Materials Science and Engineering Commons^™

Continuous Ultra-Thin Mos2 Films Grown By Low-Temperature Physical Vapor Deposition, Christopher Muratore, Jianjun Hu, Baoming Wang, M. Amanul Haque, John E. Bultman, Michael L. Jespersen, Michael E. Mcconney, R. D. Naguy

Chemical and Materials Engineering Faculty Publications

Uniform growth of pristine two dimensional (2D) materials over large areas at lower temperatures without sacrifice of their unique physical properties is a critical pre-requisite for seamless integration of next-generation van der Waals heterostructures into functional devices. This Letter describes a vapor phasegrowth technique for precisely controlled synthesis of continuous, uniform molecular layers of MoS2 on silicon dioxide and highly oriented pyrolitic graphite substrates of over several square centimeters at 350 °C. Synthesis of few-layer MoS2 in this ultra-high vacuum physical vapor deposition process yieldsmaterials with key optical and electronic properties identical to exfoliated layers. The films are composed of …

Optical Properties Of Carbon Microcoils, Muneaki Hikita, Li Cao, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

Carbon microcoils (CMCs) have emerged as versatile material artifacts for a variety of applications due to their helical and spiral structures. Embedded in matrix, CMCs have already been demonstrated for their potential tactile/proximity sensor application. In this study, CMCs were prepared using a conventional chemical vapor deposition method, and then were functionalized with octadecylamine.

Upon photoexcitation, the functionalized CMCs exhibited photoluminescence in the visible region, which has never been found before. Similar to carbon based nanoparticles, the photoluminescence of CMCs was attributed to electron-hole radiative recombination after surface passivation. The results suggested that this kind of fluorescent functionalized CMCs might …

Domain Engineering Of Physical Vapor Deposited Two-Dimensional Materials, Tarek Alam, Baoming Wang, Raghu Pulavarthy, M. Amanul Haque, Christopher Muratore, Nicholas R. Glavin, Ajit K. Roy, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

Physical vapor deposited two-dimensional (2D) materials span larger areas compared to exfoliated flakes, but suffer from very small grain or domain sizes. In this letter, we fabricate freestanding molybdenum disulfide (MoS2) and amorphous boron nitride (BN) specimens to expose both surfaces. We performed in situ heating in a transmission electron microscope to observe the domain restructuring in real time. The freestanding MoS2 specimens showed up to 100× increase in domain size, while the amorphous BN transformed in to polycrystalline hexagonal BN (h-BN) at temperatures around 600 °C much lower than the 850–1000 °C range cited in the literature.

Less Is More: Long-Term In Vitro Exposure To Low Levels Of Silver Nanoparticles Provides New Insights For Nanomaterial Evaluation, Kristen K. Comfort, Laura K. Braydich-Stolle, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

In view of the vast number of new nanomaterials (NMs) that require testing and the constraints associated with animal models, the majority of studies to elucidate nanotoxicological effects have occurred in vitro, with limited correlation and applicability to in vivo systems and realistic, occupational exposure scenarios.

In this study, we developed and implemented a chronic in vitromodel coupled with lower, regulatory dosages in order to provide a more realistic assessment of NM-dependent consequences and illuminate the implications of long-term NM exposure. When keratinocytes were exposed to 50 nm silver nanoparticles (Ag-NPs), we determined that chronically dosed cells operated …

Physiological Fluid Specific Agglomeration Patterns Diminish Gold Nanorod Photothermal Characteristics, Kristen K. Comfort, Jared W. Speltz, Bradley M. Stacy, Larry R. Dosser, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

Investigations into the use of gold nanorods (Au-NRs) for biological applications are growing exponentially due to their distinctive physicochemical properties, which make them advantageous over other nanomaterials. Au-NRs are particularly renowned for their plasmonic characteristics, which generate a robust photothermal response when stimulated with light at a wavelength matching their surface plasmon resonance. Numerous reports have explored this nanophotonic phenomenon for temperature driven therapies; however, to date there is a significant knowledge gap pertaining to the kinetic heating profile of Au-NRs within a controlled physiological setting. In the present study, the impact of environmental composition on Au-NR behavior and degree …

