Materials Science and Engineering Commons^™

Preparation And Lithium Storage Properties Of Carbon Confined Li3Vo4 Nano Materials, Jia-Qi Fan, Huan-Qiao Song, Jia-Ying An, Amantai A-Yi-Da-Na, Mo Chen

Journal of Electrochemistry

Li₃VO₄, as a promising anode material for lithium ion batteries, has been widely studied because of its low and safe voltage, and large capacity. However, its poor electronic conductivity impedes the practical application of Li₃VO₄ particularly at high rates. In this paper, carbon confined Li₃VO₄ nano materials (Li₃VO₄/C) were synthesized by hydrothermal and solid-phase method, and for comparison, the Li₃VO₄ (N) nano materials without carbon confinement and Li₃VO₄ (B) materials were also synthesized by pure solid-phase method. The composition, structure, …

Peg-Water Electrolyte For High-Performance Zinc Iodine Dual-Ion Batteries, Xiao-Feng Qu, Yu-Ting Tang, Xin-Cheng He, Jia-Sheng Zhou, Zi-Heng Tang, Wen-Hua Feng, Jun Liu

Journal of Electrochemistry

Thanks to abundant resource and rapid redox reaction kinetics, iodine is regarded as promising positive materials inthe batteries. However, the shuttling effect due to the high solubility of iodine in the electrolyte makes the performance of battery poor. In this paper, polyethylene glycol (PEG400) and potassium iodide were added into zinc-ion aqueous electrolyte. PEG400 could complex with iodine to reduce the dissolution of iodine, therefore alleviating the formation of soluble triiodide (I₃^–) from iodine and iodide ions. Furthermore, this electrolyte was used in the battery with double carbon cloths as the current collectors, double separators and zinc …

Research Progress And Performance Improvement Strategies Of Hard Carbon Anode Materials For Sodium-Ion Batteries, Xiu-Ping Yin, Yu-Feng Zhao, Jiu-Jun Zhang

Journal of Electrochemistry

This paper systematically summarizes the research progress of hard carbon anode materials in sodium ion batteries(SIBs) and the development of the corresponding sodium storage mechanism in recent years, and reviews the performance improvement strategies of hard carbon materials from the aspects of structural design and electrolyte regulation. The effects of the selection of precursors, carbonization temperature, pretreatment, pore formers, heteroatom doping, material compounding, electrolyte regulation and pre-sodiumization on the sodium storage performance of hard carbon anode materials are briefly described. This paper provides new insights into the design, synthesis and electrolyte
matching of high-performance and low-cost hard carbon materials, and …

Surface Modifications Of Lini0.96Co0.02Mn0.02O2 With Tungsten Oxide And Phosphotungstic Acid, Gang Zhao, Zheng-Liang Gong, Yi-Xiao Li, Yong Yang

Journal of Electrochemistry

With the rapid development of electric vehicles, enormous demands are made for higher energy density, better cycling performance and lower cost of lithium-ion batteries (LIBs). As an important high capacity cathode material for LIBs, the high nickel layered oxide material LiNi_0.8Co_0.1Mn_0.1O₂(NCM811) can reach an energy density of 760 Wh·kg^-1. The ultra-high nickel ternary positive electrode material (LiNi_1-x-yCo_xMn_yO₂, x ≥ 0.90) has a specific capacity of more than 210 mAh·g^-1, and can realize higher energy density. Besides, an ultra-high nickel material …

Preparation And Electrocatalytic Performance Of Feni-Cop/Nc Bifunctional Catalyst, Si-Miao Liu, Jing-Jiao Zhou, Shi-Jun Ji, Zhong-Sheng Wen

Journal of Electrochemistry

Rechargeable zinc-air batteries have gradually attracted much attention worldwide due to their high capacity, high energy density and low price. Oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) correspond to the charging and discharging processes in rechargeable zinc-air battery, respectively. At present, commercial Pt/C and IrO₂ catalysts hinder the large-scale application of zinc-air batteries due to low reserves, high prices and poor stability. Therefore, exploring high performance, low cost and high stability with dual functional catalysts is important for the development of rechargeable zinc-Air batteries. The metal-organic frameworks (MOFs) have high specific surface area, structural stability, good catalytic …

