular emphasis on element doping and heterojunction construction. Furthermore, this review …

Waste Illuminates Worlds: Printed Modular Lamp Design Based On Brick And Clay Tile, Yechen Zhu

Masters Theses

The building industry in the New England area is often in a state of entropy, with abandoned brick buildings contributing to urban decay. The recycling rate of brick and clay tile wastes generated by construction and demolition is only 12.2%, meaning the majority is sent to landfills. The expansion of landfills can lead to significant environmental and community challenges, including increased traffic from waste transport, habitat destruction, ecosystem degradation, and contributions to climate change. Specifically, the Bethlehem landfill in New Hampshire, which is planned to undergo a 5.71-acre lateral expansion through 2026, has already encountered issues such as leachate spills …

Using Micromoments And Concept Maps To Enhance Entrepreneurially Minded Learning Of Indoor Air Pollution Control, Jean M. Andino, Erick Salvador Vasquez-Guardado, Ricardo Gomez Gonzalez, Xiaojing Yuan, Nilza D. Aples

Chemical and Materials Engineering Faculty Publications

Micromoments targeted toward indoor air quality were introduced to students in an Air Quality Engineering course to enhance their entrepreneurial mindset. Three micromoment activities, i.e., “Question Frenzy”, “Make It Relevant”, and “How Do We Make It Better?” that are linked, respectively, to the curiosity, connections, and creating value elements of EM were deployed in the class in the context of the use of a Corsi Rosenthal cube (a do-it-yourself structure that has recently become popular as an inexpensive way to reduce indoor particle pollution). Students generated concept maps pre-and post- micromoment intervention using the freely available CMap Tools software. The …

Polypropylene As Partial Fine Aggregate Substitute In Concrete, Samuel E. Royston, Chrisitan G. Achkar, Nicholas B. Tabarez

Architectural Engineering

The objective of this project is to discover a structurally effective method in repurposing recyclable plastic waste through its partial substitution for traditional fine aggregate in concrete.

Results obtained from analysis indicate a 25 percent compressive strength reduction with polypropylene at a 10 percent partial substitution for total sand content. This material successfully performed as an alternative, presenting a ductile mode of failure.

Three material alternatives - polypropylene, polyethylene, and rubber - were substituted for a percentage of sand. These materials underwent concrete cylinder crushing tests to determine their ultimate crushing strength, with the intent of identifying the most effective …

Design, Modeling, And Testing Of A Novel Inductor For Electric Vehicles: Iron Nitride Soft Magnetic Composites, Cody Krawczyk, Lauren Walker

Materials Engineering

The purpose of this study is to develop a processing method to reduce the porosity of toroidal inductors, whose cores are composed of soft magnetic composites (SMCs) with 65 vol.%, 75 vol.%, and 85 vol.% iron nitride (γ′-Fe₄N) and to validate the results with a COMSOL^TM model. Using hot-pressing as the main process of manufacture, fourteen samples were fabricated and eight were wound with Litz wire. Four samples of 75 vol.% and four samples of 85 vol.% were fabricated by mixing the Fe₄N powder and epoxy at 150^oC and initially pressing at 5 …

Characterization Of High Albedo Ground Surface Treatments For Energy Harvesting By Bifacial Photovoltaic Power Plants, Roma C. Chatripally, Matthew Honda, James Vance

Materials Engineering

Bifacial photovoltaic (bPV) cells have higher solar efficiency than monofacial photovoltaic (mPV) cells due to having two sides of active layers. bPV cells also require less space to produce equivalent electricity, which is useful for solar farms that want to maximize energy output per unit area. Placing a sheet of highly reflective material on the surface beneath bPV cells further increases their efficiency due to increasing the amount of solar radiation that reaches the underside of the bPV cells. This study explores the effects of natural outdoor weathering, solar altitude angle, and accelerated exposure to UV radiation on the albedos …

Metallurgical Impact Of Switching From Hammer Units To Hydraulic Presses For Forging, Cole Hawker, Jacob Reed

Materials Engineering

Carlton Forge Works (CFW) is evaluating the retirement of its hammer units in favor of hydraulic presses to address safety concerns in forging aerospace components. This paper investigates the metallurgical implications of this transition, emphasizing the importance of superior microstructures and meeting industry standards and customer requirements. The alloys in question are Titanium-6Al-4V (Ti64) and Inconel 718 (INCO 718), which comprise a majority of CFW’s production. Ti64's high specific strength and thermal stability make it ideal for aerospace applications, while INCO 718 is recognized for superior high-temperature creep performance. Defects like freckles and white spots in INCO 718 are analyzed …

