Materials Science and Engineering Commons^™

Knudsen Effusion Study Of The Vaporization Of Cdo(S), R. Tom Coyle, Gordon Lewis

Materials Science and Engineering Faculty Research & Creative Works

Knudsen effusion studies were conducted on CdO(s) in fused‐SiO2 Knudsen cells from 889 to 1110 K. The orifice size was varied; the largest cell orifice yielded a calculated pressure significantly lower than could be accounted for by experimental error. Average‐slope‐ and average‐free‐energy‐function‐based values of ΔHc298 were 86.9 ± 1.1 and 88.8 ± 0.5 kcal/mol, respectively. The data from the present work were combined with those of previous investigators using a method discussed by McCreary and Thorn; a ΔHc298 of 88.2 ± 0.2 kcal/mol was obtained. Using this combined value for ΔHc298 and ΔSc298= 51.40 ± 0.1 eu (obtained from the …

Magnetostrictive Aftereffect In A Dilute 50fe-50ni-C Alloy, Raj Master, Manfred Wuttig

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

X-Ray Powder Data And Unit Cell Parameters Of Mgcl2.6h2o, Charles A. Sorrell, Roy R. Ramey

Materials Science and Engineering Faculty Research & Creative Works

Detailed X-ray powder data for MgCl2·6H2O were obtained by diffractometry by use of CuKα radiation at 22°C. The data were indexed on a bimolecular monoclinic unit cell, space group C2/m, with a = 9.858 ± 0.001 Å; b = 7.107 ± 0.001 Å; c = 6.069 ± 0.001 Å; ß = 93° 47′ ± 10′. Calculated density was 1.591 g/cm3, compared with a measured density of 1.593 ± 0.003 g/cm3. © 1974, American Chemical Society. All rights reserved.

Influence Of Oxygen Activity On The Sintering Of Mgcr2o4, Harlan U. Anderson

Materials Science and Engineering Faculty Research & Creative Works

The sintering behavior of MgCr2O4 powder compacts was investigated as a function of temperature, time, and oxygen activity. The results show that MgCr2O4 cannot be densified to >70% of theoretical density at temperatures up to 1700°C if the oxygen activity exceeds 10−6 atm. The oxygen activity must be decreased to <10−10 atm before densities exceeding 90% of theoretical can be achieved. Weight loss and X‐ray data indicated that maximum density occurred at an oxygen activity just above that where MgCr2O4 becomes unstable. Copyright © 1974, Wiley Blackwell. All rights reserved

Detection Of Impurities In Zinc Sulfate Electrolytes By Cyclic Voltammetry Techniques., Bruce Alan Lamping

Masters Theses

"A cyclic voltammetric technique has been developed for quantitatively detecting the presence of active chemical species present in zinc sulfate electrolytes. The experimental apparatus consisted of a pyrex "H" cell, an Al cathode encased in a Teflon holder, a carbon anode and a mercurous sulfate reference electrode. Voltammograms were obtained from industrial, purified neutral leach solution (Cominco Ltd., Trail, B.C.) acidified to give a final concentration of 0.77 M Zn⁺⁺, 1 M H₂SO₄. The polarization curves were then evaluated and used as a reference standard to compare with results obtained when various organic and …

Phase Equilibria And Transformations In Potassium Sulfate, Chromate, Molybdate, And Tungstate, Roy Richard Ramey

Doctoral Dissertations

"Thermal expansion and transformations of K₂SO₄, K₂CrO₄, K₂MoO₄, and K₂WO₄ were studied by high temperature diffractometry, differential thermal analysis, and dilatometry. K₂SO₄ and K₂CrO₄ transform from an orthorhombic to a hexagonal structure at 580°C and 670°C respectively, with initiation of the transformation probably related to increased amplitude of S-O tetrahedral vibrations. K₂MoO₄ and K₂WO₄ transform from a monoclinic to an orthorhombic structure at 300° and 370°C respectively. A minor K₂MoO_{4 …}

Effect Of Dissolved Water On Physical Properties Of Silver Borate Glasses, E Richard Reynolds

