Materials Science and Engineering Commons^™

Additive Manufacturing Of Sensors For Extreme Environments, Kiyo Tiffany Fujimoto

Boise State University Theses and Dissertations

Advanced manufacturing based direct-write technologies have emerged as the predominant enabler for the fabrication of active and passive sensors for use in harsh operating environments. The ability to directly write and integrate electronic components onto physical packaging can be achieved with additive manufacturing (AM) methods such as direct write technologies (DWT) which include aerosol jet printing (AJP), Ink Jet Printing (IJP), Plasma Jet Printing (PJP), and Micro-Dispense Printing (MDP). In this work, we investigate the use of these methods to accelerate, modernize, and enhance the functionality of sensors and instrumentation to achieve the goal of improving the safety and efficiency …

Electrochemical Impedance Spectroscopy Of Zirconium Oxidation For In-Situ Nuclear Sensing Applications, Michael Andrew Reynolds

Boise State University Theses and Dissertations

To meet the ever-growing energy demands of the modern world, alternative forms of producing power are necessary, and the field of nuclear engineering holds promise to answer this call. Nuclear fuel cladding in light water reactors (LWRs) currently draws a large amount of attention from scientists and researchers, as it provides many challenges to design around. Since the 1950s, zirconium and its protective oxide layer have been utilized as an effective material for the task, possessing good mechanical strengths, high corrosion resistance, and a low neutron absorption cross section. Despite these beneficial properties, however, fuel cladding remains vulnerable to several …

Towards Improving The Properties And Furthering Acceptance Of Advanced Technology Nuclear Fuels, Jennifer K. Watkins

Boise State University Theses and Dissertations

To avoid detrimental environmental impacts from climate change, the world community needs to push for the use of clean energy technologies. Development of proposed advanced technology nuclear fuels supports efforts to ensure nuclear energy is included as a non-carbon emitting source of electricity generation. Advanced technology nuclear fuels, also referred to as accident tolerant fuels (ATFs), have received renewed interest for use in the current nuclear reactor fleet as well as in advanced reactor technologies due to their high uranium loading, desirable thermophysical properties, and performance under irradiation as compared to the benchmark oxide fuel. A limiting consideration for the …

Multiphase Layered Transition Metal Oxide Positive Electrodes For Sodium Ion Batteries, Eric Gabriel, Dewen Hou, Eungje Lee, Hui Xiong

Materials Science and Engineering Faculty Publications and Presentations

Multiphase layered transition metal oxides (LTMOs) for sodium ion battery (SIB) positive electrodes with phase interfaces across multiple length scales are a promising avenue toward practical, high-performance SIBs. Combinations of phases can complement each other's strengths and mitigate their weaknesses if their interfaces are carefully controlled. Intra- and interparticle phase interactions from nanoscale to macroscale must be carefully tuned to generate distinct effects on properties and performance. An informed design strategy must be paired with relevant synthesis techniques and complemented by spatially resolved characterization tools to manipulate different length scales and interfaces. This review examines the design, synthesis, and characterization …

Synthesis And Molecular Processes Governing Self-Healing Polymeric Materials, Siyang Wang

All Dissertations

Self-healing polymers capable of recovering from physical damages are promising materials for advanced technologies. In these studies, we developed routes to achieve self-healable properties in acrylic-based copolymers that rely on non-covalent dipolar interactions present in essentially all polymeric materials. Using a combination of spectroscopic tools, thermo-mechanical analysis, and molecular dynamic (MD) simulations, these studies have shown that dipolar interactions lead to conformational changes of macromolecular segments which, in turn, result in self-healing without external intervention. This dissertation also describes the development of novel self-healable acrylic-based covalent adaptable networks (CANs) that combine reprocessing and self-healing properties. The utilization of dipolar interactions …

Synthesis And Phase Transition Characterization Of Liquid Crystal Membranes With Slit-Like Pores, Isaac Hopwood

Chemical Engineering Undergraduate Honors Theses

Membranes with slit-like pores have been of interest for some time due to their ability to reject smaller particles than traditional cylindrical-pored membranes at the same fluid flux. However, using liquid crystals as a template for this sort of membrane has not been thoroughly investigated. In this study, the liquid crystal mixture of RM257 (2-Methyl-1,4-phenylene bis(4-(3-(acryloyloxy)propoxy)benzoate)) and 5CB (4-Cyano-4'-pentylbiphenyl) for the purpose of manufacturing membranes with slit-like pores, the phase transition behavior of this LC mixture at various mole fractions of RM257, and the impact of mole fraction of RM257 in the liquid crystal (LC) mixture and membrane manufacturing conditions …

Evaluating The Effects Of Curing Methods On Bcsa Cement Concrete, Hannah Allen

Civil Engineering Undergraduate Honors Theses

BCSA cement is a type of cement that makes concrete set up much quicker than typical portland cement concrete. BCSA cement concrete also has a much higher compressive strength than that of portland cement concrete. This study was conducted to determine the effect of different curing conditions on the compressive strength of BCSA cement concrete.

