Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Journal of Electrochemistry

Articles 1471 - 1500 of 1823

Full-Text Articles in Materials Science and Engineering

Studies On The Anti-Corrosion Behavior Of Corrosion Inhibitor To The Ship Building Steel In Moist Air, Yong-Tao Zhao, Jian-Hua Wu, Jia Wang Nov 2001

Studies On The Anti-Corrosion Behavior Of Corrosion Inhibitor To The Ship Building Steel In Moist Air, Yong-Tao Zhao, Jian-Hua Wu, Jia Wang

Journal of Electrochemistry

The anti corrosion behavior of 907A steel, which were covered with thin inibitor layers in moist air, were simulated, The electrochemical measurements, including EIS method and the coulostatic method, were used to atmospheric corrosion monitor (ACM) under thin inhibitor layers to study the mechanism of rust preventiion. the results shown that the mechanism of inhibiting corrosion was different from the steel immersed in inhibitor solutin, the anodic reaction process under thin inhibitor layers had the advantage over that of cathodic for blocking the speed of corrosion. At the later stage of soaking, the blend feature due to the electrochemical process …

Go to article

The Investigation Of Prepare Condition For Micropores Membranes From Poly(Vinylidene Fluoride), Xu-Mei Ren, Feng Wu, Ying Bai, Hang-Jun Li, Xue-Jie Huang Nov 2001

The Investigation Of Prepare Condition For Micropores Membranes From Poly(Vinylidene Fluoride), Xu-Mei Ren, Feng Wu, Ying Bai, Hang-Jun Li, Xue-Jie Huang

Journal of Electrochemistry

The micropores membranes from Poly (vinylidene fluoride) were prepared by the phase inversion process. The effects of the casting solution composition, exposure time prior to coagulation and temperature of the coagulation bath on properties of prepared membranes were investigated. For all prepared membranes an asymmetric structure, sometimes without a dense skin layer, was observed.

Go to article

An Investigation Of Structural Properties Of Li-Al-Mixed Doped Spinels Materials Li 1+XAlYMn Z-YO4, Zi-Shan Zheng, Zi-Long Tang, Zhong-Tai Zhang, Wan-Ci Sheng Nov 2001

An Investigation Of Structural Properties Of Li-Al-Mixed Doped Spinels Materials Li 1+XAlYMn Z-YO4, Zi-Shan Zheng, Zi-Long Tang, Zhong-Tai Zhang, Wan-Ci Sheng

Journal of Electrochemistry

Al and Li elements were co-doped into host spinel lithium manganese oxide by a simple and economical preparation technology. There was an investigation of the influence of doped Al contents on the initial capacity and cycling performance of the materials. The investigation of the XRD patterns, the analysis of the SEM micrographs and the determination of IR spectroscopy showed that the particles of dopant materials are fine, narrowly distributed and well crystallized, and the bonds Mn-O are stronger than these of undoped materials. The resulted materials have a high initial capacity of 119 mAh/g and good cycling characterization. The capacity …

Go to article

Studies On The Properties Of The Anodic Films Formed On Lead- Lanthanum And Lead-Samarium Alloys In Sulfuric Acid Solution, Hou-Tian Liu, Chun-Xuao Yang, Hai-Heng Liang, Jiong Yang, Wei-Fang Zhou Nov 2001

Studies On The Properties Of The Anodic Films Formed On Lead- Lanthanum And Lead-Samarium Alloys In Sulfuric Acid Solution, Hou-Tian Liu, Chun-Xuao Yang, Hai-Heng Liang, Jiong Yang, Wei-Fang Zhou

Journal of Electrochemistry

AC voltammetry, linear sweep voltammetry, and cyclic voltammetry were applied to study the anodic corrosion of Pb, Pb-1.0 at% La and Pb-1.0 at% Sm electrodes in 4.5 mol·dm-3 H2SO4 solution (25 ℃). The experiment results show that samarium can inhibit the anodic corrosion of lead and decrease the impedance of anodic Pb(Ⅱ) film. Lanthanum can also decrease the impedance of the anodic Pb(Ⅱ)film, but the effect is smaller.