Masters Theses

"The effect of dissolved water on borate glasses containing 4-20 mol % Ag₂O was investigated. Water was dissolved in the glasses by bubbling with a carrier gas (oxygen) containing different partial pressures of water vapor. A minimum in water solubility was found at 11 mol % Ag₂O. Water contents in excess of 0.5 mol % H₂O did not have a great effect on the transition temperature or the dilatometric softening point. Below 15 mol % Ag₂O, the water content had no effect on the thermal expansion coefficients. Beyond 15 mol % Ag …

Magnetostrictive Aftereffects In A Dilute 50fe-50ni-C Alloy, Raj N. Master

Masters Theses

"Crystallographically equivalent interstitial sites are energetically equivalent when the host crystal is free of any fields. This situation is shown in Fig. Pl from which it may be appreciated that the difference of the free energy of the "crystal" with an interstitial "I" located in "x" and "y" sites, respectively, is equal to zero. This energy equivalence of the various interstitial sites is destroyed when the host crystal is subjected to fields such as strain fields, magnetization fields or a combination of both as may be appreciated from Figs. P2 through P4. In this case, the interstitials will preferentially occupy …

The Morphology Of Cellular Precipitation In Magnesium Rich Magnesium-Aluminum Alloys, Jyong Shi Cho

Doctoral Dissertations

"The morphology of cellular precipitation in a Mg-9wt. %AI alloy has been investigated by light and electron microscopy. A study of the early stages of the cellular precipitation process indicated that cellular precipitate structure forms in Mg-Al alloys by Fournelle and Clark mechanism. "Replacive" motion indicative of the Tu and Turnbull mechanism for cellular precipitation was not seen"--Abstract, page 1.

A Study Of The Feasibility In Obtaining The Kinetics Of Various Ordering Phenomena Of The Iron Aluminum System Utilizing The Mössbauer Effect, Lloyd Rollan Chapman

Masters Theses

"The determination of the kinetics of ordering for various ordering phenomena of the Iron-Aluminum system utilizing exclusively the Mössbauer effect technique is shown to be infeasible for all but a highly restrictive consideration from experimental as well as theoretical evidence. Also, the possible use of the Mössbauer effect for the analysis of other ordered systems is discussed.

An alternative method for the acquisition of the needed information utilizing diffraction and Mossbauer techniques is presented recognizing the need for a computer fitting analysis of the complex Mössbauer effect spectra. However, at this stage of investigation, no experimental work has been performed …

Precipitation Of Carbon From Martensite In Ductile Iron, Devendra Ratilal Majmundar

Masters Theses

"Since metallographic studies of quenched and tempered cast iron have indicated that the carbon might precipitate directly as graphite rather than as carbides which are found in steels, this investigation used the Debye-Scherrer x-ray diffraction technique to examine electrolytically extracted residues from quenched and tempered ductile cast iron samples to determine if cementite was present. The precipitation of carbon in quenched samples of this ductile cast iron was found to be similar to the precipitation process in steels. Cementite was identified during the early stages of the tempering process when the tempering temperature was 800 degrees F, 900 degrees F, …

Characterization Of A Mexican Halloysitic Clay And Behavior In Dry Pressing, Jesus L. Derat

Masters Theses

"A Mexican clay, intended to be used as refractory raw material, was identified. Problems encountered in the characterization of halloysitic clays are discussed and emphasis is made on the use of the electron microscope (scanning or transmission type) as a definite evidence of the existence of halloysite due to its unique morphology within the kaolinite group of clay minerals.

Beneficiation of this particular clay was carried out on a small scale hydrocyclone equipment and the results are discussed.

In an attempt to increase the green density in dry pressing of this halloysitic clay, mixtures with grog were prepared using different …

The Effect Of Gating On Soundness Of Al-Alloy Permanent Mold Castings, Dinesh Shantilal Patel

Masters Theses

"This thesis describes the step by step approach to the design of a gating system for the production of sound plate castings in permanent molds. Castings of different thicknesses were produced, utilizing various gating systems, and examined radiographically to evaluate the effectiveness of these gating systems in the production of sound castings. A gating system which allows metal to enter the mold cavity with no turbulence and which establishes proper temperature gradients in the casting will produce sound permanent mold castings"--Abstract, page ii.

