Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Journal of Electrochemistry

Articles 1171 - 1200 of 1829

Full-Text Articles in Materials Science and Engineering

Variable Frequence Switching Power Supply Used To Aluminum Foil Corrosion, Xiang-Dong Zhuo, Lan Sun, Guo-Qing Qian, Chang-Jian Lin Feb 2007

Variable Frequence Switching Power Supply Used To Aluminum Foil Corrosion, Xiang-Dong Zhuo, Lan Sun, Guo-Qing Qian, Chang-Jian Lin

Journal of Electrochemistry

A new variable frequence and multi-wave power supply used to aluminum foil corrosion is introduced. The switching supply power supply controlled by the microcontroller and Variable Frequence in low band and multi-wave, big power supply controlled by the electronic switch bridge for changing phase were designed. This power supply does not need bulky and cumbersome transformer, and the frequency at lower limit is not limited, even lower than 1Hz.

Go to article

Electrochemical Oxidation Of The Phenol In The Chloride System, Yong Liu, Dan Liu, Shi-Lin Zhao, Jing-Jing Lai Feb 2007

Electrochemical Oxidation Of The Phenol In The Chloride System, Yong Liu, Dan Liu, Shi-Lin Zhao, Jing-Jing Lai

Journal of Electrochemistry

The Ru-Ir /Ti electrode as cathode to electrolysis the synthetic phenolic wastewater was studied. The effect of the initial chloride concentration on the electrolytic treatment result has been discussed. Experiment result shows that the electrochemical oxidation of phenol suits to one kinetics equation in given electrolytic time. If the initial chloride concentration in wastewater increases, the time of the electrochemical oxidation of phenol can be shorten, in other words the apparent rate constant is greater. The middle matters of electrochemical oxidation of phenol in the chloride system detected out by HPLC and GC-MS is mainly 1-chloro-phenol, 4-chloro-phenol, 2,4-dichloro-phenol, 2,6-dichloro-phenol, 2,4,6-trichloro-phenol, …

Go to article

Composite Electroplating And Characterizations Of Sn-Sba15 Anode For Lithium-Ion Batteries, Xiao-Yong Fan, Jin-Mei Xu, Quan-Chao Zhuang, Hong-Hong Jiang, Ling Huang, Yan-Xia Jiang, Quan-Feng Dong, Shi-Gang Sun Feb 2007

Composite Electroplating And Characterizations Of Sn-Sba15 Anode For Lithium-Ion Batteries, Xiao-Yong Fan, Jin-Mei Xu, Quan-Chao Zhuang, Hong-Hong Jiang, Ling Huang, Yan-Xia Jiang, Quan-Feng Dong, Shi-Gang Sun

Journal of Electrochemistry

Sn-SBA15 anode was prepared by composite electroplating. The first discharge and charge capacity was 1075mAh/g and 630mAh/g respectively. After fifty charge/discharge cycles, the charge and discharge capacity of Sn-SBA15 were retained above 400mAh/g. XRD patterns indicated that the Sn-SBA15 has tetragonal crystal type. SEM images showed that the Sn-SBA15 had a honeycombed surface. EIS results indicated that there was SEI film formed on the surface of Sn-SBA15 electrode.

Go to article

Comparison Of The Electrochemical Reactivity Of Electrodes Modified By Carbon Nanotubes With Different Sizes, Guo-Feng Yang, Neng-Qin Jia, Zhi-Yong Wang Feb 2007

Comparison Of The Electrochemical Reactivity Of Electrodes Modified By Carbon Nanotubes With Different Sizes, Guo-Feng Yang, Neng-Qin Jia, Zhi-Yong Wang

Journal of Electrochemistry

The electrochemical activity of multi-walled carbon nanotubes(MWNTs) with different sizes,including four different MWNTs with the same length and different diameter,two different MWNTs with the same diameter and different length has been assessed and compared.The various MWNTs modified electrodes were prepared by immobilizing the suitable amount of MWNTs onto a glassy carbon electrode,and their voltammetric responses to ferricyanide,uric acid and dopamine were examined.The corresponding cyclic voltammetric data was showed that the electrochemical and electrocatalytic activities are depended on the nanotube length.The electrochemical reactivity of short MWNT(S-MWNT) is better than that of long MWNT(L-MWNT),which may be mainly attributed to the existence of …

