Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Missouri University of Science and Technology

Discipline
Keyword
Publication Year
Publication
Publication Type

Articles 361 - 390 of 2244

Full-Text Articles in Materials Science and Engineering

Boosting Snr Of Cascaded Fbgs In A Sapphire Fiber Through A Rapid Heat Treatment, Farhan Mumtaz, Hanok Tekle, Bohong Zhang, Jeffrey D. Smith, Ronald J. O'Malley, Rex Gerald, Jie Huang Jan 2023

Boosting Snr Of Cascaded Fbgs In A Sapphire Fiber Through A Rapid Heat Treatment, Farhan Mumtaz, Hanok Tekle, Bohong Zhang, Jeffrey D. Smith, Ronald J. O'Malley, Rex Gerald, Jie Huang

PSMRC Faculty Research

This Letter reports the performance of femtosecond (fs) laser-written distributed fiber Bragg gratings (FBGs) under high-temperature conditions up to 1600°C and explores the impact of rapid heat treatment on signal-to-noise ratio (SNR) enhancement. FBGs are essential for reliable optical sensing in extreme temperature environments. Comprehensive tests demonstrate the remarkable performance and resilience of FBGs at temperatures up to 1600°C, confirming their suitability for deployment in such conditions. The study also reveals significant fringe visibility improvements of up to ∼10 dB on a 1-m-long sapphire optical fiber through rapid heat treatment, representing a first-time achievement to the best of our knowledge. …

Go to article

Mechanical Properties Of Zrb2 Ceramics Determined By Two Laboratories, Jeffrey J. Swab, Jecee Jarman, William Fahrenholtz, Jeremy Lee Watts Jan 2023

Mechanical Properties Of Zrb2 Ceramics Determined By Two Laboratories, Jeffrey J. Swab, Jecee Jarman, William Fahrenholtz, Jeremy Lee Watts

Materials Science and Engineering Faculty Research & Creative Works

The mechanical properties for zirconium diboride (ZrB2) were measured at two laboratories and compared. Two billets of ZrB2 were prepared by hot-pressing commercial powder. The relative densities of the billets were >99% and with an average grain size of 5.9 ± 4.5 µm. Both laboratories prepared American Society for Testing and Materials (ASTM) C1161 B-bars for strength and ASTM C1421 bars with notch configuration A for fracture toughness. Specimens were machined by diamond grinding at the Army Research Laboratory (ARL) and electrical discharge machining (EDM) at Missouri S&T. Strength bars tested at Missouri S&T were polished to a.25 μm finish …

Go to article

Coating Compositions And Methods For Using The Same, Fateme Rezaei, Thomas P. Schuman, Glenn C. Morrison Jan 2023

Coating Compositions And Methods For Using The Same, Fateme Rezaei, Thomas P. Schuman, Glenn C. Morrison

Patents

Coating compositions and methods for using the same are disclosed. The coating compositions can include an aminosilica adsorbent. The coating compositions can adsorb CO2.

Go to article

Impact Of Alumina-Based Binder On Formation Of Dense Strontium Zirconate Ceramics, Janos E. Kanyo, R. Sharon Uwanyuze, Jiyao Zhang, Rainer Hebert, Stefan Schafföner, Lesley Frame Jan 2023

Impact Of Alumina-Based Binder On Formation Of Dense Strontium Zirconate Ceramics, Janos E. Kanyo, R. Sharon Uwanyuze, Jiyao Zhang, Rainer Hebert, Stefan Schafföner, Lesley Frame

Materials Science and Engineering Faculty Research & Creative Works

Strontium zirconate (SrZrO3) is a technical ceramic with potential for refractory applications due to its chemical stability at high temperatures, high melting temperature, and favorable thermal expansion coefficient. Practical use of SrZrO3 is limited by poor mechanical strength relative to ceramics such as alumina (Al2O3). Sintering of SrZrO3 with a hydratable Al2O3 binder is investigated as a method for improving mechanical performance. Density, phase composition, thermomechanical properties, and chemical stability in contact with alloys up to 1350 °C are considered. Results are compared with SrZrO3 samples formed using a traditional polyvinyl alcohol (PVA) binder. SrZrO3 reacts with alumina during sintering …