Printed Graphite Electrodes For Fast-Charging Lithium-Ion Batteries, Guanyi Wang

Dissertations

The rapid growth of the electric vehicle (EV) market has demanded lithium-ion batteries (LIBs) with high energy density and fast charging capability. However, charging energy-dense LIBs with thick graphite electrodes at high current densities is typically facing challenges and leading to adverse performance, such as low energy density, short cycle life, rapid temperature rises and safety issues. The root cause is the onset of Li plating. During fast charging application, the sluggish lithium ions accumulated at the surface of graphite due to kinetic limitation and formed Li plating, especially when lithiated to a high state of charge (SOC). It has …

Comparison Of Pm-Hip To Forged Sa508 Pressure Vessel Steel Under High-Dose Neutron Irradiation, Wen Jiang, Yangyang Zhao, Yu Lu, Yaqiao Wu, David Frazer, Donna P. Guillen, David W. Gandy, Janelle P. Wharry

Materials Science and Engineering Faculty Publications and Presentations

Powder metallurgy with hot isostatic pressing (PM-HIP) is an advanced manufacturing process that is envisioned to replace forging for heavy nuclear components, including the reactor pressure vessel (RPV). But PM-HIP products must at least demonstrate comparable irradiation tolerance than forgings in order to be qualified for nuclear applications. The objective of this study is to directly compare PM-HIP to forged SA508 Grade 3 Class 1 low-alloy RPV steel at two neutron irradiation conditions: ∼0.5–1.0 displacements per atom (dpa) at ∼270 °C and ∼370 °C. PM-HIP SA508 experiences greater irradiation hardening and embrittlement (total elongation) than forged SA508. However, uniform elongation …

Assessing Global Engagement Interventions To Advance Global Engineering Competence For Engineering Formation, Scott Schneider, Erick S. Vasquez-Guardado, Corinne Mowrey, Michael Moulton, Homero Murzi, Matthew A. Witenstein

Chemical and Materials Engineering Faculty Publications

This paper summarizes the work performed during the first year of a collaborative Research Initiation in Engineering Formation (RIEF) project focused on assessing the formation of a global learner mindset in engineering students through the use of different types of global engagement interventions without extended international travel. During this year the global engagement interventions have been developed, piloted, and assessed using the Global Engagement Survey (GES) and Global Engineering Competency Scale (GECS) instruments in a pre and post format. The assessment results helped the research team update the interventions and refine the assessment strategy, including the addition of new qualitative …

Work In Progress: Exploring The Impact Of International Experiences On The Development Of Students’ Entrepreneurial Mindset, Olgha Bassam Qaqish, Marcia Poole, William Pennock, Erick S. Vasquez-Guardado, Fahmidah Ummul Ashraf

Chemical and Materials Engineering Faculty Publications

International experiences, including collaborative online international learning (COIL) experiences that naturally increase accessibility, are of interest to many undergraduate students. These experiences provide educators a unique opportunity to develop a student's entrepreneurial mindset (EM). Additionally, hands-on experiences aligned with the National Academy of Engineering’s (NAE) grand challenge themes (Sustainability, Security, Health, and Joy of Living) support connections between the experience, disciplinary knowledge, multicultural awareness, and EM. Through this Work-in-Progress (WiP) study, we seek to answer: 1) How do international experiences influence undergraduate science and engineering students’ EM, and 2) How does the international experience modality (i.e., study abroad or COIL) …

Enhancing Entrepreneurial Minded Learning Of Process Control And Heat Transfer Concepts Using Micromoments And Concept Maps, Erick S. Vasquez-Guardado, Ricardo Gomez Gonzalez, Jean M. Andino, Nilza D. Aples, Xiaojing Yuan

Chemical and Materials Engineering Faculty Publications

The Entrepreneurially Minded Learning (EML) Framework seeks to infuse an Entrepreneurial Mindset in engineering students. The EML framework is founded on the 3 C’s principles of curiosity, connections, and creating value. Assessing EML efforts, however, is a well-known challenge for many engineering courses that do not have a design component. Through concept maps and micromoment activities, this work seeks to answer the following questions: Does implementing micromoment activities enhance students’ EML in two core areas of chemical engineering, i.e., heat transfer and process controls? A secondary research question is whether introducing a physical device in lectures enhances students’ EML. The …

