Materials Science and Engineering Commons^™

Spectroscopic Characterization Of Trivalent Holmium In Liyf4 And Bay2F8 Crystals, Vivian R. Hedberg

Theses and Dissertations

Yttrium-fluoride crystals doped with trivalent holmium are promising laser gain media for mid-infrared laser systems. To accurately model laser systems, a complete optical characterization of the laser gain medium is required. The key modeling parameters were obtained by a spectroscopic investigation of Ho³⁺ in LiYF₄ and BaY₂F₈ crystal hosts. Several important mid-infrared laser transitions were characterized at nominal Ho³⁺ ion concentrations of 10-30 at.%. Polarized emission cross-sections were determined from the fluorescence spectra using the Füchtbauer-Ladenburg method. Polarized absorption cross-sections were obtained using the Integral Reciprocity method. The upper-state lifetimes were measured at room …

The Behavior Of ½⟨111⟩ Screw Dislocations In W–Mo Alloys Analyzed Through Atomistic Simulations, Lucas A. Heaton, Kevin Chu, Adib J. Samin

Faculty Publications

Analyzing plastic flow in refractory alloys is relevant to many different commercial and technological applications. In this study, screw dislocation statics and dynamics were studied for various compositions of the body-centered cubic binary alloy tungsten–molybdenum (W–Mo). The core structure did not appear to change for different alloy compositions, consistent with the literature. The pure tungsten and pure molybdenum samples had the lowest plastic flow, while the highest dislocation velocities were observed for equiatomic, W_0.5Mo_0.5 alloys. In general, dislocation velocities were found to largely align with a well-established dislocation mobility phenomenological model supporting two discrete dislocation mobility regimes, …

Degradation Of The Mechanical Properties And Hydrogen Generation In Cement Under Gamma Irradiation Assessed By Atomistic Simulation, Omar Al Najjar

Theses and Dissertations

Although understanding the effect of the gamma-ray on cement-based materials is essential for many applications, such as the concrete contaminate of nuclear reactors or the storage of radioactive waste in cement-based waste forms, such understanding is still not fully developed. The importance of having such an understanding is becoming of utmost importance, especially with calls to extend the lifetime of nuclear power plants, and also due to some recent incidents of failures of the concrete structure in the nuclear fields. In this work, the details of preparing three molecular models as a representative structure of the main binding phase of …

Residual Optical Absorption From Native Defects In Cdsip2 Crystals, Timothy D. Gustafson, Nancy C. Giles, Elizabeth M. Scherrer, Kevin T. Zawilski, Peter G. Schunemann, Kent L. Averett, Jonathan E. Slagle, Larry E. Halliburton

Faculty Publications

CdSiP₂ crystals are used in optical parametric oscillators to produce tunable output in the mid-infrared. As expected, the performance of the OPOs is adversely affected by residual optical absorption from native defects that are unintentionally present in the crystals. Electron paramagnetic resonance (EPR) identifies these native defects. Singly ionized silicon vacancies (V^-_Si) are responsible for broad optical absorption bands peaking near 800, 1033, and 1907 nm. A fourth absorption band, peaking near 630 nm, does not involve silicon vacancies. Exposure to 1064 nm light when the temperature of the CdSiP₂ crystal is near 80K converts …

Vaccine Immunogenicity Versus Gastrointestinal Microbiome Status: Implications For Poultry Production, Chrysta N. Beck, Jiangchao Zhao, Gisela F. Erf

Poultry Science Faculty Publications and Presentations

At the turn of the 21st century, the importance of maintaining a balanced microbiome was brought to the forefront of the microbiology, immunology, and physiology research fields. Exploring the complex interactions between vaccine administration, mucosal microbiome, oral tolerance, and enteric inflammation in health and disease is challenging since environmental factors (such as diet and sanitation) have major influences on gut microbiota composition. High enteric pathogen load has been shown to contribute to dampened cell-mediated and humoral immune responses to vaccines in human case studies, either through elevated enteric inflammation or increased tolerance to environmental microbes. Although antibiotic and probiotic interventions …