Go to article

In Situ And Real-Time Mold Flux Analysis Using A High-Temperature Fiber-Optic Raman Sensor For Steel Manufacturing Applications, Bohong Zhang, Hanok Tekle, Ronald J. O'Malley, Todd Sander, Jeffrey D. Smith, Rex E. Gerald, Jie Huang Jan 2023

In Situ And Real-Time Mold Flux Analysis Using A High-Temperature Fiber-Optic Raman Sensor For Steel Manufacturing Applications, Bohong Zhang, Hanok Tekle, Ronald J. O'Malley, Todd Sander, Jeffrey D. Smith, Rex E. Gerald, Jie Huang

Materials Science and Engineering Faculty Research & Creative Works

Continuous Casting in Steel Production Uses Specially Developed Oxyfluoride Glasses (Mold Fluxes) to Lubricate a Mold and Control the Solidification of the Steel in the Mold. the Composition of the Flux Impacts Properties, Including Basicity, Viscosity, and Crystallization Rate, All of Which Affect the Stability of the Casting Process and the Quality of the Solidified Steel. However, Mold Fluxes Interact with Steel during the Casting Process, Resulting in Flux Chemistry Changes that Must Be Considered in the Flux Design. Currently, the Chemical Composition of Mold Flux Must Be Determined by Extracting Flux Samples from the Mold during Casting and Then …

Go to article

A Study On The Impact Of Silicon And Manganese On Peritectic Behavior In Low Alloy Steels Assisted By Mold Thermal Mapping Technology And Shell Growth Measurements, Damilola Balogun, Muhammad Roman, Rex E. Gerald, Laura Bartlett, Jie Huang, Ronald J. O'Malley Jan 2023

A Study On The Impact Of Silicon And Manganese On Peritectic Behavior In Low Alloy Steels Assisted By Mold Thermal Mapping Technology And Shell Growth Measurements, Damilola Balogun, Muhammad Roman, Rex E. Gerald, Laura Bartlett, Jie Huang, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Non-Uniform Shell Growth Commonly Caused by the Peritectic Transformation in Low Carbon and Low Alloy Steels Has Been Directly Correlated with Mold Thermal Maps using a Mold Immersion Test into a Molten Steel Alloy. Mold Thermal Maps Were Obtained by Performing Real-Time Temperature Measurements with Optical Fibers Embedded 1 Mm from the Mold Working Surface. Shell Growth Measurements Were Obtained by 3D Optical Scanning of the Recovered Steel Shell Following Immersion Testing. the Effects of Silicon and Manganese on the Shell Growth and Mold Temperature Maps Have Been Examined in Relation to the Peritectic Transformation for Varying Carbon Contents. Results …

Go to article

Oxidation Behavior Of Nb-Coated Zirconium Diboride, Jan E. Förster, William Fahrenholtz, Gregory E. Hilmas, Ravisankar Naraparaju Jan 2023

Oxidation Behavior Of Nb-Coated Zirconium Diboride, Jan E. Förster, William Fahrenholtz, Gregory E. Hilmas, Ravisankar Naraparaju

Materials Science and Engineering Faculty Research & Creative Works

Metallic Nb-Coatings Were Deposited on Top of ZrB2 by Means of Magnetron Sputtering to Improve its Oxidation Resistance. High Temperature Oxidation Tests Have Revealed that the Metallic Nb-Coatings Lead to the Formation of a Dense Solid and Protective Reaction Zone in Addition to a More Stable B2O3 Liquid Solution at the Surface. Compared to Baseline ZrB2, a Reduction in the Oxidation Kinetics, as Well as the Thickness of the Porous Zirconia Layer by 71%, Has Been Achieved with the Help of Nb-Coatings. a Liquid Phase Sintering by Molten Nb2O5 Mechanism Was …

Go to article

The Angiogenic Potential Of Ph-Neutral Borophosphate Bioactive Glasses, Bradley A. Bromet, Nathaniel P. Blackwell, Nada Abokefa, Parker Freudenberger, Rebekah L. Blatt, Richard K. Brow, Julie A. Semon Jan 2023

The Angiogenic Potential Of Ph-Neutral Borophosphate Bioactive Glasses, Bradley A. Bromet, Nathaniel P. Blackwell, Nada Abokefa, Parker Freudenberger, Rebekah L. Blatt, Richard K. Brow, Julie A. Semon