A Tensile Deformation Model For In-Situ Dendrite/Metallic Glass Matrix Composites, J. W. Qiao, T. Zhang, Fuqian Yang, P. K. Liaw, S. Pauly, B. S. Xu

Chemical and Materials Engineering Faculty Publications

In-situ dendrite/metallic glass matrix composites (MGMCs) with a composition of Ti₄₆Zr₂₀V₁₂Cu₅Be₁₇ exhibit ultimate tensile strength of 1510 MPa and fracture strain of about 7.6%. A tensile deformation model is established, based on the five-stage classification: (1) elastic-elastic, (2) elastic-plastic, (3) plastic-plastic (yield platform), (4) plastic-plastic (work hardening), and (5) plastic-plastic (softening) stages, analogous to the tensile behavior of common carbon steels. The constitutive relations strongly elucidate the tensile deformation mechanism. In parallel, the simulation results by a finite-element method (FEM) are in good agreement with the experimental findings and theoretical calculations. The present study gives a mathematical model to clarify …

The Biological Impact Of Concurrent Exposure To Metallic Nanoparticles And A Static Magnetic Field, Kristen K. Comfort, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

The rapid advancement of technology has led to an exponential increase of both nanomaterial and magnetic field utilization in applications spanning a variety of sectors. While extensive work has focused on the impact of these two variables on biological systems independently, the existence of any synergistic effects following concurrent exposure has yet to be investigated. This study sought to ascertain the induced alterations to the stress and proliferation responses of the human adult low calcium, high temperature keratinocyte (HaCaT) cell line by the application of a static magnetic field (approximately 0.5 or 30 mT) in conjunction with either gold or …

On Electric Conduction Of Amorphous Silicon Carbonitride Derived From A Polymeric Precursor, Yaohan Chen, Fuqian Yang, Linan An

Chemical and Materials Engineering Faculty Publications

A long-existing problem that the conductivity of amorphous silicon carbonitrides derived from polymeric precursor increases significantly with pyrolysis temperature is investigated. We show that the conductivity exhibited an Arrhenius dependence on pyrolysis temperature, with the activation energy of ∼3.41 eV. Structural analysis using Raman spectroscopy reveals that the free carbon within the material undergoes a sp³-to-sp² transition as pyrolysis temperature increases, with the activation energy of ∼3.6 eV. We conclude that the pyrolysis-temperature induced increase in the conductivity is mainly due to the increase in the conductivity of the free carbon. A simple model is proposed to …

Study Of An Alternative Process For Oxidizing Vapor Grown Carbon Nanofibers Using Electron Beam Accelerators, Maria Cecília Evora, Donald A. Klosterman, Khalid Lafdi, Lingchuan Li, L.G.A. Silva

Chemical and Materials Engineering Faculty Publications

The use of a high-energy electron beam was explored in this study as an alternative technique for oxidizing vapor grown carbon nanofiber surfaces. The radiation exposures were carried out at three different electron beam facilities with beam energies of 1.5, 3.0 and 4.5 MeV and radiation doses ranging from 1000 to 3500 kGy. XPS analysis showed that oxygen was readily incorporated on the surface: the ratio O1s/C1s increased approximately by a factor of 4 when the carbon nanofibers were irradiated at 3500 kGy. The oxidized nanofibers exhibited better dispersion in a water/methanol solution (50% v/v) than as-received nanofibers. Raman spectroscopy …

Infrared Optical Properties Of Amorphous And Nanocrystalline Ta2o5 Thin Films, Trevor J. Bright, J. I. Watjen, Zhuomin Zhang, Christopher Muratore, Andrey A. Voevodin, D. I. Koukis, David B. Tanner, Daniel J. Arenas

Chemical and Materials Engineering Faculty Publications

The optical constants of tantalum pentoxide (Ta 2O5) are determined in a broad spectral region from the visible to the far infrared. Ta 2O5 films of various thicknesses from approximately 170 to 1600 nm aredeposited using reactive magnetron sputtering on Si substrates. X-ray diffraction shows that the as-deposited films are amorphous, and annealing in air at 800 °C results in the formation of nanocrystallineTa 2O5. Ellipsometry is used to obtain the dispersion in the visible and near-infrared. Two Fourier-transform infrared spectrometers are used to measure the transmittance and reflectance at wavelengths from 1 to 1000 μm. The surface topography and …