Preparation Of 2d Tungsten Diselenide (Wse2) Thin Films By Selenization Of Dc-Sputtered W Precursors, Lwitiko P. Mwakyusa

Tanzania Journal of Science

Two-dimensional layered transition metal dichalcogenides based on WSe2 films demonstrated promising properties for nano-electronics and photovoltaic applications. In this work, WSe2 films were prepared by selenization of DC-sputtered W precursors. The influence of the selenization temperature on the structural, morphology, and optical properties of the WSe2 films was investigated. The selenization temperature was varied from 350 °C to 450 °C at the interval of 50 °C. Structural, morphology and optical properties of the WSe2 were investigated using X-ray diffractometry (XRD), Atomic Force Microscope (AFM), and UV-VIS-NIR spectrophotometer, respectively. XRD analysis revealed that all WSe2 were polycrystalline and exhibited the co-existence …

Electrochromic Polymers: From Electrodeposition To Hybrid Solid Devices, Haradou Sare, Dongmei Dong

College of Science & Mathematics Departmental Research

This paper reports on the linear colorimetric and electrochromic (EC) characteristics of electrodeposited polyaniline (PANI) films. This paper also investigates the infrared EC properties of acid-doped PANI films. The electrochemical polymerization method was employed to create a porous and thin PANI film layer onto PET-ITO substrates. This layer was capped with WO3 film to create a gel electrolyte sandwich structure that demonstrates the compatibility of PANI films with cathodic WO3 films in full devices. The electrodeposition of the film was fabricated by applying different voltages and time, with the optimal film quality achieved with the 1.7 V voltage and a …

Enhancing Scanning Tunneling Microscopy With Automation And Machine Learning, Darian Smalley

Graduate Thesis and Dissertation 2023-2024

The scanning tunneling microscope (STM) is one of the most advanced surface science tools capable of atomic resolution imaging and atomic manipulation. Unfortunately, STM has many time-consuming bottlenecks, like probe conditioning, tip instability, and noise artificing, which causes the technique to have low experimental throughput. This dissertation describes my efforts to address these challenges through automation and machine learning. It consists of two main sections each describing four projects for a total of eight studies.

The first section details two studies on nanoscale sample fabrication and two studies on STM tip preparation. The first two studies describe the fabrication of …

A Simple, Inexpensive Alkaline Method For Bacterial Dna Extraction From Environmental Samples For Pcr Surveillance And Microbiome Analyses, Abdulkarim Shwani, Bin Zuo, Adnan Alrubaye, Jiangchao Zhao, Douglas D. Rhoads

Poultry Science Faculty Publications and Presentations

DNA extraction for downstream molecular diagnostic applications can be an expensive, time-consuming process. We devised a method to quickly extract total bacterial DNA from environmental samples based on the sodium hydroxide lysis of cells with or without capture by magnetic beads for subsequent PCR or quantitative PCR. The final DNA extraction method using NaOH is extremely low-cost and can be completed in as little as 10 min at room temperature with dilution, or the DNA can be further purified using silica-coated paramagnetic beads. NaOH extraction was effective for Gram-negative and Gram-positive bacteria in samples from air, soil, sewage, food, laboratory …

Thermal Diffusivity And Acoustic Properties Of Nb Thin Films Studied By Time-Domain Thermoreflectance, Md. Obidul Islam, Hani Elsayed-Ali

Electrical & Computer Engineering Faculty Publications

The thermal diffusion and acoustic properties of Nb impacts the thermal management of devices incorporating Nb thin films such as superconducting radiofrequency (SRF) cavities and superconducting high-speed electronic devices. The diffusion and acoustic properties of 200-800 nm thick Nb films deposited on Cu substrates were investigated using time-domain thermoreflectance (TDTR). The films were examined by X-ray diffraction, scanning electron microscopy, and atomic force microscopy. The grain size and thermal diffusivity increase with film thickness. The thermal diffusivity increased from 0.100± 0.002 cm²s^-1 to 0.237± 0.002 cm²s^-1 with the increase in film thickness from 200 …