Development Of Porous Solid Acid Catalysts For Lignocellulose And Plastic Upcycling., Mohammad Shahinur Rahaman

Electronic Theses and Dissertations

My goal is to develop chemical processes for transforming waste to solve environmental problems and enhance sustainability. Environmental problems such as pollution and massive amounts of waste are the main drivers that stimulate my research ideas. I focused on creating novel, efficient catalytic processes for converting polymeric waste "feedstocks" into high-value chemicals by integrating my expertise in catalysis, materials science, and synthetic chemistry to develop porous solid catalytic materials. During my Ph.D., I focused on two polymeric feedstocks, lignocellulose, and discarded plastic.

Early in my Ph.D. journey, I focused on catalytic upcycling of lignocellulose. Lignocellulosic biomass is cost-effective, abundant, and …

Effects Of Sizing Agents On Mechanical Properties Of Carbon Fiber–Polymer Composites Via Fused Filament Fabrication Additive Manufacturing., Benjamin D. Mitchell

Electronic Theses and Dissertations

This study demonstrated the effects of changing the sizing agent parameter during the preparation of carbon fibers on the mechanical properties of composite made with acrylonitrile butadiene styrene (ABS) as the matrix material and carbon fibers as the fiber material. Three types of sizing agents produced by Allnex were used to coat three different batches of carbon fibers that were mixed with a torque rheometer and extruded with a barrel-style melt extruder into continuous spools of 1.75 mm filament for use with commercial 3D printers. Tensile tests were conducted on the filaments and tensile bars printed from the materials. Results …

Extractive Membranes For The Detection And Screening Of Waterborne Plutonium, James Foster

All Dissertations

The development of rapid screening tools for special nuclear materials remains a crucial focus for nonproliferation efforts. Traditional approaches for the analysis of trace-level Pu isotopes in water requires tedious and time-consuming sample preparation steps that do not lend well to expeditious screening. Therefore, a novel analytical method that combines both Pu concentration and source preparation into a single detection system would make for an invaluable tool for nuclear security applications. Extractive membranes absorbers can help to fulfill this role as they are capable of concentrating Pu to detectable limits while subsequently serving as alpha spectrometry sample sources. In Chapter …

Sustainable Composites From Agricultural And Petroleum Waste, Menisha S. Karunarathna

All Dissertations

Green gas emission has been a pervasive and persistent subject of debate for a prolonged period. The soaring number of industries and vehicle fuel emissions presage a concomitant rise in global CO₂ emissions. Global cement production is responsible for 8% of the total CO₂ release, yet, the production continues due to the surging demand. Hence, there is an ongoing quest to find alternatives for cement and building materials produced with zero to lower CO₂ emissions. The work presented in this dissertation focuses on finding recyclable, zero CO₂ gas-producing high sulfur biocomposites materials, which can compete with …

Graphene Oxide-Thermoplastic Nanocomposites: Fabrication And Properties, Seyedeh Mastooreh Seyedi Ghezghapan

All Dissertations

Polymer nanocomposites are used for a wide variety of applications. These nanocomposites can have a number of important characteristics depending on the nature of the nanomaterial, its size, volume fraction, its distribution, and interactions within the host polymer. Mechanical strength, thermal and electrical conductivity are some of these materials' most focused and studied features. Besides the positive influences of the reinforcements, nanomaterials also might have some adverse impacts on the polymer matrix. These issues could arise from the aggregation of the fillers and the poor interfacial interactions of the components. Several approaches are introduced to modify the nanofillers and enhance …

Solid-State Formation Mechanisms Of Core–Shell Microstructures In (Zr,Ta)B2 Ceramics, Anna N. Dorner, Frédéric Monteverde, William Fahrenholtz, Gregory E. Hilmas