Asymmetric Electrode-Electrolyte Interfaces For High-Performance Rechargeable Lithium-Sulfur Batteries, Jia Chou, Ya-Hui Wang, Wen-Peng Wang, Sen Xin, Yu-Guo Guo

Journal of Electrochemistry

With a high cell-level specific energy and a low cost, lithium-sulfur (Li-S) battery has been intensively studied as one of the most promising candidates for competing the next-generation energy storage campaign. Currently, the practical use of Li-S battery is hindered by the rapidly declined storage performance during battery operation, as caused by irreversible loss of electroactive sulfide species at the cathode, dendrite formation at the anode and parasitic reactions at the electrode-electrolyte interface due to unfavorable cathode-anode crosstalk. In this perspective, we propose to stabilize the Li-S electrochemistry, and improve the storage performance of battery by designing asymmetric electrode-electrolyte interfaces …

Hydrophobicity Optimization Of Cathode Catalyst Layer For Proton Exchange Membrane Fuel Cell, Hao-Jie Chen, Mei-Hua Tang, Sheng-Li Chen

Journal of Electrochemistry

Hydrophobicity of the cathode catalyst layers (CCLs) crucially determines the performance of proton exchange membrane fuel cells (PEMFCs) by affecting the transports of oxygen and liquid water. In this regard, polytetrafluoroethylene (PTFE) is usually used as a hydrophobic additive to facilitate the oxygen and water transports in CCLs. So far, there remains lacking systematic effort to optimize the addition methods of PTFE in CCLs and the mechanisms behind. In this work, the effects of the approaches for PTFE addition and the distribution of PTFE on the mass transport of oxygen and the proton conduction in CCLs were studied by using …

Synthesis And Evaluation Of Organic Additives For Copper Electroplating Of Interconnects, Yue-Hui Zhai, Yi-Xiao Peng, Yan Hong, Yuan-Ming Chen, Guo-Yun Zhou, Wei He, Peng-Ju Wang, Xian-Ming Chen, Chong Wang

Journal of Electrochemistry

Copper interconnects are essential to the functionality, performance, power efficiency, reliability, and fabrication yield of electronic devices. They are widely found in chips, packaging substrates and printed circuit boards, and are often produced by copper electroplating in an acidic aqueous solution. Organic additives play a decisive role in regulating copper deposition to fill microgrooves, and micro-vias to form fine lines and interlayer interconnects. Generally, an additive package consists of three components (brightener, suppressor, and leveler), which have a synergistic effect of super-filling on electroplating copper when the concentration ratio is appropriate. Many works of literature have discussed the mechanism of …

Effect Of Amine Additives On Thermal Runaway Inhibition Of Sic||Ncm811 Batteries, Bo-Wen Hou, Long He, Xu-Ning Feng, Wei-Feng Zhang, Li Wang, Xiang-Ming He

Journal of Electrochemistry

The high energy density of NCM batteries with high nickel content is a key advantage in replacing fossil fuels and promoting clean energy development, at the same time, is also a fundamental cause of serious safety hazards in batteries. Primary and secondary amines can lead to ring-opening polymerization of common ethylene carbonate electrolytes, resulting in an isolation layer between the cathode and the anode, and improving the thermal safety of the battery. In this work, the safety of batteries is considered both at the material level and at the cell level, based on the chemical reactions between amines and the …

Effects Of Traps On Photo-Induced Interfacial Charge Transfer Of Ag-Tio2: Photoelectrochemical, Electrochemical And Spectroscopic Characterizations, Zhi-Hao Liang, Jia-Zheng Wang, Dan Wang, Jian-Zhang Zhou, De-Yin Wu

