Materials Science and Engineering Commons^™

Development Of High Conductivity Copper Coatings For Srf Cavity, Himal Pokhrel

Physics Theses & Dissertations

The development of metallic coatings with high purity and high thermal conductivity at cryogenic temperature could be very important for application to the superconducting radiofrequency (SRF) cavity technology. The deposition of such bulk coatings on the outer surface of a niobium cavity could result in higher heat conductance and mechanical stiffness, both of which are crucial for enhancing the cavity performance at a reduced cost.

Cold spray technology was used to deposit bulk coatings of pure copper and copper-tungsten alloys on the niobium substrate and the samples of size 2 mm × 2 mm cross section were cut and subjected …

Design, Fabrication, And Characterization Of An Array Of Graphene Based Variable Capacitors, Millicent Nkirote Gikunda

Graduate Theses and Dissertations

Since it was first isolated and characterized in 2004, graphene has shown the potential for a technological revolution. This is due to its amazing physical properties such as high electrical conductivity, high thermal conductivity, and extreme flexibility. Freestanding graphene membranes naturally possesses an intrinsic rippled structure, and these ripples are in constant random motion even room temperatures. Occasionally, the ripples undergo spontaneous buckling (change of curvature from concave to convex and vice versa) and the potential energy associated with this is a double well potential. This movement of graphene is a potential source of vibrational energy.

In this dissertation, we …

Controlling Unequal Surface Energy Results Caused By Test Liquids: The Case Of Uv/O3 Treated Pet, Bilge N. Altay, Paul D. Fleming, Md Arifur Rahman, Alexandra Pekarovicova, Bruce Myers, Cem Aydemir, Arif Karademir

Articles

Ultraviolet/ozone (UV/O3) treatment has been reported to be an effective method to modify properties such as wettability, adhesion or adsorption of plastic surfaces. The change in the surface is measured by contact angle analysis, which employs liquids and their surface tensions (ST) to estimate the surface energy (SE). We found two different practices in the scientific community: (1) the majority of researchers adopted the ST value of liquids from the literature, while (2) other researchers conducted real-time measurements in the lab under ambient conditions prior to SE estimation. To the best of our knowledge, there is no study that compares …

Lattice Dynamics, Mechanical Properties, Electronic Structure And Magnetic Properties Of Equiatomic Quaternary Heusler Alloys Crticoz (Z = Al, Si) Using First Principles Calculations, Eesha Andharia, Hind Alqurashi, Bothina Hamad

Physics Faculty Publications and Presentations

First principles calculations are performed to investigate the thermodynamical stability, dynamical, mechanical, electronic and magnetic properties of CrTiCoZ (Z = Al/Si) novel quaternary Heusler alloys. A Y-type III atomic configuration is found to be the most stable structure for both compounds. The lattice constant values obtained using GGA-PBE approach are 5.9368 Å and 5.7853 Å for CrTiCoAl and CrTiCoSi, respectively. Using the value of elastic moduli for both the compounds, the computed Pugh’s ratio value is 2.5 and 2.7 for CrTiCoAl and CrTiCoSi, respectively, which is higher than 1.75, indicating both the compounds are ductile in nature. The melting temperatures …

Limits Of Detection Of Mycotoxins By Laminar Flow Strips: A Review, Xinyi Zhao, Hugh Byrne, Christine M. O’Connor, James Curtin, Furong Tian

Articles

Mycotoxins are secondary metabolic products of fungi. They are poisonous, carcinogenic, and mutagenic in nature and pose a serious health threat to both humans and animals, causing severe illnesses and even death. Rapid, simple and low-cost methods of detection of mycotoxins are of immense importance and in great demand in the food and beverage industry, as well as in agriculture and environmental monitoring, and, for this purpose, lateral flow immunochromatographic strips (ICSTs) have been widely used in food safety and environmental monitoring. The literature to date describing the development of ICSTs for the detection of different types of mycotoxins using …

Soft Magnetic Composite Substrates For Rf/Microwave Applications, Poonam Lathiya

USF Tampa Graduate Theses and Dissertations

Novel soft magnetic ferrite materials will play a crucial role in next-generation over one trillion sensors (also known as “trillion sensor economy) related to 5G communications and internet of things, as these materials can achieve improved wireless power and signal transfer efficiency with high operation frequency. In this work, Ni-Cu-Zn and Ni-Co-Zn ferrites with high permeability, high permittivity, and low magnetic and dielectric losses were prepared for RF and microwave device applications. Frequency dispersion of RF complex permeability of Ni-Cu-Zn ferrites prepared under different applied hydraulic pressures and durations have been thoroughly investigated. The Ni0.35Cu0.19Zn0.46Fe2O4 ferrites were prepared by conventional …