The Effect Of Porosity On Strength Degradation In Thermally Shocked Alumina, Russell David Smith

Masters Theses

"Strength degradation and crack propagation in Al₂O₃ are shown to depend on the initial strength and porosity of the material. Specimens were fabricated containing between 0 and 5% induced cylindrical, two dimensional, and spherical porosity. The strengths of the various porosity samples decreased discontinuously at a critical quenching temperature. No difference was observed in the critical temperature for the various aluminas; initial strength decrease occurred between 165°C and 175°C temperature differential. The strength retained after thermal shock decreased with increasing initial strength. The degree of damage sustained upon shocking was also characterized by crack density and crack …

Initial Surface Reactions And Nucleation Kinetics Of Boron On Atomically Clean Molybdenum Substrates, Richard Eugene Moore

Doctoral Dissertations

"A study of the chemical vapor deposition (CVD) of boron from boron triiodide (BI₃) on molybdenum has been done with field emission microscopy (FEM) and low energy electron diffraction (LEED).

A correlation of the efficiency by which BI₃ is effectively dissociated to form adsorbed boron, and the temperature of the substrate has been shown through work function measurements on the boron covered molybdenum field emitter surfaces. The boron-induced work function change of molybdenum has been shown to be in agreement with a theoretical model which predicts positive, as well as negative work functions for adsorbate-substrate systems. It …

Prebainitic Phenomena In Aisi 86b80 And 0.8c-5.3ni Steels, Chung Lim

Doctoral Dissertations

"An ultrasonic investigation shows that the prebainitic kinetics of AISI 86B80 and 0.8C-5.3Ni steels follow t^2/3 and or t¹ time laws in the lower bainite temperature region. The data analysis indicates that these kinetics signal carbon segregation to dislocations. The simple time laws are interrupted at the bainite start time. It is shown that at this time the carbon depleted regions around dislocations transform martensitically. The lower bainite reaction is thus initiated by the formation of supersaturated ferrite through carbon segregation and the subsequent local martensitic transformation"--Abstract, page iii.

A New And Direct Process For The Reduction Of Lead Sulfide, Rolando Oscar Fernandez

Masters Theses

"The direct reduction of lead sulfide concentrates by iron was investigated. An oxygen-bearing flux was shown to be a necessary ingredient for complete reduction of the concentrate. The effects of time and temperature on lead recovery were studied. Only a trace amount of sulfur dioxide is evolved during reduction, which is in agreement with thermochemical calculations"--Abstract, page ii.

Formation And Densification Of Cadmium Manganese Ferrite, B. W. Jong, P. D. Ownby

Materials Science and Engineering Faculty Research & Creative Works

Formation of Ni-ferrite, Mn-ferrite, NiZn-ferrite, Zn-ferrite and Mg-ferrite have been investigated using X-ray diffraction analysis. Jander's diffusion equation described the data from these investigations over a portion of the temperature ranges studied. However, the reaction mechanisms and sequences involved in the formation of mixed ferrites have not been well defined in the literature. The purposes of this investigation were: ( 1) To further the understanding of the formation of CdMnferrite by studying first the kinetics of the formation of Cd-ferrite and Cd-manganite, which provides a basis for understanding the details of the mixed CdMn-ferrite reaction and to obtain the optimum …

Oxidation Of Tetragonal Pbo In Air, Charles A. Sorrell

Materials Science and Engineering Faculty Research & Creative Works

Isothermal oxidation of tetragonal PbO in air produced multiphase assemblages with apparent equilibrium compositions which varied linearly with temperature from PbO1.548 at 286°C to PbO1.333 at 351°C. Oxidation at each temperature was relatively rapid to PbO1.40 and very slow from PbO1.40 to apparent equilibrium values. Pseudocubic PbO1+x, with compositions between PbO1.41 and PbO1.57, was indexed on a cubic unit cell at the lower O/Pb ratios and on a tetragonal unit cell at the higher ratios. Linear changes in lattice parameters and deviation from cubic symmetry accompanied reversible oxidation and reduction of the phase. Pseudocubic PbO1+x was reduced irreversibly to Pb3O4 …

Oxidation State Control Of Volatile Species In Sintering, P. D. Ownby

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Polynary Silicon Arsenic Chalcogenide Glasses With High Softening Temperatures, H. E. Anthonis, N. J. Kreidl, W. H. Ratzenboeck