Direct Measurement Of Microwave Loss In Nb Films For Superconducting Qubits, B. Abdisatarov, D. Bafia, A. Murthy, G. Eremeev, H. E. Elsayed-Ali, J. Lee, A. Netepenko, C. P. A. Carlos, S. Leith, G. J. Rosaz, A. Romanenko, A. Grassellino

Electrical & Computer Engineering Faculty Publications

Niobium films are a key component in modern two-dimensional superconducting qubits, yet their contribution to the total qubit decay rate is not fully understood. The presence of different layers of materials and interfaces makes it difficult to identify the dominant loss channels in present two-dimensional qubit designs. In this paper, we present the study that directly correlates measurements of RF losses in such films to material parameters by investigating a high-power impulse magnetron sputtered (HiPIMS) film atop a three-dimensional niobium superconducting radio frequency (SRF) resonator. By using a 3D SRF structure, we are able to isolate the niobium film loss …

Effect Of Annealing On Photoluminescence From Defects In Gan, Oleksandr Andrieiev

Theses and Dissertations

Annealing is a critical process in modern GaN technology, essential for achieving p-type conductivity by activating the Mg_Ga acceptor, as first demonstrated by Shuji Nakamura in the early 1990s. Despite the omnipresence of hydrogen as an impurity in GaN crystals, the precise mechanisms governing hydrogen diffusion and acceptor passivation remain only partially understood. The presented research investigates the effects of annealing-induced activation and hydrogen passivation on C and Be acceptors in GaN grown by MOCVD, HVPE, and MBE methods. We explored these effects by using several annealing techniques, gas compositions, and thermal regimes. A transient behavior between the C …

Structural And Magnetic Properties Of Molecular Beam Epitaxy (Mnsb2te4)X(Sb2te3)1−X Topological Materials With Exceedingly High Curie Temperature, Candice R. Forrester, Christophe Testelin, Kaushini Wickramasinghe, Ido Levy, Dominique Demaille, David Hrabovsky, Xiaxin Ding, Lisa Krusin-Elbaum, Gustavo Lopez, Maria C. Tamargo

Publications and Research

Tuning the properties of magnetic topological materials is of interest to realize exotic physical phenomena, new quantum phases and quasiparticles, and topological spintronic devices. However, current topological materials exhibit Curie temperature (T_C) values far below those needed for practical applications. In recent years, significant progress has been made to control and optimize T_C, particularly through defect-engineering of these structures. Most recently, we reported T_C values up to 80 K for (MnSb₂Te₄)_x(Sb₂Te₃)_1−x when 0.7 ≤ x ≤ 0.85 by controlling the composition x and the …

Processing, Stability, And High-Temperature Properties Of Doped Lacro3-Based Refractory Ceramics And Composites For Harsh Environments Sensing Applications, Javier A. Mena

Graduate Theses, Dissertations, and Problem Reports (ETD)

In order to test and monitor the operational stability and conditions of various energy, transportation, and manufacturing systems and their components, accurate sensors capable of operating at temperatures over 1000 °C in various environments for long durations are required. In addition, many of these harsh environmental systems do not permit sensors to be directly inserted into the environment, so the sensors need to be embedded into the surrounding support or thermal protective materials. Some technological and industrial applications that require the use of harsh environment conditions sensing include nuclear and chemical reactors, jet engines, heavyduty gas turbines, rotating bearings in …

Mechanisms Of Dendritic Shorting In Lithium Metal Batteries With Li7la3zr2o12 Solid Electrolytes, Lukas Karapin-Springorum

Pomona Senior Theses

Energy storage will play a crucial role in efforts to mitigate the effects of climate change caused by greenhouse gas emissions from human activity. Lithium metal batteries using solid electrolytes like Li₇La₃Zr₂O₁₂ have higher energy density than lithium-ion batteries, which may enable a more rapid and complete electrification of transportation. However, lithium metal batteries suffer from undesirable short-circuiting when metallic lithium deposits connect the two electrodes. It has been debated whether these lithium dendrites generally grow directionally from the anode or are generated by the reduction of lithium ions inside the solid electrolyte, …

