Materials Science and Engineering Commons^™

Numerical Calculation Of Losses Of Trapped Vortices Under Strong Rf Meissner Current And Dc Superheating Field In Type Ii Superconductors, Walive Pathiranage Manula Randhika Pathirana

Physics Theses & Dissertations

Research on the vortex dynamics and enhancing of superheating field in superconductors has attracted much attention in accelerator physics community to develop next-generation high-performance accelerator cavities. However, the extreme dynamics of curvilinear elastic vortices driven by very strong currents close to the depairing limit or superheating field of a superconductor with a nanostructured surface has not been well understood. We calculated the superheating field H_sh and critical momentum kc characterizing the wavelength of the instability λ_m of the Meissner state to flux penetration by solving numerically the Ginzburg-Landau equations. A bulk superconductor, superconductor with the inhomogeneous surface disorder …

Quantum Transport Of The 2d Surface State In A Nonsymmorphic Semimetal, Xue Liu, Jin Hu, Jiang Wei, Chunlei Yue, Sergey V. Erohin, Yanglin Zhu, Abin Joshy, Jinyu Liu, Ana M. Sanchez, David Graf, Pavel B. Sorokin, Zinqiang Mao

Physics Faculty Publications and Presentations

In a topological semimetal with Dirac or Weyl points, the bulk-boundary correspondence principle predicts a gapless edge mode if the essential symmetry is still preserved at the surface. The detection of such topological surface state has been considered as the fingerprint prove for crystals with nontrivial topological bulk band. On the contrary, it has been proposed that even with symmetry broken at the surface, a new surface band can emerge in nonsymmorphic topological semimetals. The symmetry reduction at the surface lifts the bulk band degeneracies and produces an unusual “floating” surface band with trivial topology. Here, we first report quantum …

First-Principles Density Functional Theory Studies On Perovskite Materials, Aneer Lamichhane

Dissertations

Perovskites are a family of materials with a diverse combination of different elements. As a consequence, they exhibit numerous functionalities such as pyroelectric, piezoelectric, ferroelectric, and ferromagnetic with applications in photovoltaic cells, LEDs, superconductivity, colossal magneto-resistance, and topological insulators. After 2009, perovskites have gained notoriety as suitable materials for solar cells and alternative candidates to silicon-based conventional solar cells. Generally, oxide perovskites exhibit good dielectric properties, halide perovskites display good photonic qualities, and chalcogenide perovskites are used in applications in solid-state lighting, sensing, and energy harvesting. In this dissertation, various types of perovskites ranging from oxide to halide are investigated …

Assessment Of Natural Radioactivity And Radiation Hazards Of Building Materials In Kinondoni District, Dar Es Salaam, Tanzania, Huruma P Mammba, Vitus A Balobegwa, Alex P Muhulo, Peter A Pantaleo, Remigius A Kawala

Tanzania Journal of Science

Natural radionuclides from building materials are one of the potential sources of external as well as internal radiation exposure to the human body. Currently, this exposure has been increasing since people spend more than  of their time indoors (ICRP 1991). Commonly used building materials from Kinondoni District were investigated using γ-spectrometry; their activity concentrations of 226Ra, 232Th and 40K in Bq/kg were measured. The results showed that average values of activity concentrations of 226Ra, 232Th and 40K were 15.62, 21.51 and 237.99 Bq/kg, respectively. All the activity concentrations in the studied samples were lower than the world average values of …

Multi-Scale Computational Modeling Of Metal/Ceramic Interfaces, Abu Shama Mohammad Miraz

Master's Theses

Multi-scale atomistic calculations were carried out to understand the interfacial features that dictate the mechanical integrity of the metal/ceramic nanolaminates. As such, first principles density functional theory (DFT) calculations were performed to understand the electronic and atomistic factors governing adhesion and resistance to shear for simple metal/ceramic interfaces, whereas molecular dynamics (MD) simulations were performed to observe the impact of interfacial structures, such as misfit dislocation network geometries and orientation relationships, on interfacial mechanical properties.

