Materials Science and Engineering Commons^™

Development Of Eam And Rf-Meam Interatomic Potential For Zirconium Diboride, Bikash Timalsina

Graduate Theses/Dissertations

Embedded Atom Method (EAM) and Modified-EAM (MEAM) interatomic potentials were developed for zirconium diboride (ZrB₂). The EAM and “Reference Free” (RF) version of the Modified Embedded Atom Method (RFMEAM) potentials have been fitted by utilizing Density Functional Theory (DFT)-based datasets including lattice deformations and high-temperature ab-initio molecular dynamics (AIMD) simulation results. The occupancies of phonons for acoustic phonon modes from the density functional theory calculation shows that these modes of vibration, mostly due to heavier mass element (Zr), which occur below 8.711 THz, while a slight underestimation to that of DFT calculation predicted by EAM below 8.439 THz …

Camshaft Failure Simulation With Static Structural Approach, Riduwan Prasetya, Andoko Andoko, Suprayitno Suprayitno

Journal of Mechanical Engineering Science and Technology (JMEST)

A failure happens within the camshaft of the minibus when the vehicle is in utilize. The camshaft was a fracture within the bearing between the primary cylinder exhaust valve and the second cylinder suction. This simulation aims to find the causes of camshaft failure utilizing the finite element method with a static structural approach, including simulations of deformation, strain, stress, fatigue life (stress-life and strainlife), and cracks. The method used in this paper is the finite element method with a static structural approach by ANSYS software. The camshaft material is a gray cast iron designed using Solidworks. Pre-processing includes meshing …

Evaluating Storage And Effective Moduli Of In Situ Polymerised And Melt Extruded Pa6 Graphite (G) Composites, Muneer Umar, Michael Ikpi Ofem, Auwal Sani Anwar, Muhammad Murtala Usman

Journal of Mechanical Engineering Science and Technology (JMEST)

Four PA6/graphite (G) composites systems were made. Two using in situ polymerisation equivalent in mixing strain and two systems melt extrusion of equivalent processing strain. The effective modulus of the carbons, room temperature storage modulus and storage modulus at 80 ⁰C were evaluated. The composite/unfilled PA6 ratios at E25 and that at E80 for the in situ polymerised system IG 40/10 are 1.37 and 1.63, respectively. For the in situ polymerised system IG 20/20, the same were 1.96 and 2.28, respectively. For the melt-extruded systems, G 100/6 had the best E25 ratio of 1.67 and E80 of 2.03, whereas the …

The Effect Of Multi-Extrusion Process Of Polylactic Acid On Tensile Strength And Fracture Morphology Of Filament Product, Muhamad Syaifuddin, Heru Suryanto, Suprayitno Suprayitno

Journal of Mechanical Engineering Science and Technology (JMEST)

Polylactic acid (PLA) is one of the most used materials in FDM 3D Printing. Large-scale consumption of PLA on an industrial scale could cause environmental and efficiency problems. Thus, PLA waste and industry waste need to be recycled to limit excessive waste. This study aimed to investigate the change in mechanical property, morphology, and structure of mechanically recycled PLA. Recycling was performed 12 times using the extrusion process with an extrusion temperature nozzle of 170°C. The SEM, structural analysis, and amorphous-crystalline analysis used XRD. The results showed a gradual decrease of tensile strength from each recycle with a total of …

Electrochemical Corrosion Properties Of Ternary Al And Quaternary Zr Added Bell Metal In 0.1m Nacl Solution, Sakib Al Razi Khan, Mohammad Ashfaq Hossain, Maglub Al Nur, Mohammad Salim Kaiser

Journal of Mechanical Engineering Science and Technology (JMEST)

The electrochemical corrosion property of ternary Al and quaternary Zr added Bell metal in 0.1M Sodium Chloride solution has been experimentally conducted at room temperature. Electrochemical impedance spectroscopy (EIS) method and Potentiodynamic polarization technique are used to carry out the electrochemical investigation. Microhardness test is also conducted for all three alloys and it reveals that Al addition increases the hardness of bell metal due to the formation of different intermetallic precipitates of Cu and Al. Optical Micrograph as well as Scanning Electron Micrograph have also been studied to characterize their surface condition. It is found that Zr addition refines the …