Go to article

The Research Of Organic Electrolyte Solutions For Li-Ion Batteries, Quang-Chao Zhuang, Shan Wu, Wen-Yuan Liu, Zhao-Da Lu Nov 2001

The Research Of Organic Electrolyte Solutions For Li-Ion Batteries, Quang-Chao Zhuang, Shan Wu, Wen-Yuan Liu, Zhao-Da Lu

Journal of Electrochemistry

The characteristics of organic electrolyte solutions and its influences on the ion conductivity are summarized. The chemistry and electrochemistry of organic electrolyte solutions and characteristics of ordinary organic solvents are introduced. Progresses in studies of organic electrolyte solutions such as electrolyte salts, organic solvents, additives in recent years are reviewed, current situation of the studies of organic electrolyte solutions were also discussed.

Go to article

New Progress Of Intrinsic Conducting Polymers' Application, Wan Chen, Cheng-Hao Liang, Yang Xie Nov 2001

New Progress Of Intrinsic Conducting Polymers' Application, Wan Chen, Cheng-Hao Liang, Yang Xie

Journal of Electrochemistry

As a kind of functional polymer, the intrinsic conducting polymer has the special chemical, electrochemical and optical properties. So it has wide application such as batteries, electromagnetic wave shielding, electroluminescent etc. Recent development and the problems of the intrinsic conducting polymers' application were briefly reviewed in this paper.

Go to article

Thermal Effects On The Measurement Of Photocurrent At Anodic Films On Silver Electrode, Yuan Gu, Zhi-Yu Jiang Nov 2001

Thermal Effects On The Measurement Of Photocurrent At Anodic Films On Silver Electrode, Yuan Gu, Zhi-Yu Jiang

Journal of Electrochemistry

The influence of heat on the photocurrent of Ag electrde in alkaline solution was investigated by measuring photocurrent, photothermal signal and thermal current under the irraiation of laser beams with the wavelengths of 488 nm and 532 nm. It was found the photocurrent atthe Ag2O film was influenced by the temperature change at the electrode surface under the irradiation of light. During the electrochemical transfer between Ag, Ag2O and AgO in the anodic filmthe surface temperature changed obviously due to the different absprptance of the surface subrstances.It was suggested by comparing the voltammograms, photocurrent curves and …

Go to article

Study Of Hydrogen Diffusion Behavior In Hydrogen Storage Alloy Mlni3.75Co0.65Mn0.4Al0.2 With Potential Step Method, Xian-Xia Yuan, Nai-Xin Xu Nov 2001

Study Of Hydrogen Diffusion Behavior In Hydrogen Storage Alloy Mlni3.75Co0.65Mn0.4Al0.2 With Potential Step Method, Xian-Xia Yuan, Nai-Xin Xu

Journal of Electrochemistry

Potential step method was employed to study the hydrogen diffusion behavior in hydrogen storage alloy MlNi3.75 Co0.65Mn0.4Al0.2 with various depth of discharge (DOD) at ambient temperature and with 50% DOD at various temperatures. It was found that hydrogen diffusion cofficient in the hydrogen storage alloy increaes with the increase in DOD at ambient temperature. and for the alloy with 50% DOD, the hydrogen diffusion coefficient increases with the increase in temperature and the activation energy for hydrogen diffusion in the alloy is 19.87 kJ/mol.

Go to article

Research Progress On Proton Exchange Membranes Of Fuel Cells, Jing-Rong Yu, Dan-Min Xing, Fu-Qiang Liu, Jian-Guo Liu, Bao-Lian Yi Nov 2001

Research Progress On Proton Exchange Membranes Of Fuel Cells, Jing-Rong Yu, Dan-Min Xing, Fu-Qiang Liu, Jian-Guo Liu, Bao-Lian Yi

Journal of Electrochemistry

The proton exchange membrane fuel cells (PEMFC) use proton exchange membranes(PEM) as their electrolytes. The performance of the PEMFC is strongly dependent on the characteristics of the PEM. In this paper, the requirements of the PEM utilized in the PEMFC were analyzed. The per-fluorinated, partially fluorinated and non-fluorinated PEM were introduced respectively. The structures, preparation, properties of the various types of PEM and their applications in the PEMFC were also discussed in detail.

