Materials Science and Engineering Commons^™

Abrasion Resistance Of High Early-Strength Concrete For Rapid Repair, Nader Ghafoori, Matthew O. Maler, Meysam Najimi, Ariful Hasnat

Civil and Environmental Engineering and Construction Faculty Research

This paper examines the abrasion resistance of high early-strength concrete developed for rapid repair of highways and bridge decks. The cement types chosen for this study included ASTM Type III, ASTM Type V, and Calcium Sulfoaluminate (CSA) cements. A cement content of 386 kg/m3 (650 lb/yd3 ) was maintained for all studied concretes. Test samples were tested after 24 hours and 28 days of curing in order to evaluate compressive strength and depth of wear. Test results revealed that the opening time to attain minimum required compressive strength for CSA cement concrete was one hour, whereas the values for Type …

Computational And Experimental Approach To Understanding The Structural Interplay Of Self-Assembled End-Terminated Alkanethiolates On Gold Surfaces, Juganta K. Roy, Erick S. Vasquez, Henry P. Pinto, Swati Kumari, Keisha B. Walters, Jerzy Leszcynski

Chemical and Materials Engineering Faculty Publications

Applications of self-assembled monolayers (SAMs) on surfaces are prevalent in modern technologies and drives the need for a better understanding of the surface domain architecture of SAMs. To explore structural interaction at the interface between gold surfaces and a hydroxyl-terminated alkanethiol, 11-hydroxy-1-undecanethiol, (C11TH) we have employed a combined computational and experimental approach. Density functional theory (DFT) calculations were carried out on the thiol–gold interface using both the Perdew–Burke–Ernzerhof (PBE) and van der Waals (optB86b) density functionals. Our ab initio molecular dynamics (AIMD) simulations revealed that the interface consists of four different distinguished phases, each with different C11TH orientations. Experiments involved …

Optimizing The Valorization Of Industrial By-Products For The Induction Healing Of Asphalt Mixtures, Amir Tabakovic, Marta Vila-Cortavitarte, Daniel Jato-Espino, Daniel Castro-Fresno

Articles

Self-healing within asphalt pavements is the process whereby road cracks can be repaired automatically when thermal and mechanical conditions are met. To accelerate and improve this healing process, metal particles are added to asphalt mixtures. However, thisapproach is costly both in economic and environmental terms due to the use of virgin metallic particles. So, even though the self-healing of asphalt mixtures has been widely addressed in experimental terms over the years, there is a lack of research aimed at modelling this phenomenon, especially with the purpose of optimizing the use of metal particles through the valorization of industrial by-products. As …

Hydcem: A New Cement Hydration Model, Niall Holmes, Denis Kelliher, Mark Tyrer

Conference papers

Hydration models are useful to predict, understand and describe the behaviour of different cementitious-based systems. They are indispensable for undertaking long-term performance and service life predictions for existing and new products for generating quantitative data in the move towards more sustainable cements while optimising natural resources. One such application is the development of cement-based thermoelectric applications.

HYDCEM is a new model to predict the phase assemblage, degree of hydration, heat release and changes in pore solution chemistry over time for cements undergoing hydration for any w/c ratio and curing temperatures up to 450C. HYDCEM, written in MATLAB, is aimed at …

Development Of Experimental And Finite Element Models To Show Size Effects In The Forming Of Thin Sheet Metals, Jeffrey D. Morris

LSU New Orleans Theses and Dissertations

Abstract

An experimental method was developed that demonstrated the size effects in forming thin sheet metals, and a finite element model was developed to predict the effects demonstrated by the experiment. A universal testing machine (UTM) was used to form aluminum and copper of varying thicknesses (less than 1mm) into a hemispherical dome. A stereolithography additive manufacturing technology was used to fabricate the punch and die from a UV curing resin. There was agreement between the experimental and numerical models. The results showed that geometric size effects were significant for both materials, and these effects increased as the thickness of …

Elimination Of Empirical, Ineffective And Expensive Pg Plus Tests To Characterize Modified Binders, Zahid Hossain, Ashraf Elsayed, Mm Tariq Morshed, Mohammad Hassan

Data

Corresponding data set for Tran-SET Project No. 18BASU02. Abstract of the final report is stated below for reference:

"For characterizing the polymer modified binders, different state Departments of Transportation (DOTs) use different time consuming and empirical Performance Grade (PG) Plus test methods. Furthermore, the PG Plus tests are silent when asphalt binders are modified with chemicals such as polyphosphoric acid (PPA). But, the effects of the elastomeric or plastomeric polymer are not accurately identified through these conventional tests such as Elastic Recovery (ER) and tenacity. Thus, the main research goal of this study is to recommend alternative test method(s), which …

Development Of A Methodology For Characterizing Reaction Kinetics, Rheology, And In-Situ Compaction Of Polyimide Prepregs During Cure, James Raymond Magato, Donald A. Klosterman

Chemical and Materials Engineering Faculty Publications

PMR-type polyimide prepregs are challenging to fabricate into high quality composites due to volatiles that are generated and must be removed in situ during processing. The current work was conducted to develop accurate, reliable, and practical characterization techniques of the prepreg rheology, volatile generation, and subsequent volatile removal from the prepreg during composite fabrication. Thermal analysis was used to characterize volatile generation, reaction rates, and rheology. A novel approach was used to measure the thickness of the prepreg in situ during vacuum bag/oven processing using a high-temperature LVDT. Experimental results are presented for the commercially available RM-1100 polyimide/carbon prepreg system, …

Elimination Of Empirical, Ineffective And Expensive Pg Plus Tests To Characterize Modified Binders, Zahid Hossain, Ashraf Elsayed, Mm Tariq Morshed, Mohammad Hassan

Publications

For characterizing the polymer modified binders, different state Departments of Transportation (DOTs) use different time consuming and empirical Performance Grade (PG) Plus test methods. Furthermore, the PG Plus tests are silent when asphalt binders are modified with chemicals such as polyphosphoric acid (PPA). But, the effects of the elastomeric or plastomeric polymer are not accurately identified through these conventional tests such as Elastic Recovery (ER) and tenacity. Thus, the main research goal of this study is to recommend alternative test method(s), which can possibly be pursued by using a commonly available device, a Dynamic Shear Rheometer (DSR). Three PG binders …

Use Of Rice Husk Ash (Rha) In Flowable Fill Concrete Mix Material, Zahid Hossain, Kazi Tamzidul Islam

Publications

In the way of finding sustainable development, the flowable fill is a relatively new construction technology. Flowable fill is a self-compacting material, which has been developed in recent years. Flowable fill has been used for different applications such as backfilling walls, sewer trenches, bridge abutments, conduit trenches, pile excavations, and retaining walls. This study examines the potential uses of Rice Husk Ash (RHA) as a sustainable cementitious material (SCM) in the preparation of flowable fill concrete. (RHA is an agricultural by-product of the rice milling process. This study has evaluated the usage of RHA in producing low strength and self-consolidating …

Self-Healing Concrete Using Encapsulated Bacterial Spores In A Simulated Hot Subtropical Climate, Marwa Hassan, Jose Milla, Tyson Rupnow, Ahsennur Soysal

Publications

Bacterial concrete has become one of the most promising self-healing alternatives due to its capability to seal crack widths through microbial induced calcite precipitation (MICP). In this study, two bacterial strains were embedded at varying dosages (by weight of cement) in concrete. Beam specimens were used to identify the maximum crack-sealing efficiency, while cylinder samples were used to determine their effects on the intrinsic mechanical properties, as well as its stiffness recovery over time after inducing damage. The concrete specimens were cured in wet-dry cycles to determine their feasibility in Region 6. The results showed that the specimen groups with …

Use Of Bagasse Ash As A Concrete Additive For Road Pavement Application, Gabriel Arce, Marwa Hassan, Maria Gutierrez, Michele Barbato

Publications

The objective of this study was to evaluate the use of sugarcane bagasse ash (SCBA) as a partial replacement of cement in concrete for road pavement application. The study explored the pozzolanic activity of SCBA produced from three different processing methodologies (i.e., raw SCBA, controlled SCBA and post-processed SCBA). The experimental results revealed that SCBA produced by the controlled burning of sugarcane bagasse fiber (SBF) at 650°C and grinding (C-650), presented the maximum pozzolanic activity. However, this SCBA production process was deemed challenging for large-scale industrial application due to low SCBA yield (i.e., 3 to 6%). On the other hand, …

Manipulating Fiber Orientation For The Reduction Of Warpage In Carbon Fiber Composite Sandwich Panels, Landon Burnley, Gabrielle Correia