Ltspice Modeling For Gan-Git Hemt Including Cryogenic Temperature, Md Maksudul Hossain, Yuqi Wei, H. Alan Mantooth

Electrical Engineering Faculty Publications and Presentations

Highly efficient electrically driven avionics have led to a renewed interest in cryogenic propulsion systems with the goal of reducing carbon emission footprint. Although cryogenic converters promise better efficiency and improved power density, the successful design is incumbent upon the appropriate switching device selection and simulation-based analyses prior to initial prototyping. In this work, a datasheet-driven compact model for a gallium nitride (GaN) Gate Injection Transistor (GIT) has been proposed and implemented in LTspice, a versatile, high performance, and free circuit simulator in order to investigate the merit of the chosen device in a power electronic system.

“Zero” Porosity High Loading Nmc622 Positive Electrodes For Li-Ion Batteries, Haidar Y. Alolaywi, Kubra Uzun, Yang-Tse Cheng

Chemical and Materials Engineering Faculty Publications

LiNi0.6 Mn0.2Co0.2 O 2 (NMC622) is a widely used positive electrode material for lithium-ion batteries, including electric vehicles. In this work, we investigated the effects of porosity, ranging from “zero” to the typical 35%, on the electrochemical behavior of high- loading NMC622 electrodes. Although it is well known that the energy density of the electrode increases with increasing areal capacity and decreasing porosity, NMC-positive electrodes with exceedingly low porosity (e.g., near zero) and high loading (e.g., 4 mAh cm−2 ) have not been investigated. Here, we report an intriguing observation that the “zero porosity” NMC electrode can have higher capacity …

Design And Performance Of Superconducting Switches For Nanowire Detectors In Magnetic Fields, Timothy James Draher

Graduate Research Theses & Dissertations

Superconducting nanowire devices fit a broad spectrum of applications, including particle detection and quantum computing, and their expanding use across various fields highlights their role in the hybridization of superconducting and conventional semiconductor electronics. Despite their potential, the low signal output of these devices raises challenges in scalability and integration, particularly in applications for nuclear and high-energy physics, where resilience in magnetic fields is becoming a critical optimization factor. The superconducting nanowire cryotron (nTron) addresses these issues by providing operational gain and logic switching in superconducting nanowire circuits, demonstrating adaptability to multiple materials. This dissertation focuses on modifying the conventional …

Gan Hemt And Air Core Magnetics Based Power Converters Evaluations At Cryogenic Temperature, Yuqi Wei, Md Maksudul Hossain, H. Alan Mantooth

Electrical Engineering Faculty Publications and Presentations

Cryogenic power electronics is both advantageous and indispensable in many applications, like deep space probe, military electric vehicle, magnetic resonance imaging etc. Among different semiconductors, the gallium nitride (GaN) high electron mobility transistor (HEMT) is the most promising candidate for cryogenic applications with significant conduction loss and switching loss reductions. Moreover, there is no carrier freeze out effect for the GaN HEMTs, which is applicable in extreme low temperature operating conditions. In this work, the efficiency of GaN HEMTs based power converters with different power levels (from several Watts to several kiloWatts) are evaluated at cryogenic temperature. Three different commercial …

Photoluminescence Of Beryllium-Related Defects In Gallium Nitride, Mykhailo Vorobiov, Mykhailo Vorobiov

Theses and Dissertations

This study explores the potential of beryllium (Be) as an alternative dopant to magnesium (Mg) for achieving higher hole concentrations in gallium nitride (GaN). Despite Mg prominence as an acceptor in optoelectronic and high-power devices, its deep acceptor level at 0.22 eV above the valence band limits its effectiveness. By examining Be, this research aims to pave the way to overcoming these limitations and extend the findings to aluminum nitride and aluminum gallium nitride (AlGaN) alloy. Key contributions of this work include. i)Identification of three Be-related luminescence bands in GaN through photoluminescence spectroscopy, improving the understanding needed for further material …