For the DFT investigation, we choose metals with different crystal structures, namely - Cu (fcc), Cr (bcc) and Ti (hcp) along with a variety of …

Voltage-Controlled Magnetic Anisotropy In Antiferromagnetic Mgo-Capped Mnpt Films, P. H. Chang, Wuzhang Fang, T. Ozaki, Kirill Belashchenko

Kirill Belashchenko Publications

The magnetic anisotropy in MgO-capped MnPt films and its voltage control are studied using first-principles calculations. Sharp variation of the magnetic anisotropy with film thickness, especially in the Pt-terminated film, suggests that it may be widely tuned by adjusting the film thickness. In thick films the linear voltage control coefficient is as large as 1.5 and -0.6 pJ/Vm for Pt-terminated and Mn-terminated interfaces, respectively. The combination of a widely tunable magnetic anisotropy energy and a large voltage-control coefficient suggest that MgO-capped MnPt films can serve as a versatile platform for magnetic memory and antiferromagnonic applications.

Multi-Scale Computational Modeling Of Metal/Ceramic Interfaces, Abu Shama Mohammad Miraz

Doctoral Dissertations

Multi-scale atomistic calculations were carried out to understand the interfacial features that dictate the mechanical integrity of the metal/ceramic nanolaminates. As such, first principles density functional theory (DFT) calculations were performed to understand the electronic and atomistic factors governing adhesion and resistance to shear for simple metal/ceramic interfaces, whereas molecular dynamics (MD) simulations were performed to observe the impact of interfacial structures, such as misfit dislocation network geometries and orientation relationships, on interfacial mechanical properties.

For the DFT investigation, we choose metals with different crystal structures, namely - Cu (fcc), Cr (bcc) and Ti (hcp) along with a variety of …

Mechanical Behavior Of Cyclo-18 On Nickel And Copper Substrates, Reagan Michael Kraft

Mechanical Engineering Undergraduate Honors Theses

Carbyne, an -hybridized allotrope of carbon, has been the subject of many studies recently due to its incredible mechanical properties and small size. More recently, another -hybridized allotrope known as cyclo-18, has gained interest. In this study, computational molecular dynamics will be used to determine the mechanical properties of cyclo-18. Peeling and shearing tests of the molecule will be conducted on nickel and copper, which are respectively active and less-active transition metals. Additionally, a carbyne chain of equal length will undergo the same tests on the copper substrate to compare the mechanical properties of the two. The results conclude that …

Design And Control Of A Peristaltic Pump To Simulate Left Atrial Pressure In A Conductive Silicone Model, Jeremy Collins

Mechanical Engineering Undergraduate Honors Theses

According to the CDC, atrial fibrillation is responsible for more than 454,000 hospitalizations and approximately 158,000 deaths per year. A common treatment for atrial fibrillation is catheter ablation, a process in which a long flexible tube is guided through the femoral artery and to the source of arrhythmia in the heart, where it measures the electrical potential at various locations and converts problematic heart tissue to scar tissue via ablation. This paper details the design and control of a low-cost ($400) peristaltic pump system using repetitive control to replicate blood pressure in the left atrium in a conductive silicone model …

Photothermal Response Induced By Nanocage-Coated Artificial Extracellular Matrix Promotes Neural Stem Cell Differentiation, Seunghyun Jung, Nathaniel Harris, Isabelle I. Niyonshuti, Samir V. Jenkins, Abdallah M. Hayar, Fumiya Watanabe, Azemat Jamshidi-Parsian, Jingyi Chen, Michael J. Borrelli, Robert J. Griffin

Mechanical Engineering Faculty Publications and Presentations

Strategies to increase the proportion of neural stem cells that differentiate into neurons are vital for therapy of neurodegenerative disorders. In vitro, the extracellular matrix composition and topography have been found to be important factors in stem cell differentiation. We have developed a novel artificial extracellular matrix (aECM) formed by attaching gold nanocages (AuNCs) to glass coverslips. After culturing rat neural stem cells (rNSCs) on these gold nanocage-coated surfaces (AuNC-aECMs), we observed that 44.6% of rNSCs differentiated into neurons compared to only 27.9% for cells grown on laminin-coated glass coverslips. We applied laser irradiation to the AuNC-aECMs to introduce precise …

Study Of Static And Dynamical Properties Of Complex Antiferroelectrics Materials, Kinnary Yogeshbhai Patel

Graduate Theses and Dissertations

The aim of this dissertation is the investigation of the static and dynamical properties of the complex antiferroelectric materials using Effective Hamiltonian method and First principles calculations. In chapter 3, a novel elemental interatomic coupling in perovskite materials which bilinearly couples the antiferroelectric displacements of cations with the rotations of the oxygen octahedra. This new coupling explains a very complex crystal structure of prototypical antiferroelectric PbZrO3. My explanation provides a unified description of many other complex antipolar crystal structures in variety of perovskite materials, including the occurrence of incommensurate phases in some of them. In chapter 4, results and analysis …