Materials Science and Engineering Faculty Research & Creative Works

Borate bioactive glasses have gained attention in recent years due to their therapeutic and regenerative effects in vivo. However, borate bioactive glasses release alkaline ions, increasing the local pH and creating a toxic environment for cell culture studies. A partial compositional substitution of phosphate for borate can create a pH-neutral glass that does not significantly affect the local pH while still releasing therapeutic ions. In the present study, a series of Na-Ca-borophosphate bioactive glasses with different borate-to-phosphate ratios was evaluated in vitro and in vivo for cytotoxicity and angiogenic effects. Compared to more basic borate glasses, the pH-neutral glasses supported …

Go to article

High Temperature Dielectric Properties Of Calcium Zirconate, Alan Devoe, Hung Trinh, Fatih Dogan Jan 2023

High Temperature Dielectric Properties Of Calcium Zirconate, Alan Devoe, Hung Trinh, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

The electrical properties of dense, high purity CaZrO3 discs, sintered at 1380°C with and without added ZrO2, were investigated up to 950°C. Dielectric constant, loss tangent, and electrical conductivity were measured from 25 to 725°C, and the real and imaginary impedances were measured between 800 and 950°C by impedance spectroscopy techniques. Dielectric constant increased by 8% above 300°C and loss tangent increased from.1% at 25°C to ∼2% above 300°C. Activation energy of electrical conductivity determined between 300°C and 950°C by alternative current (AC) and direct current (DC) measurements. These results indicate that CaZrO3 could be a useful dielectric material for …

Go to article

Intragranular Nanocomposite Powders As Building Blocks For Ceramic Nanocomposites, Ryan D. Dempsey, Xiaoqing He, Jonathan A. Scott, David W. Lipke Jan 2023

Intragranular Nanocomposite Powders As Building Blocks For Ceramic Nanocomposites, Ryan D. Dempsey, Xiaoqing He, Jonathan A. Scott, David W. Lipke

Materials Science and Engineering Faculty Research & Creative Works

A powder-based bottom-up processing scheme is introduced for the production of ceramic nanocomposites. Internal displacement reactions between solid solution powders and metallic reactants proceeding via gaseous intermediates are utilized to generate nanostructured building blocks for the synthesis of ceramic nanocomposites. Subsequent rapid sintering results in ceramic nanocomposites, whose microstructures are inherited from the building blocks. This processing scheme is demonstrated for the production of titanium carbide nanocomposites featuring up to 28 wt.% intragranular tungsten inclusions derived from titanium-tungsten mixed carbide powders. Heat treatment of mixed carbide powders in evacuated ampoules containing titanium sponge and iodine at 1000°C for 24 h …

Go to article

Synthesis, Densification, And Cation Inversion In High Entropy (Co,Cu,Mg,Ni,Zn)Al2o4 Spinel, Cole A. Corlett, Nina Obradovic, Jeremy Lee Watts, Eric W. Bohannan, William Fahrenholtz Jan 2023

Synthesis, Densification, And Cation Inversion In High Entropy (Co,Cu,Mg,Ni,Zn)Al2o4 Spinel, Cole A. Corlett, Nina Obradovic, Jeremy Lee Watts, Eric W. Bohannan, William Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

The synthesis, densification behavior, and crystallographic site occupancy were investigated for four different spinel-based ceramics, including a high-entropy spinel (Co0.2Cu0.2Mg0.2Ni0.2 Zn0.2)Al2O4. Each composition was reacted to form a single phase, but analysis of X-ray diffraction patterns revealed differences in cation site occupancy with the high-entropy spinel being nearly fully normal. Densification behavior was investigated and showed that fully dense ceramics could be produced by hot pressing at temperatures as low as 1375°C for all compositions. Vickers' hardness values were at least 10 GPa for all compositions. The …

Go to article

Performance Evaluation Of Composite Sandwich Structures With Additively Manufactured Aluminum Honeycomb Cores With Increased Bonding Surface Area, M. Rangapuram, S. K. Dasari, Joseph William Newkirk, K. Chandrashekhara, H. Misak, P. R. Toivonen, D. Klenosky, T. Unruh, J. Sam Jan 2023