Go to article

Mwnts Modified Gc Electrode For Hydrogen Peroxide Determination, Hong-Juan Wang, Chun-Mei Zhou, Hao Yu, Feng Peng, Jin-Kun Fang Feb 2007

Mwnts Modified Gc Electrode For Hydrogen Peroxide Determination, Hong-Juan Wang, Chun-Mei Zhou, Hao Yu, Feng Peng, Jin-Kun Fang

Journal of Electrochemistry

A MWNTs modified GC electrode was constructed successfully to be used to detect hydrogen peroxide.Two methods of maximum anodic current of cyclic voltommogram and chronoamperometry were adopted to measure the concentration of hydrogen peroxide.The results show that the MWCNTs can enlarge the effective surface area of GC electrode and can enormously enhance the electron transfer.The sensitivity and correlation coefficient for hydrogen peroxide detection are 2.84 μA/mmol·L-1,0.997 and 1.5 μA/mmol·L-1,0.971 for cyclic voltammetry and chronoamperometry,respectively.The procedure of the two methods to detect hydrogen peroxide is simple,and the results obtained are satisfied.

Go to article

Synergistic Functions Of Trimethl Phosphate And Vinylene Carbonate As Additives For The Li-Ion Batteries, Zhi-Yuan Tang, Yan-Bing He, Quan-Sheng Song, Yu-Hong Chen, Yuan-Gang Liu, Qiang Liu Nov 2006

Synergistic Functions Of Trimethl Phosphate And Vinylene Carbonate As Additives For The Li-Ion Batteries, Zhi-Yuan Tang, Yan-Bing He, Quan-Sheng Song, Yu-Hong Chen, Yuan-Gang Liu, Qiang Liu

Journal of Electrochemistry

The cooperative effects of trimethl phosphate and vinylene carbonate as additives for Li-ion batteries are investigated by using the cyclic voltammetry,electrochemical impedance spectroscopy and scanning electronic micro-photographs.The results show that the combination application of TMP and VC as additives for Li-ion batteries not only enhances safety of the batteries,but also improves their cycling performance.The reason may be ascribed to firstly VC being reduced and the reduction product polymerized to form excellent solid electrolyte interface(SEI) layer on the surface of graphite electrode during the first charge and discharge process,which prevents effectively the decomposition of TMP on the surface of the graphite …

Go to article

Facilitated Effect Of Ag To Oxygen Transportation In Pem Fuel Cell Air Cathodes, Hong-Feng Xu, Jian-Hua Dong, Xiang-Li Hou Nov 2006

Facilitated Effect Of Ag To Oxygen Transportation In Pem Fuel Cell Air Cathodes, Hong-Feng Xu, Jian-Hua Dong, Xiang-Li Hou

Journal of Electrochemistry

Silver(Ag) was deposited in the pores of Nafion membrane by ion exchange and succedent hydrogen reduction;the structures of Nafion-Ag membrane were measured by TEM and XRD,the diffusion coefficients of oxygen in Nafion-Ag was determined by electrochemical limited current method.The results showed that after deposited silver,the pores in the Nafion were enlarged by silver grains;the oxygen diffusion coefficient was increased about four times.By introducing silver in the thin Nafion film around the cathode catalyst,the performance of PEM fuel cell have a evident increasing in high current density, which shows the facilitated effects of silver to oxygen transportation in PEM fuel cell.