Materials Engineering

Safran Cabin (Santa Maria, CA), previously known as Zodiac Aerospace, designs and manufactures interior cabin components for private and commercial aircraft. Carbon fiber face sheets have recently been incorporated in their overhead luggage bin assemblies which utilize a composite sandwich panel design, in order to provide additional stiffness to the previous glass fiber sandwich panels. Since the introduction of carbon fiber in these luggage bin panels, Safran has experienced an increase in warpage during manufacturing. When inspected by quality control, the panels are tested mimicking how they are installed in aircraft. If the panels do not meet specifications, the warped …

Experimental And Theoretical Evaluation Of The Effect Of Panel Geometry On The Failure Of Corrugated Board Panel, Takashi Takayama, Katsuhiko Saito, Akira Higashiyama

Journal of Applied Packaging Research

McKee’s formula is widely used to predict the compression strength (CS) of corrugated boxes and panels. It can accurately estimate the compression strength of boxes that are within a practical size range, but recently, larger and smaller corrugated boxes than before have been extensively developed. Therefore, there is a need for a CS prediction formula that works beyond the application range of McKee’s formula. Recent researches consider the failure mode as a combination of collapsing and buckling failure and remove the constraints and the assumptions associated with McKee’s formula. This makes it possible to more accurately estimate the CS of …

Erosion Resistance Of Tungsten-Carbide Coatings For Steel Pipes In Fluid Catalytic Cracking Units, Davis Vannasing, Jennifer Hulfachor

Materials Engineering

In petroleum processing, the flow of catalyst readily leads to erosion of piping in a fluid catalytic cracking unit. Advances in coating materials and processes necessitate a re-evaluation of current protection methods. Commercially available tungsten-carbide (WC) claddings and nanostructured WC-W CVD coatings were investigated as potential alternative erosion-resistant coatings. Erosion tests by solid particle impingement were conducted on 2 variations of claddings and 1 variation of WC-W coatings following ASTM standard G76. A36 steel coupons were used as reference samples. For statistical validation, 2-3 replications of the tests were performed for the claddings and WC-W coating. Testing was conducted using …

Investigation Of Copper Infiltration Alloys For Use In Metal Matrix Composite Drill Bits, Samuel J. Stueland, Timothy P. Markiewicz

Materials Engineering

A newly developed copper-based alloy, P98-X1 was tested for compressive strength to predict qualitative performance compared to MF53, F-Bronze, CuNiSn, and CuMnNi for use as the infiltration alloy in metal matrix composite (MMC) drill bits. Ingots of each alloy were cast using an arc furnace and cut into compression testing samples using wire electrical discharge machining (EDM). The alloys were selected for testing based on solid solution strengthening coefficient and melting point. Five of each alloy were compression tested to determine yield strength of the infiltration alloy. Yield strength was determined using a 0.002mm displacement offset from the linear elastic …

Effects Of Heat Treatment On The Dimensional Stability And Mechanical Properties Of Guadua Bamboo, Kade Schmitz, Skye Dascher, Shalto Dascher

Materials Engineering

Contributing to about 4% of particulate emissions, the construction industry is one of the largest polluters of the environment. In an effort to reduce emissions, BamCore has produced a dual panel wall system made of Guadua bamboo with a Douglas fir veneer. Bamboo is a highly renewable material with a fast growth rate and carbon sequestration abilities. This project investigates how heat treating Guadua bamboo influences its dimensional changes and mechanical properties for building applications. It was found that a dimensional increase in every direction occurred for all samples when exposed to higher relative humidity (50% to 90%), and that …

A Study And Simulation Of Flux Induced Corrosion In Copper Tubing Used For The Distribution Of Potable Water, Daniel O. Benham

Materials Engineering

Water side corrosion within copper plumbing can occur due to a wide variety of unwanted circumstances. Through the controlled immersion of six ¾” copper tubing samples with five utilizing a unique industry standard soldering flux, this investigation associates residual flux deposits with the initiation of pitting in copper. Water stagnation in a copper potable water distribution system, typically associated with an infrequently used faucet, is a condition highly prone to copper pitting. A test apparatus designed to produce a partially stagnant flow condition with scheduled electrolyte flushes every 3 days was developed and constructed to contain 6 test samples for …

Mechanical Tear Testing And Failure Analysis Of Armordillo® Textile For Future Comparison With Next Generation Replacement Textiles, Jordan Bryce Pohl