Halide-Assisted Growth Of Transition Metal Dichalcogenides, Vinaayak Sivam Balasubramaniam

Dissertations, Master's Theses and Master's Reports

Monolayers of transition metal dichalcogenides (TMDCs) have attracted significant attention as the rare two-dimensional (2D) semiconducting materials with a direct energy band gap. Chemical vapour deposition (CVD) is one of the scalable techniques to grow atomically thin TMDC monolayers in high quality, but it requires high growth temperature. Herein we report the growth of MoS2, WS2 and MoSe2 by a one-step halide-assisted CVD method using NaCl and KCl as the catalysts. These halides could reduce the growth temperature of TMDCS by reacting with the precursors (TMDC powders) to form volatile intermediate compounds as the growth species. We use optical microscopy, …

Reducing Food Scarcity: The Benefits Of Urban Farming, S.A. Claudell, Emilio Mejia

Journal of Nonprofit Innovation

Urban farming can enhance the lives of communities and help reduce food scarcity. This paper presents a conceptual prototype of an efficient urban farming community that can be scaled for a single apartment building or an entire community across all global geoeconomics regions, including densely populated cities and rural, developing towns and communities. When deployed in coordination with smart crop choices, local farm support, and efficient transportation then the result isn’t just sustainability, but also increasing fresh produce accessibility, optimizing nutritional value, eliminating the use of ‘forever chemicals’, reducing transportation costs, and fostering global environmental benefits.

Imagine Doris, who is …

Combined Risk Based Inspection And Fault Tree Analysis For Repetitive 3-Phase Line Piping Leakage At West Java Offshore Topside Facility, Dona Yuliati, Akhmad Herman Yuwono, D. Rizal Asral, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Hydrocarbon releases might result in serious consequences in various aspects. In addition to the contribution to environmental pollution, repetitive leakages need high repair costs. This study aim is to minimize potential repetitive leakage for other typical 3-phase piping systems. We conducted the risk assessment by adopting Risk Based Inspection (RBI) API 581 to identify risk level, calculating piping lifetime, recommended inspection plan and mitigations. The most relevant root causes can be obtained through quantitative Fault Tree Analysis (FTA). Observation and investigation was taken from eight 3-phase piping systems that experienced repetitive leakages. It has been found that the risk level …

Nitrogen Gas Quenching Pressure Effect On Bs S155 Alloy Steel In Vacuum Furnace, Agus Mulyadi Hasanudin, Eddy Sumarno Siradj

Journal of Materials Exploration and Findings

The production of metal and alloy products requires the use of heat treatment, when during the heat treatment process, quenching is a crucial step. The quenching medium can be anything from water, a salt bath, oil, air and gas. In a vacuum furnace, pressurized gas, most frequently nitrogen (N₂) gas, serves as one of the quenching mediums. One of the drawbacks of the quenching process is the distortion and dimensional change of the parts. This paper aims to investigate the influence of nitrogen gas quenching pressure on the distortion and dimensional change of aerospace actuator gear planet parts …

Radiation Exposure Calibration Of The Al2o3:C With Radium-226 And Cesium-137 Using The Osl Method, Selma Tepeli Aydin

All Theses

Optically stimulated luminescence (OSL) dosimetry was utilized to calibrate Al₂O₃:C powder dosimeters, available commercially as the nanoDot® from Landauer Inc., and compare the dosimeter response to radium-226 (²²⁶Ra) and cesium-137 (¹³⁷Cs). The signal from the OSL was quantified using a microSTARii^® OSL reader also produced by Landauer Inc. Dose-response curves were developed for ²²⁶Ra and ¹³⁷Cs experiments (5 dosimeters each) at thirteen absorbed doses. Individual dosimeter response was tracked by serial number. Linear regression analysis was performed to determine if there were significant differences between the intercepts of the …

Analyzing The Effects Of Ultrafast Laser Processing On Mechanical Properties Of 3d-Printed Pla Parts, Darshan Pramodbhai Yadav