Performance Evaluation Of Composite Sandwich Structures With Additively Manufactured Aluminum Honeycomb Cores With Increased Bonding Surface Area, M. Rangapuram, S. K. Dasari, Joseph William Newkirk, K. Chandrashekhara, H. Misak, P. R. Toivonen, D. Klenosky, T. Unruh, J. Sam

Materials Science and Engineering Faculty Research & Creative Works

Modern aerostructures, including wings and fuselages, increasingly feature sandwich structures due to their high-energy absorption, low weight, and high flexural stiffness. The face sheet of these sandwich structures are typically thin composite laminates with interior honeycombs made of Nomex or aluminum. Standard cores are structurally efficient, but their design cannot be varied throughout the structure. With additive manufacturing (AM) technology, these core geometries can be altered to meet the design requirements that are not met in standard honeycomb cores. This study used a modified aluminum honeycomb core, with increased surface area on the top and bottom, as the core material …

Go to article

Final-Stage Densification Kinetics Of Direct Current–Sintered Zrb2, Austin D. Stanfield, Steven M. Smith, Suzana Filipović, Nina Obradović, Vladimir Buljak, Gregory E. Hilmas, William Fahrenholtz Jan 2023

Final-Stage Densification Kinetics Of Direct Current–Sintered Zrb2, Austin D. Stanfield, Steven M. Smith, Suzana Filipović, Nina Obradović, Vladimir Buljak, Gregory E. Hilmas, William Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

Final-stage sintering was analyzed for nominally phase pure zirconium diboride synthesized by borothermal reduction of high-purity ZrO2. Analysis was conducted on ZrB2 ceramics with relative densities greater than 90% using the Nabarro–Herring stress–directed vacancy diffusion model. Temperatures of 1900°C or above and an applied uniaxial pressure of 50 MPa were required to fully densify ZrB2 ceramics by direct current sintering. Ram travel data were collected and used to determine the relative density of the specimens during sintering. Specimens sintered between 1900 and 2100°C achieved relative densities greater than 97%, whereas specimens sintered below 1900°C failed to …

Go to article

Morphological And Structural Characterization Of Mgal2o4 Spinel, Nina Obradović, Suzana Filipović, William Fahrenholtz, Bojan A. Marinkovic, Jelena Rogan, Steva Lević, Antonije Đorđević, Vladimir B. Pavlović Jan 2023

Morphological And Structural Characterization Of Mgal2o4 Spinel, Nina Obradović, Suzana Filipović, William Fahrenholtz, Bojan A. Marinkovic, Jelena Rogan, Steva Lević, Antonije Đorđević, Vladimir B. Pavlović

Materials Science and Engineering Faculty Research & Creative Works

Magnesium aluminate has the spinel structure along with good mechanical, chemical, and thermal properties. Magnesium aluminate has a wide range of applications including refractory ceramics, optically transparent ceramic windows, and armors. Its low dielectric permeability and low loss tangent enable its applications for integrated electronic devices, as well. In this paper, MgO and Al2O3 powders were mixed in a one-to-one molar ratio and calcined at temperatures ranging from 1500 to 1800o C to produce phase pure spinel. Thereafter, pellets were crushed and treated in a planetary ball mill for 60 min to obtain a fine powder. All …

Go to article

Antioxidant Theranostic Copolymer-Mediated Reduction In Oxidative Stress Following Traumatic Brain Injury Improves Outcome In A Mouse Model, Aria W. Tarudji, Connor C. Gee, Hunter A. Miller, Rylie Steffen, Evan T. Curtis, Aaron M. Priester, Anthony J. Convertine, Forrest M. Kievit Jan 2023

Antioxidant Theranostic Copolymer-Mediated Reduction In Oxidative Stress Following Traumatic Brain Injury Improves Outcome In A Mouse Model, Aria W. Tarudji, Connor C. Gee, Hunter A. Miller, Rylie Steffen, Evan T. Curtis, Aaron M. Priester, Anthony J. Convertine, Forrest M. Kievit