In Situ And 2d And 3d In Silico Redox Cycling Studies For Design Optimization Of Coplanar Arrays Of Microband Electrodes In A 70 Μm × 100 Μm Electroactive Footprint, Miguel Angel Abrego Tello, Mahsa Lotfi Marchoubeh, Ingrid Fritsch

Chemistry & Biochemistry Faculty Publications and Presentations

Optimization of redox-cycling currents was performed by adjusting the height (sidewalls, h), width (w), and length (l) of band electrodes and their spacing (w_gap) in coplanar arrays restricted to a small-electroactive window of 70 × 100 μm. These arrays can function in μL-volumes for chemical analysis (e.g., in-vivo dopamine detection using probes). Experiments were conducted with an array of five electrodes (NE = 5), w = 4.3 μm, w_gap = 3.7 μm, h = 0.150 μm, and l = 99.2 μm. Reasons for …

Modeling Charging Current Dynamics At Microelectrodes And Their Interfaces With Electrolyte And Insulators With A Focus On Microfabricated Gold Microband Electrodes On An Su-8 Substrate, Miguel Angel Abrego Tello, Mahsa Lotfi Marchoubeh, Ingrid Fritsch

Chemistry & Biochemistry Faculty Publications and Presentations

The suitability of electrochemical methods for quantitative measurements at microdevices is influenced by the relatively large electrode-insulator interface-to-electrode area ratio, greatly impacting charging dynamics due to interactions among electrolyte, conductor material, and insulator layers. The resulting charging current can overwhelm the faradaic current from redox chemistry. The device studied here features a 70 μm × 100 μm electroactive window, hosts gold coplanar microband electrodes, and is insulated by SU-8, which serves as both overlayer and substrate. The overlayer defines the electroactive length and isolates the leads of the electrodes from the sample solution. Cyclic voltammetry in 0.10 M …

Settingsorder Article Reprints Open Accesseditor’S Choicearticle Exploring The Impact Of Spray Process Parameters On Graphite Coatings: Morphology, Thickness, And Tribological Properties, Adedoyin Abe, Josue A. Goss, Min Zou

Mechanical Engineering Faculty Publications and Presentations

This study explores, through a full factorial experimental design, the effects of graphite concentration and spray flow rate on the morphology, thickness, and tribological performance of graphite coatings for potential tribological applications. Coatings were applied to rough substrates using varying concentrations and flow rates, followed by analysis of their morphological characteristics, roughness, thickness, coefficient of friction (COF), and wear behavior. The results revealed distinct differences in the coating morphology based on flow rate, with low-flow-rate coatings exhibiting a porous structure and higher roughness, while high-flow-rate coatings displayed denser structures with lower roughness. A COF as low as 0.09 was achieved, …

Scaffold-Free Development Of Multicellular Tumor Spheroids With Spatial Characterization Of Structure And Metabolic Radial Profiles, Shelby N. Bess, Gaven K. Smart, Matthew J. Igoe, Timothy J. Muldoon

Biomedical Engineering Faculty Publications and Presentations

Purpose

In vitro assays are essential for studying cellular biology, but traditional monolayer cultures fail to replicate the complex three-dimensional (3D) interactions of cells in living organisms. 3D culture systems offer a more accurate reflection of the cellular microenvironment. However, 3D cultures require robust and unique methods of characterization.

Methods

The goal of this study was to create a 3D spheroid model using cancer cells and macrophages, and to demonstrate a custom image analysis program to assess structural and metabolic changes across spheroid microregions.

Results

Structural characterization shows that cells at the necrotic core show high normalized fluorescence intensities of …

Non-Linear Modeling Of Hysteresis In Piezoelectric Actuated Cantilever Beam Using The Bouc-Wen Model, Andrew Donald Maas

Master's Theses

Piezoelectric actuators frequently exhibit a time-dependent behavioral phenomenon known as hysteresis, resulting in a lag in the deformation of the actuator compared to linear models. The presence of hysteresis complicates control systems involving piezoelectric actuators. However, traditional modeling methods for piezoelectric actuated smart structures often treat the piezoelectric patches as linear actuators without considering hysteresis, leading to suboptimal controller performance.