Go to article

The Influence Of Synthesis Conditions On The Electrochemical Properties Of Spinel Limn2O4, Jun-Feng Xu, Zhi-Yu Jiang Nov 2001

The Influence Of Synthesis Conditions On The Electrochemical Properties Of Spinel Limn2O4, Jun-Feng Xu, Zhi-Yu Jiang

Journal of Electrochemistry

The electrochemical properties of spine LiMn2O4 synthesized via a solid state reaction were investigated. Electrolysis MnO2(EMD), Li2CO3 ,LiOH and LiNO3 were used as the initial materials. It was found that the electrochemical properties of LiMn2O4 were strongly influenced by the synthesis conditions. The LiMn2O4 sample sprepared via the reactionof EMD and LiNO3 showed the best properties for a lithiumion intercalation reaction. The procedure includes two steps:pretreatment at 280 ℃ for 6 hours to initiate the permeation of melting LiNO3 into the microporesof EMD …

Go to article

Adsorption And Oxidation Of Methanol On Pt And Sb, S Modified Pt Electrodes Using Cyclic Voltammetry And Eqcm, Guo-Liang Chen, Sheng-Pei Chen, Heng Lin, Xing-Hong Zheng, Shi-Gang Sun Nov 2001

Adsorption And Oxidation Of Methanol On Pt And Sb, S Modified Pt Electrodes Using Cyclic Voltammetry And Eqcm, Guo-Liang Chen, Sheng-Pei Chen, Heng Lin, Xing-Hong Zheng, Shi-Gang Sun

Journal of Electrochemistry

The processes of adsorption and oxidation of methanol on Pt, Pt/Sb ad and Pt/S ad electrodes were studied by using cyclic voltammetry and electrochemical quartz crystal microbalance (EQCM). The results demonstrated that the oxidation of methanol depends strongly on oxidation states of electrode surface. Sb adatoms on Pt surface can adsorb oxygen at relatively low potentials, and exhibit catalytic effects for methanol oxidation. In contrast to Pt electrodes, the oxidation peak potential of methanol in this case negatively shifted to about 130 mV. In a contrary, the oxidation of Sad atoms consumes oxygen species of Pt electrode surface. As …

Go to article

Study On Electrochemical Behavior Of Copper In Nh3 ·H2O Solution Medium Including K3[Fe(Cn)6] During Cmp, Yue-Hua Hu, Han-Wei He, Ke-Long Huang Nov 2001

Study On Electrochemical Behavior Of Copper In Nh3 ·H2O Solution Medium Including K3[Fe(Cn)6] During Cmp, Yue-Hua Hu, Han-Wei He, Ke-Long Huang

Journal of Electrochemistry

Influence of medium pH value and passivator concentrations on the copper passivation and CMP process were studied by electrochemical measurement technologies, relations of the film thickness and tightness with polishing process and polishing rates were investigated. Electrochemical variables influencing polishing process and rates were found out. Electochemical mechanism of polishing processes were explained by corrosion potential and corrosion current density. A recipe of K3[Fe(CN)6] as passivator and nano sized γ-Al2O3 as abrasives in medium of NH3·H2O solution was confirmed reasonable. It is shown that the conditions of polishing process …

Go to article

Study On The Anticorrosion Of Ld-2 Compound Inhibitor On Reinforcing Steel In Seawater, Rong-Gui Du, Zhou-Cheng Wang, Ruo-Shuang Huang, Rong-Gang Hu, Bing Zhao, Jian-Guang Tan, Chang-Jian Lin Nov 2001

Study On The Anticorrosion Of Ld-2 Compound Inhibitor On Reinforcing Steel In Seawater, Rong-Gui Du, Zhou-Cheng Wang, Ruo-Shuang Huang, Rong-Gang Hu, Bing Zhao, Jian-Guang Tan, Chang-Jian Lin

Journal of Electrochemistry

The effect of LD-2 compound inhibitor developed in our laboratory on its anticorrosion action on the reinforcing steel in concrete immersed in seawater was shown in this paper. The corrosion behavior of the reinforcing steel in seawater was studied using electrochemical techniquesand immersion tests. The polarization curve of the reinforcing steel immersed in seawater showedthe free corrosion potential of the steel increased by 0. 220 V (vs. SCE), and the corrosion current decreased by two orders of magnitude by adding 25 g⋅L-1 compound inhibitor to the seawater. The potentiodynamic anodic polarization curve of reinforcing steel in the seawater with …

