Materials Science and Engineering Commons^™

Synthesis Of Radioactive Nanostructures In A Research Nuclear Reactor, Maria Camila Garcia Toro

Masters Theses

In this work, the synthesis of radioactive nanostructures by water radiolysis was studied. The irradiation processes were done in the Missouri University of Science and Technology research nuclear reactor (MSTR).

Radioactive gold nanoparticles (AuNPs) were synthesized from aqueous solutions containing the metal salt precursors by radiolysis of water. Seven different samples were irradiated at 200kW of thermal power for 0.5, 1, 3, 5, 10, 30, and 60 minutes. The average sizes of the obtained nanoparticles ranged from 3 nm to 400 nm, it was found that the particle size decreased with the irradiation time. Some agglomerations of particles were found …

Processing Of Al-12si-Tnm Composites By Selective Laser Melting And Evaluation Of Compressive And Wear Properties, Konda Prashanth, Sergio Scudino, Anil Chaubey, Lukas Löber, Pei Wang, Hooyar Attar, Frank Schimansky, Florian Pyczak, Jürgen Eckert

Research outputs 2014 to 2021

Al-12Si (80 vol%)-Ti52.4Al42.2Nb4.4Mo0.9B0.06 (at.%) (TNM) composites were successfully produced by the selective laser melting (SLM). Detailed structural and microstructural analysis shows the formation of the Al6MoTi intermetallic phase due to the reaction of the TNM reinforcement with the Al-12Si matrix during SLM. Compression tests reveal that the composites exhibit significantly improved properties (∼140 and ∼160 MPa higher yield and ultimate compressive strengths, respectively) compared with the Al-12Si matrix. However, the samples break at ∼6% total strain under compression, thus showing a reduced plasticity of the composites. Sliding wear tests were carried out for both the Al-12Si matrix and the Al-12Si-TNM …

Beyond Conventional C-Plane Gan-Based Light Emitting Diodes: A Systematic Exploration Of Leds On Semi-Polar Orientations, Morteza Monavarian

Theses and Dissertations

Despite enormous efforts and investments, the efficiency of InGaN-based green and yellow-green light emitters remains relatively low, and that limits progress in developing full color display, laser diodes, and bright light sources for general lighting. The low efficiency of light emitting devices in the green-to-yellow spectral range, also known as the “Green Gap”, is considered a global concern in the LED industry. The polar c-plane orientation of GaN, which is the mainstay in the LED industry, suffers from polarization-induced separation of electrons and hole wavefunctions (also known as the “quantum confined Stark effect”) and low indium incorporation efficiency that …

The Modification Of Silica Aerogel Materials For Contemporary Use, Lauren White

Theses and Dissertations

Aerogel materials have had limited utility due to their fragility, geometrical limitations, fabrication costs and protracted fabrication times. The objective of this project was to eliminate these limitations. Native, cross-linked and hybrid aerogel monoliths have been fabricated using a newly developed one-pot method without the need for solvent exchange. The key to this technique is the use of an ethanol–water azeotrope mixture, which contains 4.4% water by volume, as both a gelation and supercritical drying solvent. The small water content allows for drying at temperatures close to the supercritical temperature of the dry solvent, where reactions such as silica dissolution …

Diagnostics And Degradation Investigations Of Li-Ion Battery Electrodes Using Single Nanowire Electrochemical Cells, Naveen Kumar Reddy Palapati, Naveen Kumar Reddy Palapati

Theses and Dissertations

Portable energy storage devices, which drive advanced technological devices, are improving the productivity and quality of our everyday lives. In order to meet the growing needs for energy storage in transportation applications, the current lithium-ion (Li-ion) battery technology requires new electrode materials with performance improvements in multiple aspects: (1) energy and power densities, (2) safety, and (3) performance lifetime. While a number of interesting nanomaterials have been synthesized in recent years with promising performance, accurate capabilities to probe the intrinsic performance of these high-performance materials within a battery environment are lacking. Most studies on electrode nanomaterials have so far used …

Effects Of Antidepressants On Human Mesenchymal Stem Cell Differentiation On Clinically Relevant Titanium Surfaces, Nancy B. Ayad

Theses and Dissertations

Selective Serotonin Reuptake Inhibitors (SSRIs) are the most frequently prescribed class of drugs worldwide and are implemented in the treatment of depression and other psychiatric disorders. SSRIs relieve depressive symptoms by modulating levels of the neurotransmitter serotonin in the brain. SSRIs block the function of the serotonin transporter, thereby increasing concentrations of extracellular serotonin. However, serotonin levels in the neurons of the brain only account for 5% while the remaining 95% is present outside the brain. Serotonin receptors and transporter are located on bone resident cells (mesenchymal stem cells (MSCs)), osteoblasts and osteoclasts, and serotonergic activity is believed to affect …