This thesis aims to establish a comprehensive model by integrating the Euler-Bernoulli beam bending model with the hysteresis dynamics induced by two opposing piezoelectric patches attached to a beam. A model expansion method is employed to transform the partial differential …

Interaction Of Particles With Plasma And Shock Produced By Pulsed Spark Discharge, Shomik Mukhopadhyay

Dissertations

Interactions of powders with high-temperature plasma and shockwaves occur in diverse scenarios, such as nuclear blasts, accidental industrial dust explosions, solid propellant combustion in explosive charges and when removing contaminants from surfaces. Electrostatic Discharge (ESD), known for generating shock and plasma, is a promising lab-scale technique for simulating these interactions. Studies with ESD involved placing powders near a spark-producing gap between electrodes and observing mechanical and chemical processes like particle motion and ignition. A limited range of spark conditions and material properties have been tested, which facilitated the development and validation of preliminary computational models describing this system. Significant gaps …

Methodology For Developing Biodegradable Polymer Blends And Composites For Agriculture, Fangzhong Xing

Theses

The use of polyethylene (PE) films to improve soil conditions and to increase crop yield has produced microplastics that are harmful to our ecosystem. The overall objective of this thesis is to develop an effective biodegradable polymer/composite to replace PE, and hence, to reduce microplastic pollution. The focus of this research is to develop a systematic protocol for assessing the suitability of the biodegradable films based on industry standards in agriculture. For this purpose, a range of biodegradable polymer blends are prepared using polylactic acid (PLA) and polybutylene adipate-co-terephthalate (PBAT) with varying PLA to PBAT ratios. Solvent casting combined with …

Effect Of Antioxidant Additives And Recycling Agents On Performance Of Asphalt Binders And Mixtures, Phase I, Nitish R. Bastola, Mahdieh Khedmati, Hamzeh Haghshenas, Jamilla Teixeira

Nebraska Department of Transportation: Research Reports

The use of reclaimed asphalt pavement (RAP) in asphalt mixtures has notably increased in recent times. Nevertheless, the inherent stiff and aged characteristics of RAP materials have consistently raised concerns regarding cracking performance. The use of recycling agents (RAs) has gained popularity in recent years since they can effectively modify the engineering properties of the aged asphalt binder. Besides that, the combination of RA with antioxidant (AO) additives has shown promise in enhancing the long-term performance of RAP mixtures. This research aims to investigate the effect of various RAs and one AO additive on performance of asphalt binders and high-RAP …

Electrochemical Nitrate Reduction To Ammonia On Cu Based Nanoparticles Using Quantum Mechanical Simulations, Kathan Bhavin Shukla

Theses

Nitrate reduction to ammonia (NRA) is critical for environmental remediation and energy conservation, as it can remove harmful nitrate (NO₃^-) from water sources while producing usable ammonia (NH₃). Cu represents one of the most promising non-noble-metal NRA electrocatalysts. However, the intrinsic catalytic activity of Cu facets and their influence under different pH conditions remain unclear, particularly in the presence of ions commonly found in wastewater such as Cl^-, Na⁺, Mg²⁺, and Ca²⁺. Using density functional theory (DFT) calculations, we evaluated the nitrate reduction to ammonia (NRA) pathways …

Impact Of Polymer Structure In Polyurethane Topcoats On Anti-Icing Properties, Donghyeon Lee, Junho Park, Min Ji Woo, Juhyeong Lee, Joung-Man Park, Hyung Mi Lim, Tae Kyung Lee, Seong Baek Yang, Sang Yong Nam, Dong-Jun Kwon

Mechanical and Aerospace Engineering Faculty Publications

Icing on the topcoat layer of structures or mobility systems can be a factor leading to functional failures or accidents. Material engineering approach to prevent icing involves creating hydrophobic surfaces. In this study, it was confirmed that the method of controlling the structure of polymers using solvents to adjust surface hydrophobicity and ice prevention effects is effective. Polyurethane (PU) topcoats are primarily used on the exterior of mobility devices; therefore, structure of PU was manipulated using xylene. Through the adjustment of the ratio between PU and xylene, changes in the curing enthalpy and crystal structure were observed, which led to …

Rheological Properties And 3d Printing Behavior Of Pcl And Dmso2 Composites For Bio-Scaffold, Jae-Won Jang, Kyung-Eun Min, Cheolhee Kim, Chien Wern, Sung Yi

