Materials Science and Engineering Commons^™

Improving Solar Cell Performance Using Cdse/Zns Core/Shell Quantum Dots In A Spectral Conversion System, Buddy Bump

Materials Engineering

Solar cells have been found to absorb light more efficiently and effectively when the energy of incoming photons matches the electronic band gap of the solar cell. Spectral conversion of light from UV to lower energy wavelengths can improve solar cell efficiency an estimated 14.5%. Cadmium Selenium/Zinc Sulfide Core/Shell quantum dots have been successfully embedded in PDMS silicone elastomer. Using a Keithley 2400 Electrometer with Labview software, voltage and current characteristics have been recorded in steps of 10 mV with a wait time of 250 ms on a commercially available solar cell using an artificial solar spectrum created by a …

Morphology And Roughness Of Al2o3 On Ferritic Stainless Steel Foil For Diesel Catalytic Converter Applications, Megan Butala

Materials Engineering

The improved thermal properties of metal-substrate catalytic converters enable effective catalysis sooner after ignition than traditional ceramic monoliths, resulting in less harmful emissions. ACAT Global, a manufacturer of stainless steel catalytic converters, uses ferritic stainless steel substrates for low temperature catalytic converters for diesel automobiles. Production begins with an oxidizing heat treatment to increase surface roughness. The success of the second production step, the application of catalyst-containing ceramic slurry (washcoat), depends on the surface roughness that results from oxidation. Formation of the primary oxide of interest, alumina (Al₂O₃), is controlled by the stainless steel foil composition, …

Discontinuous Grain Boundaries Of Forged René 41, Steven Crump

Materials Engineering

Forged components must pass a grain size specification (grain size, distribution) for acceptance in an application. The varying amounts of plastic deformation during forging can lead to abnormally large recrystallized grain sizes in certain regions of the part, which will not pass specification. The question exists whether these abnormally coarse grains are truly comprised of poly crystalline fine grains with grain boundaries resistant to etching techniques. To investigate this abnormal grain size effect, a cross section of a forged René 41 nickel-based superalloy aircraft engine ring was cut and sectioned into six segments. Those segments were then prepared for microstructural …

Analyzing The Corrosion Resistance Of Ni-Shield 200 Coatings At Different Temperatures When Exposed To Sulphuric Acid, Alex Hussinger

Materials Engineering

Six steel samples each were twin wire arc sprayed with Hastelloy C-276 or Nickel-Shield 200 coatings approximately 0.020″ thick. These samples were then cut into 3″ by 3″ squares. A 2″ diamond grit hole saw was used to abrade and polish to a smooth surface a ring in the middle in order to get an O-ring mechanical seal. The samples were then weighed and loaded into a jig that started from the bottom up with a stainless steel plate, then the sample, then a Viton O-ring, a ¾″ thick glass plate with a 1 3/4″ hole cut in it, another …

Al2O3 Oxide Morphology For Two Fe-Cr-Al Stainless Steel Foils Used In Gasoline Engine Catalytic Converters, Jennifer Suiter

Materials Engineering

Corrugated 0.05 in thick strips of Fe-Cr-Al ferritic stainless steel samples with 4% and 6% aluminum were heat treated, and the resulting Al₂O₃ oxide was analyzed using SEM imaging. Three heat treatment cycles were carried out for each sample. The heat treatments were based on future metal-substrate catalytic converter processing prior to applying the washcoat Each heat treatment started with a 90 minute ramp from room temperature to 538°C and a 32.5 minute ramp from 538°C to 899°C. The three different dwell periods at 899°C were 4 hours, 6 hours, and taking a sample out every hour …

The Mitigation Of Eutrophication Using Microporous Polymer Membranes To Control Algae Growth, Christopher R. Riley