Materials Science and Engineering Faculty Research & Creative Works

The introduction of Ag in SiAsTe glasses permits the incorporation of Se, otherwise volatile and/or degradable as a constituent in Si-containing chalcogenide glasses. SiAsAgTeSe glasses exhibit much higher softening ranges and glass transition temperatures than encountered in known chalgogenide systems. A glass Si35As15Ag10Te20Se20 had the viscosity log ν = 13 at about 500°C, as compared to 370°C for the base glass Si35As25Te40, the viscosity of log ν = 9.8 at about 560°C, as compared to 442°C for the base glass. Phase separation occurs in the system SiAsAgTeSe and becomes manifest in two glass transitions indicated by changes in the slopes …

Premartensitic Elasticity Of Fe-Ni Invars, Bryce Linn Shriver

Doctoral Dissertations

"The premartensitic temperature dependence of ultrasonic wave propagation in Fe-30 pct Ni polycrystals and Fe-32 pct Ni single crystals was measured by using a continuous wave technique. As the temperature was lowered to within 10°C of the M_s, a nonlinear decrease of the relative shear velocity was observed. This effect is related to dislocation stacking fault instabilities which may trigger the martensitic phase transformation. In addition, the single crystals show a frequency dependence of the shear elastic constant C' well above the M_s. The dispersion is believed to be caused by fluctuations in the anisotropic molecular …

Sintering And Microstructure Control Of A Ferrimagnetic Mn-Zn Ferrite Spinel, Joel Keith Michel

Masters Theses

"The effect of minor additions of CaO dopant to a manganese zinc ferrite – Zn_.25Mn_.75 Fe_2.17 O_4.0 - on its grain growth and densification kinetics in air at 1250°C., 1300°C., and 1350°C. was studied. Grain growth was controlled over a range of dopant levels. At a sintering temperature of 1350°C. and time of six hours a ferrite with the smallest dopant addition was sintered to the highest density - 98% of theoretical. Under the same sintering conditions ferrites with higher dopant levels also sintered with normal growth but sintered to lower densities.

Due to discontinuous …

The Morphology Of The Cellular Precipitation Reaction In A Pb-3.0 Wt% Sn Alloy, Federico Sequeda Osorio

Masters Theses

"The complete development of the cellular precipitation structure at selected grain boundaries in a Pb-3.0 wt% Sn alloy during aging at 34°C and 23°C was investigated by light microscopy. The cellular structure in this alloy consists of lamellae of solute depleted lead solid solution and lamellae of ß tin precipitate. The cellular precipitation reaction begins by local migration of a grain boundary with concomitant grain boundary precipitation of ß tin. The grain boundary bows around the ß tin grain boundary precipitates which then begin to lengthen in the direction of boundary migration thus forming the precipitate lamellae of the cell. …

Polynary Silicon Tellurium Glasses, Henry Edward Anthonis

Masters Theses

"The introduction of Ag into Si-As-Te glasses permits the incorporation of Se, otherwise volatile and/or degradable as a constituent in Si-containing chalcogenide glasses. Si-As-Ag-Te-Se glasses exhibit much higher softening ranges and glass transition temperatures than encountered in known chalcogenide systems. A glass Si₃₅As₁₅Ag₁₀Te₂₀Se₂₀ had the viscosity log η =13 at about 500°C, as compared to 370°C for the base glass Si₃₅As₂₅Te₄₀, the viscosity of log η = 9.8 at about 560°C, as compared to 442°C for the base glass Si₃₅As₂₅Te_{40 …}

The Effect Of Impurities And Additives On The Electrowinning Of Zinc, Haruhisa Fukubayashi

Doctoral Dissertations

"The effect of various impurities, commonly found in zinc electro-winning solutions, on the surface morphology of deposited zinc was investigated. Individual additions of the impurities Al, Ag, Cd, Co, Cr, Cu, Ge, Mn, Ni, Sb, Sn, Ti, PbO₂ , PbSO₄, and HCl were studied. In a few cases additives of animal glue, gum arabic, and Na₂SiO₃, were used individually or in combination, to determine their effect on the surface structure of the deposited zinc. Comparisons were then made with deposits from a pure electrolyte consisting of H₂SO₄ and Zn⁺², 200 and 65 g/l, respectively. The zinc was deposited on a …

Concentration By Sorting : Feasibility Determination By Radial Distribution Analysis, Robert M. Doerr

Masters Theses

"A method was developed for determining certain factors for assessing the feasibility of sorting fragments of an inhomogeneous solid to concentrate a species. These factors are the typical size of zones in which the grade exceeds a selected value, and the recovery potentially achievable by sorting fragments of such size"--Abstract, page iii.