Materials Engineering

ArmorDillo^® is a heavy-duty, waterproof textile designed to protect valuable equipment against outdoor elements such as rain, dirt, salt, ultraviolet rays, and damage from other external factors that is manufactured by Transhield^® USA and is currently in service with many branches of the United States Armed Forces, primarily the United States NAVY. Due to emerging security threats to classified military hardware the US NAVY through the United States Naval Surface Warfare Center (NSWC) is actively researching and sourcing a textile replacement for ArmorDillo^® to meet these threats. This study investigates the mechanical durability of ArmorDillo^® under …

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …

Investigating The Rapid Curing Possibility Of Geopolymer Concrete, Ashlesh Banjara

Master's Theses

Recent studies of heat-cured fly ash based green geopolymer concrete have shown its suitability for fabrication of structural members. Fabrication of these structural members requires continuous moderate heating (145°F) for 24 hrs, and an oven essential, for a large member can quickly turn into an energy guzzler, potentially eliminating the green credentials of the product. The proposed research involves the development of a frontal polymerization (FP) method that achieves rapid curing of geopolymer at ambient condition after short-term heat application. Initial work shows thermal FP in geopolymer is a possibility and might be a solution to the problem. The process …

The Effect Of Fabric Architecture On The Processing And Properties Of Composites Made By Vacuum Assisted Resin Transfer Molding, Francois Ntakobatagize, Oscar Ntakontagize, Donald A. Klosterman

Chemical and Materials Engineering Faculty Publications

The goal of this research project was to evaluate and compare the effect of fabric architecture on the processing and properties of composites made by Vacuum Assisted Resin Transfer Molding (VARTM). The fabric architectures investigated included plain weave, satin weave, and warp-knit unidirectional. The fiber types included E-glass and standard modulus carbon fiber. Flat panels were fabricated with a lab scale VARTM process using an epoxy resin system. Fabric plies were cut to 45 cm x 30 cm (18 in. x 12 in.), and the number of plies used depended on the fiber areal weight of each fabric to produce …

Fracture Toughness Improvement Of ����� Ceramics By Grain Size Control And Ductile Phase Reinforcement, Kesong Wang

McKelvey School of Engineering Graduate Student Theses & Dissertations

This study used grain size control and ductile phase reinforcement to improve fracture toughness of ����� ceramics. Alpha alumina particles of 100 nm, 0.5-1 micrometers, and 10 micrometers were coated with 1-5 nm nickel by electroless nickel plating (ENP). The coated powders were consolidated at 1200℃-1500℃ by spark plasma sintering (SPS). The sintered samples were annealed at 1100 oC for 1.5 hours and 10 hours to determine the effect of post sintering annealing on hardness and fracture toughness. Density of the samples were measured by the standard Archimedes method using a 5 mL pycnometer. Hardness values were determined by Vickers …

Application Of X-Ray Grating Interferometry To Polymer/Flame Retardant Blends In Additive Manufacturing, Omoefe Joy Kio

LSU Doctoral Dissertations

X-ray grating interferometry is a nondestructive tool for visualizing the internal structures of samples. Image contrast can be generated from the absorption of X-rays, the change in phase of the beam and small-angle X-ray scattering (dark-field). The attenuation and differential phase data obtained complement each other to give the internal composition of a material and large-scale structural information. The dark-field signal reveals sub-pixel structural detail usually invisible to the attenuation and phase probe, with the potential to highlight size distribution detail in a fashion faster than conventional small-angle scattering techniques. This work applies X-ray grating interferometry to the study of …

Development Of A Sonically Powered Biodegradable Nanogenerator For Bone Regeneration, Avi S. Patel

University Scholar Projects

Background: Reconstruction of bone fractures and defects remains a big challenge in orthopedic surgery. While regenerative engineering has advanced the field greatly using a combination of biomaterial scaffolds and stem cells, one matter of difficulty is inducing osteogenesis in these cells. Recent works have shown electricity’s ability to promote osteogenesis in stem cell lines when seeded in bone scaffolds; however, typical electrical stimulators are either (a) externally housed and require overcomplex percutaneous wires be connected to the implanted scaffold or (b) implanted non-degradable devices which contain toxic batteries and require invasive removal surgeries.