Go to article

Electrochemical Characterization Of Positive Electrode Material Lini1/3Co1/3Mn1/3O2 In Different Electrolytes, Jing-Jing Liu, Wei-Hua Qiu, Ling-Yan Yu, Hai-Lei Zhao, Tao Li Nov 2006

Electrochemical Characterization Of Positive Electrode Material Lini1/3Co1/3Mn1/3O2 In Different Electrolytes, Jing-Jing Liu, Wei-Hua Qiu, Ling-Yan Yu, Hai-Lei Zhao, Tao Li

Journal of Electrochemistry

Cathode materials LiNi1/3Co1/3Mn1/3O2 were prepared by low-heating solid-state reaction.The micro-structure and morphology of as-synthesized materials have been investigated by using XRD and SEM. The compatibilities of LiNi1/3Co1/3Mn1/3O2 with purchased LiPF6/ EC+DMC+DEC electrolyte and prepared LiBOB/EC+DEC+EMC electrolyte have also been studied. The Li/LiNi1/3Co1/3Mn1/3O2 batteries showed excellent electrochemical properties in the LiPF6/EC+DMC+DEC electrolyte. Reversible discharge capacities of 167, 163, 163, 157, 147mAh/g at 0.5C, 1C, 1.5C, 2C, 3C rate between 2.7~4.35 V, with stable cycling performances have …

Go to article

Electrochemical Behavior Of Buprofezin On Glass-Carbon Electrode, Qi Wang, Chang-Guo Chen Nov 2006

Electrochemical Behavior Of Buprofezin On Glass-Carbon Electrode, Qi Wang, Chang-Guo Chen

Journal of Electrochemistry

Electrochemical behavior of Bup has been investigated by means of cyclic voltammetry,linear sweep voltammetry,differential pulse voltammetry and square wave voltammetry.The results indicate that the electrochemical behavior of Bup on the surface of glassy carbon electrode is corresponding to a irreversible two-protons and two-electrons process with absrption.The square wave voltammetry for determination of Bup in actual samples has been established.

Go to article

Fabrication And Characterization Of Gadolinium Hexacyanoferrate Modified Electrode, Yan-Mao Shi, Pan Du, Ping Wu, Yao-Ming Zhou, Chen-Xin Cai Nov 2006

Fabrication And Characterization Of Gadolinium Hexacyanoferrate Modified Electrode, Yan-Mao Shi, Pan Du, Ping Wu, Yao-Ming Zhou, Chen-Xin Cai

Journal of Electrochemistry

A new electroactive polynuclear inorganic compound of rare earth metal hexacyanoferrate,gadolinium hexacyanoferrate(GdCHF),was prepared by electrochemically deposition on the surface of a glassy carbon electrode with a potential cycling procedure.The result of SEM indicated that the GdHCF was in the form of particles adhered on the surface of electrode.There were two different shapes and sizes of GdHCF forming on the surface of electrode.FTIR spectrum of GdHCF showed a very strong and sharp peak,which located at 2062.5 cm-1 and corresponded to the stretching vibration of the C≡N group in the GdHCF.The cyclic voltammetric results indicated that the GdHCF/GC electrode exhibited two …

Go to article

Synthesis Of Monolithic Carbon/Nickel Oxide Composite Electrode Material And Cyclic Voltammetry Characteristics, Tian-Ying Guo, Jing-Wei Zhu, Mou-Dao Song, Bang-Hua Zhang Nov 2006

Synthesis Of Monolithic Carbon/Nickel Oxide Composite Electrode Material And Cyclic Voltammetry Characteristics, Tian-Ying Guo, Jing-Wei Zhu, Mou-Dao Song, Bang-Hua Zhang

Journal of Electrochemistry

Monolithic carbon/nickel oxide composite materials were synthesized by carbonization of phenol formaldehyde gels that were ion-exchanged with Ni2+.Atomic absorption spectroscopy and powder X-ray diffraction technique were used to characterize the chemical composition and physical structure of the materials.The nickel dope amount for this method can reach 5.9 %(by mass).Subsequent cyclic voltammetry experiments indicate that the materials exhibit best capacitive performance at the nickel content of 4.4 %.