Effects Of Annealing Ambient On The Structural, Optical And Electrical Properties Of Tio2:Ge Thin Films, Lilian A. Owino, Sebastian Waita, Robinson J. Musembi, Francis W Nyongesa

Tanzania Journal of Science

TiO2, a semiconducting material with a wide energy band gap, has been researched intensively due to its interesting properties and many potential applications. The films properties can as well be modified by preparing the films under diverse ambient to suit diverse applications. In this work, the effects of the annealing atmosphere on the structural, optical and electrical properties of pure TiO2 and TiO2:Ge composite thin films deposited by sputtering from commercially available pure TiO2 and TiO2:Ge (85:15) targets respectively were studied. The films were deposited on fluorine doped tin oxide glass substrates by radio frequency magnetron sputtering technique at room …

Method Of Making Hinged Self-Referencing Fabry–Pérot Cavity Sensors, Jeremiah C. Williams, Hengky Chandrahalim

AFIT Patents

A method is provided for fabricating a passive optical sensor on a tip of an optical fiber. The method includes perpendicularly cleaving a tip of an optical fiber and mounting the tip of the optical fiber in a specimen holder of a photosensitive polymer three-dimensional micromachining machine. The method includes forming a three-dimensional microscopic optical structure within the photosensitive polymer that comprises a two cavity Fabry-Perot Interferometer (FPI) having a hinged optical layer that is pivotally coupled to a suspended structure. The method includes removing an uncured portion of the photosensitive polymer using a solvent. The method includes depositing a …

Computational Study Of The Reactions Of Heteroatomic Compounds On Ceo2, Suman Bhasker Ranganath

LSU Doctoral Dissertations

The mechanisms of ambient-temperature reactions of heteroatomic compounds catalyzed by ceria (CeO₂), an archetypical reducible oxide, for enzyme mimetics, environmental protection, and chemical synthesis are investigated in this dissertation using theoretical methods. CeO₂ is modeled with thermodynamically stable low-index surfaces exposed by commonly studied ceria thin films and nano particles. To understand phosphatase-like dephosphorylation activity, stable adsorption states and surface reactions of model phosphates are examined. Binding of the central P-atom to surface lattice oxygen (O_latt) supplemented by phosphoryl O-Ce interaction is the only stable adsorption state for the un-dissociated molecule. Deprotonation of phosphate monoesters, …

Formulation And Characterization Of Fast-Curing Plastic Scintillators With High-Z Loading, Theodore W. Stephens

Theses and Dissertations

Development of novel fast-curing plastic scintillators is highly advantageous due to their potential to be manufactured via 3D printing. Several formulations were developed that exhibit enhanced photon sensitivity, producing modest but discernible photopeaks at an incident gamma energy of 122 keV. The photon sensitivity is achieved via bismuth high-Z loading; however, this practice typically results in diminished light yields. Subsequent formulations, which varied the photoinitiator concentration and curing time, demonstrated successful curing with sufficient plastic hardness, reduced purple discoloration, reduced heat buildup during curing, and resulted in less cracking during the curing process, all of which were correlated with lower …

Effects Of Vacancies And Electron Temperature On The Electron Phonon Coupling In Cubic Silicon Carbide And Their Connection To The Inelastic Thermal Spike, Salah Al-Smairat

Doctoral Dissertations

“The electron-phonon interaction is an important interaction in many solids as it influences transport phenomena and related quantities such as the electrical and thermal conductivities, especially in nuclear and space applications. The importance of the electron-phonon interaction in primary damage production in 3C-SiC is the subject of this research.

The electron-phonon coupling factor was calculated using a hybrid Density Functional Perturbation Theory - Classical Electron Gas model. The coupling factor was calculated as a function of electron temperature in pristine and defective 3C-SiC, and relaxed defective cells. The electron-phonon coupling is found to depend strongly on the electronic temperature and …

Magnetic Field Penetration Technique To Study Field Shielding Of Multilayered Superconductors, Iresha Harshani Senevirathne, Alex Gurevich, Jean R. Delayen, A-M Valente-Feliciano