Go to article

Characterization And Electrochemical Investigation Of Boron-Doped Mesocarbon Microbeads Anode Materials For Lithium-Ion Battery, Mao-Hui Chen, Guo-Tao Wu, Guang-Ming Zhu, Jin-Kua You, Zu-Geng Lin Aug 2001

Characterization And Electrochemical Investigation Of Boron-Doped Mesocarbon Microbeads Anode Materials For Lithium-Ion Battery, Mao-Hui Chen, Guo-Tao Wu, Guang-Ming Zhu, Jin-Kua You, Zu-Geng Lin

Journal of Electrochemistry

The anodic performances of boron doped and undoped mesocarbon microbeads(MCMBs) were comparatively studied and the structures were characterized by XPS, SEM, XRD and electrochemical measurements. It was found that boron doping samples greatly increased the degree of graphitization and the crystallite size, leading to quite different morphology. Electrochemical discharge/charge cycle tests indicate that lithium intercalation occurred at a little higher potential for the boron doped MCMBs, being attended by greater irreversible capacity loss.

Go to article

Microstructure And Electrochemical Properties Of The Melt-Spinning Zr0.9Ti0.1(Ni, Co, Mn, V)2.1 Alloy, Ming-Fen Wen, Yu-Chun Zhai, Lian Chen, Min Tong, Hua Zhen, Rong-Jun Ma Aug 2001

Microstructure And Electrochemical Properties Of The Melt-Spinning Zr0.9Ti0.1(Ni, Co, Mn, V)2.1 Alloy, Ming-Fen Wen, Yu-Chun Zhai, Lian Chen, Min Tong, Hua Zhen, Rong-Jun Ma

Journal of Electrochemistry

The microstructure and electrochemical properties of Zr0.9Ti0.1(Ni,Co,Mn,V)2.1 alloys prepared by both the melt-spinning method and the conventional induction melting were investigated. XRD studies show that Zr0.9Ti 0.1(Ni,Co,Mn,V)2.1 alloys at as-cast, melt-spinning and annealing are all face center cubic structure with C15 laves phase, the higher the melt-spinning rate, the more the amorphous content. The electrochemical measurements show that melt-spinning alloys have better active behavior, low discharge capacity (< 280 mAh/g); but after annealed, the alloys are activated completely with 30 cycles, the capacities about 340 mAh/g are higher than those of as-cast and melt-spinning alloys; the annealec alloys have a better cycle stability than that of as-cast alloy, and the higher the melt-spinning rate is, the more stable the alloy becomes; at 300 mAh/g current density, the capacity of annealed 40 m/s alloy is up to 85% of the maximum capacity after 800 cycles, the capacity decay rate is about 6.9%.

Go to article

The Coulostatic Method For Evaluating Corrosion In Reinforced Concrete, Yong-Tao Zhao, Jian-Hua Wu, Chang-Jiu Zhao Aug 2001

The Coulostatic Method For Evaluating Corrosion In Reinforced Concrete, Yong-Tao Zhao, Jian-Hua Wu, Chang-Jiu Zhao

Journal of Electrochemistry

In the present paper, the application of the coulostatic method to the corrosion of steel in concrete was reviewed. By comparing with other electrochemical techniques, the results obtained in the previous work reveal that the coulostatic method is an interesting alternative to the usual procedures for estimation of corrosion rate, and is better than them in some respects. The main advantages are as follows. The signal to be used can be instantaneous and as small as desired, so the electrode is minimally perturted during the measuring process. In addition, it is as rapid and quantitative, and at least as reliable …

Go to article

Charge/Discharge Characteristics And Structural Changing Of Spherical β-Ni(Oh)2 Prepared From Different Nickel Salt, Shu-Ting Yang, Yan-Hong Yin, Hong-Jun Chen, Jun-Hua Jia, Ming-Chum Zhang, Li Ding Aug 2001

Charge/Discharge Characteristics And Structural Changing Of Spherical β-Ni(Oh)2 Prepared From Different Nickel Salt, Shu-Ting Yang, Yan-Hong Yin, Hong-Jun Chen, Jun-Hua Jia, Ming-Chum Zhang, Li Ding

Journal of Electrochemistry

Spherical β-Ni(OH)2 was prepared from different nickel salt by homogeneous complexing precipitation method. Its charge/discharge and cyclic voltammetry properties were studied. The authors found that there are many differences in the electrochemical properties of the prepared Ni(OH)2.The specific capacity, cycling life and the discharging plateau of the material prepared from NiSO4 were superior to those of the material prepared from Ni(NO3)2. The reasons of the differences were analyzed by XRD and FTIR measurements, which will become abasis for the selection of raw materials.