Simulation Of Optical Properties Of Dielectric Layers From Visible To Near Infrared Spectral Range, Andrew Cochran, Cory Conkel

ONU Student Research Colloquium

Optical properties of dielectrics play a critical role in various applications including the design and manufacture of optical components & devices such as detectors, filters, imagers, lenses, optical coatings, photonic crystals, sensors and waveguides, and solar cells. Radiative properties of varying thicknesses of different dielectrics such as Aluminum Oxide (Al2O3), Silicon Dioxide (SiO2), Indium Tin Oxide (ITO), Magnesium Fluoride (MgF2) and Silicon Nitride (Si3N4) have been simulated and compared in the range of visible to near infrared by mathematical modelling using MATLAB simulations. The results of the evolution of the radiative properties, as a function of dielectric material thickness, on …

Securing Pint Glasses On Serving Trays With Magnetic Attachments, Jayden Commendatore

Senior Theses

It is extremely common for servers in the restaurant industry to have pint glasses slip off their serving tray, wasting both time and money for the restaurant. I have designed a sleeve attachment that will clip on to the bottom of a pint glass. The metal sleeve attachment will be attracted to a magnet placed into the serving tray. This increases the normal force of the pint glass, resulting in an increase in the friction force between the tray and sleeve attachment, and helping secure the glass to the tray. In order to optimize the design, the value of the …

Relationship Between Thermal Conductivity And Free Electrons In Metal, Yansong Liu

Senior Theses

An experiment was designed and conducted to explore the relationship between thermal conductivity with free electrons in metal. In the experiment, copper, iron, aluminum, and titanium rods with close diameters were used to carry out the experiment. Each rod was heated up by a heat unit at one end while cooled on the other end with a heat sink to maintain a steady state. DC current was applied to rods in the direction along, as well as against, the heat flow. Thermal conductivities were measured in these two situations for each rod. Results showed electrons do dominate thermal flow inside …

Origin Of Magnetism In Γ-Fesi 2 /Si(111) Nanostructures, Liwei D. Geng, Sahil Dhoka, Ilan Goldfarb, Ranjit Pati, Yongmei M. Jin

Michigan Tech Publications, Part 1

Magnetism has recently been observed in nominally nonmagnetic iron disilicide in the form of epitaxial γ-FeSi2 nanostructures on Si(111) substrate. To explore the origin of the magnetism in γ-FeSi2/Si(111) nanostructures, we performed a systematic first-principles study based on density functional theory. Several possible factors, such as epitaxial strain, free surface, interface, and edge, were examined. The calculations show that among these factors, only the edge can lead to the magnetism in γ-FeSi2/Si(111) nanostructures. It is shown that magnetism exhibits a strong dependency on the local atomic structure of the edge. Furthermore, magnetism can be enhanced by creating multiple-step edges. In …

Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A passive microscopic Fabry-Pérot Interferometer (FPI) sensor an optical fiber a three-dimensional microscopic optical structure formed on a cleaved tip of an optical fighter that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

High Quality Single-Crystalline Aluminum Nitride Grown Using Pulsed Atomic-Layer Epitaxy Technique By Mocvd On Sapphire Substrate, Mohd Nazri Abd Rahman

Student Works (2020-2029)

The unique structural properties and engineering characteristics of nitride-based materials have given them a special position in semiconductor applications. Alloys with a tuned energy bandgap from ultraviolet to infrared wavelengths are possible to be deposited in maintaining the wurtzite crystal structure. However, the aluminum nitride / aluminum gallium nitride (AlN/AlGaN) based hetero-structures for deep-ultraviolet (DUV) emitters as well as AlN-based actuators and piezoelectric sensors are highly inefficient owing to the excessive mismatch in thermal and lattice features between these epilayers with flat c-plane sapphire substrates, resulting in crack formation and high dislocation densities. This thesis mainly focuses on the development …

Doped-Magnesium Manganese Oxide Cathode For Rechargeable Magnesium Batteries, Nurhidayu Harudin

Student Works (2020-2029)

Magnesium has numerous good characteristics that make it attractive as an electrode material for rechargeable batteries. There are many advantages of Magnesium (Mg) such as available in abundance, ease of handling, low toxicity and environmental friendly. Due to its benefits, magnesium ion battery can be considered as an alternative to lithium in future. In the present work, the improvement electrochemical properties of magnesium-based cathode material, MgMn2O4 was done by adding calcium (Ca) and strontium (Sr) as dopant i.e MgMn2-xCaxO4 and MgMn2-xSrxO4. These materials with compositions of x=0.1,0.2,0.3,0.4,0.5 were synthesized by self-propagating combustion method using citric acid as a reducing agent. …