Objective: Here, we establish a biodegradable, piezoelectric …

Development Of A Sonically Powered Biodegradable Nanogenerator For Bone Regeneration, Avi Patel

Honors Scholar Theses

Background: Reconstruction of bone fractures and defects remains a big challenge in orthopedic surgery. While regenerative engineering has advanced the field greatly using a combination of biomaterial scaffolds and stem cells, one matter of difficulty is inducing osteogenesis in these cells. Recent works have shown electricity’s ability to promote osteogenesis in stem cell lines when seeded in bone scaffolds; however, typical electrical stimulators are either (a) externally housed and require overcomplex percutaneous wires be connected to the implanted scaffold or (b) implanted non-degradable devices which contain toxic batteries and require invasive removal surgeries.

Objective: Here, we establish a biodegradable, piezoelectric …

Methods To Remotely Eliminate Biofilm From Medical Implants Using 2.4 Ghz Microwaves, Brett Glenn

Mechanical Engineering Undergraduate Honors Theses

Infections associated with biofilm growth are usually challenging to eradicate due to their high tolerance toward antibiotics [11, 12]. Biofilms often form on the inert surfaces of medically implanted devices [13]. No matter the sophistication, microbial infections can develop on all medical devices and tissue engineering constructs [12]. Related infections lead to 2 million cases annually in the U.S., costing the healthcare system over $5 billion in additional healthcare expenses [12].

Novel solutions to biofilm’s microbial colonization span the spectrum of engineering and science disciplines. Yet a practical solution still does not exist. The research presented here will explore a …

Modelling Palladium Decorated Graphene Using Density Functional Theory To Analyze Hydrogen Sensing Application, Sameer Kulkarni

Mechanical Engineering Undergraduate Honors Theses

Graphene is an exciting new material with many promising applications. One such application of graphene is gas sensing, when adsorbed with transition metals, notably Palladium. Therefore, it is of paramount importance to have appropriate ab initio calculations to calculate the various properties of graphene under different adsorbates and gasses. The first step in these calculations is to have a functioning base Density Functional Theory (DFT) model of pristine graphene decorated with Palladium. The computational methods described in this paper has yielded results for pristine graphene that have been confirmed many times in previous experimental and theoretical studies. Future work needs …

Additive Manufacturing Of High Performance Flexible Thermoelectric Generators Using Nanoparticle Inks, Tony Valayil Varghese

Boise State University Theses and Dissertations

Flexible thermoelectric devices are attractive power sources for the growing demand of flexible electronics and sensors. Thermoelectric generators have an advantage due to no moving parts, silent operation and constant power production with a thermal gradient.

Conventional thermoelectric devices are rigid and fabricated using complex and relatively costly manufacturing processes, presenting a barrier to increase the market share of this technology. To overcome such barriers, this work focuses on developing near ambient-temperature flexible thermoelectric generators using relatively low-cost additive manufacturing processes. A screen printable ink was developed for transforming nanoparticle ink into high-performance flexible thermoelectric generators with a peak thermoelectric …

A Study On Ultrasonic Energy Assisted Metal Processing : Its Correeltion With Microstructure And Properties, And Its Application To Additive Manufacturing., Anagh Deshpande

Electronic Theses and Dissertations

Additive manufacturing or 3d printing is the process of constructing a 3-dimensional object layer-by-layer. This additive approach to manufacturing has enabled fabrication of complex components directly from a computer model (or a CAD model). The process has now matured from its earlier version of being a rapid prototyping tool to a technology that can fabricate service-ready components. Development of low-cost polymer additive manufacturing printers enabled by open source Fused Deposition Modeling (FDM) printers and printers of other technologies like SLA and binder jetting has made polymer additive manufacturing accessible and affordable. But the metal additive manufacturing technologies are still expensive …

Comparison Of Organic Food Packaging In Denmark, Finland, Germany, Great Britain And Italy, Sara Paunonen, Marja Pitkänen, Mika Vähä-Nissi, Ville Leminen, Mika Kainusalmi

Journal of Applied Packaging Research

The objective of this study was to provide a snapshot of organic food assortments in supermarkets in Denmark, Finland, Germany, Great Britain, and Italy, and compare the packages used for five organic food products (eggs, meat, fish, mushrooms, berries). In addition, a comparison was made between packaging for regular and organic whole eggs. The highest number of organic products was found in the Danish supermarket. The main difference between the countries was in the use of national organic logos. Of the different food products, egg cartons had the most variation in materials and visual design. In all countries the product …