The Effect Of Thickness And Type Of Material On The Sheared Edge Characteristics Of Keychain Cranioplasty Plate Blanking Product Using Eccentric Press Machine, Didin Zakariya Lubis, Lea Rachmat Indrasepta, Redyarsa Dharma Bintara, Rizky Ramadhan, Agung Budi Darmawan

Journal of Mechanical Engineering Science and Technology (JMEST)

Keychain cranioplasty plate product has the potential to be produced using the blanking process because it is faster, low-cost, and requires low-energy consumption compared to other mechanical operations. This research aimed to find the effect of material thickness and type on the sheared edge characteristics of keychain cranioplasty plate using the blanking process to meet the international health standard. Experimental research conducted using an eccentric press machine with 40 tons capacity. This research’s test material parameters of titanium (Ti-6AL-4V) and stainless steel (SS-316L) were the 0.5 mm, 0.6 mm, and 0.8 mm thickness with a maximum blanking velocity of 3000 …

Effect Of Dcrp And Dcsp Polarity On The Depth Of Penetration Of Smaw On Low Carbon Steel Astm A36 Using E7018 Electrode, Ma'mun Hidayat, Helleni Febnesia, Sulaeman Deni Ramdani

Journal of Mechanical Engineering Science and Technology (JMEST)

The study aims to determine the level of penetration depth using SMAW (Shielded Metal Arc Welding) Process based on the polarity type of DCRP (Direct Current Reverse Polarity) and DCSP (Direct Current Straight Polarity). This research used ASTM A36 low carbon steel plate with thickness of 6 mm and length of 200 mm, Electrode E7018 LB-52-18 ∅ 3.2 mm, and with current parameters of 90 A, 100 A, 110 A, 120 A and 130 A and 70 ° welding arc angle. The method used the experimental research. Data collection techniques applied direct observation techniques and descriptive statistical data analysis techniques. …

Fully Coupled Internal Radiative Heat Transfer For The 3d Material Response Of Heat Shield, Raghava S. C. Davuluri, Rui Fu, Kaveh A. Tagavi, Alexandre Martin

Mechanical Engineering Faculty Publications

The radiative transfer equation (RTE) is strongly coupled to the material response code KATS. A P-1 approximation model of RTE is used to account for radiation heat transfer within the material. First, the verification of the RTE model is performed by comparing the numerical and analytical solutions. Next, the coupling scheme is validated by comparing the temperature profiles of pure conduction and conduction coupled with radiative emission. The validation study is conducted on Marschall et al. cases (radiant heating, arc-jet heating, and space shuttle entry), 3D Block, 2D IsoQ sample, and Stardust Return Capsule. The validation results agree well for …

Degumming Of Hemp Fibers Using Combined Microwave Energy And Deep Eutectic Solvent, Bulbul Ahmed

LSU Master's Theses

Hemp is considered as one of the sustainable agricultural fiber materials. Degumming or surface modification of hemp bast is needed to produce single fibers for ensuing textile and industrial applications. The traditional degumming process necessitates a high amount of alkali, which causes detrimental environmental pollution. This study offers a new method to degum hemp fibers with reduced use of harmful alkali and precious water resources. In this work, hemp bast fibers were degummed by using combined microwave energy and deep eutectic solvent (DES). The properties of hemp fibers manufactured by this method were investigated and compared with the traditional alkali …

Semi Real-Time Detection Of Subsurface Consolidation Defects During Concrete Curing Stage, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Subsurface consolidation defect is a common issue in concrete pavement construction, and the hidden defects often require costly repairs after project delivery. Therefore, being able to identify this type of defect during construction will enable contractor to conduct quick repairs to avoid costly post-construction rework. In this paper a semi real-time detection approach using infrared thermography is introduced. The developed approach utilizes the hydration heat during curing time to identify the subsurface voids based on the regional temperature contrast. Experimental studies were conducted using artificial void-defect in different sizes and depths. The thermographic analysis is employed to locate the void-defects …