Physics Faculty Publications

The SIS structure which consists of alternative thin layers of superconductors and insulators on a bulk niobium has been proposed to shield niobium cavity surface from high magnetic field and hence increase the accelerating gradient. The study of the behavior of multilayer superconductors in an external magnetic field is essential to optimize their SRF performance. In this work we report the development of a simple and efficient technique to measure penetration of magnetic field into bulk, thin film and multilayer superconductors. Experimental setup contains a small superconducting solenoid which can produce a parallel surface magnetic field up to 0.5 T …

Modeling, Fabrication, And Characterization Of Rf-Based Passive Wireless Sensors Composed Of Refractory Semiconducting Ceramics For High Temperature Applications, Kavin Sivaneri Varadharajan Idhaiam

Graduate Theses, Dissertations, and Problem Reports (ETD)

Real-time health monitoring of high temperature systems (>500^oC) in harsh environments is necessary to prevent catastrophic events caused by structural failures, varying pressure, and chemical reactions. Conventional solid-state temperature sensors such as resistance temperature detectors (RTDs) and thermocouples are restricted by their operating environments, sensor dimensions and often require external power sources for their operation. The current work presents the research and development of RF-based passive wireless sensing technology targeting high temperatures and harsh environmental conditions. Passive wireless devices are generally classified as near-field and far-field devices based on the interrogation distance. Near-field sensors are placed at …

Experimental And Computational Studies Of Functionalized Carbon Nanotubes For Use In Energy Storage Devices And Membranes, Emine S. Karaman

Dissertations

Electrolytes with good interfacial stability are a crucial component of any electrochemical device. The development of novel gel polymer electrolytes (GEs) with good interface stability and better manufacturability is important for the development of the next generation electrochemical devices. Gel electrolytes are hybrid electrolyte materials, combining benefits of both liquid and solid systems. Compared with liquid and solid electrolytes, GEs open new design opportunities and do not require rigorous encapsulation methods. In this dissertation, studies on functionalized carbon nanotubes (fCNTs) and graphene oxide (GO) doped polyvinyl alcohol (PVA) based gel electrolytes (GEs) are reported. The ionic conductivity and mechanical strength …

Electric-Field-Driven Processes In Multiphase Fluid Systems, Qian Lei

Dissertations

Advantages of using electric fields in miniaturized apparatuses for a wide range of applications are revealed by numerous experimental and theoretical studies over the last several decades as it offers a simple and efficient method for manipulation of multiphase fluid systems. This approach is considered to be especially beneficial for control of boiling processes and colloidal suspensions considered in the presented work.

Boiling. Today's trends for enhancing boiling heat transfer in terrestrial and space applications focus on removal of bubbles to prevent formation of a vapor layer over the surface at a high overheat. In contrast, this dissertation presents a …

Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A passive microscopic Fabry-Pérot Interferometer (FPI) sensor an optical fiber a three-dimensional microscopic optical structure formed on a cleaved tip of an optical fighter that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

Reliability Characterization Of A Low-K Dielectric Using Its Magnetoresistance As A Diagnostic Tool, Philip Alister Williams

Legacy Theses & Dissertations (2009 - 2024)

The introduction of low dielectric constant materials within the integrated circuit (IC) chip technology industry was a concerted effort to decrease the resistance-capacitance (RC) time delay inherent within the dielectric materials used as insulators. This stems from a demand for greater device density per IC chip and decreased feature sizes but is fast becoming a reliability issue. Concomitant with the demand for decreased feature sizes, also in adherence with Moore’s Law (which states that the number of devices on a die doubles every two years), is a reduction in device speed and performance due to device intra-level interconnection signal delays. …

Investigation Of Optical And Structural Properties Of Gesn Heterostructures, Oluwatobi Gabriel Olorunsola

Graduate Theses and Dissertations

Silicon (Si)-based optoelectronics have gained traction due to its primed versatility at developing light-based technologies. Si, however, features indirect bandgap characteristics and suffers relegated optical properties compared to its III-V counterparts. III-Vs have also been hybridized to Si platforms but the resulting technologies are expensive and incompatible with standard complementary-metal-oxide-semiconductor processes. Germanium (Ge), on the other hand, have been engineered to behave like direct bandgap material through tensile strain interventions but are well short of attaining extensive wavelength coverage. To create a competitive material that evades these challenges, transitional amounts of Sn can be incorporated into Ge matrix to form …

Dreams Of Molecular Beams: Indium Gallium Arsenide Tensile-Strained Quantum Dots And Advances Towards Dynamic Quantum Dots (Moleculare Radiorum Somnia: Indii Gallii Arsenicus Tensa Quanta Puncta Et Ad Dinamicae Quantae Puntae Progressus), Kevin Daniel Vallejo