Materials Science and Engineering Faculty Research & Creative Works

Following a traumatic brain injury (TBI), excess reactive oxygen species (ROS) and lipid peroxidation products (LPOx) are generated and lead to secondary injury beyond the primary insult. A major limitation of current treatments is poor target engagement, which has prevented success in clinical trials. Thus, nanoparticle-based treatments have received recent attention because of their ability to increase accumulation and retention in damaged brain. Theranostic neuroprotective copolymers (NPC3) containing thiol functional groups can neutralize ROS and LPOx. Immediate administration of NPC3 following injury in a controlled cortical impact (CCI) mouse model provides a therapeutic window in reducing ROS levels at 2.08–20.83 …

Go to article

The Effect Of Crystal Anisotropy On Fracture Toughness And Strength Of Zrb2 Microcantilevers, Tamás Csanádi, Ahmad Azizpour, Marek Vojtko, William Fahrenholtz Jan 2023

The Effect Of Crystal Anisotropy On Fracture Toughness And Strength Of Zrb2 Microcantilevers, Tamás Csanádi, Ahmad Azizpour, Marek Vojtko, William Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

The influence of crystal anisotropy on the micromechanical properties of ceramic grains plays an important role in the design of the macromechanical performance of bulk polycrystalline samples. To this end, the effect of crystal orientation on fracture toughness and strength was investigated by microcantilever bending experiments combined with finite element method (FEM) simulations in grains of a polycrystalline ZrB2 sample. The sample was prepared by hot pressing and the crystal orientations were determined by electron backscatter diffraction after careful surface preparation. The bending tests were carried out on notched and unnotched microcantilevers cut from specific grains along the prismatic (⊥ …

Go to article

Additive Manufacturing Of (Mgconicuzn)O High-Entropy Oxide Using A 3d Extrusion Technique And Oxide Precursors, Ruoyu Chen, Saisai Li, Qingfeng Yan, Haiming Wen Jan 2023

Additive Manufacturing Of (Mgconicuzn)O High-Entropy Oxide Using A 3d Extrusion Technique And Oxide Precursors, Ruoyu Chen, Saisai Li, Qingfeng Yan, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

This report presents an additive manufacturing approach, for the first time, to producing high-entropy oxides (HEOs) using a 3D extrusion-based technique with oxide precursors. The precursors were prepared by a wet chemical method from sulfates. Additives were utilized to optimize the rheological properties of the printing inks with these precursors, and the properties of the printed HEOs were improved by increasing the solid content of the inks. When ink with a solid content of 78 wt% was used for printing, the resulting HEO exhibited a relative density of 92% and a high dielectric constant after undergoing pressure less sintering at …

Go to article

High-Temperature Interactions Between Titanium Alloys And Strontium Zirconate Refractories, R. Sharon Uwanyuze, Baris Yavas, Jiyao Zhang, Janos E. Kanyo, Lesley D. Frame, Rainer J. Hebert, Stefan Schafföner, S. Pamir Alpay Jan 2023

High-Temperature Interactions Between Titanium Alloys And Strontium Zirconate Refractories, R. Sharon Uwanyuze, Baris Yavas, Jiyao Zhang, Janos E. Kanyo, Lesley D. Frame, Rainer J. Hebert, Stefan Schafföner, S. Pamir Alpay

Materials Science and Engineering Faculty Research & Creative Works

We investigated interactions between Ti6Al4V alloys and strontium zirconate (SrZrO3) ceramic to assess its potential as a refractory mold material in investment casting. We developed a robust yet simple procedure to examine both the liquid–solid and solid–solid interactions using pellets in drop casting and diffusion couple methods. Reaction layers were characterized using optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and x-ray diffraction (XRD). The results were compared to alumina (Al2O3) which is still a common refractory ceramic for molds in investment casting. Our findings indicate that Ti6Al4V surfaces in contact with …

Go to article

Strength Retention Of Single-Phase High-Entropy Diboride Ceramics Up To 2000°C, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Yue Zhou, Jincheng Bai Jan 2023

Strength Retention Of Single-Phase High-Entropy Diboride Ceramics Up To 2000°C, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Yue Zhou, Jincheng Bai