Materials Engineering

A system was designed to mitigate the accelerated process of anthropogenic eutrophication. This system aimed to contain Chlorella Vulgaris microalgae cells within an enclosed polymer membrane pouch while allowing for water and nutrients to diffuse through the pouch. As a test model, a 10 gallon aquarium was partitioned into three sections using polycarbonate membranes with 1 micron pore diameters. Each section was then gradually filled with a deionized water and Bristol solution recommended for microalgae growth. Phosphate and nitrate were added to Section A of the aquarium and allowed to diffuse throughout the tank. A water pump was used to …

Finite Element Modeling Of Ballistic Impact On A Glass Fiber Composite Armor, Dan M. Davis

Master's Theses

Finite Element Modeling of Ballistic Impact on a Glass Fiber Composite Armor

Dan Davis

Experiments measuring the ballistic performance of a commercially available fiberglass armor plate were used to guide the development of constitutive laws for a finite element model of the impact. The test samples are commercially available armor panels, made from E-glass fiber reinforced polyester rated to NIJ level III. Quasi-static tensile tests were used to establish material properties of the test panels. These properties were then used to create models in the explicit finite element code LSDYNA.

Ballistic impact testing of the panels was conducted using a …

Multipolymer Interactions In Bulk Heterojunction Photovoltaic Devices, Grant Olson

Physics

Multipolymer photovoltaics, single layer devices made up of multiple photoactive polymers, can create organic photovoltaics (OPVs) with a wider spectral response than single polymer systems without the difficult fabrication of a tandem. Our group has successfully created multipolymer solar devices with 2% power conversion efficiency. We have analyzed the optical and electrical properties of these devices, and found that it may be possible for polymers to assist each other with charge extraction, though combining polymers disrupts single polymer crystallinity.

Creating A Solar Cell Array From A Single Silicon Wafer, Samyukta Gade, Roderick Marstell

Materials Engineering

Two different processes to create multi-celled solar panels from single wafers were made and implemented. To do this, the cells must not have a common ground, and both designs use different approaches to solve this problem. One utilizes a 2.9 µm deep n-type well within a 10.74 µm deep p-type well in an n-type wafer. There are two cells in series, which has a theoretical voltage of 1 V. The cells are connected in series with 1.9 µm thick gold traces. Any area that the gold is not in contact with the silicon has a .5 µm layer silicon dioxide …

The Effects Of Concentration, Stir Rate, And Processing Temperature On The Iridescence Of Polymethyl Methacrylate Nanoparticles, David Baruela

Materials Engineering

Synthetic opals were synthesized by creating polymethyl methacrylate (PMMA) nanospheres in order to determine which conditions would create the best iridescent samples. The factors affecting the iridescence were nanosphere concentration, stir rate, and processing temperature. PMMA solutions were made by adding 17 mg of granular azobis to a solution of 16 mL of distilled water with 3 mL of methyl methacrylate (MMA). The solution was stirred at different rates, slow and fast, and different temperatures, 70 °C and 90 °C, under a constant flow of nitrogen gas for 40 minutes until the polymerization reaction was complete. Glass substrates were prepared …

Fabricating Replacement Glass Prisms For The Piedras Blancas Lighthouse, Daniel Garcken

Materials Engineering

The objective of this project was to design and create a process for manufacturing replacement glass prisms for the Piedras Blancas lighthouse and several other lighthouses nationwide. The prisms were designed to be in multiple metal arrays spread across the floor of the beacon room (the topmost room of the lighthouses). The prisms functioned to transmit extra, radiant light from the beacon light through the floor of the beacon room and disperse it into the maintenance room below. Using computer aided drafting (CAD) software, an original prism was measured and modeled; the corresponding mold was also modeled. G-codes for controlling …

Effects Of Abrasive Particles On The Projected Fatigue Life Of Nylon Climbing Rope, Casey Johnson, Charlie Klonowski

