Materials Science and Engineering Commons^™

Stm Study Of Pulsed Laser Assisted Growth Of Ge Quantum Dot On Si(1 0 0)-(2 × 1), Ali Orguz Er, Hani E. Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

Ge quantum dot formation on Si(1 0 0)-(2 × 1) by nanosecond pulsed laser deposition under laser excitation was investigated. Scanning tunneling microscopy was used to probe the growth mode and morphology. Excitation was performed during deposition using laser energy density of 25-100 mJ/cm ². Faceted islands were achieved at a substrate temperature of ∼250 °C only when using laser excitation. The island morphology changes with increased laser excitation energy density although the faceting of the individual islands remains the same. The size of the major length of islands increases with the excitation laser energy density. A purely electronic …

Polarization Of Bi2te3 Thin Film In A Floating-Gate Capacitor Structure, Hui Yuan, Kai Zhang, Haitao Li, Hao Zhu, John E. Bonevich, Helmut Baumgart, Curt A. Richter, Qiliang Li

Electrical & Computer Engineering Faculty Publications

Metal-Oxide-Semiconductor (MOS) capacitors with Bi₂Te₃ thin film sandwiched and embedded inside the oxide layer have been fabricated and studied. The capacitors exhibit ferroelectric-like hysteresis which is a result of the robust, reversible polarization of the Bi₂Te₃ thin film while the gate voltage sweeps. The temperature-dependent capacitance measurement indicates that the activation energy is about 0.33 eV for separating the electron and hole pairs in the bulk of Bi₂Te₃, and driving them to either the top or bottom surface of the thin film. Because of the fast polarization speed, potentially excellent …

Zein Film: Effects Of Dielectric Barrier Discharge Atmospheric Cold Plasma, Shashi Pankaj, Carmen Bueno-Ferrer, N. Misra, Paula Bourke, Patrick J. Cullen

Articles

Dielectric barrier discharge atmospheric plasma is a novel non-thermal technology for the food and packaging industry. The effects of dielectric barrier discharge plasma on the surface, structural, thermal and moisture sorption properties of edible zein films have been examined. Plasma treatment increased the surface roughness and equillibrium moisture content of the zein film in a direct relationship with the applied voltage level. No significant difference in the thermal stability of the zein film is also observed after plasma treatment. Dielectric barrier discharge plasma treatments of zein film lead to a change in the protein conformation which is confirmed by X-ray …

In-Situ Tem Plasma Chip Nanofabrication And Characterization, Xuebo Cui

Dissertations, Master's Theses and Master's Reports - Open

A silicon-based microcell was fabricated with the potential for use in in-situ transmission electron microscopy (TEM) of materials under plasma processing. The microcell consisted of 50 nm-thick film of silicon nitride observation window with 60μm distance between two electrodes. E-beam scattering Mont Carlo simulation showed that the silicon nitride thin film would have very low scattering effect on TEM primary electron beam accelerated at 200 keV. Only 4.7% of primary electrons were scattered by silicon nitride thin film and the Ar gas (60 μm thick at 1 atm pressure) filling the space between silicon nitride films. Theoretical calculation also showed …

Nano-Engineering Of Composite Material Via Reactive Mechanical Alloying/Milling (Rma/M), Edward Andrew Laitila

Dissertations, Master's Theses and Master's Reports - Open

Attempts to strengthen a chromium-modified titanium trialuminide by a combination of grain size refinement and dispersoid strengthening led to a new means to synthesize such materials. This Reactive Mechanical Alloying/Milling process uses in situ reactions between the metallic powders and elements from a process control agent and/or a gaseous environment to assemble a dispersed small hard particle phase within the matrix by a bottom-up approach. In the current research milled powders of the trialuminide alloy along with titanium carbide were produced. The amount of the carbide can be varied widely with simple processing changes and in this case the milling …

Development Of Practical Applications For Reprap Style 3-D Printers In Engineering, Benjamin T. Wittbrodt

Dissertations, Master's Theses and Master's Reports - Open

The current rise in popularity of consumer level 3-D printers introduces a need to understand the application and material property capabilities of the technology. Presented here is data demonstrating the ability for the average U.S. consumer to recuperate the cost of a 3-D printer within one year of ownership. Additionally, using a consumer level 3-D printer, multiple photovoltaic (PV) racking systems were printed and produced with much lower cost compared to commercially available aluminum racking. Additionally, mechanical testing on 3-D printed components showed a temperature dependence on both percent crystallinity and ultimate tensile strength. Conclusions are drawn using the information …