Materials Science and Engineering Faculty Research & Creative Works

The mechanical properties of single-phase (Hf0.2,Nb0.2,Ta0.2,Ti0.2,Zr0.2)B2 ceramics with high purity were investigated. The resulting ceramics had relative density greater than 99%, and an average grain size of 4.3 ± 1.6 μm. At room temperature (RT), the Vickers hardness was 25.2 ± 0.6 GPa at a load of 0.49 N, Young's modulus was 551 ± 7 GPa, fracture toughness was 4.5 ± 0.4 MPa m1/2, and flexural strength was 507 ± 10 MPa. Flexural strength increased by more than 50% from 507 ± 10 MPa at RT to 776 ± …

Go to article

Improving Strength And Microstructure Of Sic Reticulated Porous Ceramic Through In-Situ Generation Of Sic Whiskers Within Hollow Voids, Ruoyu Chen, Kunshi Xie, Haipeng Zhu, Qun He, Saisai Li, Haiming Wen Jan 2023

Improving Strength And Microstructure Of Sic Reticulated Porous Ceramic Through In-Situ Generation Of Sic Whiskers Within Hollow Voids, Ruoyu Chen, Kunshi Xie, Haipeng Zhu, Qun He, Saisai Li, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

SiC Reticulated Porous Ceramic with Excellent Strength and High-Density Ceramic Struts Was Successfully Prepared using the Polymer Replica Method, Followed by Pressureless Sintering under a Buried Charcoal Atmosphere. First, a Polyurethane (PU) Template Was Coated with a Si Slurry and Then a SiC-Containing Slurry, and Subsequently Heated under the Buried Charcoal Atmosphere. to Ensure Excellent Coating Ability of the Slurries, the Viscosity, Thixotropy, and Yield Stresses of the Si Slurry Were Optimized by Adjusting the Content of the Thickening Agent. during Heating, Si in the Coating Layer Reacted with the Residual C and CO Gas from the PU Template and …

Go to article

Phenomenological Analysis Of Surface Degradation Of Metallic Materials In Extreme Environment, Simon N. Lekakh, Oleg Neroslavsky Jan 2023

Phenomenological Analysis Of Surface Degradation Of Metallic Materials In Extreme Environment, Simon N. Lekakh, Oleg Neroslavsky

Materials Science and Engineering Faculty Research & Creative Works

The resistance to surface degradation in metallic alloys plays an important role for the lifetime of the components working in harsh environments. The mechanisms involved in degradation of metallic surface in a high-temperature aggressive gaseous atmosphere include the following: forming adherent to the surface multiphase oxide layer, partial spallation, and possible vaporization of formed compounds. The governing equation, which describes a parabolic growth of adherent layer, time-dependent vaporization, and cross-linked to instantaneous thickness of adherent layer spallation rate, was suggested and analyzed. The several relationships between the kinetic constants were defined from analysis of the governing equation. Design of routes …

Go to article

Real-Time Air Gap And Thickness Measurement Of Continuous Caster Mold Flux By Extrinsic Fabry-Perot Interferometer, Abhishek Prakash Hungund, Hanok Tekle, Bohong Zhang, Ronald J. O'Malley, Jeffrey D. Smith, Rex E. Gerald, Jie Huang Jan 2023

Real-Time Air Gap And Thickness Measurement Of Continuous Caster Mold Flux By Extrinsic Fabry-Perot Interferometer, Abhishek Prakash Hungund, Hanok Tekle, Bohong Zhang, Ronald J. O'Malley, Jeffrey D. Smith, Rex E. Gerald, Jie Huang

Materials Science and Engineering Faculty Research & Creative Works

Mold Flux plays a critical role in continuous casting of steel. Along with many other functions, the mold flux in the gap between the solidifying steel shell and the mold serves as a medium for controlling heat transfer and as a barrier to prevent shell sticking to the mold. This manuscript introduces a novel method of monitoring the structural features of a mold flux film in real-time in a simulated mold gap. A 3-part stainless-steel mold was designed with a 2 mm, 4 mm and, 6 mm step profile to contain mold flux films of varying thickness. An Extrinsic Fabry-Perot …

Go to article

Modeling Phase Selection And Extended Solubility In Rapid Solidified Alloys, Azeez Akinbo, Yijia Gu Jan 2023

Modeling Phase Selection And Extended Solubility In Rapid Solidified Alloys, Azeez Akinbo, Yijia Gu