Materials Engineering

When climbing rope is used outdoors, it is exposed to foreign particles such as sand and silt. These particles can potentially work their way through a rope’s sheath and damage the load bearing core decreasing the rope’s strength without exhibiting obvious wear. This project quantified the effect of abrasive particles on the fatigue life of nylon climbing rope. The experimental design involved 18 pieces of static nylon rope of kernmantle construction. 9 of these samples were heavy agitated in a slurry of water, silt, sand and soil, and left to sit for 24 hours. The remaining 9 samples were submerged …

Synthesis Of White Cadmium-Selenium Quantum Dots, Kyle Reilly

Materials Engineering

A process was developed for the synthesis of cadmium-selenium quantum dots that fluoresce at multiple wavelengths, giving a white color to the solution. The process involved making a selenium pre-cursor, then a cadmium precursor, then injecting the selenium precursor into the cadmium precursor and extracting a sample. Once the a repeatable process for synthesizing white quantum dots was developed, the absorption and fluorescence was measured and recorded over a period of two weeks. In the development of the process, the key variables were the temperature of the cadmium precursor and the time between injecting the selenium precursor and extracting the …

Characterization Of Positive Macrosegregation At The Subsurface Of Direct-Chill Cast 7050 Aluminum Forging Billets, Aaron Youril

Materials Engineering

Segregation of alloying elements during casting of forging billets may persist to the final forged component leading to unacceptable surface appearance. Determination of the elements or compounds that segregate is the essential first step to solving this problem. Differential Scanning Calorimetry (DSC) was used to determine a composition profile of the macrosegregation occurring at the subsurface of an as-cast 7050 aluminum alloy billet. Data collection was carried out by separating 10 to 20 mg samples from the outer centimeter along the radius of the billet, as well as samples from the bulk interior of the billet for comparison with the …

Analysis Of Failed Forging Saddling Mandrels And Process Improvements For Increased Mandrel Lifespan, Brock Costalupes

Materials Engineering

This project seeks to increase the lifespan of steel mandrels used by Schlosser Forge in the saddling process, which is part of the production of forged rings for the aerospace and power generation industries. All saddle mandrel samples were taken from used 4340 steel mandrels. Hardness profiles were measured across rectangular bars cut from the transverse direction of a completely fractured piece of a 7″ diameter mandrel. The hardness near one outer surface of the tested bar was 36 HRC and gradually decreased to 30.5 HRC at the opposite surface. Macroscopic examination of the primary fracture surface along with light …

Effect Of Heating Temperature, Heating Time And Initial Microstructure On Recrystallization Of Waspaloy During Heating For Forging, Marissa Hill

Materials Engineering

A fine, uniform grain size is required for creep limited Waspaloy in aircraft engine applications. Upon heating, Waspaloy does not always recrystallize in a uniform manner resulting in occasional large grains with a majority of the grains meeting the grain size requirements. Waspaloy’s microstructure was analyzed with different heat treatments and in the as-forged condition. The strengthening mechanism is the gamma prime phase. The gamma prime solvus temperature is 1908°F so the different heat treatments were determined around that temperature, as well as the forging temperature range of 1800-2150°F. At the 1850°F heat treatment, the microstructure recrystallized with small grains, …

Corrosion Of Stainless Steel 316l And Astm F75 Cobalt Chromium Alloy During Immersion Testing In Silver Salt Solutions, Meagan Higgins

Materials Engineering

This study evaluates the potential effects of silver salts on biocompatible metals used for prostheses during the chemical reduction process to produce a silver antimicrobial layer on the metal’s surface. Samples of two biocompatible metals were obtained: Stainless Steel 316L and ASTM F75 Cobalt Chromium Alloy. Three different silver salts were also acquired: silver nitrate, silver sulfadiazine, and silver chloride. Specimens of each metal were cut to size using a 4-1/2 inch aluminum oxide, 40 grit, cut off wheel for metal, attached to a Dewalt Angle Grinder. The biocompatible metal samples were then subject to either Solution 1, water with …