Analysis Of The Influence Of Organic Corrosion Inhibitors On Corrosion Of Reinforcement In Concrete Bridge Structure Under Simulated Field Service Environment, Liang Shi, J. Ye, C. C. Chen, Y. Wu, J. Z. Liu

International Conference on Durability of Concrete Structures

For concrete bridge projects in marine environments, attention must be paid to the reinforcement corrosion problems caused by chloride intrusion. As kinds of functional admixtures, which can reduce the reinforcement corrosion rate, corrosion inhibitors are becoming very popular in China in new bridge projects. Corrosion inhibitors cover both inorganic and organic inhibitors. Nitrite is representative of inorganic corrosion inhibitors, but its carcinogenicity has hindered its further development. Organic corrosion inhibitors such as small-molecule-based alcohol amine series are becoming the focus of attention. To guide the scientific applications of organic corrosion inhibitors, China is carrying out broad applications technology research. But …

Processing And Characterization Of Continuous Basalt Fiber Reinforced Ceramic Matrix Composites Using Polymer Derived Ceramics, Sarah Cox

Electronic Theses and Dissertations

The need for high performance vehicles in the aerospace industry requires materials which can withstand high loads and high temperatures. New developments in launch pads and infrastructure must also be made to handle this intense environment with lightweight, reusable, structural materials. By using more functional materials, better performance can be seen in the launch environment, and launch vehicle designs which have not been previously used can be considered. The development of high temperature structural composite materials has been very limited due to the high cost of the materials and the processing needed. Polymer matrix composites can be used for temperatures …

Non-Oxide Porous Ceramics From Polymer Precursor, Xueping Yang

Electronic Theses and Dissertations

Non-oxide porous ceramics exhibit many unique and superior properties, such as better high-temperature stability, improved chemical inertness/corrosive resistance, as well as wide band-gap semiconducting behavior, which lead to numerous potential applications in catalysis, high temperature electronic and photonic devices, and micro-electromechanical systems. Currently, most mesoporous non-oxide ceramics (e.g. SiC) are formed by two-step templating methods, which are hard to adjust the pore sizes, and require a harmful etching step or a high temperature treatment to remove the templates. In this dissertation, we report a novel technique for synthesizing hierarchically mesoporous non-oxide SiC ceramic from a block copolymer precursor. The copolymer …

Freeze Thaw Durability Of Internally Cured Concrete Made Using Superabsorbent Polymers, Wesley A. Jones, W. Jason Weiss

International Conference on Durability of Concrete Structures

The use of superabsorbent polymers (SAPs) to produce internally cured concrete has been shown to be effective in reducing the potential for restrained shrinkage cracking of high performance concrete mixtures. However, not much is known regarding the freeze–thaw durability of concrete mixtures that incorporate SAPs for internal curing (IC). When SAP particles desorb (or partially desorb) the “water” (pore fluid) they contain for the purposes of IC, some believe that the void space created by these particles can provide enough empty voids to accommodate the additional volume caused by water expansion upon freezing. This paper investigates the freeze–thaw durability of …

Influence Of Organic Inhibitor On Corrosion Resistance Of Steel In Simulated Concrete Pore Solution, Jingshun S. Cai, C. C. Chen, J. Z. Liu, J. P. Liu

International Conference on Durability of Concrete Structures

Organic corrosion inhibitor is one of lower cost technologies that limit the deterioration of concrete structures. The influence of a newly prepared organic corrosion inhibitor on the corrosion behavior of carbon steel in simulated concrete pore solution was investigated by polarization curves, electrochemical impedance spectroscopy, and so on. The effect of organic corrosion inhibitors on concrete working performance was also studied. The results show that the corrosion rate decreases with the concentration of inhibitor increase; when the content of inhibitor up to 1.5% versus water, the oxide film was completely passive. Organic corrosion inhibitor had no effect on work performance.