Materials Science and Engineering Faculty Research & Creative Works

A new phase selection model based on the time-dependent nucleation theory was developed to investigate the effect of rapid solidification on extended solubility. The model was applied to predict the solubility as a function of undercooling for several binary Al alloys. The predictions of both eutectic and peritectic systems show good agreement with experimental data. It was demonstrated that the developed model is better than the T 0-line method, which neglected the kinetic process of nucleation. Furthermore, the model can also be applied to ternary and multicomponent phases assuming the nucleation is limited by the scarcest species or the slowest …

Go to article

Characterization Of Virgin, Re-Used, And Oxygen-Reduced Copper Powders Processed By The Plasma Spheroidization Process, M. Hossein Sehhat, David Perez-Palomino, Connor Wiedemeier, Tristan Cullom, Joseph William Newkirk Jan 2023

Characterization Of Virgin, Re-Used, And Oxygen-Reduced Copper Powders Processed By The Plasma Spheroidization Process, M. Hossein Sehhat, David Perez-Palomino, Connor Wiedemeier, Tristan Cullom, Joseph William Newkirk

Materials Science and Engineering Faculty Research & Creative Works

Fabrication of parts with high mechanical properties heavily depend on the quality of powder deployed in the fabrication process. Copper powder in three different powder types were spheroidized using radio-frequency inductively coupled plasma (ICP) spheroidization process (TekSphero-15 system). The characterized powders include virgin powder as purchased from the powder manufacturer, powder used in electron beam powder bed fusion (EB-PBF) process, and reconditioned powder, which was used powder that underwent an oxygen-reduction treatment. The goal of spheroidizing these powder types was to evaluate the change in powder morphology, the possibility of enhancing the powder properties back to their as-received conditions, and …

Go to article

Thermal And Electrical Properties Of Spark Plasma Sintered (Ti,Cr)B2 Ceramics, Steven M. Smith, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Laura Silvestroni Jan 2023

Thermal And Electrical Properties Of Spark Plasma Sintered (Ti,Cr)B2 Ceramics, Steven M. Smith, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Laura Silvestroni

Materials Science and Engineering Faculty Research & Creative Works

Thermal and electrical properties were measured for TiB2 ceramics containing varying CrB2 contents up to 33 mol%. The room-temperature thermal diffusivity decreased with increasing Cr content from 0.330 ± 0.003 cm2/s for pure TiB2 to 0.060 ± 0.003 cm2/s for (Ti0.66Cr0.33)B2. The amount of anisotropy in the coefficients of thermal expansion increased with increasing Cr content and the c-axis had the greatest dependence on Cr addition, with an increase of more than 25% in the thermal expansion for 33 mol% CrB2 compared to TiB2, whereas the a-axis only increased by about 8%. The electrical conductivity was the lowest for (Ti0.66Cr0.33)B2 …

Go to article

Characterization Of Virgin, Re-Used, And Oxygen-Reduced Copper Powders Processed By The Plasma Spheroidization Process, M. Hossein Sehhat, David Perez-Palomino, Connor Wiedemeier, Tristan Cullom, Joseph William Newkirk Jan 2023

Characterization Of Virgin, Re-Used, And Oxygen-Reduced Copper Powders Processed By The Plasma Spheroidization Process, M. Hossein Sehhat, David Perez-Palomino, Connor Wiedemeier, Tristan Cullom, Joseph William Newkirk

Materials Science and Engineering Faculty Research & Creative Works

Fabrication of parts with high mechanical properties heavily depend on the quality of powder deployed in the fabrication process. Copper powder in three different powder types were spheroidized using radio-frequency inductively coupled plasma (ICP) spheroidization process (TekSphero-15 system). The characterized powders include virgin powder as purchased from the powder manufacturer, powder used in electron beam powder bed fusion (EB-PBF) process, and reconditioned powder, which was used powder that underwent an oxygen-reduction treatment. The goal of spheroidizing these powder types was to evaluate the change in powder morphology, the possibility of enhancing the powder properties back to their as-received conditions, and …

Go to article

Boro/Carbothermal Reduction Co-Synthesis Of Dual-Phase High-Entropy Boride-Carbide Ceramics, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Stefano Curtarolo Jan 2023