Go to article

Fabrication Of Gold Electrode Array Based On Co2 Laser Ablation, Wei Zhang, Jiang-Qun Xiao, Yong-Liang Zhou Nov 2006

Fabrication Of Gold Electrode Array Based On Co2 Laser Ablation, Wei Zhang, Jiang-Qun Xiao, Yong-Liang Zhou

Journal of Electrochemistry

A rapid process is described to produce single or multiple electrodes of any shape based on CO2 laser ablation for microfluidic chip.The method is as follow: coating a kind of material as sacrifice layer on a piece of glass with sputtered Cr and Au;designing the needed pattern on a computer;selecting proper parameters and ablating with CO2 laser;wiping of Au/Cr and sacrifice layer,and obtain electrodes at last.The microfluidic chip was gotten by reversely bonding with a piece of PDMS,and sealing around with PDMS prepolymer.The mask' effect is the main factor that influencing electrode quality.The width of electrodes could be …

Go to article

Novel Electrochemical Method For Synthesis Of Nanostructured Materials Of Noble Metals Based On Poly(N-Vinylpyrrolidone) (Pvp), Wei Pan, Xiao-Kai Zhang, Ming-Hu Huang, Shao-Xin Huang, Xing-Li Feng, Hou-Yi Ma Nov 2006

Novel Electrochemical Method For Synthesis Of Nanostructured Materials Of Noble Metals Based On Poly(N-Vinylpyrrolidone) (Pvp), Wei Pan, Xiao-Kai Zhang, Ming-Hu Huang, Shao-Xin Huang, Xing-Li Feng, Hou-Yi Ma

Journal of Electrochemistry

Gold nanocrystals with controllable size were synthesized through a simple electroreduction method using poly(N-vinylpyrrolidone)(PVP) of different polymerization degree as both stabilizer and shape-controller for gold nanoclusters.Individual gold nanoparticles spontaneously assembled into the wire-and ring-shaped nanoparticle aggregates depending on the PVP's dynamic stretching and curling,and precursor nanoparticles grew into flat,single-crystalline nanoprisms with thickness of dozens of nanometers based on the oriented aggregation between particles.Besides,core-shell Au/Ag nanoparticles were conveniently synthesized through two-step electroreduction of noble metal ions in the presence of PVPK30.The electrochemical synthetic method based on PVP provides a new path for preparation of noble metal nanostructured materials with different shape …

Go to article

Study Of The Electrooxidation Of Glycerol On Oxide And Pd/C Composite Catalysts, Zhi-Yuan Yan, Chang-Wei Xu, Pei-Kang Shen Nov 2006

Study Of The Electrooxidation Of Glycerol On Oxide And Pd/C Composite Catalysts, Zhi-Yuan Yan, Chang-Wei Xu, Pei-Kang Shen

Journal of Electrochemistry

Oxide and Pd on carbon composite catalysts have been prepared by intermittent microwave heating(IMH) method.The performance of the catalysts for glycerol oxidation in alkaline solution is studied by electrochemical techniques.It is shown that the Pd/C catalyst is active for glycerol electrooxidation.However,the oxide-Pd/C catalysts are even better in terms of the onset potential that is more negative and peak current density.The ratio of oxide to Pd is optimized according to the electrochemical measurement.The results reveal that the addition of oxide into the Pd/C induces the synergistic effect for glycerol electrooxidation.

Go to article

Deep Treatment Of Pulping Wastewater Using Three Phase Fluidized Bed Electrode Reactor, Dan Wu, Qi-Cai Shi, Ji-Ti Zhou, Bao-Jun Jia Nov 2006

Deep Treatment Of Pulping Wastewater Using Three Phase Fluidized Bed Electrode Reactor, Dan Wu, Qi-Cai Shi, Ji-Ti Zhou, Bao-Jun Jia

Journal of Electrochemistry

Treatment of pulping wastewater by using a novel electrochemical reactor,i.e.the three phase fluidized bed electrode,reactor were invesigated.The effects of air flow rate,applied voltage,pH value and FeSO4 concentration on electrolysis efficiency were investigated.It was clearly shown that the 20 V of voltage,0.3 m3·h-1 of air flow rate,1000 mg L-1 of FeSO4 concentration and pH≈2.5 were its best conditions.COD removal could be 70.1% under these conditions.