Co2 Sequestration In Cement-Based Materials During Mixing Process Using Carbonated Water And Gaseous Co2, Jacek Kwasny, P. A. Muhammed Basheer, Mark I. Russell, William Doherty, Kieran Owens, Neil Ward

International Conference on Durability of Concrete Structures

This paper presents selected findings from a recently completed research project, aimed at the investigation of CO₂ sequestration in cement-based materials during the early stages of hydration when the cement paste is being mixed. Portland cement pastes were carbonated during the mixing process, using both carbonated water and gaseous CO₂, and their properties were compared to the control non-carbonated mix. All mixes were prepared in a purpose-designed chamber that permitted carbonated water and gaseous CO₂ to be mixed with the cementbased materials during the mixing process, without losses of CO₂ to the external environment. Temperature …

Thermotropic Phase Boundaries In Classic Ferroelectrics, Tom T. A. Lummen, Yijia Gu, Jianjun Wang

Materials Science and Engineering Faculty Research & Creative Works

High-performance piezoelectrics are lead-based solid solutions that exhibit a so-called morphotropic phase boundary, which separates two competing phases as a function of chemical composition; as a consequence, an intermediate low-symmetry phase with a strong piezoelectric effect arises. In search for environmentally sustainable lead-free alternatives that exhibit analogous characteristics, we use a network of competing domains to create similar conditions across thermal inter-ferroelectric transitions in simple, lead-free ferroelectrics such as BaTiO₃ and KNbO₃. Here we report the experimental observation of thermotropic phase boundaries in these classic ferroelectrics, through direct imaging of low-symmetry intermediate phases that exhibit large enhancements …

Atomic Layer Deposition, Paul Kubicza

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Effect Of Er Doping On The Structural And Magnetic Properties Of Cobalt-Ferrite, Sateesh Prathapani, M. Vinitha, Tanjore V. Jayaraman, D. Das

Department of Mechanical and Materials Engineering: Faculty Publications

Nanocrystalline particulates of Er doped cobalt-ferrites CoFe_(2–x)Er_xO₄ (0 ≤ x ≤ 0.04), were synthesized, using sol-gel assisted autocombustion method. Co-, Fe-, and Er- nitrates were the oxidizers, and malic acid served as a fuel and chelating agent. Calcination (400–600 °C for 4h) of the precursor powders was followed by sintering (1000 °C for 4 h) and structural and magnetic characterization. X-ray diffraction confirmed the formation of single phase of spinel for the compositions x = 0, 0.01, and 0.02; and for higher compositions an additional orthoferrite phase formed along with the spinel phase. …

Thermodynamics And Crystallography Of The Γ→Ε→Α' Transformation In Femnalsic Steels, Scott Thomas Pisarik

Masters Theses

"FeMnAlSiC steels which exhibit two-stage transformation induced plasticity (TRIP) behavior characterized by the γ→ε→α' dual stage martensitic transformation promise to take a leading role in the development of 3rd generation advanced high strength steels. The crystallographic orientation relationship of the γ→α' and γ→ε athermal martensitic transformations in these steels has been determined as the Kurdjumov-Sachs and the Shoji-Nishiyama, respectively. Six crystallographic variants of α-martensite consisting of three twin-related variant pairs were observed in ε- bands. A planar parallelism of {0001}ε || {110}α' and a directional relation of α' lying within 1⁰ of ε existed for these variants. Two regular solution …

Correlation Between The Microstructure And Mechanical Properties Of Irradiated Fe-9cr Ods, M. Swenson, C. Dolph, J. Wharry

Materials Science and Engineering Faculty Publications and Presentations

The growing global demand for energy will increasingly call upon fusion reactors and Generation IV nuclear fission reactors to supply safe and reliable energy worldwide. Ferritic/martensitic (F/M) alloys are leading candidates for structural components in these reactors because of their high strength, dimensional stability, and low activation. In novel reactor concepts, these materials will be subject to extreme operating conditions, accumulating doses of irradiation up to a few hundred displacements per atom (dpa) at temperatures as high as 600°C. Oxide dispersion strengthened (ODS) F/M alloys containing a dispersion of Y-Ti-0 nanoclusters have been developed to operate at even higher temperatures.