Go to article

In Situ Ftir Reflection Spectroscopy Of Bioelectrode, Sa-Ying Dong, Guang-Yu Zhao, Yuzhu Gao, Guang-Zhang Chen, Ming-Xiang Lv Aug 2001

In Situ Ftir Reflection Spectroscopy Of Bioelectrode, Sa-Ying Dong, Guang-Yu Zhao, Yuzhu Gao, Guang-Zhang Chen, Ming-Xiang Lv

Journal of Electrochemistry

In situ FTIR reflection spectroscopy was used to study mediated enzyme electrode and immunoelectrode. We determined and analyzed IR characteristic spectra of GOD and glucose by the use of potential difference spectra and single beam subtractive spectra. At last, we explored the IR absorption characters of enzyme-immunoelectrode.

Go to article

The Influence Of Membrane Resistance On The Electrochemical Behavior Of Gold Electrode Modified By Self-Assembled Monolayer, Xiao-Li Cui, Zhi-Yu Jiang Aug 2001

The Influence Of Membrane Resistance On The Electrochemical Behavior Of Gold Electrode Modified By Self-Assembled Monolayer, Xiao-Li Cui, Zhi-Yu Jiang

Journal of Electrochemistry

The electrochemical behavior of gold electrode modified by hexadecanethiol self-assembled monolayer (SAM) in the solution of Fe(CN)63-/Fe(CN)64- was investigated by cyclic voltammetry and ac impedance spectroscopy. The pinhole-free SAM-modified gold electrode has excellent blocking properties to the interfacial electron transfer from redox couple in solution to the substrate. The current increased exponentially with the overpotential at the high potential region. A good linear relationship between ln(I/η) and η1/2 was observed. A model system Au/SAM/Hg was constructed and its I～V curve was measured. Similar phenomena were observed. There was also a linear relationship between ln(I/V) …

Go to article

Codeposition And Corrosion Resistance Of Nickel-Cerium-Phosphorus Amorphous Alloys, Jiang Liu, Xiong Jiang, Lin-Cai Jiang, Ze-Shan Zhu Aug 2001

Codeposition And Corrosion Resistance Of Nickel-Cerium-Phosphorus Amorphous Alloys, Jiang Liu, Xiong Jiang, Lin-Cai Jiang, Ze-Shan Zhu

Journal of Electrochemistry

The possibility of electrodeposition of rare earth alloys from aqueous bath was investigated using varous techniques such as linear potential sweeping, cyclic voltammetry, electrodepositon at constant potential etc. The Ni-Ce-P alloys with different cerium content were electrodeposited from a weakly acidic solution containing CeCl3, NaH2PO2 and so on the crystal structure and component were characterized by XPS, AES, XRD and SEM observation. The codeposits were found to be more highly corrosion resistent than that of Ni-P amorphous alloys by measuring polarization resistance and corrosion potential. The effects of codeposition conditions on the corrosion resistance were …

Go to article

Current Oscillations In The System Of Carbon Steel/Phosphoric Acid/Platinum, Shao-Yuan Shi, Jin-Ping Wu, Jing Liu, An Lin Aug 2001

Current Oscillations In The System Of Carbon Steel/Phosphoric Acid/Platinum, Shao-Yuan Shi, Jin-Ping Wu, Jing Liu, An Lin

Journal of Electrochemistry

The periodic,aperiodic, chaotic and mixed-mode oscillations can occur in the process of the anodic electrodissolution of carbon steel in the solution of dilute phosphoric acid. More plentiful dynamic behaviors can be found in this system compared with the system of Fe/H3PO4/Pt.