Boise State University Theses and Dissertations

Through the operation of a molecular beam epitaxy (MBE) machine, I worked on developing the homoepitaxy of high quality InAs with a (111)A crystallographic orientation. By tuning substrate temperature, we obtained a transition from a 2D island growth mode to step- ow growth. Optimized MBE parameters (substrate temperature = 500 °C, growth rate = 0.12 ML/s and V/III ratio ⩾ 40) lead to growth of extremely smooth InAs(111)A films, free from hillocks and other 3D surface imperfections. We see a correlation between InAs surface smoothness and optical quality, as measured by photoluminescence spectroscopy. This work establishes InAs(111)A as a platform …

Hybrid Two Dimensional Quantum Devices, Joshua Patrick Thompson

Graduate Theses and Dissertations

This thesis describes measurements on hybrid material systems involving two dimensional (2D) materials and phenomena along with the development of a small, hermetically sealed cell. The hermetic cell is designed to assist with analyzing sensitive 2D materials outside of an inert environment. When working with van der Waals materials that are especially sensitive to oxygen or water, it can be difficult to identify usable thin flakes without exposing them to air. To help preserve materials for analysis in air, a capsule was designed that isolates the material in an inert environment. Although the capsule is hermetically sealed, the encapsulated material …

Two-Dimensional Black Phosphorus For Terahertz Emission And Near-Field Radiative Heat Transfer, Mahmudul Hasan Doha

Graduate Theses and Dissertations

The main focus of this work is to investigate two potential optical and optoelectronic applications of black phosphorus (BP): the near-field radiative heat transfer in plasmonic heterostructures with graphene and terahertz emission from multi-layer BP photoconductive antennas. When the separation distance between graphene-black phosphorene is much smaller than or comparable to the thermal wavelength at different temperatures, a near-field radiation heat transfer breaks the Planck blackbody limit. The magnitude of the near-field radiation enhancement acutely depends on the gate voltage, doping, and vacuum gap of the graphene and BP pair. The strong near-field radiation heat transfer enhancement of the specific …

Interferometric Lithography- An Approach To Large Area And Cost Effective Nanopatterning, Vineeth Sasidharan

Optical Science and Engineering ETDs

In this dissertation interferometric lithography is approached in two different ways to address two important constraints of nanopatterning. One approach solves the problem of scaling up interferometric lithography to wafer scale (4 inch or larger) area. Through the second approach we have developed a nanopatterning technique based on interferometric lithography by using an inexpensive (~$100) diode laser as source, making interferometric lithography a very cost-effective technique.

Wafer-scale large-area nanopatterning was developed using an amplitude grating mask as a grating beam splitter along with spatial averaging of laser intensity by wobbling. The longitudinal and transverse coherence issues both are eased by …

Crystal Structure Prediction Of Materials At Extreme Conditions, Ashley S. Williams

USF Tampa Graduate Theses and Dissertations

The prediction of the structure of a crystal given only the constituent elements is one of the greatest challenges in both materials science and computational science alike. If one were to try to predict a novel crystal by brute force, meaning by arranging the atoms in every possible position of the unit cell and optimizing the geometry to find the energy minima of the potential energy surface, the amount of computer resources required to complete the calculation on the timescale of a few years would vastly exceed the currently installed computational capacity of the entire world. Fortunately, several methods have …

Improvised Centrifugal Spinning For The Production Of Polystyrene Microfibers From Waste Expanded Polystyrene Foam And Its Potential Application For Oil Adsorption, Marco Laurence M. Budlayan, Jonathan N. Patricio, Jeanne Phyre B. Lagare, Susan D. Arco, Arnold C. Alguno, Antonio M. Basilio, Felmer S. Latayada, Rey Y. Capangpangan

Physics Faculty Publications

A straightforward approach to recycle waste expanded polystyrene (EPS) foam to produce polystyrene (PS) microfibers using the improvised centrifugal spinning technique is demonstrated in this work. A typical benchtop centrifuge was improvised and used as a centrifugal spinning device. The obtained PS microfibers were characterized for their potential application for oil adsorption. Fourier transform infrared spectroscopy results revealed similarity on the transmission bands of EPS foam and PS microfibers suggesting the preservation of the EPS foam’s chemical composition after the centrifugal spinning process. Scanning electron microscopy displayed well-defined fibers with an average diameter of 3.14 ± 0.59 μm. At the …