Materials Science and Engineering Faculty Research & Creative Works

Transition metal diborides with core–shell microstructures have demonstrated excellent mechanical properties at elevated temperatures. Previous studies concluded that core–shell microstructures were formed by liquid-assisted mass transport mechanisms, but in this study, we propose a solid-state formation mechanism for core-shell microstructures in (Zr,Ta)B2 ceramics produced by reaction hot pressing and in ZrB2-TaB2 diffusion couples. Diffusion couple experiments demonstrated that core–shell microstructures developed as a result of Ta diffusion along ZrB2 grain boundaries, which occurred concurrently with lattice diffusion of Ta into ZrB2. These findings suggest that with optimization of batching and processing parameters, core–shell diboride materials may be formed through solid-state …

Mechanical Properties Of Fusion Welded Ceramics In The Sic-Zrb2 And Sic-Zrb2-Zrc Systems, Jecee D. Jarman, William Fahrenholtz, Greg Hilmas, Jeremy Lee Watts, Derek S. King

Materials Science and Engineering Faculty Research & Creative Works

Mechanical properties of welded SiC-ZrB2 and SiC-ZrB2-ZrC ceramics were measured up to 1700 °C. Commercial powders were hot pressed, machined into coupons, and preheated to 1600 °C before joining the ceramics using either tungsten inert gas welding or plasma arc welding. Toughness of the parent materials was 3–4 MPa*m1/2 which decreased after welding to 2–2.5 MPa*m1/2. Strength of the SiC-ZrB2-ZrC parent material was ~700 MPa at 25 °C, ~300 MPa at 1700 °C, and retained 40–60% of this strength once welded. Strength of the SiC-ZrB2 parent material was ~600 MPa at 25 °C and 1700 °C and retained 20–30% of …

Preparation Of Concrete Specimen For Internal Sulfate Attack Analysis Using Electron Backscatter Diffraction, R. Sharon Uwanyuze, Lucas Enright, Jiyao Zhang, Stefan Schafföner

Materials Science and Engineering Faculty Research & Creative Works

Concrete cores were obtained from houses in eastern Connecticut, USA, that had varying degrees of crumbling foundations and wall cracking. Electron backscatter diffraction (EBSD) was used simultaneously with energy dispersive X-ray spectroscopy to investigate the degradation of these samples. This combination allowed the precise correlation of elemental composition with mineral crystallography phase mapping. EBSD examination showed the presence of pyrrhotite, pyrite, and marcasite phases in some of the samples, whereas internal sulfate attack (ISA) is triggered by the release of sulfates through the oxidation of such iron sulfides. Secondary expansion products from ISA are associated with foundation cracking, wall bulging, …

Development Of High Conductivity Copper Coatings For Srf Cavity, Himal Pokhrel

Physics Theses & Dissertations

The development of metallic coatings with high purity and high thermal conductivity at cryogenic temperature could be very important for application to the superconducting radiofrequency (SRF) cavity technology. The deposition of such bulk coatings on the outer surface of a niobium cavity could result in higher heat conductance and mechanical stiffness, both of which are crucial for enhancing the cavity performance at a reduced cost.

Cold spray technology was used to deposit bulk coatings of pure copper and copper-tungsten alloys on the niobium substrate and the samples of size 2 mm × 2 mm cross section were cut and subjected …

Energy Science & Engineering: 10 Years Of Excellence, Yun Hang Hu

Michigan Tech Publications, Part 1

No abstract provided.

Diffusive Dynamics Of Biological Macromolecules In The Cytoplasm Of Live Bacteria, Asmaa Sadoon

Graduate Theses and Dissertations

Bacteria are small organisms that play important roles in our bodies and in maintaining our surrounding environment. However, bacterial infections are considered as one of the health diseases that threatens the lives of humans. Resistance of bacteria to antibiotics has made treating bacterial infections more challenging. With the emergence of many developed optical techniques, it has become possible to study various biological mechanisms of molecules inside these small organisms with high resolution and precise localization. In this research, single particle tracking photoactivation localization microscopy (sptPALM) technique was used to investigate the dynamics of fluorescent histonelike nucleoid-structuring proteins (H-NS) in live …

Design, Fabrication, And Characterization Of An Array Of Graphene Based Variable Capacitors, Millicent Nkirote Gikunda

Graduate Theses and Dissertations

Since it was first isolated and characterized in 2004, graphene has shown the potential for a technological revolution. This is due to its amazing physical properties such as high electrical conductivity, high thermal conductivity, and extreme flexibility. Freestanding graphene membranes naturally possesses an intrinsic rippled structure, and these ripples are in constant random motion even room temperatures. Occasionally, the ripples undergo spontaneous buckling (change of curvature from concave to convex and vice versa) and the potential energy associated with this is a double well potential. This movement of graphene is a potential source of vibrational energy.