Correlation Between 90o Tensile And 90o Flexural Properties For Thermoplastic Based Carbon-Fiber Composites, Amy Lautenbach

Materials Engineering

Thermoplastic matrix composites containing carbon fibers and 4 different resins (TP 1-TP 4) were tested in tension with the fibers at 90 degree to the longitudinal axis following ASTM D 3039-00. The tensile strengths varied from 5.07-13.87 ksi with TP 1 as the strongest, and TP 4 as the weakest. SEM images were taken of the fracture surface of the samples to explore the fiber-matrix interaction. The SEM images showed significantly more wetting of the fibers in the higher strength materials. The SEM images of the two stronger materials showed resin coating the fibers even after fracture while the two …

Feasibility Analysis For Electrically-Powered Hoverboard, Cameron Chan, Jason Cortez, Jay Lopez

Aerospace Engineering

Composite materials are engineered by combining two or more constituent materials with significantly different physical or chemical properties in such a way that the constituents are still distinguishable, and not fully blended. Due to today’s high rising prices of gasoline and aviation fuel costs, many manufacturers have turned to the use of lightweight composites in their designs due to the advantages of the composite material, which include outstanding strength, excellent durability, high heat resistance, and significant weight reduction that the composite material properties hold. The purpose of this project is to design and construct a composite structure for an electrically-powered …

Lunalight Project: Solar-Rechargeable Led Lantern And Cell Phone Charger, Sean C. Dawson, Michael E. Deagen, Francisco N. Dye, Brian S. Mircheff, Ryan O. Ramelb

Materials Engineering

Today, 1.6 billion people in the world do not have access to grid electricity. Villagers living off the grid in developing nations resort to kerosene lanterns to light their homes. The fumes from burning kerosene are toxic and lead to respiratory illnesses over time. Our sponsor, OneMillionLights, plans to help people to escape poverty by providing them with a clean source of light at night. Children that must work in the fields during the day can use a solar-rechargeable lantern at night to read or study, and street vendors can use the lanterns at night to improve their businesses.

The …

The Design And Fabrication Of A Microfluidic Reactor For Synthesis Of Cadmium Selenide Quantum Dots Using Silicon And Glass Substrates, Peter Robert Gonsalves

Master's Theses

A microfluidic reactor for synthesizing cadmium selenide (CdSe) quantum dots (QDs) was synthesized out of a silicon wafer and Pyrex glass. Microfabrication techniques were used to etch channels into the silicon wafer. Holes were wet-drilled into the Pyrex glass using a diamond-tip drill bit. The Pyrex wafer was anodically bonded to the etched silicon wafer to enclose the microfluidic reactor. Conditions for anodic bonding were created by exposing the stacked substrates to 300V at ~350oC under 5.46N of force. A syringe containing a room temperature CdSe solution was interfaced to the microfluidic reactor by using Poly (dimethylsiloxane) (PDMS) as an …

Characterization Of Mixing In A T-Style Microfluidic Chip, Brian Eric Harley

Master's Theses

The goal of this study is to characterize the mixing that occurs in a microfluidic chip. To characterize the mixing, the minimum length to complete mixing and evolution of mixing will be investigated. There are two types of mixing that occur within a microfluidic channel, diffusion and advection. In the beginning of the microfluidic chip, diffusion is the dominant form of mixing, and in the later portion of the microfluidic chip advection is the dominant form of mixing. The type of design used for this experiment was a zig zag geometry microfluidic chip with channel dimensions of 60 µm X …

Transformational Innovation: Reflections On How To Foster It In Engineering Education Systems, Roger Burton, Lizabeth Schlemer, Linda Vanasupa

Materials Engineering

This paper describes the educators’ disposition that we believe is required for transformational innovation. Innovating in this domain relies on interrupting existing patterns. This interruption requires the conscious recognition of patterns through an active practice of self observation. Though self observation does not necessarily need a collective process, it is served by encountering the diversity of views present in groups. Innovation in this sense consists of a fundamental identity shift in the human system and the innovators themselves. Unlike the processes of problem solving and process improvement, transformational innovation requires insight into the individual and collective attention of the designers. …