Journal of Electrochemistry

In the field of metal-semiconductor composites based plasmon-mediated chemical reactions, a clear and in-depth understanding of charge transfer and recombination mechanisms is crucial for improving plasmonic photocatalytic efficiency. However, the plasmonic photocatalytic reactions at the solid-liquid interface of the electrochemical systems involve complex processes with multiple elementary steps, multiple time scales, and multiple controlling factors. Herein, the combination of photoelectrochemical and electrochemical as well as spectroscopic characterizations has been successfully used to study the effects of traps on the photo-induced interfacial charge transfer of silver-titanium dioxide (Ag-TiO₂). The results show that the increase of surface hydroxyl groups may …

Recent Progress Of Bifunctional Electrocatalysts For Oxygen Electrodes In Unitized Regenerative Fuel Cells, Tian-Long Zheng, Ming-Yu Ou, Song Xu, Xin-Biao Mao, Shi-Yi Wang, Qing-Gang He

Journal of Electrochemistry

Unitized regenerative fuel cells (URFCs), which oxidize hydrogen to water to generate electrical power under thefuel cells (FCs) mode and electrolyze water to hydrogen under the water electrolysis (WE) mode for recycling, areknown as clean and sustainable energy conversion devices. In contrast to the hydrogen oxidation reaction (HOR) andhydrogen evolution reaction (HER) on the hydrogen electrode side, the sluggish kinetics of oxygen reduction reaction(ORR) and oxygen evolution reaction (OER) on the oxygen electrode side requires highly efficient bifunctional oxygencatalysts. Conventional precious metal oxygen catalysts combine Pt and IrO₂ with excellent ORR and OER activities toachieve bifunctional electrocatalysis performance, but …

Band Alignments Of Metal/Oxides-Water Interfaces Using Ab Initio Molecular Dynamics, Yong-Bin Zhuang, Jun Cheng

Journal of Electrochemistry

Band alignments of electrode-water interfaces are of crucial importance for understanding electrochemical interfaces. In the scenario of electrocatalysis, applied potentials are equivalent to the Fermi levels of metals in the electrochemical cells; in the scenario of photo(electro)catalysis, semiconducting oxides under illumination have chemical reactivities toward redox reactions if the redox potentials of the reactions straddle the conduction band minimums (CBMs) or valence band maximums (VBMs) of the oxides. Computational band alignments allow us to obtain the Fermi level of metals, as well as the CBM and VBM of semiconducting oxides with respect to reference electrodes. In this tutorial, we describe …

Scanning Photoelectrochemical Microscopic Study In Photoinduced Electron Transfer Of Supramolecular Sensitizers-Tio2 Thin Films Systems, Sheng-Ya Zhang, Min Yao, Ze Wang, Tian-Jiao Liu, Rong-Fang Zhan, Hui-Qin Ye, Yan-Jun Feng, Xiao-Quan Lu

Journal of Electrochemistry

Crafting charge transfer channels at titanium dioxide (TiO₂) based photoanodes remain a pressing bottleneck in solar-to-chemical conversion technology. Despite the tremendous attempts, TiO₂ as the promising photoanode material still suffers from sluggish charge transport kinetics. Herein, we propose an assembly strategy that involves the axial coordination grafting metalloporphyrin-based photosensitizer molecules (MP) onto the surface-modified TiO₂ nanorods (NRs) photoanode, forming the composite MP/TiO₂ NRs photoelectrode. As expected, the resulted unique MP_B/TiO₂ NRs photoelectrode displays significantly improved photocurrent density as compared to TiO₂ NRs alone and MP_A/TiO₂ NRs photoelectrode. Scanning …

The Modernization Of Large Power Transformer Tanks, Babajide O. Williams

Electronic Theses and Dissertations

Due to the current demands placed on the power grid in terms of climate change, increasing urbanization, and terrorist attacks, the U.S. government in response to these demands, mandated that all the grid components be modernized in order to increase their reliability. As a critical component of the grid, Large Power Transformers (LPTs) play a key role in ensuring sustainable power generation and distribution. A literature search performed in this work and the analysis of data retrieved from the search showed that the tanks of these LPTs are critical to their durability, longevity, and reliability. Therefore, the reliability of LPTs …