Boro/Carbothermal Reduction Co-Synthesis Of Dual-Phase High-Entropy Boride-Carbide Ceramics, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Stefano Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

Dense, dual-phase (Cr,Hf,Nb,Ta,Ti,Zr)B2-(Cr,Hf,Nb,Ta,Ti,Zr)C ceramics were synthesized by boro/carbothermal reduction of oxides and densified by spark plasma sintering. The high-entropy carbide content was about 14.5 wt%. Grain growth was suppressed by the pinning effect of the two-phase ceramic, which resulted in average grain sizes of 2.7 ± 1.3 µm for the high-entropy boride phase and 1.6 ± 0.7 µm for the high-entropy carbide phase. Vickers hardness values increased from 25.2 ± 1.1 GPa for an indentation load of 9.81 N to 38.9 ± 2.5 GPa for an indentation load of 0.49 N due to the indentation size effect. Boro/carbothermal …

Go to article

Re-Assembling Polymer Particle Package For Conformance Control And Fluid Loss Control, Jingyang Pu, Baojun Bai, Thomas P. Schuman Jan 2023

Re-Assembling Polymer Particle Package For Conformance Control And Fluid Loss Control, Jingyang Pu, Baojun Bai, Thomas P. Schuman

Patents

This invention is broadly concerned with compositions and processes for oilfield applications. More specifically, this invention relates to novel polymer constructed packages that, when pumped into a petroleum well, provide tunable characteristics of transformation and delayed self-assembly with each other under reservoir conditions to yield strong, elastic, bulk gel materials. The compositions comprise a polymer, assembling agents, and optional additives used for the re-assembly stage are uniformly-distributed within the initial gel particles. The polymer particle packages absorb water and swell upon exposure to water, thus exposing the "assembling agents" that enable re-assembly. Both swelling and re-assembly are proportionally controlled via …

Go to article

Cast Iron Alloy For Automotive Engine Applications With Superior High Temperature Oxidation Properties, Larry Alan Godlewski, Mei Li, Carlos Engler-Pinto, Simon Naumovich Lekakh Jan 2023

Cast Iron Alloy For Automotive Engine Applications With Superior High Temperature Oxidation Properties, Larry Alan Godlewski, Mei Li, Carlos Engler-Pinto, Simon Naumovich Lekakh

Patents

A cast iron alloy is provided with a composition in weight percent (wt.%) of carbon between 2.6 to 3.4 wt.%, silicon between 2.4 to 3.2 wt. %, manganese between 0.3 to 0.6 wt. %, molybdenum between 0.4 to 1.2 wt. %, nickel between 0.6 to 1.75 wt.%, magnesium between 0.01 to 0.075 wt.%, aluminum between 1.8 to 3.5 wt.%, sulfur between 0.003 to 0.025 wt.%, zirconium between 0.001 to 0.02 wt. %, cerium between 0.001 to 0.03 wt. %, lanthanum between 0.0005 to 0.02 wt. %, and a balance of iron and unavoidable trace elements. A part formed from the …

Go to article

Characterization Of Virgin, Re-Used, And Oxygen-Reduced Copper Powders Processed By The Plasma Spheroidization Process, M. Hossein Sehhat, David Perez-Palomino, Connor Wiedemeier, Tristan Cullom, Joseph William Newkirk Jan 2023

Characterization Of Virgin, Re-Used, And Oxygen-Reduced Copper Powders Processed By The Plasma Spheroidization Process, M. Hossein Sehhat, David Perez-Palomino, Connor Wiedemeier, Tristan Cullom, Joseph William Newkirk

Mathematics and Statistics Faculty Research & Creative Works

Fabrication of parts with high mechanical properties heavily depend on the quality of powder deployed in the fabrication process. Copper powder in three different powder types were spheroidized using radio-frequency inductively coupled plasma (ICP) spheroidization process (TekSphero-15 system). The characterized powders include virgin powder as purchased from the powder manufacturer, powder used in electron beam powder bed fusion (EB-PBF) process, and reconditioned powder, which was used powder that underwent an oxygen-reduction treatment. The goal of spheroidizing these powder types was to evaluate the change in powder morphology, the possibility of enhancing the powder properties back to their as-received conditions, and …

Go to article

First Prev Next Last