Cross-Plane Thermal Properties Of Transition Metal Dichalcogenides, Christopher Muratore, Vikas Varshney, Jaime J. Gengler, Jianjun Hu, John E. Bultman, Timothy M. Smith, Patrick J. Shamberger, Bo Qiu, Xiulin Ruan, Ajit K. Roy, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

In this work, we explore the thermal properties of hexagonal transition metal dichalcogenide compounds with different average atomic masses but equivalent microstructures. Thermal conductivity values of sputtered thin films were compared to bulk crystals. The comparison revealed a >10 fold reduction in thin film thermal conductivity. Structural analysis of the films revealed a turbostratic structure with domain sizes on the order of 5–10 nm. Estimates of phonon scattering lengths at domain boundaries based on computationally derived group velocities were consistent with the observed film microstructure, and accounted for the reduction in thermal conductivity compared to values for bulk crystals.

Tannic Acid Coated Gold Nanorods Demonstrate A Distinctive Form Of Endosomal Uptake And Unique Distribution Within Cells, Emily A. Untener, Kristen K. Comfort, Elizabeth I. Maurer, Christin M. Grabinski, Donald A. Comfort, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

One of the primary challenges associated with nanoparticle-dependent biological applications is that endosomal entrapment in a physiological environment severely limits the desired targeting and functionality of the nanoconstructs. This study sought to overcome that challenge through a systematic approach of gold nanorod (GNR) functionalization: evaluating the influence of both aspect ratio and surface chemistry on targeted cellular internalization rates and preservation of particle integrity. Owing to their unique spectral properties and enhanced surface area, GNRs possess great potential for the advancement of nanobased delivery and imaging applications. However, their ability for efficient intracellular delivery while maintaining their specific physiochemical parameters …

Novel Platform Development Using An Assembly Of Carbon Nanotube, Nanogold And Immobilized Rna Capture Element Towards Rapid, Selective Sensing Of Bacteria, Elizabeth I. Maurer, Kristen K. Comfort, Saber M. Hussain, John J. Schlager, Sharmila M. Mukhopadhyay

Chemical and Materials Engineering Faculty Publications

This study examines the creation of a nano-featured biosensor platform designed for the rapid and selective detection of the bacterium Escherichia coli. The foundation of this sensor is carbon nanotubes decorated with gold nanoparticles that are modified with a specific, surface adherent ribonucleic acid (RNA) sequence element. The multi-step sensor assembly was accomplished by growing carbon nanotubes on a graphite substrate, the direct synthesis of gold nanoparticles on the nanotube surface, and the attachment of thiolated RNA to the bound nanoparticles.

The application of the compounded nanomaterials for sensor development has the distinct advantage of retaining the electrical behavior …

Biomedical Properties And Preparation Of Iron Oxide-Dextran Nanostructures By Maple Technique, Carmen Steluta Ciobanu, Simona Liliana Iconaru, Eniko Gyorgy, Mihaela Radu, Marieta Costache, Anca Dinischiotu, Philippe Le Coustumer, Khalid Lafdi, Daniela Predoi

Chemical and Materials Engineering Faculty Publications

Background: In this work the chemical structure of dextran-iron oxide thin films was reported. The films were obtained by MAPLE technique from composite targets containing 10 wt. % dextran with 1 and 5 wt.% iron oxide nanoparticles (IONPs). The IONPs were synthesized by co-precipitation method. A KrF* excimer laser source (λ = 248 nm, τFWHM≅25 ns, ν = 10 Hz) was used for the growth of the hybrid, iron oxide NPs-dextran thin films.