Design, Modeling, And Testing Of A Novel Inductor For Electric Vehicles: Iron Nitride Soft Magnetic Composites, Sydney F. Fultz-Waters, Jacob Krynock

Materials Engineering

New technology for electric vehicles (EVs) must meet the requirements of higher energy usage, lower costs, and more sustainable source materials. One promising material for EV power system components is iron nitride (IN) soft magnetic composites (SMCs) because of their competitive magnetic properties and high abundance of the source materials. As part of an ongoing program at Sandia National Laboratories, this project focused on using computer modeling to optimize the prototyping process for an iron nitride SMC toroidal inductor to reach a target inductance of 600 μH. Four inductors with different combinations of wiring (26 AWG and 20 AWG) and …

Exploring The Potential Of Pavegen’S Kinetic Energy Generating Floor For Sustainable Energy Solutions: A Proposal For Cal Poly Slo, Brandon J. Cuneo

Construction Management

This paper proposes the installation of Pavegen's kinetic energy generating floors at Cal Poly’s campus as a sustainable energy solution. Pavegen has developed a pioneering technology that converts footsteps into clean and renewable energy. The versatility of these floors is demonstrated through successful implementations in various settings, such as transportation hubs and public spaces, generating power from foot traffic. Collaborations with Schneider Electric, installation at Dupont Circle, and integration at Heathrow Airport showcase the potential for sustainable urban infrastructure. This paper outlines research conducted on Pavegen and similar solutions, including communication with company representatives and examining proposed installation locations at …

P-Doped Ru-Pt Alloy Catalyst Toward High Performance Alkaline Hydrogen Evolution Reaction, Rong-Qin Huang, Wei-Ping Liao, Meng-Xuan Yan, Shi Liu, Yuan-Ming Li, Xiong-Wu Kang

Journal of Electrochemistry

Electrocatalytic water splitting represents grand promise for hydrogen fuel in modern energy equipment, and the design and fabrication of higher performance catalysts are at the central. Herein, we report the sequential phosphorus (P)-doping into ruthenium (Ru) nanoparticles (Ru-P/C) by thermal annealing of Ru nanoparticles in phosphine (PH₃) atmosphere and deposition of extremely low concentration of platinum (Pt) to obtain P-doped Ru-Pt alloy catalyst supported on carbon nanotubes (CNTs), which is denoted as (Ru-P)#Pt/C. The data by X-ray diffraction spectroscopy and transmission electron microscopy show that the Ru nanoparticles existed in the form of hexagonal close-packed (hcp) phase with …

Deep Euteceic Solvents-Assisted Synthesis Of Novel Network Nanostructures For Accelerating Formic Acid Electrooxidation, Jun-Ming Zhang, Xiao-Jie Zhang, Yao Chen, Ying-Jian Fan, You-Jun Fan, Jian-Feng Jia

Journal of Electrochemistry

Deep eutectic solvents (DESs) have been reported as a type of solvent for the controllable synthesis of metal nanostructures. Interestingly, flower-like palladium (Pd) nanoparticles composed of staggered nanosheets and nanospheres are spontaneously transformed into three-dimensional (3D) network nanostructures in choline chloride-urea DESs using ascorbic acid as a reducing agent. Systematic studies have been carried out to explore the formation mechanism, in which DESs itself acts as a solvent and soft template for the formation of 3D flower-like network nanostructures (FNNs). The amounts of hexadecyl trimethyl ammonium bromide and sodium hydroxide also play a crucial role in the anisotropic growth and …

Fe Nanoparticles Encapsulated In N-Doped Porous Carbon For Efficient Oxygen Reduction In Alkaline Media, Chun-Yan Li, Rui Zhang, Xiao-Jie Ba, Xiao-Le Jiang, Yao-Yue Yang

Journal of Electrochemistry

Rational design and synthesis of non-precious-metal catalyst plays an important role in improving the activity and stability for oxygen reduction reaction (ORR) but remains a major challenge. In this work, we used a facile approach to synthesize iron nanoparticles encapsulated in nitrogen-doped porous carbon materials (Fe@N-C) from functionalized metal-organic frameworks (MOFs, MET-6). Embedding Fe nanoparticles into the carbon skeleton increases the graphitization degree and the proportion of graphitic N as well as promotes the formation of mesopores in the catalyst. The Fe@N-C-30 catalyst showed the excellent ORR activity in alkaline solutions (E₀ = 0.97 V vs. RHE, E_{1/2 …}