Corn Stover Biochar In Gypsum Board: Empirical Analysis Of Thermal Conductivity And Flexural Strength, Albena Yordanova

Dissertations and Theses @ UNI

Gypsum board, an economical and durable finish material for wall and ceiling construction in the United States and worldwide, is the component with the lowest thermal performance in a typical exterior wall assembly. It also constitutes a substantial portion of construction waste in landfills, potentially creating harmful environmental effects and dangerous gases. To minimize the negative effects of fast growing construction waste of gypsum in landfills and meet higher standards for energy efficiency in construction, there is a need to explore sustainable ways of improving thermal properties of gypsum board and recycling the material. Gypsum can be recycled and used …

Benchmark Dose Modeling With Covariates For Nanomaterials, Sarah E. Davidson

Mathematics

In the last decade, the use of engineered nanomaterials (ENMs) such as titanium dioxide (TiO2), carbon nanotubes (CNTs), carbon nanofibers (CNFs), as well as a variety of other materials have become increasingly popular in commerce because of their many beneficial properties (e.g. ability to manufacture products that are lighter, stronger, and/or more compact). However, according to the National Institute of Occupational Safety and Health, with the development of new nanotechnology it is prudent to ensure the health and safety of workers who are producing or using these materials at the forefront. For many ENMs, occupational exposure limits (OELs) are not …

Development Of Implants Composed Of Bioactive Materials For Bone Repair, Wei Xiao

Doctoral Dissertations

"The purpose of this Ph.D. research was to address the clinical need for synthetic bioactive materials to heal defects in non-loaded and loaded bone. Hollow hydroxyapatite (HA) microspheres created in a previous study were evaluated as a carrier for controlled release of bone morphogenetic protein-2 (BMP2) in bone regeneration. New bone formation in rat calvarial defects implanted with BMP2-loaded microspheres (43%) was significantly higher than microspheres without BMP2 (17%) at 6 weeks postimplantation. Then hollow HA microspheres with a carbonate-substituted composition were prepared to improve their resorption rate. Hollow HA microspheres with ~12 wt. % of carbonate showed significantly higher …

Phase Field Modeling Of Electrodeposition Process In Lithium Metal Batteries, Nihal Acharya

Masters Theses

"One of the main weaknesses in long term performance of conventional lithium batteries is the growth of lithium microstructures on the electrode surface due to an electrochemical process, which can eventually lead to failure of these batteries. Suppressing this microstructure growth is a key in developing new generations of lithium metal batteries (LMBs). In this study, a two-dimensional (2D) phase field model is constructed to understand and determine the parameters controlling formation and evolution of microstructures in LMBs. A Ginzburg-Landau free energy functional, which is a function of concentration of Li⁺ and applied voltage, and a system consisting of …

Material Properties Affecting The Penetration Of Metal Targets By Copper Linear Shaped Charges, Kevin Lee Phelps

Masters Theses

"A linear shaped charge (LSC) is an explosive device used in demolition, aerospace, and in other applications that require the cutting of metal. Users of LSC's typically know the size of shaped charge needed to cut their target but commonly encounter previously untested materials. The motivation for this thesis is to provide an understanding as to what target material properties are good indicators of cutting performance so the selection of LSC can be more efficient. The author found that penetration theories for other types shaped charges were insufficient for the LSC, possibly because of the relatively slow projectile created by …

Thermal Characterization Of Phase Change Materials For Thermal Energy Storage, Rami Mohammad Reda Saeed

Masters Theses

"The study provides a valuable and useful database for Phase Change Materials (PCMs) for Thermal Energy Storage (TES) applications. Only a few existing studies have provided an overall investigation of thermophysical properties of PCMs in this detailed manner. Several organic PCMs, namely Myristic acid, Capric Acid, Lauryl Alcohol, Palmitic acid and Lauric acid, have been characterized after being carefully selected to cover wide range of TES applications. Insights and information gained from this work will be applied toward the design and modelling of many low temperature thermal energy storage applications. The study experimentally investigated uncertainty of thermal characterization of PCMs …

A Study On Non-Metallic Inclusions In Foundry Steel Process, Marc Leonard Harris

Masters Theses

"The effects of sample area and automated SEM/EDS feature analysis parameters (step size, magnification and threshold) on nonmetallic inclusion characterization results has been investigated and optimized. A post-processing program was developed to automatically determine average inclusion chemistry, total element concentrations within inclusions, and for generating joint ternary diagrams with size visualization for representing nonmetallic inclusion populations. Using these tools the evolution of nonmetallic inclusions was examined for 4320 steel at a participating industrial steel foundry. The steel was sampled throughout electric arc furnace melting through ladle refining to the final casting where an in-mold sampling procedure was developed to procure …