Joining And Hermetic Sealing Of Silicon Carbide Using Iron, Chromium, And Aluminum Alloys, Andrew Morgan

Theses and Dissertations

Silicon Carbide (SiC) is increasingly gaining attention as a potential fuel cladding material, on account of its favorable thermo-mechanical and neutronic properties. The major limitations of such a cladding is currently associated with joining and hermetic sealing. The work presented here investigated the use of Al, Cr and Fe metals and a specialized alloy (FeCrAl) to achieve hermetic sealing of SiC tubes as well as a joining technology of SiC. Major part of solving this issue requires addressing joining of ceramic and metallic components, which are largely dissimilar in both thermal and mechanical properties. Preliminary experiments to bond SiC with …

Microwave Absorption Properties Of Tires, Yuzhe Zhang

Dissertations, Master's Theses and Master's Reports - Open

The waste tire is belonging to insoluble high polymer elastic materials. It takes hundreds of years to resolve the macromolecules of waste tire into the standard which does not pollute the environment. More and more waste tires are air stored which causes space occupation and mosquito-breeding in the places that will spread diseases. The disposal methods include landfill, stockpiles, dumping and incising into particles. However, all these methods are not technically and economically efficient. The trend for the development of waste tire treatment processes is low cost, on-site, and high product recovery at high energy efficiency. In this project, microwave …

Mse Annual Report 2014, Department Of Materials Science And Engineering, Michigan Technological University

Department of Materials Science and Engineering Annual Reports

Table of Contents

• Department Legends
• Wonder Material
• Student News
• Faculty and Staff News
• Alumni News
• Endowed Scholarships

Thermal Properties Of Zirconium Diboride - Transition Metal Boride Solid Solutions, Devon Lee Mcclane

Masters Theses

"This research focuses on the thermal properties of zirconium diboride (ZrB₂) based ceramics. The overall goal was to improve the understanding of how different transition metal (TM) additives influence thermal transport in ZrB₂. To achieve this, ZrB₂ with 0.5 wt% carbon, and 3 mol% of individual transition metal borides, was densified by hot-press sintering. The transition metals that were investigated were: Y, Ti, Hf, V, Nb, Ta, Cr, Mo, W, and Re. The room temperature thermal diffusivities of the compositions ranged from 0.331 cm²/s for nominally pure ZrB₂ to 0.105 cm²/s for (Zr,Cr)B₂ and converged around 0.155cm²/s at higher temperatures …

Corrosion Resistance Of Enamel Coating Modified By Calcium Silicate And Sand Particle For Steel Reinforcement In Concrete, Fujian Tang

Masters Theses

"Porcelain enamel has stable chemical property in harsh environments such as high temperature, acid and alkaline, and it can also chemically react with substrate reinforcing steel resulting in improved adherence strength. In this study, the corrosion resistances of enamel coating modified by calcium silicate and sand particles, which are designed for improved bond strength with surrounding concrete, were investigated in 3.5 wt% NaCl solution. It consists of two papers that describe the results of the study.

The first paper investigates the corrosion behavior of enamel coating modified by calcium silicate applied to reinforcing steel bar in 3.5 wt% NaCl solution …

Effect And Interactions Of Commercial Additives And Chloride Ion In Copper Electrowinning, Wenyuan Cui

Masters Theses

"This thesis is to understand and compare the effects and interactions of modified polysaccharide (HydroStar), polyacrylamide (Cyquest N-900) and chloride ion on copper electrowinning. A study of the nucleation and growth was conducted in a synthetic electrolyte (40 g/L Cu, 160 g/L H₂SO₄, 20 mg/L Cl-) with the addition of HydroStar or Cyquest N-900 using potential step measurements. The current responses generated were compared to theoretical models of nucleation and growth mechanisms. The nucleation and growth mechanism changed as function of potential and the presence of organic additives. The nucleation and growth mechanisms were confirmed using scanning electron microscopy (SEM). …

Development And Characterization Of Spiral Additions In A Ceramic Matrix, Andrea Lynn Els

Masters Theses

"A novel spiral architecture was formed using titanium diboride and silicon carbide ceramics as either the spiral or matrix phase. Particulate composites with the same compositions were fabricated to compare to the materials in this study. Spiral additions were formed using powder loaded polymers followed by a single and/or multi-filament co-extrusion. For 25 vol% SiC spiral additions to TiB₂, boron nitride was added to the SiC spiral to alter the bonding at the interface and reduce thermal residual stresses. All samples were hot-pressed to near full density at 1980 ⁰C. Hot pressed multi-filament co-extrusion of 2.4 mm / …

Inorganic Biodegradable Devices For Temporary Implants, Kassan Unda

Masters Theses

"Implantable electronic devices have great potential to benefit many health care technologies. They comprise of two different categories. The first is permanent prosthetic devices like cardiac pacemakers or nerve stimulants. The other category includes temporary devices for interventional medical monitoring and control scenarios, which lose functionality and become unnecessary after their intended operational lifetime. This can cause serious electromagnetic and biomechanical safety concerns if not removed from the body by an additional surgical operation.