Reduced-Order Modeling Of Loosening In Bolted Joints And Dynamic Interactions Between Axially Aligned Threaded Joints, Sandro Aldana

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Maintaining effective preload in bolted joints is critical for ensuring long-term performance and safety throughout the operation of any assembled structure. The loosening of bolted joints has been studied since the Industrial Revolution, but modeling approaches have only emerged over the past three decades. Although existing approaches are capable of simulating or predicting loosening in a single joint consisting of a single bolt, they are too computationally expensive to be used to model loosening in large structures consisting of many bolts. The objective of this thesis is to construct and employ a reduced-order modeling (ROM) approach that treats the internal …

Thermal And Mechanical Analysis Of Bombyx Mori Silk Nanofibers, Justin Busnot

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

This thesis presents a study on the thermomechanical properties of Bombyx Mori silk nanofibers. These nanofibers were obtained from silkworm cocoons which were degummed to separate the fibroin and the sericin, the two proteins that make up silk. The fibroin was then centrifuged to remove insoluble particles and stored and 4°C before the electrospinning process. A parametric study of the electrospinning process was carried out in order to identify the factors allowing to obtain optimal mechanical properties. The current as well as the flow rate applied, the diameter of the syringe, the distance separating the syringe from collector or even …

High-Throughput Design Of High-Performance Lightweight High-Entropy Alloys, Rui Feng, Chuan Zhang, Michael C. Gao, Zongrui Pei, Fan Zhang, Yan Chen, Dong Ma, Ke An, Jonathan D. Poplawsky, Lizhi Ouyang, Yang Ren, Jeffrey A. Hawk, Michael Widom, Peter K. Liaw

Mathematical Sciences Faculty Research

Developing affordable and light high-temperature materials alternative to Ni-base superalloys has significantly increased the efforts in designing advanced ferritic superalloys. However, currently developed ferritic superalloys still exhibit low high-temperature strengths, which limits their usage. Here we use a CALPHAD-based high-throughput computational method to design light, strong, and low-cost high-entropy alloys for elevated-temperature applications. Through the high-throughput screening, precipitation-strengthened lightweight high-entropy alloys are discovered from thousands of initial compositions, which exhibit enhanced strengths compared to other counterparts at room and elevated temperatures. The experimental and theoretical understanding of both successful and failed cases in their strengthening mechanisms and order-disorder transitions further …

Mechanical Properties And Microstructure Characteristics Of Alloy Parts Produced By Laser Powder Bed Fusion (Lpbf) Method, Hong Yao

LSU Doctoral Dissertations

Additive manufacturing (AM) is a rapid prototyping technology to produce fully functional and complex designing objects. As one of the AM methods, Laser Powder Bed Fusion (LPBF) has gained the most attention from both academic researchers and industrial companies. During the LPBF process, metal powders are applied layer by layer, which can be 20 microns to 50 microns in thickness. After a layer is prepared, a high-power laser, which is commonly controlled by a scanning head, is used to selectively melt the interested area of a 2D geometry which is designed in a computer aided designing software. LPBF method can …

Optimization Of Load-Bearing And Impact Energy Absorption Capacities Of Honeycomb Structures By Density Gradation, Oyindamola Khadijat Rahman

Theses and Dissertations

Density gradation has been analytically and experimentally proven to enhance the load-bearing and energy absorption efficiency of cellular solids. This research focuses on the analytical optimization (by virtual experiments) of polymeric honeycomb structures made from flexible thermoplastics to achieve density-graded structures with desired mechanical properties. The global stress-strain curves of single-density honeycomb structures are used as input to an analytical model that enables the characterization of the constitutive response of density-graded hexagonal honeycombs with discrete and continuous gradations and for various gradients. The stress-strain outputs are used to calculate the specific energy absorption, efficiency, and ideality metrics for all density-graded …

Preparation And Characterization Of Single Layer Conducting Polymer Electrochromic And Touchchromic Devices, Sharan Kumar Indrakar