In this dissertation, we …

A Study On Effect Of Manufacturing Parameters On Morphology Of A356 Aluminum Foam, Nikhil Nanabhau Mahajan

All Theses

Metal foams have shown an excellent promise for usage as multifunctional material concerning research & development in the last 20 years. They provide remarkable mechanical as well as physical properties being lightweight. Open-cell metal foams have already been used in sound and noise absorption. Open-cell metal foams are outstanding for use in heat exchangers, filters, and many more applications, while closed-cell foams show excellent characteristics in impact energy absorptions. Closed-cell metal foams have higher energy absorption than their solid parent metal as they convert most of the impact energy into deformation energy. Metal foams have been used as prominent safeguard …

Control Strategy For Solar Energy-Saving Lamps For Optimized Energy Utilization And Sustainability Of Operation Durability: Indonesia Case, Burhanuddin Halimi, Agus Purwadi, Nana Heryana

Makara Journal of Technology

To solve the electrification ratio issue, the Indonesian government has promoted the use of solar energy-saving lamps. This study proposes a control strategy that adopts current reference time-based profiling for solar energy-saving lamps. For optimal energy consumption, the current reference profile is determined according to users’ daily energy requirements. From the aspect of user comfort, a gradual step reference profile is also introduced to provide a subtle change in lighting intensity level. The proposed control strategy can minimize energy consumption and optimize the operation durability of the system. The concept is verified by simulating four scenarios, the results of which …

Mechanical Behavior Of Clay Soil Stabilized With Fly Ash And Bottom Ash, Soewignjo Agus Nugroho, Azra Zulnasari, Ferry Fatnanta, Andius Dasa Putra

Makara Journal of Technology

Soil is one of the most important aspects of an infrastructure given its functions of receiving and holding structural loads. However, not all soils have good physical and mechanical properties. To overcome those conditions, stabilization of the soil is practiced to meet the technical requirements. This study aims to determine the behavior of high plasticity clay stabilized with lime, fly ash, and bottom ash. These additives can be used as a stabilizing agent to increase soil strength. The percentage of additives varied from 5%–25% then mixed with clay and were tested through the (Unconfined Compression Strength (UCS) test. The UCS …

Enhancement Of Biogas Production Through Solid-State Anaerobic Co-Digestion Of Food Waste And Corn Cobs, Lukhi Mulia Shitophyta, Anisa Salsabila, Firanita Angraini Putri, Siti Jamilatun

Makara Journal of Technology

Although biogas has been primarily produced through liquid anaerobic digestion, this method leads to the floating and stratification of fibers and non-homogeneous mixing, which can reduce the biogas yield. Alternatively, biogas can be produced by the solid-state anaerobic digestion (SS-AD) of organic material with a high solid content, such as corn cobs. We investigated the co-digestion of food waste and corn cobs as a biomass feedstock for SS-AD in biogas production. We measured the effects of the total solid (TS) content, percentage of food waste, and reduction in volatile solids (VS), from which we determined its appropriate kinetic model. We …

Investigation On Electrochemical Processes Of P-Aminothiophenol On Gold Electrode Of Nanostructures, Hui-Yuan Peng, Jia-Zheng Wang, Jia Liu, Huan-Huan Yu, Jian-De Lin, De-Yin Wu, Zhong-Qun Tian

Journal of Electrochemistry

Electrochemical reactions on nanostructured noble electrodes have received much attention, however, the reaction mechanism and reaction kinetics are still difficult to be studied. Probe molecule can give an insight to the investigation of electrochemical reactions on noble electrodes with nanostructures. In this paper, the electrochemical process of p-aminothiophenol (PATP) adsorbed on the gold electrode was studied by electrochemical cyclic voltammetry and surface-enhanced Raman spectroscopy (SERS). Here, we used one-step sodium citrate reduction method (Frens method) to synthesize gold nanoparticles, which are used to construct the nanostructured gold electrode. The Raman electrolytic cell used was based on the traditional three-electrode electrolytic …

Study On Electrochemical Conversion Of Ammonium Sulfate To Ammonium Persulfate In Acetylpyrazine Wastewater, Yi-Jie Wang, Dong-Fang Niu, Xin-Sheng Zhang

