Materials Science and Engineering Commons^™

Some Effects Of Oh Groups On Sodium Silicate Glasses, Mokhtar Sayed Maklad

Doctoral Dissertations

"Glasses of various compositions in the Na₂O-SiO₂ system were prepared with different levels of OH concentration. Phase separation kinetics, thermal expansion, radiation induced optical absorption, and internal friction of these glasses were studied. The increase in OH content in these glasses was found to (a) enhance the rate of phase separation; (b) increase thermal expansion above the glass temperature and change the dilatometric softening temperature in a way that depends on microstructure; (c) increase the radiation induced optical absorption bands associated with positive hole centers and decrease those associated with electron trap centers; and, (d) decrease the low temperature alkali …

Electrode Reactions In Zinc Electrolysis, Ernest R. Cole

Doctoral Dissertations

"The effects of temperatures from 0°C to 50°C and current densities from 10 asf to 200 asf on the current efficiency in the electrolysis of pure zinc sulfate solutions (65 gpl Zn⁺⁺ - 200 gpl H₂SO₄) were determined. Pure platinum and platinum coated titanium anodes were used with an aluminum cathode. Platinum anodes were not inert at certain combinations of temperature and current density, and platinum acted as a low overvoltage impurity causing resolution of the cathode deposit. Orientation of the zinc deposits was found to vary with temperature and to have a distinct relationship to current efficiency. Preconditioning of …

Voids In Neutron Irradiated Aluminum, Nicholas H. Packan

Doctoral Dissertations

"Void formation in high purity aluminum resulting from irradiation to fluences between 1.5 x 10¹⁹ and 1.6 x 10²² neutrons/cm² (E > 0 .1 MeV) at a temperature of 55 ± 5ºC was studied, primarily by means of transmission electron microscopy. In particular the effects of neutron fluence and flux were examined, as well as the possible influences of both preexisting and transmutation-produced impurities. A very low concentration of voids (about 10¹²/cm³) resulted from irradiation to 1.5 x 10¹⁹ neutrons/cm²; they averaged about 150 Å in diameter. Void concentrations and sizes increased with fluence, reaching values of 6 x 10¹⁴ voids/cm³ …

Temperature Variation In Distribution Of Relaxation Times In Aluminosilicate Glasses, David Wayne Moore

Doctoral Dissertations

"The distribution of relaxation times for the alkali peak in a Li₂ O·A1₂O₃ ·2.0SiO₂ glass and for the mixed alkali peak in a 0.5Li₂O·0.5Na₂O·A1₂O₃·2.OSiO₂ glass was studied using the internal friction technique. A lognormal distribution of relaxation times provided the best agreement with the experimental data. The ß parameter of the lognormal distribution function, which is related to the half-height peak width, varied with temperature, indicating that the distribution of relaxation times is dependent upon the activation energy and the activation entropy of the relaxation mechanism. The major contributor to the distribution of relaxation times is a wide distribution in …

Diffusion Of Iron And Cobalt In Nickel Single Crystals, Charles Frederick Heuer

Doctoral Dissertations

"Diffusion coefficients of iron-59 in nickel have been determined in the temperature range 815°C to 1200°C. The temperature dependence can be represented by an Arrhenius type relationship,...The effect of the isotopic mass on the diffusion coefficient of cobalt in nickel has also been investigated. The isotope effect parameter, E, was found to vary from .26 to .84 over the temperature range 970.5°C to 1200°C. Both results are consistent with the single vacancy mechanism of diffusion. No evidence of divacancy contributions to the mass transport has been found"--Abstract, Page i.

A Crystallization Study Of A Tetrasilicic Fluormica Glass, William H. Daniels

Doctoral Dissertations

"The transformation of a synthetic mica composition K₂Mg₅Si₈O₂₀F₄ from amorphous to crystalline structure was studied isothermally at selected temperatures from 560°C to 1150°C. thermal changes associated with the transformation were followed by differential thermal analysis techniques. Structural changes promoted by the isothermal treatments were observed by density measurements, Debye-Scherrer X-ray diffraction techniques, electron replication microscopy, and electron scanning microscopy. Isothermal treatment at 450°C for 9 hours produces structural ordering in quenched K₂Mg₅Si₈O₂₀F₄ glass. Fluorine exerts a significant influence on the transformation temperature; decreasing amounts of fluorine producing increasing transformation temperatures. The crystallizing phase rapidly attains a limiting particle size and …