Go to article

Electrochemical Properties Of The Modified Carbon Nanotubes, Chun-An Ma Nov 2006

Electrochemical Properties Of The Modified Carbon Nanotubes, Chun-An Ma

Journal of Electrochemistry

Powder micro-electrodes were prepared from raw carbon nanotubes and carbon nanotubes modified by carboxyl.The electro-reduction properties of both the raw and open-ended carbon nanotubes in p-Nitrophenol solution were investigated.The FTIR spectrum result indicated that the functional groups are successfully fixed on the surface of the carbon nanotubes after nitric acid treatment.The cyclic voltammetry results show that the electrochemical activity of carboxyl-modified carbon nanotubes was improved.The mechanism of electro-(reduction) for the carbon nanotubes after acid treatment was discussed.

Go to article

Reaction Mechanism Of V(Ⅳ)/V(Ⅴ) Redox Couple At Graphite Felt Composite Electrode Bonded With Conductive Carbon Plastic, Xiao-Gang Li, Ke-Long Huang, Su-Qin Liu, Ning Tan, Li-Quan Chen Nov 2006

Reaction Mechanism Of V(Ⅳ)/V(Ⅴ) Redox Couple At Graphite Felt Composite Electrode Bonded With Conductive Carbon Plastic, Xiao-Gang Li, Ke-Long Huang, Su-Qin Liu, Ning Tan, Li-Quan Chen

Journal of Electrochemistry

The rate-determining step of V(Ⅳ) /V(Ⅴ) redoxreaction was investigated at graphite felt(GF)composite electrode by various techniques: cyclic voltammetry,polarization curve and impedance spectroscopy.Cyclic voltammetry analysis indicated that V(Ⅳ) /V(Ⅴ) redox reaction at GF electrode is quasi reversible.Acertain chemical reaction step is suspected to follow the electron transfer step of this reaction.The Tafel slopevalue(0.124) obtained from the polarization curve agrees well with theoretical value(0.12),which supposingthe electron transfer step was the rate-determining step.Impedance Spectroscopies at various potentials werestudied and simulated by equivalentcircuits.The impedance value of the electron transfer step modified is greatlyhigher than the others,which shows that the electron transfer step is the …

Go to article

The Synthesis, Structure And Electrochemical Performances Of Lithium Iron Phosphate, Hui Xie, Zhen-Tao Zhou Nov 2006

The Synthesis, Structure And Electrochemical Performances Of Lithium Iron Phosphate, Hui Xie, Zhen-Tao Zhou

Journal of Electrochemistry

The lithium iron phosphate cathode materials were synthesized by solid-state reaction combined high-rate ball milling under the temperature ranging from 400 ℃ to 700 ℃.The crystalline structure, morphology of particles, and electrochemical performance of the sample were investigated by X-ray diffraction, scanning electron microscopy and charge-discharge test. The results showed that the sintering temperature had great influences on the crystal structure, morphology and electrochemical performances of LiFePO4. The sample synthesized under 600℃ showed the best charge-discharge performances with the first specific discharge capacity of(128.8) mAh/g and the 15th specific discharge capacity of 129.1 mAh/g at 0.1C rate, …

Go to article

Structure And Electrochemical Characteristics Of Lifepo4 Prepared By The Polyacrylates-Pyrolysis-Reduction Method For Li-Ion Batteries, Li-Hong Yu, Yu-Liang Cao, Xiao-Fei Zhang, Han-Xi Yang, Xin-Ping Ai Nov 2006

Structure And Electrochemical Characteristics Of Lifepo4 Prepared By The Polyacrylates-Pyrolysis-Reduction Method For Li-Ion Batteries, Li-Hong Yu, Yu-Liang Cao, Xiao-Fei Zhang, Han-Xi Yang, Xin-Ping Ai

Journal of Electrochemistry

The cathode material of olivine LiFePO4 was prepared by a novel method of polyacrylate-pyrolysis-reduction.XRD demonstrates that the material have the olivine structure.SEM photo shows an average particle-size of about 100 nm with a well distribution.Electrochemical test of cycling at a constant current reveals the discharge capacity of 138 mAh/g and a good cycling stability.It is a novel practicable technology to prepare LiFePO4 by using polyacrylate-pyrolysis-reduction method.