Results: Dextran coated iron oxide nanoparticles thin films were indexed into the spinel cubic lattice with a lattice parameter of 8.36 Å. The particle sized calculated was …

Carbon Nanotubes Grown On Glass Fiber As A Strain Sensor For Real Time Structural Health Monitoring, Matthew Boehle, Qiong Jiang, Lingchuan Li, Alexandre Lagounov, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

In order to more effectively monitor the health of composite structures, a fuzzy fiber sensor has been developed. The fuzzy fiber is a bundle of glass fibers with carbon nanotubes or nanofibers (CNTs or CNFs) grown on the surface. The nanotube coating makes the fiber bundle conductive while the small conductive path increases sensitivity. The fuzzy fiber sensor can replace conventional metal foil strain gauges in composite applications. The electrical response of the sensor is monitored in real time to measure strain, vibration, cracking and delamination. Continuous monitoring provides instant notification of any problems. Implementation of this sensor network in …

Limited Thermal Conductance Of Metal-Carbon Interfaces, Jaime J. Gengler, Sergei V. Shenogin, John E. Bultman, Ajit K. Roy, Andrey A. Voevodin, Christopher Muratore

Chemical and Materials Engineering Faculty Publications

The thermal conductance for a series of metal-graphite interfaces has been experimentally measured with time-domain thermoreflectance (TDTR). For metals with Debye temperatures up to ∼400 K, a linear relationship exists with the thermal conductance values. For metals with Debye temperatures in excess of ∼400 K, the measured metal-graphite thermal conductance values remain constant near 60 MW m−2 K−1. Titanium showed slightly higher conductance than aluminum, despite the closeness of atomic mass and Debye temperature for the two metals. Surface analysis was used to identify the presence of titaniumcarbide at the interface in contrast to the aluminum and gold-carbon interfaces (with …

Design Mixers To Minimize Effects Of Erosion And Corrosion Erosion, Julian B. Fasano, Eric E. Janz, Kevin J. Myers

Chemical and Materials Engineering Faculty Publications

A thorough review of the major parameters that affect solid-liquid slurry wear on impellers and techniques for minimizing wear is presented. These major parameters include (i) chemical environment, (ii) hardness of solids, (iii) density of solids, (iv) percent solids, (v) shape of solids, (vi) fluid regime (turbulent, transitional, or laminar), (vii) hardness of the mixer's wetted parts, (viii) hydraulic efficiency of the impeller (kinetic energy dissipation rates near the impeller blades), (ix) impact velocity, and (x) impact frequency. Techniques for minimizing the wear on impellers cover the choice of impeller, size and speed of the impeller, alloy selection, and surface …

Electrostatic Quadrupole Plasma Mass Spectrometer Measurements During Thin Film Depositions Using Simultaneous Matrix Assisted Pulsed Laser Evaporation And Magnetron Sputtering, Chad N. Hunter, Michael H. Check, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

A hybrid plasma deposition process, combining matrix assisted pulsed laser evaporation (MAPLE) of carbon nanopearls (CNPs) with magnetron sputtering of gold was investigated for growth of composite films, where 100 nm sized CNPs were encapsulated into a gold matrix. Composition and morphology of such composite films was characterized with x-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy (TEM) analysis. Carbondeposits on a gold magnetron sputter target and carbon impurities in the gold matrices of depositedfilms were observed while codepositing from gold and frozen toluene-CNP MAPLE targets in pure argon. Electrostatic quadrupole plasma analysis was used to determine that …

Preparation And Hydrogen Absorption/Desorption Of Nanoporous Palladium Thin Films, Wen-Chung Li, Thomas John Balk

Chemical and Materials Engineering Faculty Publications

Nanoporous Pd (np-Pd) was prepared by co-sputtering Pd-Ni alloy films onto Si substrates, followed by chemical dealloying with sulfuric acid. X-ray diffractometry and chemical analysis were used to track the extent of dealloying. The np-Pd structure was changed from particle-like to sponge-like by diluting the sulfuric acid etchant. Using suitable precursor alloy composition and dealloying conditions, np-Pd films were prepared with uniform and open sponge-like structures, with interconnected ligaments and no cracks, yielding a large amount of surface area for reactions with hydrogen. Np-Pd films exhibited shorter response time for hydrogen absorption/desorption than dense Pd films, showing promise for hydrogen …

Chameleon Coatings: Adaptive Surfaces To Reduce Friction And Wear In Extreme Environments, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