USF Tampa Graduate Theses and Dissertations

Electrochromic devices (ECDs) have triggered great interest because of their potential applicability in energy-efficient buildings and low power display systems, including reflective type smart windows/mirrors and wearable-flexible devices. In the past decades, electrochromic technologies with different device structures and materials have been proposed. The idea of employing a simple device structure with a durable, cost effective electrolyte is crucial to designing and manufacturing high-performance ECDs. With this idea in mind, this thesis describes the various efforts to develop a simple ECD comprising of a composite single active layer gel electrolyte, sandwiched between two transparent conducting electrodes, lasting over 10,000 cycles …

An Investigation On Formability And Crystallographic Texture In Novel Magnesium Alloys, Pnina Ari-Gur, Andreas Quojo Quainoo, Shubram Subramanyam, Ashkan Razania, Sven Vogel, Wei Gao

Mechanical and Aerospace Engineering Faculty Publications

Magnesium alloys offer many advantages. They offer very low density and good strength. They also offer good damping properties. One of the industries where reducing component weight is the automotive industry. That makes the magnesium alloys good candidates for these applications. Reduced weight of an automobile means also lower fuel consumption. The hexagonal closed packed structure of magnesium, lends itself to strong mechanical anisotropy. In the current work, neutron diffraction was used to study the crystallographic texture developed in novel magnesium alloys during cold rolling operations. The texture was compared with that developed in the commercial AZ-31 magnesium alloy. Tests …

Frequency Effect On Peak Pressure Coefficients Using The Narrowband Synthesis Random Flow Generator (Nsrfg) Method, Zayuris Del Carmen Atencio Mojica

Graduate Theses and Dissertations

The collapse of the Tacoma Narrows Bridge in Washington state in 1940 due to high wind forces gave structural engineers notice of the importance of understanding the behavior of wind forces on infrastructure. Wind forces play an important role in the design of buildings and other structures. ASCE 7-16 is the manual used for the design of these buildings and other structures throughout the country. These design criteria have been approved based on research projects involving experimental procedures. For the design of wind loads, ASCE 7-16 uses criteria based on wind tunnel (WT) tests. However, since the development of computing …

Tribological Studies Of Thick Polytetrafluoroethylene Coatings Enhanced By Polydopamine And Nanoparticles, Sujan Kumar Ghosh

Graduate Theses and Dissertations

Polytetrafluoroethylene (PTFE) is a popular low friction solid lubricant with high chemical and thermal stability. Thick PTFE coatings have the potential for many tribological applications, such as replacing Tin-based Babbitt materials in journal bearings. However, the weak bonding strength to the substrate and the high wear rate of PTFE coatings are current limiting factors. The lack of understanding of their tribological properties and wear mechanisms in oil-lubricated conditions and how coating thickness affects the tribological performance further hindered the use of PTFE coatings. In this dissertation, polydopamine (PDA), a bio-inspired adhesive, is used as an underlayer for or as a …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Review: Factors Affecting Composite Laminates Against Lightning Strikes, Aaryan Manoj Nair

Publications and Research

Lightning strike protection (LSP) have recently been a newly developing field particularly with the emergence of graphene thin film integration into carbon fiber composite structures. This technology has a widespread application in airplanes, wind turbines, and other instruments which are susceptible to frequent lightning strikes. Electrical discharge of the instrument in a safe manner is vital for the safety of the passengers (in the case of flights) as well as the integrity of the aircraft structures because of their specific mechanical and structural properties, which are essential for their functioning. The purpose of the study is to fabricate graphene thin …

Anisotropic Plasticity Modeling Of Thin Sheets And Its Application To Micro Channel Forming Of Steel Foils, Jie Sheng

Mechanical Engineering Research Theses and Dissertations

Thin sheet metals and ultrathin metal foils produced by industrial rolling processes are textured polycrystalline materials and their mechanical behaviors may depend strongly on the orientation of applied loading. Consideration of such plastic anisotropy in advanced modeling of these materials is of the paramount importance in designing optimal manufacturing processes for automotive and other applications using finite element methods. This research addresses several critical issues in anisotropic plasticity modeling and its applications in analyzing micro channel forming of ultrathin stainless-steel foils. An experimental study has first been carried out on the accuracy and sensitivity of measuring the plastic strain ratios …