Hybrid Manufacturing Processes For Fusion Welding And Friction Stir Welding Of Aerospace Grade Aluminum Alloys, Megan Alexandra Gegesky

Masters Theses

"Friction stir welding and processing can provide for joints in aerospace grade aluminum alloys that have preferable material properties as compared to fusion welding techniques. Aerospace grade aluminum alloys such as AA2024-T3 and AA7075-T6 are considered non-weldable by traditional fusion welding techniques. Improved mechanical properties over previously used techniques are usually preferable for aerospace applications. Therefore, by combining traditional fusion welding and friction stir processing techniques, it could be plausible to create more difficult geometries in manufactured parts instead of using traditional techniques. While this combination of fusion welding and friction stir processing is not a new technology, its introduction …

Carbon Transfer From Magnesia-Graphite Ladle Refractories To Ultra-Low Carbon Steel, Andrew Arthur Russo

Masters Theses

"Ultra-low carbon steels are utilized in processes which require maximum ductility. Increases in interstitial carbon lower the ductility of steel; therefore, it is important to examine possible sources of carbon. The refractory ladle lining is one such source. Ladle refractories often contain graphite for its desirable thermal shock and slag corrosion resistance. This graphite is a possible source of carbon increase in ultra-low carbon steels. The goal of this research is to understand and evaluate the mechanisms by which carbon transfers to ultra-low carbon steel from magnesia-graphite ladle refractory.

Laboratory dip tests were performed in a vacuum induction furnace under …

Computational Fluid Dynamics (Cfd) Simulations Of Molten Steel Flow Patterns And Particle-Wall Adhesion In Continuous Casting Of Steels, Mahdi Mohammadi-Ghaleni

Masters Theses

"In this research, the measurements of clog deposit thickness on the interior surfaces of a continuous casting nozzle were compared with Computational Fluid Dynamics (CFD) predictions of melt flow patterns and particle-wall interactions to identify the mechanisms of nozzle clogging. A hybrid turbulent approach, Detached Eddy Simulation (DES), was configured to simulate both turbulent structures and particle-wall interactions inside the nozzle accurately. For experimental measurements of nozzle clogging, a nozzle received from industry was encased in epoxy and carefully sectioned to allow measurement of the deposit thickness on the internal surfaces of the nozzle. CFD simulations of melt flow patterns …

Synthesis And Photonic Sintering Of Bioresorbable Zinc Nanoparticle Ink For Transient Electronics Manufacturing, Bikram K. Mahajan

Masters Theses

"Zinc is an essential 'trace element' that supports immune systems, and is required for DNA synthesis, cell division, and protein synthesis. Zinc nanoparticles (Zn NP) has antibacterial properties and potential to be used in biodegradable printed electronics devices. The research presented here is about the synthesis of Zn NP and their potential use in transient electronics devices. In Paper 1, a technique of room temperature synthesis of Zn NP is reported using ball milling. Controlled amount of PVP was mixed in the solvent to stabilize the Zn particles and minimize cold welding during milling. The size of the produced Zn …

Biodegradable Electronic And Optical Devices Toward Temporary Implants, Md Shihab Adnan

Masters Theses

"Implantable biomedical devices have a high potential to revolutionize health care technologies in near future. Implantable devices can be classified as permanent prosthetic devices such as pacemakers or nerve stimulants and temporary devices for intermediate monitoring and control scenario which are still in research phase. In contrast to permanent device, temporary implants lose functionality and become unnecessary after intended operational lifetime which may pose serious electromagnetic and biomedical safety concern, latent complications at the implanted sites and possible ethical issues if not removed from body by an additional surgical operation.

The first paper of this thesis focuses on exploring the …

Nd2fe14b: (Nd1-X Dyx)2 Fe14b Core-Shell Structure Formation By Hot Press Liquid Phase Sintering, Li Chen

Dissertations, Master's Theses and Master's Reports

The purpose of this project is to produce Nd rich core-Dy rich shell grain structure in liquid phase sintered alloys by consolidating Dy rich powder mixed with powder. The technical barrier to producing the core-shell microstructure is that the Dy composition variations will homogenize during the consolidation process. This dissertation is based on the hypothesis that compositional homogenization of the core-shell structure can be minimized if consolidation occurs under applied pressure (hot press liquid phase sintering). The hypothesis is tested by comparing the homogenization of the Dy composition to the degree of consolidation with and without applied pressure. It is …