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

Cobalt/Carbon Composites As Sulfur Hosts For High-Performance Lithium-Sulfur Batteries, Yun-Rui Yang, Huan-Huan Dong, Zhi-Qiang Hao, Xiang-Xi He, Zhuo Yang, Lin Li, Shu-Lei Chou

Journal of Electrochemistry

Lithium-sulfur (Li-S) battery is one of the promising energy storage devices because of its high energy density. However, the sulfur cathode suffers from sluggish electrochemical reaction kinetics, slow charge transfer, large volume expansion and severe shuttle effect of lithium polysulfides inevitably resulting in low reversible capacity, poor rate performance and short cycle life, limiting its practical applications. Herein, the recent progress of cobalt/carbon composites, including cobalt nanoparticles and cobalt single atoms, as the sulfur host materials in Li-S batteries is overviewed. In general, cobalt plays the role of electrocatalyst, which inhibits the shuttle effect of lithium polysulfides, accelerates the electrochemical …

Recent Advances Of Functional Electrolyte Additives For Lithium-Sulfur Batteries, Xiu-Qing Zhang, Shuai Tang, Yong-Zhu Fu

Journal of Electrochemistry

Lithium-sulfur (Li-S) batteries have become one of the most promising next-generation battery systems due to their high energy density and low cost. However, the application of Li-S batteries still faces critical challenges, such as the low conductivities of S and Li₂S, shuttle effect of polysulfides and dendrite growth of Li, etc. The optimization of the electrolyte can ameliorate the electrolyte|electrode interphase, conveniently regulating the parasitic reaction and improving the performance of the resultant batteries. The functional additives in electrolytes provide chances to tune the interphase and even the redox mechanism to improve the performance of the batteries. In …

Metals And Alloys As Catalytic Hosts Of Sulfur Cathode For Lithium-Sulfur Batteries, Zhen-Yu Wang, Xue-Ping Gao

Journal of Electrochemistry

Lithium-sulfur batteries are recognized as one of the most promising next-generation energy storage devices, owing to the high theoretical energy density of 2600 Wh·kg^–1. However, their application has been seriously hindered by the sluggish electrochemical reaction kinetics of elemental sulfur and discharged products (Li₂S₂/Li₂S), and the notorious “shuttle effect” of soluble intermediate lithium polysulfide species, leading to poor cycle stability, low sulfur utilization and inferior coulombic efficiency. Introducing catalytic hosts into sulfur cathode is an efficient path to propel the conversion of sulfur-contained species, thus preventing the dissolution and loss of active-sulfur …

Ultraviolet-Initiated In-Situ Cross-Linking Of Multifunctional Binder Backbones Enables Robust Lithium-Sulfur Batteries, Sha Li, Xiao Zhan, Gu-Lian Wang, Hui-Qun Wang, Wei-Ming Xiong, Li Zhang

Journal of Electrochemistry

Lithium-sulfur (Li-S) batteries show attractive prospects owing to their high theoretical energy density, but their commercialization still faces such challenges as lithium polysulfides shuttling, severe volume change and considerable polarization. These stubborn issues place higher demands on each component in the battery, such as the development of multifunctional binders with superior mechanical properties. Herein, ethoxylated trimethylolpropane triacrylate was firstly introduced into sulfur cathodes, and in-situ cross-linked by ultraviolet (UV) curing combined with traditional polyvinylidene difluoride binder (i.e., forming a binary binder, denoted as c-ETPTA/PVDF) to construct high-loading and durable Li-S batteries. The covalently cross-linked ETPTA framework not only significantly enhances …

Preface To The Special Issue On Lithium-Sulfur Batteries, Jia-Jia Chen, Ren-Jie Chen, Zhong Jin

Journal of Electrochemistry

No abstract provided.