Adaptive nanocomposite coating materials that automatically and reversibly adjust their surface composition and morphology via multiple mechanisms are a promising development for the reduction of friction and wear over broad ranges of ambient conditions encountered in aerospace applications, such as cycling of temperature and atmospheric composition. Materials selection for these composites is based on extensive study of interactions occurring between solid lubricants and their surroundings, especially with novel in situ surface characterization techniques used to identify adaptive behavior on size scales ranging from 10−10 to 10−4 m. Recent insights on operative solid-lubricant mechanisms and their dependency upon the ambient environment …

Thermal Damage Approach Of Concrete: Application To Specimens Subjected To Combined Compressive And High Temperature Loads, Abdellah Menou, Ghassan Mounajed, Hocine Boussa, Christian La Borderie, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

Within the framework of study of concrete structures subjected to fire, .a theoretical and experimental work was conducted. The aim of this study was to investigate and to model the damage mechanisms of concrete after their exposure to high temperatures. The multiphase Digital Concrete Model as well as the damage model, MOD EV, which were both implemented on the finiteelem~ rit software package, SYMPHONIE, were used simμltaneously to assess the thermal damage of the concrete. In order to validate the thermal damage model, an experimental investigation was performed. The mechanical characteristics of 5 cementitious materials, which included cement paste, mortar, …

Effect Of Carbon Nanofiber-Matrix Adhesion On Polymeric Nanocomposite Properties—Part Ii, Khalid Lafdi, William Fox, Matthew Matzek, Emel Yildiz

Chemical and Materials Engineering Faculty Publications

A successful integration of two independent phases with good adhesion is imperative for effective translation of superior carbon nanofiber filler properties into a physically superior carbon nanocomposite. Carbon nanofibers were subjected to electrochemical oxidation in 0.1 M nitric acid for varying times.

The strength of adhesion between the nanofiber and an epoxy matrix was characterized by flexural strength and modulus. The surface functional groups formed and their concentration of nanofibers showed a dependence on the degree of oxidation. The addition of chemical functional groups on the nanofiber surface allows them to physically and chemically adhere to the continuous resin matrix. …

Carbon Nanoadditives To Enhance Latent Energy Storage Of Phase Change Materials, Shadab Shaikh, Khalid Lafdi, Kevin P. Hallinan

Chemical and Materials Engineering Faculty Publications

Latent energy storage capacity was analyzed for a system consisting of carbon nanoparticlesdopedphase changematerials (PCMs). Three types of samples were prepared by doping shell wax with single wall carbon nanotubes(SWCNTs), multiwall CNTs, and carbon nanofibers. Differential scanning calorimetry was used to measure the latent heat of fusion. The measured values of latent heat for all the samples showed a good enhancement over the latent heat of pure wax. A maximum enhancement of approximately 13% was observed for the wax/SWCNT composite corresponding to 1% loading of SWCNT. The change in latent heat was modeled by using an approximation for the intermolecular …

Nitrogen And Hydrogen Plasma Treatments Of Multiwalled Carbon Nanotubes, John G. Jones, A. R. Waite, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

This article investigates plasma treatment of vertically aligned multiwall carbon nanotube (CNT) films in different plasma environments for modification of surface chemistry and morphology. The surfaces of the CNTs were functionalized with a pulsed dc plasma treatment, where the power was directly applied to the nanotube film in low pressure argon/nitrogen and argon/hydrogen backgrounds. Optical emission spectroscopy was used to detect atomic and molecular excitations in the gas mixtures as well as in pure gases in the vicinity of the CNT films. In situx-ray photoelectron spectroscopy was performed on the treated samples to examine CNT surface chemistry after treatment. …

Signaling Pathways Activated By Interleukin-2 And Interluekin-4 Receptors Mediate T Lymphocyte Clonal Expansion, Kristen K. Comfort

Chemical and Materials Engineering Faculty Publications

Cells sense and respond to chemical and physical stimuli through signal transduction pathways, which mediate cell proliferation, differentiation, migration, and survival. The cytokines interleukin-2 (IL-2) and interleukin-4 (IL-4) are key regulators of the adaptive immune system, particularly influencing the clonal expansion and differentiation of T cells. At least in culture, both synergistic and antagonistic effects of IL-2 and IL-4 co-stimulation have been reported; the antagonism, when observed, is thought to arise from the utilization of a common subunit shared by IL-2 and IL-4 receptors. We have sought to characterize IL-2 and IL-4 signaling at the level of intracellular pathways activated …