Go to article

Research Of Explosion Mechanism Of Lithium-Ion Battery, Yu-Hong Chen, Zhi-Yuan Tang, Yan-Bing He, Qiang Liu Aug 2006

Research Of Explosion Mechanism Of Lithium-Ion Battery, Yu-Hong Chen, Zhi-Yuan Tang, Yan-Bing He, Qiang Liu

Journal of Electrochemistry

The heat character of Lithium-ion battery materials and explosion mechanism of Lithium-ion cells under the overcharge,short-circuit and other abuse behavior are tested by C80 calorimeter, DSC and charge-discharge instrument.SEI reactions, LixC6/electrolyte and LixC6/PVDF reactions take place at the anodes. Electrolyte and solvent reactions happen after 178℃ and Li1-xCo1/3Ni1/3Mn1/3O2 decomposes after 230℃. The batteries explode at 150℃ oven test or 1.5C, 5.5 V overcharge and do not explode at short-circuit.

Go to article

Immobilization Of Cytochrome C On The Surface Of Single-Wall Carbon Nanotube And Its Direct Electron Transfer And Electrocatalysis, Ya-Jing Yin, Ya-Fen Lv, Ping Wu, Pan Du, Yan-Mao Shi, Chen-Xin Cai Aug 2006

Immobilization Of Cytochrome C On The Surface Of Single-Wall Carbon Nanotube And Its Direct Electron Transfer And Electrocatalysis, Ya-Jing Yin, Ya-Fen Lv, Ping Wu, Pan Du, Yan-Mao Shi, Chen-Xin Cai

Journal of Electrochemistry

Cytochrome c(Cyto c) was immobilized on the surface of the single-wall carbon nanotube(SWNT) by using the method of adsorption.Infrared spectroscopy indicated that the Cyto c remained in its original structure and did not undergo structural change after its immobilization on the SWNT.The direct electrochemistry of cyto c,which was adsorbed on the surface of the SWNT,was studied by cyclic voltammetry.The voltammetric results demonstrated that the SWNT had promoting effects on the direct electron transfer of Cyto c and also indicated that the immobilized Cyto c retained its bioelectrocatalytic activity to the reduction of H2O2.This modified electrode might …

Go to article

Investigation Of The Direct Electrochemical Reduction Of Cr2O3 Powder In Molten Cacl2 By A Metallic Cavity Electrode, Guo-Hong Qiu, Di-Hua Wang, Xian-Bo Jin, Xiao-Hong Hu, Zheng Chen Aug 2006

Investigation Of The Direct Electrochemical Reduction Of Cr2O3 Powder In Molten Cacl2 By A Metallic Cavity Electrode, Guo-Hong Qiu, Di-Hua Wang, Xian-Bo Jin, Xiao-Hong Hu, Zheng Chen

Journal of Electrochemistry

A metallic cavity electrode is used for further investigation of the electrochemical behaviour of Cr2O3 powder in molten CaCl2(Na: ~0.02% by mass,Mg: < 0.005% by mass) at 900 ℃.The Cr2O3 powder reduction mechanism was confirmed in line with EDX and SEM analysis of the potentiostatic electrolysis products.The correlations between the particle size of metallised product and the electrolysis potential,or electrolysis time were analysed.

Go to article

Pre-Oxidative Amperometric Glucose Biosensor Incorporated With Carbon Nanotube And Pbo2, Hong-Lan Qi, Cheng-Xiao Zhang Aug 2006

Pre-Oxidative Amperometric Glucose Biosensor Incorporated With Carbon Nanotube And Pbo2, Hong-Lan Qi, Cheng-Xiao Zhang

Journal of Electrochemistry

A pre-oxidative amperometric glucose biosensor incorporated with carbon nanotube,ferrocenemonocarboxylic acid and PbO2 was designed.The interferences coming from reduced substances,such as ascoribic acid and urine acid were eliminated by PbO2.The oxidative current is linear at the potential of +0.40 V(vs.SCE) to the concentration of glucose in the range from 0.50 to 20 mmol·L-1,and the detection limit of glucose is 0.1 mol L-1.The relative standard deviation is 3.3% for seven successive assays at 5.0 mmol·L-1glucose.This biosensors have been applied to determination of the glucose in serum with satisfying results.