Effects Of Cr-Plating And Environment On The Cracking Of Low Alloy Steels At High Temperatures, Robert C. Tooke

Doctoral Dissertations

"The cracking of low alloy Cr-Mo-V steels under cyclic stress at 1000-1100°C. was studied using a specially designed test apparatus. The results obtained from specimens plated with hard chromium are compared to those of unplated specimens. Tests conducted in gas mixtures of carbon monoxide and carbon dioxide showed that a high CO/CO₂ ratio retards cracking in both plated and unplated specimens. Both external and internal oxidation are used to explain these results. Inherent microcracks in the hard chromium plating promoted cracking in all CO/CO₂ environments. It was also found that these steels are severely embrittled in the presence …

Grain Boundary Diffusion In Ionic Crystals, Kulwant Singh Sabharwal

Doctoral Dissertations

"The diffusion of ¹³¹I in single crystals and along the tilt grain boundaries of pure and calcium chloride doped (142±5 ppm) bicrystals of sodium chloride, grown by Czochralski technique, was investigated using a microtome sectioning technique. Results on bulk diffusion in pure NaCl agree well with the results of earlier investigators and are represented by the D=(504 cm²/sec)exp (-2.27 ev/kT). Enhanced diffusion of ¹³¹I is observed along the grain boundaries and the presence of the dopant lowers the grain boundary diffusivity over the entire temperature range of 430ºC - 570ºC studied in the present investigation. Thermal activation and electrical polarization …

Synthesis And Properties Of Cadmium Manganese Ferrites, B. W. Jong

Doctoral Dissertations

"The formation sequence of (Cd,Mn,Fe) (Mn,Fe)₂O₄ from the individual oxides,x CdO + (1-x) MnCO₃ + α-Fe₂O₃,was found by X-Ray diffraction. Cd(Mn,Fe)₂O₄ was formed completely from CdO·Fe₂O₃ and CdO·Fe₂O₄ at 900°C and reacted with MnFe₂O₄ for 0 < x < 0.5 and with α-Fe₂O₃ for 0.5 < x < 1.0 to form a single phase of (Cd,Mn,Fe) (Mn,Fe)₂O₄ at 1150°C. This is the first time that the details involved in the formation sequence of CdMn-ferrite have been shown. A mixture of 0.5 CdO + 0.5 MnCO₃ + α-Fe₂O₃ was calcined at 900°C for 2 hrs forming Cd(Mn,Fe)₂O₄ with no Cd present in the other phases. Sintering was accomplished at 1150°C for 30 minutes forming a single phase of Cd₀.₅Mn₀.₅Fe₂O₄ with a bulk sintered density of 98-99% of the X-Ray density. The rate of changing density followed the relationship, p = K ln t + c, at temperatures between 1050°C and 1300°C. Magnetic properties of CdₓMn₁₋ₓFe₂O₄ were affected by composition x. A relationship, B = gx + h, was found between maximum magnetic flux density B and composition x at room temperature for 0 <̲ x <̲ 0.3. This was rationalized by a modification of Néel's theory. The maximum magnetic flux density decreased with increasing cadmium concentration for 0.3 < x <̲ 0.5. This decrease was attributed to the changing direction of the magnetic moment in the octahedral site sub-lattice according to the superexchange theory. No magnetic properties were observed due to the formation of a compensated antiferromagnetic phase for 0.5 < x <̲ 1.0. Maximum magnetic flux density increased with bulk density, while the coercive force decreased with the grain growth and the initial permeability increased with the bulk density and grain size. A stator core used for a-c electric motor application was formed by pre-sintering at 900⁰C for 2 hrs. Slots were then sawed with a tungsten carbide blade and final sintering was accomplished at 1150⁰C for 1 hr"--Abstract, pages iii-iv.