Thermal Conductivity Improvement In Carbon Nanoparticle Doped Pao Oil: An Experimental Study, Shadab Shaikh, Khalid Lafdi, Rengasamy Ponnappan

Chemical and Materials Engineering Faculty Publications

The present work involves a study on the thermal conductivity of nanoparticle-oil suspensions for three types of nanoparticles, namely, carbon nanotubes(CNTs), exfoliated graphite (EXG), and heat treated nanofibers (HTT) with PAO oil as the base fluid. To accomplish the above task, an experimental analysis is performed using a modern light flash technique (LFA 447) for measuring the thermal conductivity of the three types of nanofluids, for different loading of nanoparticles.

The experimental results show a similar trend as observed in literature for nanofluids with a maximum enhancement of approximately 161% obtained for the CNT-PAO oil suspension. The overall percent enhancements …

Experimental Study On The Influence Of Foam Porosity And Pore Size On The Melting Of Phase Change Materials, Khalid Lafdi, Osama Mesalam Mesalhy, Shadab Shaikh

Chemical and Materials Engineering Faculty Publications

Experimental study was carried out to study the phase change heat transfer within a composite of phase change material (PCM) infiltrated high thermal conductivity foam. An experimental setup was built to measure the temperature profiles and capture the melting evolution of the PCM inside aluminum foams. Aluminum foams were used as the porous material, and low melting temperature paraffin wax was used as the PCM. It was observed from the results that the system parameters of the wax/foam composite had a significant influence on its heat transfer behavior.

By using higher porosity aluminum foam, the steady-state temperature was reached faster …

Effect Of Carbon Nanofiber Heat Treatment On Physical Properties Of Polymeric Nanocomposites—Part I, Khalid Lafdi, William Fox, Matthew Matzek, Emel Yildiz

Chemical and Materials Engineering Faculty Publications

The definition of a nanocomposite material has broadened significantly to encompass a large variety of systems made of dissimilar components and mixed at the nanometer scale. The properties of nanocomposite materials also depend on the morphology, crystallinity, and interfacial characteristics of the individual constituents. In the current work, vapor-grown carbon nanofibers were subjected to varying heat-treatment temperatures.

The strength of adhesion between the nanofiber and an epoxy (thermoset) matrix was characterized by the flexural strength and modulus. Heat treatment to 1800C∘ demonstrated maximum improvement in mechanical properties over that of the neat resin, while heat-treatment to higher temperatures demonstrated a …

Interfacial And Capillary Pressure Effects On The Thermal Performance Of Wax/Foam Composites, Mohammad Rajab Almajali, Khalid Lafdi, Shadab Shaikh

Chemical and Materials Engineering Faculty Publications

A numerical investigation study was performed to study the phase change behavior of wax/foam composite encapsulated in an aluminum casing. Two types of foam materials, namely, aluminum and carbon, were infiltrated with paraffin wax. The progress of melt interface and temperature distribution within the encapsulated composite was analyzed using computational fluid dynamics software (CFD). A two-energy equation model was implemented in the CFD software through the use of user-defined function (UDF). Interfacial effects influencing the heat transfer process at the casing-composite junction and between the wax-foam surfaces within the composite were addressed through the use of separate UDF. In addition, …

Oxygen Plasma Treatment And Deposition Of Cnx On A Fluorinated Polymer Matrix Composite For Improved Erosion Resistance, Christopher Muratore, Andras Korenyi-Both, John E. Bultman, A. R. Waite, John G. Jones, T. M. Storage, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

The use of polymer matrix composites in aerospace propulsion applications is currently limited by insufficient resistance to erosion by abrasive media. Erosion resistant coatings may provide necessary protection; however, adhesion to many high temperature polymer matrix composite (PMC) materials is poor. A low pressure oxygen plasma treatment process was developed to improve adhesion of CNx coatings to a carbon reinforced, fluorinated polymer matrix composite. Fullerene-like CNx was selected as an erosion resistant coating for its high hardness-to-elastic modulus ratio and elastic resilience which were expected to reduce erosion from media incident at different angles (normal or glancing) relative to the …