Go to article

The Activation Mechanism Of Al Alloys With Tin And Gallium In Alkaline Electrolytes, Zhen-Ya Li, Ling Yi, Zhi-Hui Liu, Lin Yang, Jing-Xin Su, Yan-Ying Chen Aug 2001

The Activation Mechanism Of Al Alloys With Tin And Gallium In Alkaline Electrolytes, Zhen-Ya Li, Ling Yi, Zhi-Hui Liu, Lin Yang, Jing-Xin Su, Yan-Ying Chen

Journal of Electrochemistry

The major reason for Al-anode's activation is that Ga and Sn deposit on the aluminum surface and form activated points. The Al-Sn and Al-Ga binary alloys can't be activated in alkaline medium. During the dissolution of the Al-Sn-Ga ternary anode, Sn and Ga dissolve into the solution and transform into ions. After the Sn ions deposit on the surface of Al-anode, the Ga ions will deposit on Sn. The higher activation of the polynary alloy anode is caused by much more new activated points composed of Ga-Sn alloy being continually formed. Ga- Sn alloy with low melting point deposited on …

Go to article

Determination Of Hydrogen Diffusion Coefficient In Metal Hydride Electrode With Electrochemical Impedance Spectroscopy, Xian-Xia Yuan, Nai-Xin Xu Aug 2001

Determination Of Hydrogen Diffusion Coefficient In Metal Hydride Electrode With Electrochemical Impedance Spectroscopy, Xian-Xia Yuan, Nai-Xin Xu

Journal of Electrochemistry

Electrochemical impedance spectroscopy was employed to determine the hydrogen diffusion coefficient in MlNi 3.75Co 0.65 Mn0.4Al0.2 metal hydride electrode with various states of charge (SOC) at room temperature and with 50% SOC at various temperatures. It was found that hydrogen diffusion coefficient in this electrode decreases with the increase in SOC at ambient temperature, and for the electrode with 50% SOC, hydrogen diffusion coefficient increases with the increase of temperature and the activation energy for hydrogen diffusion in it is 35 kJ/mol.

Go to article

A New Method For Impregnating Nafion Solution Into The Electrode Of Pemfc, Qian Tang, Ming Han, Bao-Lian Yi, Zhi-Yin Lin Aug 2001

A New Method For Impregnating Nafion Solution Into The Electrode Of Pemfc, Qian Tang, Ming Han, Bao-Lian Yi, Zhi-Yin Lin

Journal of Electrochemistry

We have developed a new method for impregnating Nafion solution into the catalyst layer of homemade hydrophobic electrode using capillary process. Those electrodes show better performance and higher utilization of catalyst (detected by CV and TEM) than traditional spray method in PEMFC. According to the results of SEM photograph and linear-analysis of sulfur and platinum for the electrode cross-section, we can conclude that the resin is uniform in the catalyst layer and has almost same depth as catalyst in the impregnated electrode. While in traditional method resin is not uniform in the catalyst layer and penetrates into the diffusion layer, …

Go to article

Performance Of Proton Exchange Membranefuel Cell With Co/H2 Fuel, Hong-Mei Yu, Zhong-Jun Hou, Bao-Lian Yi, Ke-Wan Bi, Jing-Xin Zhang, Zhi-Yin Lin, Ming Han May 2001

Performance Of Proton Exchange Membranefuel Cell With Co/H2 Fuel, Hong-Mei Yu, Zhong-Jun Hou, Bao-Lian Yi, Ke-Wan Bi, Jing-Xin Zhang, Zhi-Yin Lin, Ming Han

Journal of Electrochemistry

Fuel of proton exchange membrane fuel cell(PEMFC) mostly comes from reformatecontains CO which will poison the fuel cell electrocatalyst. The effect of CO on the performance of PEMFC was studied in this paper. The results of the experiment show that when CO is fed inPEMFC ,the cell voltage will be decreased violently,then it will become steady with some vibration. The poison will become more serious with higher CO content and weaker at higher temperature. The adsorption of CO on the electrocatalyst is reversible. The PtRu electrocatalyst is moresuitable for the electrocatalysis of CO/H2 than Pt electrocatalyst.