Optimization Of 3d Printed Mold Performance For Injection Molding Via Hollow Infill Patterns, Alan Fong

University Honors Theses

The applicability of hollow infill patterns has been explored for its applications in making 3D printed polymer-based injection molds in the additive manufacturing industry. Hollow infill patterns offer a significant reduction in material costs as well as the opportunity for reducing the cooling times via pumping a coolant fluid through the hollow cavity in a similar fashion to traditional conformal cooling channels. A 3D Jacks Support Hollow mold model was determined to be the best performing design. FEA analysis was conducted to determine the maximum reduction in internal volume (percentage of material saved) that could be achieved without exceeding the …

The Development Of Novel Carbohydrate-Based Gelators And Their Applications As Advanced Soft Materials, Joedian Morris

Chemistry & Biochemistry Theses & Dissertations

Low molecular weight gelators (LMWGs) are attractive molecules that have been explored extensively due to their practical applications in many disciplines. These small molecules self-assemble forming solid-like gels via three-dimensional cross-linked networks with the solvent as the key component within the matrix. Carbohydrate-based LMWGs are small molecules that can form solid-like gels in water, organic solvents, and aqueous solutions. They have great potential to be utilized in different applications because carbohydrates are biocompatible and can be made from easily accessible and renewable resources. Designing gelators is still a challenge within the field, even though researchers have developed tools to predict …

Direct Torque Control For Silicon Carbide Motor Drives, Mohammad Hazzaz Mahmud

Graduate Theses and Dissertations

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives.

To overcome …

Decoupling The Effects Of Interfacial Chemistry And Grain Size In Perovskite Stability, Mirra M. Rasmussen, Kyle M. Crowley, Miranda S. Gottlieb, Geneviève Sauvé, Ina T. Martin

Student Scholarship

No abstract provided.

Surface Energy And Microstructure: The Effect Of The Underlying Substrate On Perovskite Film Formation For Solar Cell Absorbers, Mirra M. Rasmussen, Kyle M. Crowley, Ina T. Martin

Student Scholarship

No abstract provided.

A Computational Study Of Radiation Damage In Bilayer Silicon-Gold Structures, Cameron Hopper

Graduate Theses and Dissertations

Irradiation from sources such as nuclear reactors bombard materials with neutrons and heavy ions. The primary consequence of this irradiation is the displacement of atoms from their atomic structure. As the structure becomes damaged, the mechanical properties can change. Eventually, this can result in a failure due to embrittlement. This type of damage is hard to detect and can result in sudden, unexpected failure. Therefore, focusing on managing the consequences of irradiation has been a heavily researched topic. To manage irradiation, the focus is primarily to manage the voids and interstitials that appear during irradiation. Grain boundaries and amorphous regions …

Fabrication And Characterization Of Photodetector Devices Based On Nanostructured Materials: Graphene And Colloidal Nanocrystals, Wafaa Gebril

Graduate Theses and Dissertations

Photodetectors are devices that capture light signals and convert them into electrical signals. High performance photodetectors are in demand in a variety of applications, such as optical communication, security, and environmental monitoring. Among many appealing nanomaterials for novel photodetection devices, graphene and semiconductor colloidal nanocrystals are promising candidates because of their desirable and unique properties compared to conventional materials.

Photodetector devices based on different types of nanostructured materials including graphene and colloidal nanocrystals were investigated. First, graphene layers were mechanically exfoliated and characterized for device fabrication. Self-powered few layers graphene phototransistors were studied. At zero drain voltage bias and room …

Electrochemical Deposition In Energy Storage Devices, Witness Atutala Martin

Graduate Theses and Dissertations

Metals, whether in a solid or soluble ion form, are a vital part of any electrochemical storage system. More so, Li metal is widely considered as the ideal anode because of its low density and low electrochemical potential (-3.04 V vs. the standard hydrogen electrode – SHE). However, just like most metals, it does not plate or strip evenly during cycling which can lead to cycling performance issues, short cycling lifespans, and even safety concerns brought about by dendrites that can cause internal short-circuiting within cells. This research focused on investigating the electroplating of metals in both aqueous and non-aqueous …