Grain Boundary Self-Diffusion In Sodium Chloride, Kenneth Ray Riggs

Doctoral Dissertations

"The diffusion of ²²sodium and ³⁶chlorine along tilt and twist grain boundaries in pure and calcium chloride doped sodium chloride bicrystals was investigated. No enhanced diffusion of ²²sodium along the grain boundaries was observed. Between 400°C and 500°C the chlorine grain boundary diffusion parameter, D'Δ, is described by D'Δ = (D'Δ)₀exp (-Q_b/kT), where (D'Δ)₀ is approximately 10⁻⁷ cm³/sec and Qb is 1.15 ± .30 eV. The grain boundary angle, the grain boundary character (tilt or twist), and the calcium chloride concentration appear to have no pronounced effect upon the observed chlorine grain boundary diffusion. The ionic movement …

The Iron-Holmium Binary System And Related Magnetic Properties, Gerald J. Roe

Doctoral Dissertations

"The iron-holmium phase diagram was investigated to determine the alloying behavior of these two metals and to determine the magnetic properties of some of the iron-holmium alloys which formed intermediate phases. The iron-holmium binary system was determined by three experimental techniques, differential thermal analysis (DTA), x-ray diffraction, and metallography. A phase diagram with three eutectic points and four intermediate phases was constructed from the experimental data. The two phases, Ho₆Fe₂₃ and Ho₂Fe₁₇, melted congruently at 1322⁰C and 1343⁰C respectively. HoFe₂ and HoFe₃ melted incongruently at 1288⁰C and 1293⁰C respectively. Neutron diffraction investigations were made on the intermediate phases Ho₆Fe₂₃ and …

Calorimetry Of Room Temperature Deformed Copper, George Juri Filatovs

Doctoral Dissertations

"An adiabatic anisothermal differential calorimeter for the study of room temperature deformed 99.999% pure copper has been constructed. An annealed and a deformed specimen were heated at a constant rate in adiabatic surroundings and the differences in energy released between samples was obtained. The control circuits were automatic. Deformation was by elongation ranging from 12 to 40%, and the corresponding energy found was from 1.9 to 5.3 calories/gram-atom. No recovery energy was found. The results obtained generally agree with published results and, in particular, verify Gordon's isothermal annealing results. It is proposed that the criteria for the presence of recovery …

Phase Equilibria And Thermodynamic Studies In The System Ca0-Fe0-Fe₂0₃₋Si0₂, Muharrem Timucin

Doctoral Dissertations

"A study of phase relations and thermodynamic properties of phases in the system CaO-FeO-Fe₂O₃-SiO₂ was conducted at 1450°C and 1550°C. The region of stability of the different phases was determined by microscopic examination of the specimens. The thermodynamic properties of liquid were determined by analyses of quenched samples equilibrated at oxygen pressures from about 10⁻¹¹ to 1 atm. Isothermal phase diagrams were constructed from data for 0, 5, 10, 20, and 30 weight percent silica sections of the CaO-FeO-Fe₂O₃-SiO₂ system, and the effect of temperature and increased silica additions on the oxygen solubility of the liquid oxides was measured. Multicomponent …

X-Ray Determination Of Lattice Parameters And Thermal Expansion Coefficients Of Aluminum, Silver And Molybdenum At Cryogenic Temperatures, Claude Lowell Woodard

Doctoral Dissertations

"A multiple exposure back reflection diffraction camera was designed to mount on the vacuum jacket of a pressurized helium gas "Cryomite". With this design it is possible to obtain six diffraction exposures on a single film at any temperature in the range of 180 to 25°K. temperatures within this range are reached in short intervals and exposure periods are less than 30 minutes in a 2.875 inch (73.03 mm) diameter camera. Some of the advantages of this design are; direct measurements, multiple exposures on a single film, short exposures, direct compensation of film length changes due to evacuation or processing …

The Damage Assessment Of Thermally Shocked High Density, High Purity Aluminum Oxide, John H. Ainsworth