Optically Active Selenium Vacancies In Baga4Se7 Crystals, Brian C. Holloway, Timothy D. Gustafson, Christopher A. Lenyk, Nancy C. Giles, Kevin T. Zawilski, Peter G. Schunemann, Kent L. Averett, Larry E. Halliburton

Faculty Publications

Barium gallium selenide (BaGa₄Se₇) is a recently developed nonlinear optical material with a transmission window extending from 470 nm to 17 μm. A primary application of these crystals is the production of tunable mid-infrared laser beams via optical parametric oscillation. Unintentional point defects, such as selenium vacancies, cation vacancies (barium and/or gallium), and trace amounts of transition-metal ions, are present in BaGa₄Se₇ crystals and may adversely affect device performance. Electron paramagnetic resonance (EPR) and optical absorption are used to identify and characterize these defects. Five distinct EPR spectra, each representing an electron …

Texturing In Bi2Te3 Alloy Thermoelectric Materials: An Applied Physics Investigation, Oluwagbemiga P. Ojo

USF Tampa Graduate Theses and Dissertations

Thermoelectric devices provide the means for direct conversion between heat and electricity. The device conversion efficiency, or performance, is directly related to the thermoelectric figure of merit, ZT, of the working materials. Bismuth telluride alloys are the materials currently in use in most thermoelectric devices for near room temperature solid-state refrigeration and power conversion applications. The vast majority of publications in the literature on thermoelectricity report on investigations towards developing new materials with enhanced thermoelectric properties, however Bi₂Te₃ alloys have been used in thermoelectric devices for decades.

In this thesis, an investigation of crystallographic texturing on large …

Method Of Making Temperature-Immune Self-Referencing Fabry–Pérot Cavity Sensors, Hengky Chandrahalim, Jonathan W. Smith

AFIT Patents

A method of making passive microscopic Fabry-Pérot Interferometer (FPI) sensor includes forming a three-dimensional microscopic optical structure on a cleaved tip of an optical fiber that reflects a light signal back through the optical fiber. The reflected light is altered by refractive index changes in the three-dimensional structure that is subject to at least one of: (i) thermal radiation; and (ii) volatile organic compounds.

Improvements To Emissive Plume And Shock Wave Diagnostics And Interpretation During Pulsed Laser Ablation Of Graphite, Timothy I. Calver

Theses and Dissertations

This dissertation covers nanosecond pulsed laser ablation of graphite for 4-5.7 J/cm² fluences with 248 nm and 532 nm lasers in 1-180 Torr helium, argon, nitrogen, air, and mixed gas. Three experiments were performed to improve the interpretation of common diagnostics used to characterize pulsed laser ablation, find simple but universal scaling relationships for comparing dynamics across different materials and ablation conditions, and provide a systematic analysis of graphite emissive plume and shock wave dynamics. A scaling of the Sedov-Taylor energy ratio was developed and validated for a range of studies despite differences in wavelength, pulse duration, fluence, and …

Molecular Dynamics Simulations Of Self-Assemblies In Nature And Nanotechnology, Phu Khanh Tang

Dissertations, Theses, and Capstone Projects

Nature usually divides complex systems into smaller building blocks specializing in a few tasks since one entity cannot achieve everything. Therefore, self-assembly is a robust tool exploited by Nature to build hierarchical systems that accomplish unique functions. The cell membrane distinguishes itself as an example of Nature’s self-assembly, defining and protecting the cell. By mimicking Nature’s designs using synthetically designed self-assemblies, researchers with advanced nanotechnological comprehension can manipulate these synthetic self-assemblies to improve many aspects of modern medicine and materials science. Understanding the competing underlying molecular interactions in self-assembly is always of interest to the academic scientific community and industry. …

Fabrication And Characterization Of Photodetector Devices Based On Nanostructured Materials: Graphene And Colloidal Nanocrystals, Wafaa Gebril

Graduate Theses and Dissertations

Photodetectors are devices that capture light signals and convert them into electrical signals. High performance photodetectors are in demand in a variety of applications, such as optical communication, security, and environmental monitoring. Among many appealing nanomaterials for novel photodetection devices, graphene and semiconductor colloidal nanocrystals are promising candidates because of their desirable and unique properties compared to conventional materials.

Photodetector devices based on different types of nanostructured materials including graphene and colloidal nanocrystals were investigated. First, graphene layers were mechanically exfoliated and characterized for device fabrication. Self-powered few layers graphene phototransistors were studied. At zero drain voltage bias and room …