This thesis focuses on exploring the feasibility of implantable inorganic bioresorbable thin film resistive devices utilizing bioactive glass as the core structural material. This device will …

Structure And Catalytic Properties Of Ultra-Small Ceria Nanoparticles, Xing Huang

Theses and Dissertations--Chemical and Materials Engineering

Cerium dioxide (ceria) is an excellent catalytic material due to its ability to both facilitate oxidation/reduction reactions as well as store/release oxygen as an oxygen buffer. The traditional approach to assess and improve ceria's catalytic behavior focuses on how efficiently O-vacancies can be generated and/or annihilated within the material, and how to extend established understandings of "bulk" ceria to further explain the greatly enhanced catalytic behavior of ultra-small ceria nanoparticles (uCNPs) with sizes less than 10 nm. Here, using density functional theory (DFT) calculations, we reexamine the atomic and electronic structures of uCNPs, especially their surface configurations. A unique picture …

Influence Of Ferrite Phase In Alite-Calcium Sulfoaluminate Cements, Tristana Y. Duvallet

Theses and Dissertations--Chemical and Materials Engineering

Since the energy crisis in 1970’s, research on low energy cements with low CO₂-emissions has been increasing. Numerous solutions have been investigated, and the goal of this original research is to create a viable hybrid cement with the components of both Ordinary Portland cement (OPC) and calcium sulfoaluminate cement (CSAC), by forming a material that contains both alite and calcium sulfoaluminate clinker phases. Furthermore, this research focuses on keeping the cost of this material reasonable by reducing aluminum requirements through its substitution with iron. The aim of this work would produce a cement that can use large amounts …

The Development And Biocompatibility Of Low Temperature Co-Fired Ceramic (Ltcc) For Microfluidic And Biosensor Applications, Jin Luo

Theses and Dissertations--Chemical and Materials Engineering

Low temperature co-fired ceramic (LTCC) electronic packaging materials are applied for their electrical and mechanical properties, high reliability, chemical stability and ease of fabrication. Three dimensional features can also be prepared allowing integration of microfluidic channels and cavities inside LTCC modules. Mechanical, optical, electrical, microfluidic functions have been realized in single LTCC modules. For these reasons LTCC is attractive for biomedical microfluidics and Lab-on-a-Chip systems. However, commercial LTCC systems, optimized for microelectrics applications, have unknown cytocompatibility, and are not compatible with common surface functionalization chemistries.

The first goal of this work is to develop biocompatible LTCC materials for biomedical applications. …

Nanometer-Scale Membrane Electrode Systems For Active Protein Separation, Enzyme Immobilization And Cellular Electroporation, Zhiqiang Chen

Theses and Dissertations--Chemical and Materials Engineering

Automated and continuous processes are the future trends in downstream protein purification. A functionalized nanometer-scale membrane electrode system, mimicking the function of cell wall transporters, can selectively capture genetically modified proteins and subsequently pump them through the system under programmed voltage pulses. Numerical study of the two-step pulse pumping cycles coupled with experimental His-GFP releasing study reveals the optimal 14s/1s pumping/repel pulse pumping condition at 10 mM bulk imidazole concentration in the permeate side. A separation factor for GFP: BSA of 9.7 was achieved with observed GFP electrophoretic mobility of 3.1×10^-6 cm² s^-1 V^-1 at 10 …

Cnt Membrane Platforms For Transdermal Drug Delivery And Aptamer Modulated Transport, Tao Chen

Theses and Dissertations--Chemical and Materials Engineering

CNT membrane platforms are biomimetic polymeric membranes imbedded with carbon nanotubes which show fast fluid flow, electric conductivity, and the ability to be grafted with chemistry. A novel micro-dialysis probe nicotine concentration sampling technique was proposed and proved in vitro, which could greatly improve the efficiency and accuracy of future animal transdermal studies. To enhance the scope of transdermal drug delivery which was limited to passive diffusion of small, potent lipophilic drugs, a wire mesh lateral electroporation design was also proposed which could periodically disrupt the skin barrier and enhance drug flux.

It was shown that AMP binding aptamer …