Go to article

Atmospheric Corrosion Of Steels In China, Cai-Feng Liang May 2001

Atmospheric Corrosion Of Steels In China, Cai-Feng Liang

Journal of Electrochemistry

Data of eight year atmospheric exposures of 17 steels at 7 sites in China were analyzed. The result showed that the most detrimental pollution is sulfur dioxide and chloride ion for corrosion of carbon steels and low alloy weathering steels. This is in accordance with the common knowledge.The effect of sulfur dioxide is serious in the first few years and becomes weak obviously in the later years. The environment factor of humid hot is much more important in long run than the ordinarily acknowledged humidity, pollution for non weathering steels,although it is not obvious in the beginning. If pollution were …

Go to article

Properties Of Metallized Polyo-Toluididemembrane Modified Electrode, Li-Zong Dai, Yi-Ting Xu, Hui-Huang Wu May 2001

Properties Of Metallized Polyo-Toluididemembrane Modified Electrode, Li-Zong Dai, Yi-Ting Xu, Hui-Huang Wu

Journal of Electrochemistry

The platinum particles were electrodeposited on poly(o-toluidide), POT, modified electrode, and the surface configuration and crystal orientation of Pt particles were investigated by SEM and XRD. At the same time the oxidation of isopropanol on platinized POT modified electrode was studied. The results indicate that Pt particles deposite towards preferred-orientation; moreover the increase in polymer electroactivity due to proton doping affects the dimension and graininess of deposited Pt particles. At the metallized polymer electrode the oxidation of isopropanol can occur in POT electroactive potential region, however at the more positive than 0.70 V (SCE) potential where POT loses redox activity …

Go to article

Galvanic Corrosion Of Tin-W Electro-Couple During Tungsten Chemical Mechanical Polishing, Xuan Cheng, Chang-Jian Lin May 2001

Galvanic Corrosion Of Tin-W Electro-Couple During Tungsten Chemical Mechanical Polishing, Xuan Cheng, Chang-Jian Lin

Journal of Electrochemistry

Chemical mechanical polishing (CMP) is a process whereby mechanicaland chemical forces are combined to remove material from a wafer and polish it to a flatsurface. Tungsten CMP is an important prcess to gain the global planarity of siliconwafers with tungsten (W) plugs. Tungsten is actually deposited on a thin adhesive layerof titanium nitride (TiN) on silicon. When close to the final stage of polishing, TiN and W will be simultaneously exposed to the polishing chemistry, forming a galvaniccouple. The corrsion of TiN and W couple will result in different polish rate.

Go to article

Electrochemical Behavior Of Tinicu Shape Memry Alloy In Simulated Body Fluid, Cheng-Hao Liang, Hong-Yan Sui May 2001

Electrochemical Behavior Of Tinicu Shape Memry Alloy In Simulated Body Fluid, Cheng-Hao Liang, Hong-Yan Sui

Journal of Electrochemistry

The study of TiNiCu shape memory alloys (SMA) in Hank's simulated body fluidwas carried out. The results showed that narrow passive range was found in acid environment andactive anodic dissolution was discovered at 100~150 mV vs SCE on anodic polarization cure ofTiNiCu SMA. Temperature had little effect on anodic polarization. With the decrease of pH andthe increase of Cl- concentration ,pitting corrosion potential (Eb) shifted negatively. The electrochemical capability of TiNiCu SMA was inferior to that of TiNi SMA. Observations by means ofXRD and SEM indicate that TiNiCu SMA is not in single crystal structure, which caused …

Go to article

Study Of The Oxidation Dynamics Of Tizro2 Metal-Ceramics, Wen-Chao Li, Li-Dong Teng May 2001

Study Of The Oxidation Dynamics Of Tizro2 Metal-Ceramics, Wen-Chao Li, Li-Dong Teng

Journal of Electrochemistry

The oxidation dynamics of hot-pressed Ti-ZrO2 metal-ceramics with the compositionof 50 vol.% Ti and 50 vol.% ZrO2 has been studied.Thermodynamic analysis shows that Ticould react with O2 but not with N2 in the oxidizing process of TiZrO2 composites at 0.1 MPa air. The oxidation dynamic behavior of Ti-ZrO2 composites is analogous to that of pure Ti. Theactivation energy for the oxygen diffusion in Ti-ZrO2 composites is higher than that in Ti solutions, for the presence of ZrO2 restrains the oxygen diffusion in Ti-ZrO2 composites. At early stagethe oxidation of Ti-ZrO2 …

Go to article

First Prev Next Last