Study Of Schottky And Poole-Frenkel Conduction Mechanism In Fe304-Gamma-Fe2o3/Sio2/N-Type Si System, Adrian Chung Ning Hann

Student Works (2020-2029)

The advances of metal oxide semiconductor technology (MOS) have led to smaller devices being made where sizes of the devices keep getting smaller and compact. Hence, all the components of metal oxide semiconductor sizes are to be reduced without affecting the overall efficiency of the metal oxide semiconductor. However, there is a problem in the silicon dioxide component of MOS as the sizes of the silicon oxide (SiO2) reduces, there is a possibility a current leakage to occur due to carrier direct tunneling effect passing through SiO2 which reduce the efficiency of the MOS. Therefore, a higher dielectric constant material …

Photoinduced Trapping Of Charge At Sulfur Vacancies And Copper Ions In Photorefractive Sn2P2S6 Crystals, Timothy D. Gustafson, Eric M. Golden, Elizabeth M. Scherrer, Nancy C. Giles, A. A. Grabar, Sergey A. Basun, Jonathan E. Slagle [*], Larry E. Halliburton

Faculty Publications

Electron paramagnetic resonance (EPR) is used to monitor photoinduced changes in the charge states of sulfur vacancies and Cu ions in tin hypothiodiphosphate. A Sn₂P₂S₆ crystal containing Cu+ (3d10) ions at Sn²⁺ sites was grown by the chemical vapor transport method. Doubly ionized sulfur vacancies (V²⁺S) are also present in the as-grown crystal (where they serve as charge compensators for the Cu+ ions). For temperatures below 70 K, exposure to 532 or 633 nm laser light produces stable Cu²⁺ (3d⁹) ions, as electrons move from Cu⁺ ions to …

Nanoengineered Materials For Energy Conversion & Storage Applications: A Density Functional Theory Study, Ahmed Biby

Theses and Dissertations

The conventional approach for the development of novel materials has become long relative to the desired product development cycle. Thus, the sluggish pace of the development of materials within the conventional approach hinders the rapid transformation of the scientific outcomes into useful technological products. To this end, the field of hierarchical materials informatics evolved to bridge this gap. In this field, the multiscale material internal structure is considered the starting point and the core of this approach. This being said, the density functional theory (DFT) was used to generate useful materials data for the advancement of the hierarchical materials data-bases …

Synthesis And Characterization Of Perovskite-Based Materials For Memory Device Application, Gregory Thien Soon How

Student Works (2020-2029)

This project aims to study the resistive switching behaviour in memory devices using perovskites-based structures. A hybrid organic-inorganic lead halide perovskite was studied in this project, specifically methylammonium lead triiodide, CH3NH3PbI3 or MAPbI3 perovskite. The effect of the various counter electrodes in MAPbI3 perovskite was investigated by fabricating MAPbI3 perovskite on Indium Tin Oxide (ITO). Three commonly used electrodes which are Aluminium (Al), Silver (Ag), and Gold (Au) were thermally evaporated on top of the MAPbI3 perovskite layer. It was found that the ITO/MAPbI3/Al exhibits Resistive Random Access Memory (ReRAM) behaviour with SET voltage (VSET) of 4.5 V and RESET …

Surface Acoustic Waves Increase Magnetic Domain Wall Velocity, Anil Adhikari, Shireen Adenwalla

Shireen Adenwalla Papers

Domain walls in magnetic thin films are being explored for memory applications and the speed at which they move has acquired increasing importance. Magnetic fields and currents have been shown to drive domain walls with speeds exceeding 500 m/s. We investigate another approach to increase domain wall velocities, using high frequency surface acoustic waves to create standing strain waves in a 3 micron wide strip of magnetic film with perpendicular anisotropy. Our measurements, at a resonant frequency of 248.8 MHz, indicate that domain wall velocities increase substantially, even at relatively low applied voltages. Our findings suggest that the strain wave …

Aps March Meeting 2021 (Online) Updates On Scientific Research During Pandemic Times, Vianney Gimenez-Pinto

Title III Professional Development Reports

While the ongoing global pandemic continues to affect our everyday lives, researchers in Science, Technology, Engineering and Math found a way to come together at the American Physical Society (APS) March Meeting 2021. The conference was online-only and had more than 11,000 registered attendants who actively participated in the program during March 14- 19, 2021.