Investigation Of The Resistance To Demagnetization In Bulk Rare-Earth Magnets Comprised Of Crystallographically-Aligned, Single-Domain Crystallites With Modified Intergranular Phase, Jie Li

Dissertations, Master's Theses and Master's Reports

The research presented in this dissertation investigates whether an increased coercivity of Neodymium-Iron-Boron (Nd2Fe14B) based bulk magnets at elevated temperature (160°C), which is now only obtainable by substituting ~7wt% dysprosium (Dy) for a portion of neodymium (Nd), can be achieved through specific microstructural modifications with decreased Dy concentrations. The approach is to reduce the size of individual crystallographically-aligned grains in the magnet so that each grain can only support a single magnetic domain and to simultaneously dilute the Nd-Fe inter-granular phase present in conventional magnets with a non-Fe-containing, Nd-rich phase (Nd-Cu alloy) in an attempt to partially magnetically isolate the …

The Effect Of Solidification Rate And Solutionizing Quench Rate On The Mechanical Properties And Hardening Response Of Aluminum Alloys: A Quantitative Comparison, Rafael Gil-Figueroa

Dissertations, Master's Theses and Master's Reports

A comparative study of five aluminum alloys was performed to characterize the effect of solidification rate and quench rate on casting microstructure and properties. The alloys were cast in the geometry for Jominy End Quench (JEQ) testing, so as to take advantage of the JEQ test’s ability to give data on multiple quench rates in a single sample and illustrate the quench sensitivity of an alloy. While the Jominy End Quench test has been used in aluminum alloys, the effects of solidification rates have not been assessed in depth. The work done by other studies has either focused on a …

Experimental Investigations Of Fused Filament Fabrication For Applications To Affordable Scientific Hardware, Bas Wijnen

Dissertations, Master's Theses and Master's Reports

This research aims to make science more accessible through the use of open source 3-D printers.

A new control system for CNC machines in general and 3-D printers specifically, is developed and presented that enables web-based control of 3-D tools from any Internet connected device. The system can be set up and controlled entirely from a web interface.

A tool was designed to help apply science to the developing world. The developing world remains plagued by lack of access to safe drinking water. A methodology is provided for the design, development, and technical validation of a low-cost open-source water testing …

Nanosphere Lithography And Its Application In Rapid And Economic Fabrication Of Plasmonic Hydrogenated Amorphous Silicon Photovoltaic Devices, Chenlong Zhang

Dissertations, Master's Theses and Master's Reports

Solar photovoltaic (PV) devices harvest energy from solar radiation and convert it to electricity. PV technologies, as an alternative to traditional fossil fuels, use clean and renewable energy while minimizing pollution. For decades researchers have been developing thin film solar cells as an important alternatives to the relatively expensive bulk crystal solar cell technology. Among those, hydrogenated amorphous silicon (a-Si:H) solar cells prevails for good efficiency, non-toxic and materially abundant nature. However, a-Si:H thickness must be minimized to prevent light induced degradation, so optical enhancement is necessary. Light manipulation has to be applied and carefully engineered to trap light within …

Dynamic Atomistic Study Of Tunnel Functions In Nanostructured Transitional Metal Oxides, Yifei Yuan

Dissertations, Master's Theses and Master's Reports

Alpha (α-) MnO₂ is a well know transitional metal oxide possessing one dimensional 2×2 (4.6 × 4.6 Ų) tunnels for accommodation of various ions. Such a characteristic tunneled structure has enabled the wide applications of α-MnO₂ in the fields of ion exchange, molecular sieves, biosensor, catalysis and energy storage. This PhD dissertation focuses on the dynamic study of ion transport functionality of α-MnO₂ at atomic level using an aberration corrected scanning transmission electron microscopy equipped with a special holder with a scanning tunneling microscopy probe.

The wide application of in situ TEM studying the dynamic …

Methodology For Analyzing Epoxy-Cnt Phononic Crystals For Wave Attenuation And Guiding, Madhu Kolati

Dissertations, Master's Theses and Master's Reports

Phononic crystals (PhnCs) control, direct and manipulate sound waves to achieve wave guiding and attenuation. This dissertation presents methodology for analyzing nanotube materials based phononic crystals to achieve control over sound, vibration and stress mitigation. Much of the analytical work presented is in identifying frequency band gaps in which sound or vibration cannot propagate through these PhnCs. Wave attenuation and mitigation analysis is demonstrated using finite element simulation. Engineering principles from current research areas of solid mechanics, solid-state physics, elasto-dynamics, mechanical vibrations and acoustics are employed for the methodology. A considerable effort is put to show that these PhnCs can …