Doctoral Dissertations

"The traditional approach to thermal shock testing in brittle materials has been to determine the temperature difference required to nucleate cracks in these materials. Recent work has indicated that the degree of damage after crack nucleation should be an additional consideration. The degree of damage resulting from cooling thermal shocks has been the primary consideration of the present work. Test specimens of two geometries: long, solid rods and short, solid cylinders were quenched from selected temperatures into ice water. The degree of damage was determined through strength measurements and sonic damping analysis. Initial damage occurred at a temperature difference above …

Decomposition Of Cr(Oh)₃ To Form Active Cr₂C₃, Timothy A. Clancy

Doctoral Dissertations

"This study was concerned with the sinterability of Cr₂C₃ powders produced by the calcination of a Cr(OH)₃ gel. The decomposition of the gel was investigated by thermogravimetric analysis, X-ray analysis and microscopic examination. Comparison was made between the size of crystallites as determined by X-ray line broadening and the size of aggregated particles as determined by independent means. These lineal measurements were compared to surface area measurements on the calcined powders. The degree of sinterability was judged from the density measurements on Cr₂C₃ pellets fired under air, oxygen and nitrogen atmospheres. Energies of activation of 25 and 20 kilocalories per …

Effect Of Micelles On Flotation Of Metal Ions, Uriel Michael Oko

Doctoral Dissertations

"A study of the anionic surfactant, sodium dodecyl sulfate (SDS), and the dependency of the adsorption of divalent metal counterions such as copper and zinc at the air-water interface on its concentration in the solution, was undertaken in order to better understand the process of ion flotation. The study is divided into two broad categories, the first of which consists of the evaluation of the extent of aggregation of the surfactant molecules into micelles, and the effect of the divalent metal counterion concentration on this aggregation and on the critical concentration at which micelles start forming (cmc). This was accomplished …

Surface Self-Diffusion On Nickel (111) By Radioactive Tracers, James Ronald Wolfe

Doctoral Dissertations

"Surface self-diffusion coefficients have been measured by a radioactive tracer method over the temperature range 614⁰ to 840⁰C on nickel (111) surfaces characterized by LEED. Previously unrecognized tracer evaporation during surface diffusion resulted in restricted spreading of the tracer at higher temperatures. A theoretical treatment of the tracer evaporation phenomenon is presented and subsequently used in the analysis of the data. The temperature dependence of the surface self-diffusion coefficient (D_s) for nickel (111) can be represented, over the experimental temperature range, by a single Arrhenius type relationship...Arguments are presented to justify an adatom surface diffusion mechanism which is …

Optical Reflectance Spectra Of Chromium (Iii) In Mgo-Ss, Thomas Spencer Montgomery

Doctoral Dissertations

"The valence state and coordination site of the transition-metal ion, chromium, was investigated in a MgO host lattice. The chromium ion incorporated into poly-crystalline MgO by quenching from elevated temperatures allowed investigation of a single crystalline phase, MgO-solid solution (ss). The chromium ion was confirmed to occur in the trivalent state and to occupy octahedral cation sites in the MgO lattice by the use of optical reflectance spectroscopy. The effect of the concentration of the chromium ion on the crystal field splitting energy, 10 Dq, permitted analysis over a range of Dq/B values. In conjunction, MgO-ss lattice parameters examined as …

An Investigation Of The Induction Heating Characteristics Of Powdered Susceptors Dispersed In A Non-Conducting Medium, Robert Leon Wright

Doctoral Dissertations

"This investigation determined some of the induction heating characteristics of powdered magnetite, iron and ferrosilicon susceptor dispersed in silica sand which had been coated with thermosetting resin. The powdered susceptor particles in the mixture were heated by the field of an induction coil, consequently heating the resin coated sand and bonding the sand grains together.

It was found that the type, relative amount,and particle size of the susceptor were important variables to be considered in the induction heating characteristics. Hysteresis losses in the susceptor particles, which are a function of the coil current, frequency, and permeability, appear to be the …

Hydrogen Absorption And Corrosion Studies Of Zone-Refined Iron, Chang Don Kim

Doctoral Dissertations

"The lattice constants of zone-refined iron filings and iron whiskers are 2.86623 and 2.86626 Å at 25°C respectively. Their thermal expansion coefficients are both the same, 12.1 x 10⁻⁶ /°C at temperatures 10 - 65°C.