Observation Of New Particle Formation In The Northern Hemisphere At Altitude From 4 To 20 Km, Mohamed Saad

Electronic Theses and Dissertations

New particle formation (NPF) is investigated using measurements of aerosol size distributions and meteorological variables made in two continents, including USA and Europe. Despite the considerably different aerosol particle abundances among the sites, a common relationship was found between the characteristics of NPF events and the air mass convective and/or advective transport. CO and O3 act as tracers of tropospheric and stratospheric air, respectively, their statistical relationship can be used to quantify air mass characteristics and origins. The mixing ratio values of CO increased within the upper troposphere layer before/during NPF events, which may serve as an indicator of occurring …

Experimental Exploration Of Shared Magnetic Phases Between Diverse Systems Of Iron-Pnictide Superconductors, Ryan Scott Stadel

Graduate Research Theses & Dissertations

The exciting field of iron-pnictide superconductors offers unique opportunities for studying the relationship between magnetism and unconventional superconductivity. This is vital to developing an understanding of the microscopic origin of high-temperature superconductivity, which is itself an important step in harnessing such a potentially revolutionary technology.

Polycrystalline and crystalline samples are synthesized over a diverse collection of related iron-pnictide systems including (Ca,Sr,Ba)1-xNaxFe2As2, Ba(Fe1-xCox)2As2 (122s), and LaFeAs1-xPxO, and TbFeAs1-xPxO (1111s). These compounds are characterized through various types of neutron and x-ray diffraction on multiple instruments, as well as muon spin resonance, and magnetic susceptibility measurements.

A thorough investigation into the conditions under …

Effect Of Random Pinning On Nonlinear Dynamics And Dissipation Of A Vortex Driven By A Strong Microwave Current, W.P.M.R. Pathirana, Alex Gurevich

Physics Faculty Publications

We report numerical simulations of a trapped elastic vortex driven by a strong ac magnetic field H(t)=Hsinωt parallel to the surface of a superconducting film. The surface resistance and the power dissipated by an oscillating vortex perpendicular to the film surface were calculated as functions of H and ω for different spatial distributions, densities, and strengths of pinning centers, including bulk pinning, surface pinning, and cluster pinning. Our simulations were performed for both the Bardeen-Stephen viscous vortex drag and the Larkin-Ovchinnikov (LO) drag coefficient η(v) decreasing with the vortex velocity v. The local residual surface resistance R_i(H) …

Establishing Independent Tunability Of The Mechanical And Transport Properties Of Polymer Gels, Lucas Rankin

Master’s Theses

Polymer gels can be used in the fabrication of materials for filtering liquid and gaseous media, solid-state electrolytes, and transdermal medical patches. This diverse range of applications primarily relies on the transport and mechanical properties of polymer gels. Both sets of properties have shown excellent tunability, but typically in a coupled fashion. Establishing the independent tunability of the transport and mechanical properties of polymer gels (using simple, cost-effective methods) is paramount if polymer gels are to be used to their full potential. Specifically, block copolymer gels self-assemble into organized nanoscale networks within the gel solvent, which allows for facile control …

Development Of Synthetic Coal Char Simulant For Microwave Conversion Studies: A Computationally-Driven Approach, Kevin A. Hager

Graduate Theses, Dissertations, and Problem Reports (ETD)

Recent experimental demonstration of new reaction windows for coal char/methane reactions that are less energy-intensive, provides innovation for modular reactors. However, the correlation of the exact mechanism for the enhancement of these reaction windows is not certain. This study investigates the simplification of these experimental studies by developing a well-characterized coal char simulant. The approach involves using a computational approach to screen macroscopic composition to replicate the dielectric and compositional response of actual char. This study is focused on PRB coal char. A discrete element method (DEM) technique was used to simulate the packing of coal chars to give the …

Equations Of State For Warm Dense Carbon From Quantum Espresso, Derek J. Schauss

Theses and Dissertations

Warm dense plasma is the matter that exists, roughly, in the range of 10,000 to 10,000,000 Kelvin and has solid-like densities, typically between 0.1 and 10 grams per centimeter. Warm dense fluids like hydrogen, helium, and carbon are believed to make up the interiors of many planets, white dwarfs, and other stars in our universe. The existence of warm dense matter (WDM) on Earth, however, is very rare, as it can only be created with high-energy sources like a nuclear explosion. In such an event, theoretical and computational models that accurately predict the response of certain materials are thus very …