Go to article

The Influence Of Pva As Disperser On Lifepo4 Synthesized By Hydrothermal Reaction, Hui-Lin Li, Hui Zhan, Yu-Hong Zhou Aug 2006

The Influence Of Pva As Disperser On Lifepo4 Synthesized By Hydrothermal Reaction, Hui-Lin Li, Hui Zhan, Yu-Hong Zhou

Journal of Electrochemistry

LiFePO4 was synthesized by means of hydrothermal reaction,in which PVA acts as disperser and glucose as carbon source. The samples were characterized by X-ray diffraction, scanning electron microscopy and electrochemical measurement. SEM results show that the sample is homogeneously composed of grains with a particle size of ca.200nm. In the charge/discharge test, the products exhibited a 3.45V discharge voltage plateau and a maximum specific capacity of 140mAh/g. After 40 cycles, its capacity only declined by 2.1%. Besides these, the mechanism for the influence of the particle size and carbon coating on the electrochemical property of LiFePO4 material was …

Go to article

Calcined Temperatures Influence On Synthesis And Electrochemistry Charactarization Of Li[Ni0.475Mn0.475Co0.05]O2 For Li-Ion Batteries, Li-Qin Wang, Li-Fang Jiao, Hua-Tang Yuan, Yong-Mei Wang Aug 2006

Calcined Temperatures Influence On Synthesis And Electrochemistry Charactarization Of Li[Ni0.475Mn0.475Co0.05]O2 For Li-Ion Batteries, Li-Qin Wang, Li-Fang Jiao, Hua-Tang Yuan, Yong-Mei Wang

Journal of Electrochemistry

Layered Li[Ni0.475Mn0.475Co0.05]O2 materials have been prepared by a solid-state pyrolysis method.Experiments of XRD,SEM,cyclic voltammetry and charge/discharge cycling were carried out.It can be learned that when calclined at 800 ℃,the sample showed the highest first discharge capacity of 178.8 mAh·g-1 at a current density of 20 mA/g in the voltage range 2.3~4.6 V

Go to article

Investigation On The Resistance To Electrochemical Oxidation Of Carbon Nanotubes With Various Diameters, Yu-Yan Shao, Ge-Ping Yin, Yun-Zhi Gao, Peng-Fei Shi Aug 2006

Investigation On The Resistance To Electrochemical Oxidation Of Carbon Nanotubes With Various Diameters, Yu-Yan Shao, Ge-Ping Yin, Yun-Zhi Gao, Peng-Fei Shi

Journal of Electrochemistry

The resistance to electrochemical oxidation of multi-wall carbon nanotubes(CNT) with various diameters is investigated by applying a fixed potential of 1.2 V(RHE) for 120 h in 0.5 mol L-1 H2SO4.The oxidation current of CNTs decreases with their diameters,but CNTs between 10~20 nm in diameter(D1020) shows the lowest oxidation current.XPS analysis shows that,after oxidation,the increase in surface oxygen for D1020 is the smallest,implying that the oxidation degree for D1020 is the lowest.The conclusion can be reached that CNTs between 10~20 nm in diameter are the most resistant to electrochemical oxidation.The difference in electrochemical stability of CNTs …

Go to article

Preparation And Supercapacitor Properties Of Yttrium Doped Nio, Dan-Dan Han, Ye Chen, Mi-Lin Zhang, Chang Shu, Chun-Xia Zhang, Peng-Cheng Xu Aug 2006