Mechanical and Materials Engineering Faculty Publications and Presentations

The significance of rheology in the context of bio three-dimensional (3D) printing lies in its impact on the printing behavior, which shapes material flow and the layer-by-layer stacking process. The objective of this study is to evaluate the rheological and printing behaviors of polycaprolactone (PCL) and dimethyl sulfone (DMSO₂) composites. The rheological properties were examined using a rotational rheometer, employing a frequency sweep test. Simultaneously, the printing behavior was investigated using a material extrusion 3D printer, encompassing varying printing temperatures and pressures. Across the temperature range of 120–140 °C, both PCL and PCL/DMSO₂ composites demonstrated liquid-like behavior, …

Artificial Neural Network-Based Modelling For Yield Strength Prediction Of Austenitic Stainless-Steel Welds, Sukil Park, Cheolhee Kim, Namhyun Kang

Mechanical and Materials Engineering Faculty Publications and Presentations

This study aimed to develop an artificial neural network (ANN) model for predicting the yield strength of a weld metal composed of austenitic stainless steel and compare its performance with that of conventional multiple regression and machine learning models. The input parameters included the chemical composition of the nine effective elements (C, Si, Mn, P, S, Ni, Cr, Mo, and Cu) and the heat input per unit length. The ANN model (comprising five nodes in one hidden layer), which was constructed and trained using 60 data points, yielded an R² value of 0.94 and a mean average percent error …

Combinatorial Studies Of Noble Metal Catalysts For Carbon Utilization, Natalie Leong Page

Theses and Dissertations

Electrocatalysts demonstrate significant promise for sustainable processes like carbon capture and generating recycled carbon fuels which are needed to achieve net zero carbon emissions. However, the commercialization of these processes is limited by several factors, one of which is the high cost of catalysts. The discovery and development of cheaper alternatives has been difficult due to constraints in experimental methodologies, scalability limitations, and a lack of understanding of reaction mechanisms. Within this dissertation is the development of a novel scanning electrochemical system and its implementation for high-throughput data generation from combinatorially sputtered material libraries. Combinatorial Pd-Au alloys were investigated for …

A Computational Investigation Of Wood Selection For Acoustic Guitar, Jonah Osterhus

Senior Honors Theses

The acoustic guitar is a stringed instrument, often made of wood, that transduces vibrational energy of steel strings into coupled vibrations of the wood and acoustic pressure waves in the air. Variations in wood selection and instrument geometry have been shown to affect the timbre of the acoustic guitar. Computational methods were utilized to investigate the impact of material properties on acoustic performance. Sitka spruce was deemed the most suitable wood for guitar soundboards due to its acoustic characteristics, strength, and uniform aesthetic. Mahogany was deemed to be the best wood for the back and sides of the guitar body …

Influence Of Al2o3 Passivation Layer Thickness On The Thermal Stability And Quality Of Mocvd-Grown Gan On Si, S M Atiqur Rahman, Manika Tun Nafisa, Zhe Chuan Feng, Benjamin Klein, Ian T. Ferguson

Symposium of Student Scholars

This research delves into the significant impact of varying thicknesses of the Al₂O₃ passivation layer on the thermal stability and crystalline quality of GaN on Si structures, an essential aspect for the next generation of high-temperature electronic and optoelectronic devices. By adopting metal-organic chemical vapor deposition (MOCVD) for the growth process, we analyzed structures with different Al₂O₃ passivation layer thicknesses: none, 2 nm, 10 nm, and 20 nm, each built upon the GaN layer. Through Raman spectroscopy, we meticulously assessed the changes in the E₂ (High) phonon mode's peak position and full width …

Effects Of Ti Addition On The Characteristics Of Al-10zn-6mg-2si/Zro2 Composites Produced By Squeeze Casting, Qesha Diva Prameshvara, Pipin Indah Lestari, Bondan Tiara Sofyan

Journal of Materials Exploration and Findings

Metal matrix composite (MMC) with 7xxx aluminum matrix is potential for ballistic applications due to the combination of strength, toughness, and light weight. Previous study successfully produced aluminum-based composites with SiC particles which were able to stop type III bullet, however cracks remained on back of the plate. Therefore, in this research, SiC was replaced by zirconia (ZrO₂) due to its high fracture toughness. Ti-B grain refiner was added to further improve toughness through grain boundary strengthening mechanism. This research developed 5 vol.% ZrO₂ strengthened Al-10Zn-6Mg-2Si composite with addition of Al-5Ti-1B grain refiner produced through squeeze casting …