The influence of hydrogen on the lattice constant of iron was investigated and it was found that hydrogen has no effect (within the limits of errors) on the lattice constant of iron at room temperature regardless of the charging methods. However, at elevated temperatures hydrogen expands the iron lattice due to increased solubility of the gas. The lattice constant of iron in vacuum and in …

The Statistical Mechanics Of Kink Interactions, Michael Brewer Mcneil

Doctoral Dissertations

"Using a potential derived from continuum elasticity, the interactions between kinks on a dislocation line are studied as special cases of the problem of a one-dimensional system of interacting particles. By the use of constant pressure ensembles, the principal kink-interaction problems of physical interest are solved. The application of these solutions to the theoretical analyses of work hardening and internal friction is explored and comparisons made to previous work in which kink interactions were neglected; it is found that, as would be expected, variations of equilibrium kink populations with external stress cannot account for the Bordoni peak, which must therefore …

Internal Friction Of Mixed-Alkali Silicate Glasses, James E. Shelby

Doctoral Dissertations

"The mixed alkali effect in silicate glasses was examined from internal friction measurements made over the temperature range from -190 to 500⁰C and at a frequency of 0.4 Hz. Supplemental measurements of the activation energy for the different internal friction peaks, dynamic shear modulus, density, and index of refraction were also made. All measurements were confined to silicate glasses containing mixtures of Li-Na, Li-K, Li-Rb, Li-Cs, Na-K, Na-Rb, Na-Cs, and K-Rb. Rötger's interpretation of the internal friction of mixed-alkali silicate glasses is shown to be incorrect. A previously unreported internal friction peak was observed whenever two different alkali oxides were …

The Thermodynamics Of The Zno-Fe₂O₃-Fe₃O₄ System, Robert Lee Benner

Doctoral Dissertations

"The purpose of this investigation was to (1) experimentally locate certain phase boundaries in three isothermal sections of the zinc oxide - ferric oxide - magnetite phase diagram, (2) to experimentally determine some of the thermodynamic properties of the zinc oxide - ferric oxide - magnetite system, (3) to use the thermodynamic properties of the zinc oxide - ferric oxide - magnetite system to evaluate the pseudo-binary system between zinc ferrite and magnetite, (4) to construct a compound stability diagram for the zinc-iron-oxygen-sulfer system"--Introduction, Statement of the Problem, page [1].

Mechanism Of Siliconizing Of Molybdenum And Tantalum By Vapor Deposition, Gordon Pu Kong Chu

Doctoral Dissertations

"Molybdenum and tantalum were siliconized in an enclosed system by the hydrogen reduction of silicon tetrachloride with induction heating between 900°C and 1450°C.

The siliconizing process was primarily influenced by the gaseous composition, temperature, time, molar flow ratio (SiCl₄/H₂), geometrical shape and ionization charges. The rate of siliconizing, measured as the weight gain by the fused quartz helix balance, generally follows a parabolic law, y = k t^1/2, where y = weight gain, t = time, and k = rate constant. The activation energy is estimated at 21.6 k cal/mole for siliconizing of molybdenum. …

Lattice Parameters, Thermal Expansion Coefficients, Densities, And Imperfections In Silver And In The Alpha-Phase Of The Silver-Indium System, Samir Moustafa Riad

Doctoral Dissertations

“An investigation of structure insensitive properties (lattice parameters, thermal expansion coefficients, densities, and imperfections) of silver and the α-phase of the silver-indium system was suggested by the desirable uses for silver and its indium alloys.

Both silver and indium used were 99.999 per cent pure. The silver-indium alloys were prepared by melting both metals inside evacuated and sealed fused quartz tubes. The solidified alloys were annealed and then examined by X-ray diffraction for homogeneity.

This experimental work is divided into three main parts:-

I. X-ray diffraction investigation to determine the solid solubility limit of the Ag-In α-phase at 25° C, …

A Thermodynamic Study Of The Zirconium-Sulfur, Titanium-Sulfur And Hafnium-Sulfur Systems In The Disulfide-Trisulfide Region, Norbert Achilles Vermaut

Doctoral Dissertations

"A static method was used to study the equilibria which exist between the higher sulfides of zirconium and sulfur at temperatures from 700° to 1000 °C. Both disulfide and trisulfide have been identified by chemical analysis and X-ray diffraction. There exists a two-phase region of 'ZrS₂' and 'ZrS₃'. The composition limit of the homogeneous disulfide phase appears to exist between ZrS_1.90 and ZrS_2.00. The lower composition limit of the homogeneous region of the trisulfide phase was established as ZrS_2.75.