Preparation And Supercapacitor Properties Of Yttrium Doped Nio, Dan-Dan Han, Ye Chen, Mi-Lin Zhang, Chang Shu, Chun-Xia Zhang, Peng-Cheng Xu

Journal of Electrochemistry

Yttrium doped Nano-NiO were synthesized by chemical precipitation method.Characterization and performance of the samples were studied by X-ray diffraction,the results showed that the doping Yttrium did not change the crystal structure of NiO,but the size of crystalline grain was reduced.The electrochemical properties of the electrode materials were measured in the three electrode system.Electrochemical properties of NiO were researched by cyclic voltammetry,constant current charge/discharge and AC impedance methods.It could be seen that the chemical doping improved the specific capacitance and the utilization of active materials.When the weight ratio of NiO with Y2O3was 1∶0.1,the composite material had the …

Go to article

Study On The Preparetion And Electrochemical Beavior Of Nitrogen Doped Tetrahedral Amorphous Carbon Electrode, Ke Liu, Guang-Fu Wang, Zheng-Hao Wang Aug 2006

Study On The Preparetion And Electrochemical Beavior Of Nitrogen Doped Tetrahedral Amorphous Carbon Electrode, Ke Liu, Guang-Fu Wang, Zheng-Hao Wang

Journal of Electrochemistry

taC∶N films are a good materials for semiconductor electrodes.But further studies are hampered by the ohmic contact problem,which occurs between the silicon and the lead.By studying the influence of heat treatment on the film's property,it is believed that ohmic contact should be made on the silicon first,and then the film be deposited.A set of taC∶N electrodes with various nitrogen content have been prepared.CV study indicates that the cathodic limits move slowly to positive direction.while the anodic limits are unchanged with the increasing of nitrogen content.As a result,the electrochemical windows get narrow either.

Go to article

Electrodeposition Of Nano-Sb-Zn Alloy In Acetamide-Urea-Nabr-Kbr Melt, Peng Liu, Xin-Ai Guo, Ye-Xiang Tong, Qi-Qin Yang Aug 2006

Electrodeposition Of Nano-Sb-Zn Alloy In Acetamide-Urea-Nabr-Kbr Melt, Peng Liu, Xin-Ai Guo, Ye-Xiang Tong, Qi-Qin Yang

Journal of Electrochemistry

The electroreduction of Zn(II) and Sb(III) in acetamide-urea-NaBr-KBr(343 K) were studied by cyclic volatmmetry.The reduction of Zn(II) or Sb(III) to the metals is an irreversible process.The transfer coefficient of Zn(II)+2e→Zn and Sb(III) +3e→Sb were calculated to be 0.231 and 0.319,the diffusion coefficient of Zn(II) and Sb(III) in the melt were determined as 1.70*10-6 and 3.21*10-6 cm2· s-1 respectively.The Zn-Sb films with different Zn content from 29.67 at% to 97.34 at% were electrodeposited in acetamide-urea-NaBr-KBr melt at 343 K by controlling the deposition potential and the Zn(II)/Sb(III) molar ratio.The morphology of Zn-Sb film was observed by …

Go to article

Influence Of Crystallinity On The Kinetics Of Li Ion Insertation And Deinsertation In Spinel Limn2O4, Rong-Hua Zeng, Dong-Sheng Lv, Wei-Shan Li Aug 2006

Influence Of Crystallinity On The Kinetics Of Li Ion Insertation And Deinsertation In Spinel Limn2O4, Rong-Hua Zeng, Dong-Sheng Lv, Wei-Shan Li

Journal of Electrochemistry

Two spinel lithium manganese oxides of different crystallinity were prepared by sol-gel process and were studied by using inducfively coupled plasma,X-ray diffraction,scaning electron micrographs,constant charging and discharging,cyclic voltammetry and electrochemical impedance spectrometry,the results show that the sample treated under 700 ℃ has higher crystallinity than the sample treated under 500 ℃,however,the sample with lower crystallinity has higher discharge capacity and better cyclic performance that due to quicker charge exchange speed and quicker diffusion speed of Li-ion.

Go to article

First Prev Next Last