Coni-Based Bimetal-Organic Framework Derived Carbon Composites Multifunctionally Modified Separators For Lithium-Sulfur Batteries, Yan-Jie Wang, Hong-Yu Cheng, Ji-Yue Hou, Wen-Hao Yang, Rong-Wei Huang, Zhi-Cong Ni, Zi-Yi Zhu, Ying Wang, Ke-Yi Wei, Yi-Yong Zhang, Xue Li

Journal of Electrochemistry

The commercial application of lithium-sulfur batteries (LSB) is still limited by the irreversible capacity fading caused by the shuttle of lithium polysulfides (LIPS). To address this issue, a bimetal (nickel, cobalt)-organic framework (MOF) derived carbon, (Ni, Co)/C, was prepared to modify the separator. The multifunctionally modified separator effectively captures LIPS, ensuring the stability and reversibility of sulfur fixation, while providing catalytic activity and improving ionic conductivity. The cobalt metal has a larger coordination number, more pore structure distribution, larger specific surface area, more surface C=O, and smaller particle size to achieve a large and rapid chemical sulfur fixation. The high …

Preface To The Special Issue On Lithium-Sulfur Batteries, Jia-Jia Chen, Ren-Jie Chen, Zhong Jin

Journal of Electrochemistry

No abstract provided.

Recent Research Progresses Of Solid-State Lithium-Sulfur Batteries, Yu Luo, Ru-Qin Ma, Zheng-Liang Gong, Yong Yang

Journal of Electrochemistry

All solid-state lithium-sulfur batteries (ASSLSBs) are considered to be one of the most promising next-generation energy storage systems, due to the promises of high energy density and safety. Although the use of solid-state electrolytes could effectively suppress the "shuttle effect" and self-discharge of the conventional liquid lithium-sulfur (Li-S) battery, the commercialization of ASSLSBs has been seriously hampered by the electrolyte degradation, electrode/electrolyte interfacial deterioration, electrochemo-mechanical failure, lithium dendrite growth and electrode pulverization, etc. This paper provides a comprehensive review of recent research progresses on the solid-state electrolytes, sulfur-containing composite cathodes, lithium metal and lithium alloy anodes, and electrode/electrolyte interfaces in …

A Review On Solid-State Li-S Battery: From The Conversion Mechanism Of Sulfur To Engineering Design, Huan-Huan Jia, Chen-Ji Hu, Yi-Xiao Zhang, Li-Wei Chen

Journal of Electrochemistry

Lithium-sulfur (Li-S) batteries attract sustained attention because of their ultrahigh theoretical energy density of 2567 Wh·kg^–1 and the actual value over 600 Wh·kg^–1. Solid-state Li-S batteries (SSLSBs) emerge in the recent two decades because of the enhanced safety when compared to the liquid system. As for the SSLSBs, except for the difference in the conversion mechanism induced by the cathode materials themselves, the physical-chemical property of solid electrolytes (SEs) also significantly affects their electrochemical behaviors. On account of various reported Li-S batteries, the advantages and disadvantages in performance and the failure mechanism are discussed in this review. …

Bimetallic Compound Catalysts With Multiple Active Centers For Accelerated Polysulfide Conversion In Li-S Batteries, Wu-Xing Hua, Jing-Yi Xia, Zhong-Hao Hu, Huan Li, Wei Lv, Quan-Hong Yang

Journal of Electrochemistry

Practical applications of lithium-sulfur (Li-S) batteries are hindered mainly by the low sulfur utilization and severe capacity fading derived from the polysulfide shuttling. Catalysis is an effective remedy to those problems by promoting the conversion of polysulfides to reduce their accumulation in the electrolyte, which needs the catalyst to have efficient adsorption ability to soluble polysulfides and high activity for their conversion. In this work, we have proposed a bimetallic compound of NiCo₂S₄ anchored onto sulfur-doped graphene (NCS@SG) to fabricate a catalytic interlayer for Li-S batteries. Compared to CoS, the NiCo₂S₄ demonstrated much higher …