An experimental method of Blitz and co-workers, i.e., the use of evacuated …

An Investigation Of The Deformation Textures Of Cobalt, Roy Carl Wilcox

Doctoral Dissertations

"Deformation textures of various cobalt structures as a result of cold rolling together with some annealing textures were studied. The textures of cobalt were determined using a modification of the Schulz-Decker Geiger counter technique. Pole figures of the (1011), (0001) and (1010) planes were constructed. Also, a study of the microhardness of cobalt was made.

Microhardness tests were performed on various cobalt structures, in both the cold rolled and unworked conditions. The microhardness was found to vary with the source of the cobalt, the crystal orientation, and the amount of deformation and twinning. Deformation lines about the hardness impressions diffused …

Statistical Analysis Of Fracture Stresses Of Triaxial Porcelain Bodies, Robert E. Moore

Doctoral Dissertations

"Triaxial porcelain bodies containing various forms of silica, quartz, cristobalite and fused silica, were strength tested in bending. Significance tests were employed to discern real differences in the strength sample statistics caused by the various forms of silica. Firings were performed at three temperature levels. The differences in strength sample statistics were correlated to the microstructures of these silica porcelains.

A triaxial alumina porcelain body was employed as a model brittle solid for a study of the effect of flaw density on mean fracture stress. The flaws were introduced in the form of large diameter (d̄ = 115 microns) rounded …

A Study Of The Recrystallization And The Mechanical Properties Of Indium, Louis John Reitsma Jr.

Doctoral Dissertations

"The recrystallization temperature and the mechanical properties of tensile strength, elongation, reduction in area and hardness were determined for 99.97% indium. Metallographic techniques were developed and stress rupture data were obtained.

Single crystals of indium were grown in a horizontal furnace with a traveling temperature zone, and sectioned in a strain-free manner, with an etch-cutter. Because of the low recrystallization temperature of indium, no further work was done on the single crystals.

The effect of recrystallization on electrical resistance, thermoelectric force, hardness, bending strength, crystallographic orientation and microstructure was studied. The range of recrystallization temperature for small amounts of cold …

A Thermodynamic Study Of The Zirconium Sulfides, Andrew Hessler Larson

Doctoral Dissertations

"A hydrogen reduction technique was used to determine some thermodynamic properties of various zirconium sulfide phases. The equilibrium H₂S/H₂ ratios were determined as a function of temperature and composition of the condensed sulfide phases. The hydrogen sulfide content of the equilibrated gas mixtures was analyzed by an iodimetric titration procedure.

A detailed description is given for the method and apparatus used both in the preparation of the various sulfide phases and in their equilibration with a hydrogen-hydrogen sulfide gas mixture.

The composition ranger 59 to 67 atomic per cent sulfur was studied over a temperature range of …

Imperfections Within Ti₂O₃ And Tio₂ Phases In The Titanium-Oxygen System, Tatsuhiko Ejima

Doctoral Dissertations

“The hexagonal-rhombohedral Ti₂O₃ phase in the Ti-O system extends from 32.5 to 34.5% oxygen b.w., with the exact composition of Ti₂O₃ nearly in the middle of the phase. Seven samples of different composition within that phase were made, and the lattice constants (a and c) and the density of each sample were determined.

The plots of the constants against the composition of the samples revealed a deviation from Vegard’s rule when approaching the exact composition of Ti₂O₃. The lattice constants of this compound, obtained by graphical interpolation were; a_{25 …}

A Thermodynamic Study Of The Titanium Sulfides, Reinhard Paul Abendroth

Doctoral Dissertations

"The determination of the thermodynamic properties of chemical compounds is in essence an experimental one. The purpose of this investigation was (1) to make an experimental determination of the thermodynamic properties of the titanium sulfides (2) to determine what sulfide phases are present in the titanium-sulfur system (3) to show the relationships between the various phases present"--The Problem, Statement of the Problem, page 3.