Journal of Electrochemistry

Acetylpyrazine is an important spice and also plays important roles in biology, medicine and other fields. However, the wastewater containing ammonium persulfate, ferric ion (Fe³⁺), pyrazine, and a large amount of ammonium sulfate was produced during the production of acetylpyrazine. In this study, ammonium sulfate in acetylpyrazine wastewater was electrolytically converted into ammonium persulfate for economic benefits. Using platinum as an anode and graphite as a cathode, the influence factors of the electrolysis process (including the composition of the anolyte, the current density, the temperature, etc.) were firstly investigated without interference from other compositions. Under the optimal condition, …

Study On Electrodeposition Of Antimony In Choline Chloride-Ethylene Glycol Eutectic Solvent, Hao Wang, Xiao-Zhou Cao, Xiang-Xin Xue

Journal of Electrochemistry

Antimony is a chemically stable metal that has been widely used in industry, military and other fields. The use of electrodeposition to prepare antimony coating has the advantages of simple operation and low cost. The deep eutectic solvent (DES) is a eutectic mixture composed of a hydrogen bond donor and a hydrogen bond acceptor at a fixed molar ratio. It has the advantages of wide electrochemical window, high thermal stability, easy preparation, and low cost. Selecting DES as the electrolyte for electrodeposition can avoid the hydrogen evolution reaction of the aqueous system and the toxicity of ionic liquids. In recent …

Adjusting The Alloying Degree Of Pt3Zn To Improve Acid Oxygen Reduction Activity And Stability, Tian-En Zhang, Ya-Ni Yan, Jun-Ming Zhang, Xi-Ming Qu, Yan-Rong Li, Yan-Xia Jiang

Journal of Electrochemistry

Proton exchange membrane fuel cell (PEMFC) is a new type of energy device, a relatively excellent way to achieve carbon neutrality. However, due to the relatively slow reaction rate of oxygen reduction reaction (ORR) at the cathode, platinum (Pt) is the key material of the cathode catalyst. However, Pt is a kind of noble metal, and its high cost restricts the PEMFC commercialization process. At present, the main approach is to combine transition metals with Pt to prepare Pt-based alloys and to reduce the use of Pt. Pt-based alloys are excellent catalysts for ORR, improving both the activity and stability, …

Preparation Of Pt@Basrtio3 Nanostructure And Its Properties Towards Photoelectrochemical Ammonia Synthesis, Jing Zhang, Rui-Xia Guo, Jian-Jun Fu, Shi-Bin Yin, Pei-Kang Shen, Xin-Yi Zhang

Journal of Electrochemistry

Ammonia is an important industrial raw material and a potential green energy. Using renewable energy to convert nitrogen into ammonia under ambient condition is an attractive method. However, the development of efficient photoelectrochemical ammonia synthesis catalysts remains a challenge. Perovskite such as BaSrTiO₃ (BST) is a good photocatalytic material. However, BST is active under ultraviolet light and has a high recombination rate of photogenerated electron-hole pairs. By dispersing precious metals, it can effectively regulate the absorption of sunlight by BST. In this work, we used a two-step method to prepare BST. The H₂PtCl₆·6H₂O …

Multi-Scale Simulation Revealing The Decomposition Mechanism Of Electrolyte On Lithium Metal Electrode, Yan-Yan Zhang, Yue Liu, Yi-Ming Lu, Pei-Ping Yu, Wen-Xuan Du, Bing-Yun Ma, Miao Xie, Hao Yang, Tao Cheng

Journal of Electrochemistry

Lithium metal is considered as an ideal anode material for next-generation high energy density batteries with its high specific capacity and low electrode potential. However, the high activity of lithium metal can lead to a series of safety issues. For example, lithium metal will continuously react chemically with the electrolyte, forming unstable the solid electrolyte (SEI) films. In addition, lithium dendrites can be formed during cycling, which can puncture the SEI film and cause short circuits in the battery. These drawbacks greatly hinder the commercial application of lithium metal. To solve the above problems, it is important to understand the …

Effects Of Electrode Shape On Lithiation Process Of Lithium-Ion Battery Electrodes, Shi-Wei Sun, Jian-Jun Nie, Yi-Cheng Song

Journal of Electrochemistry

This paper studies the influence of electrode shape on the lithiation process of lithium ion batteries. Both experimental observation and numerical simulation are employed to investigate the competitive interaction between the diffusion of lithium ions in both solid and liquid phases and the lithium intercalation reaction at the electrode surface. Experimental cells were prepared with the anode and cathode being placed parallel, leaving the latter embracing the former. An experimental device based on CCD camera was set up for in situ observation of electrode lithiation. The lithiation levels of the graphite anodes were estimated according to the observed color profile. …