Damage Tolerance And Assessment Of Unidirectional Carbon Fiber Composites, Mark David Flores

Open Access Theses & Dissertations

Composites are beginning to be used in a variety of different applications throughout industry. However, certification and damage tolerance is a growing concern in many aerospace and marine applications. Although compression-after-impact have been studied thoroughly, determining a damage tolerance methodology that accurately characterizes the failure of composites has not been established. An experimental investigation was performed to study the effect of stacking sequence, low-velocity impact response, and residual strength due to compression and fatigue. Digital Image Correlation (DIC) captured the strains and deformation of the plate due to compression. Computational investigations integrated non-destructive techniques (C-Scan, X-Ray) to determine the extent …

Fatigue Properties Of Magnetorheological Elastomers And The Design Of Interfacial Layers To Improve Fatigue Life., Yanfen Zhou

Doctoral

The primary aim of this PhD programme was to understand the fatigue behaviour of magnetorheological elastomers (MREs) and provide a reliable fatigue life predictor for this class of materials. To realise this aim required the study of the dynamic behaviour of MREs using the equi-biaxial bubble inflation test method. Isotropic and anisotropic MREs were fabricated from silicone rubber (SR) filled with soft carbonyl iron (CI) particles. The equi-biaxial fatigue behaviour of these samples was determined using a bubble inflation method. Wöhler (S-N) curves for both isotropic and anisotropic MREs were produced by subjecting the compounds to cycling over a range …

The Role Of Microbial Exopolymers In Determining The Fate Of Oil And Chemical Dispersants In The Ocean, Antonietta Quigg, Uta Passow, Wei-Chun Chin, Chen Xu, Shawn Doyle, Laura Bretherton, Manoj Kamalanathan, Alicia K. Williams, Jason B. Sylvan, Zoe V. Finkel, Anthony H. Knap, Kathleen A. Schwehr, Saijin Zhang, Luni Sun, Terry L. Wade, Wassim Obeid, Patrick G. Hatcher, Peter H. Santschi

Chemistry & Biochemistry Faculty Publications

The production of extracellular polymeric substances (EPS) by planktonic microbes can influence the fate of oil and chemical dispersants in the ocean through emulsification, degradation, dispersion, aggregation, and/or sedimentation. In turn, microbial community structure and function, including the production and character of EPS, is influenced by the concentration and chemical composition of oil and chemical dispersants. For example, the production of marine oil snow and its sedimentation and flocculent accumulation to the seafloor were observed on an expansive scale after the Deepwater Horizon oil spill in the Northern Gulf of Mexico in 2010, but little is known about the underlying …

Equiaxed Ti-Based Composites With High Strength And Large Plasticity Prepared By Sintering And Crystallizing Amorphous Powder, Lehua Liu, Chao Yang, L. M. Kang, Yan Long, Zhiyu Xiao, Peijie Li, Laichang Zhang

Research outputs 2014 to 2021

High-performance titanium alloys with an equiaxed composite microstructure were achieved by sintering and crystallizing amorphous powder. By introducing a second phase in a β-Ti matrix, series of optimized Ti-Nb-Fe-Co-Al and Ti-Nb-Cu-Ni-Al composites, which have a microstructure composed of ultrafine-grained and equiaxed CoTi₂ or (Cu,Ni)Ti₂ precipitated phases surrounded by a ductile β-Ti matrix, were fabricated by sintering and crystallizing mechanically alloyed amorphous powder. The as-fabricated composites exhibit ultra-high ultimate compressive strength of 2585MPa and extremely large compressive plastic strain of around 40%, which are greater than the corresponding ones for most titanium alloys. In contrast, the alloy fabricated by …

A Practical Anodic And Cathodic Curve Intersection Model To Understand Multiple Corrosion Potentials Of Fe-Based Glassy Alloys In Oh-Contained Solutions, Yingjie Li, Yonggang Wang, Bang An, Hui Xu, Yihua Liu, Laichang Zhang, Houyi Ma, Weimin Wang

Research outputs 2014 to 2021

A practical anodic and cathodic curve intersection model, which consisted of an apparent anodic curve and an imaginary cathodic line, was proposed to explain multiple corrosion potentials occurred in potentiodynamic polarization curves of Fe-based glassy alloys in alkaline solution. The apparent anodic curve was selected from the measured anodic curves. The imaginary cathodic line was obtained by linearly fitting the differences of anodic curves and can be moved evenly or rotated to predict the number and value of corrosion potentials. © 2016 Li et al. This is an open access article distributed under the terms of the Creative Commons Attribution …