A Quantitative Study Of The Weldability Of Inconel 718 Using Gleeble And Varestraint Test Methods, Sean Quigley

Master's Theses

Nickel super alloy Inconel 718 was tested and compared to Haynes 230 using Gleeble and Varestraint mechanical test methods. Hot cracking susceptibility was examined in either alloy using a sub-scale Varestraint test method at 5 augmented strain levels: 0.25%, 05.%, 1%, 2%, and 4%. Maximum crack length, total crack length, and number of cracks were measured for each strain level. Gleeble hot ductility on-heating and on-cooling tests were performed on both alloys. Inconel 718 was tested on-heating at target temperatures of 1600˚F, 2000˚F, 2100˚F, 2200˚F, and on cooling at 1600˚F, 1700˚F, 1800˚F, 1900˚F, and 2100˚F. Haynes 230 was tested on-heating …

Improved Manufacturing Methods Of Bovine Femur Samples For Ultrasonic Testing And Assessment Of Materials Through Contract Angle Measurement, Kevin Mathew Lopez Galang

Biomedical Engineering

At California Polytechnic State University of San Luis Obispo (Cal Poly), the Biomedical Engineering department (BMED) requires its students to take the course listed as “BMED 420: Principles of Biomaterial Designs.” BMED 420 has a required laboratory section every week throughout the duration of the course that is meant to be a supplemental tool for learning. During the lab sections, students perform experiments and exercises that are currently being implemented in the industry. Despite accuracy of the methods and experiments relative to their use in the industry, there is always room for improvement. The objective of this project will illustrate …

Energy - Activities, Jane Qiong Zhang, Linda Vanasupa

Materials Engineering

The document contains activities for students in higher education. These activities are focused on energy issues related to sustainability. It is designed for the general engineering or science audience. Its design is based on the framework of the Fink Taxonomy of Significant Learning. Each activity includes a profile that indicates whether the activity involves direct or indirect information sources, whether the experience is doing or observing and whether it involves individual or group reflection. The profile also includes notes for faculty, an estimate of the time investment, a graphic of the developmental aims with respect to the six areas of …

Fink Taxonomy Of Significant Learning, Jane Qiong Zhang, Linda Vanasupa

Materials Engineering

This document is graphical summary of the framework within the Fink Taxonomy of Significant Learning and the definition of each of the six areas of significant learning.

Sustainable Development, Jane Qiong Zhang, Linda Vanasupa

Materials Engineering

This document is a set of learning materials to support the teaching of Sustainable Development issues particularly related to sustainability in engineering. It is designed for the general engineering or science audience. Its design is based on the framework of the Fink Taxonomy of Significant Learning. The document is a fully-editable set of slides in open source format (pptx) that includes references to targeted learning objectives on each slide and annotations in the notes section of each slide.

Water - Activities, Jane Qiong Zhang, Linda Vanasupa

Materials Engineering

The document contains activities for students in higher education. These activities are focused on water issues related to sustainability. It is designed for the general engineering or science audience. Its design is based on the framework of the Fink Taxonomy of Significant Learning. Each activity includes a profile that indicates whether the activity involves direct or indirect information sources, whether the experience is doing or observing and whether it involves individual or group reflection. The profile also includes notes for faculty, an estimate of the time investment, a graphic of the developmental aims with respect to the six areas of …

Population, Jane Qiong Zhang, Linda Vanasupa

Materials Engineering

This document is a set of learning materials to support the teaching of population issues particularly related to sustainability in engineering. It is designed for the general engineering or science audience. Its design is based on the framework of the Fink Taxonomy of Significant Learning. The document is a fully-editable set of slides in open source format (pptx) that includes references to targeted learning objectives on each slide and annotations in the notes section of each slide.