Theses and Dissertations

Recent advances in additive manufacturing technologies have already led to wide-scale adoption of 3D-printed parts in various industries. The expansion in choice of materials that can be processed, particularly using Fused Deposition Modeling (FDM), and the steady advancements in dimensional accuracy control have extended the range of applications far beyond rapid prototyping. However, additive manufacturing still has considerable limitations compared to traditional and subtractive manufacturing processes. This work addresses limitations associated with the as-deposited surface roughness of 3D-printed parts. The effects of roughness-induced stress concentrations were studied on ultimate tensile strength and fatigue life. The samples were manufactured using a …

Design And Characterization Of A Novel Eef2k Degrader With Potent Therapeutic Efficacy Against Triple-Negative Breast Cancer, Changxin Zhong, Rongfeng Zhu, Ting Jiang, Sheng Tian, Xiaobao Zhao, Xiaoya Wan, Shilong Jiang, Zonglin Chen, Rong Gong, Linhao He, Jin-Ming Yang, Na Ye, Yan Cheng

Markey Cancer Center Faculty Publications

Dysregulated eEF2K expression is implicated in the pathogenesis of many human cancers, including triple-negative breast cancer (TNBC), making it a plausible therapeutic target. However, specific eEF2K inhibitors with potent anti-cancer activity have not been available so far. Targeted protein degradation has emerged as a new strategy for drug discovery. In this study, a novel small molecule chemical is designed and synthesized, named as compound C1, which shows potent activity in degrading eEF2K. C1 selectively binds to F8, L10, R144, C146, E229, and Y236 of the eEF2K protein and promotes its proteasomal degradation by increasing the interaction between eEF2K and the …

Characterization Of Interlayer Laser Shock Peening During Fused Filament Fabrication Of Polylactic Acid (Pla), Fabien Denise

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The field of additive manufacturing (AM) has gained a significant amount of popularity due to the increasing need for more sustainable manufacturing techniques and the adaptive development of complex product geometries. The problem is that AM parts routinely exhibit flaws or weaknesses that affect functionality or performance. Over the years, surface treatments have been developed to compensate certain flaws or weaknesses in manufactured products. Combining surface treatments with the modularity of additive manufacturing could lead to more adaptable and creative improvements of product functions in the future. The current work evaluates the feasibility of pursuing a new research axis in …

Effect Of Hf Alloying On Magnetic, Structural, And Magnetostrictive Properties In Feco Films For Magnetoelectric Heterostructure Devices, Thomas Mion, Margo Staruch, Konrad Bussmann, Goran Karapetrov, Olaf Van 'T Erve, Sara Mills, Heonjune Ryou, Ramasis Goswami, Patrick G. Callahan, David J. Rowenhorst, Syed B. Qadri, Samuel Lofland, Peter Finkel

College of Science & Mathematics Departmental Research

Materials with high magnetoelectric coupling are attractive for use in engineered multiferroic heterostructures with applications such as ultra-low power magnetic sensors, parametric inductors, and non-volatile random-access memory devices. Iron-cobalt alloys exhibit both high magnetostriction and high saturation magnetization that are required for achieving significantly higher magnetoelectric coupling. We report on sputter-deposited (Fe0.5Co0.5)1-xHfx (x = 0 - 0.14) alloy thin films and the beneficial influence of Hafnium alloying on the magnetic and magnetostrictive properties. We found that co-sputtering Hf results in the realization of the peening mechanism that drives film stress from highly tensile to slightly compressive. Scanning electron microscopy and …

Quantitative, Photocurrent Multidimensional Coherent Spectroscopy, Adam Halaoui

Electronic Theses and Dissertations

Multidimensional coherent spectroscopy (MDCS) is a quickly growing field that has a lot of advantages over more conventional forms of spectroscopy. These advantages all come from the fact that MDCS allows us to get time resolved correlated emission and absorption spectra using very precisely chosen interactions between the density matrix and the excitation laser. MDCS spectra gives the researcher a lot of information that can be extracted purely through qualitative analysis. This is possible because state couplings are entirely separated on the spectra, and once we know how to read the data, we can see how carriers transport in the …