Materials Science and Engineering Commons^™

Effect Of Dissolved Oxygen On Corrosion Of Carbon And 13cr Steel In A Brine Environment, Kevin Peter Iu, Andy Zhou

Materials Engineering

Oxygen corrosion is a major threat to seawater injection systems that are part of offshore drilling operations. Seawater is typically deoxygenated to an industry standard of(DO) by injection through a deaeration column followed by treatment with oxygen scavenging chemicals. Commercial simulation software like OLI Studio: Corrosion Analyzer predicts high corrosion rates when injection seawater contains high DO levels, justifying deoxygenation. However, a notable lack of experimental data exists concerning the effect of varying levels of dissolved oxygen on corrosion rate. The goal of this project is to measure the effect of three dissolved oxygen levels (0, 62, and 620 ppb) …

Pressure Driven Desalination Membranes: Lyotropic Liquid Crystals Containing Single Walled Carbon, Matteo A. Del Giudice, Samantha Castillo Merigold

Materials Engineering

This project presents a potential alternative desalination technique that utilizes the ion rejection properties of single walled carbon nanotubes dispersed in a lyotropic liquid crystal (LLC) matrix. Previous research has pointed to the polymerizable surfactant methacryloxy ethyl hexadecyl dimethyl ammonium bromide (C16MA) having capabilities of filtering molecular components smaller than a nanometer, when oriented in cylindrical micelles. SWCNTs were dispersed in deionized water by probe sonication and addition of surfactant cetyltrimethylammonium bromide (CTAB) due to SWCNTs’ hydrophobic properties. Membranes were produced containing 55wt% C16MA, 37wt% DI water, 0.1wt% with respect to the monomer (WRM) SWCNTs, 1.9 wt% WRM 2,2-dimethoxy-2-phenylacetophenone (photointiator), …

Novel And Fast Peridynamic Models For Material Degradation And Failure, Siavash Jafarzadeh

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Fracture is one of the main mechanisms of structural failure. Corroded surfaces with chemically-induced damage are, notably, potential sites for crack initiation and propagation in metals, which can lead to catastrophic failure of structures. Despite some progress in simulating fracture and damage using classical models, realistic prediction of complex damage progression and failure has been out of reach for many decades. Peridynamics (PD), a nonlocal theory introduced in 2000, opened up new avenues in modeling material degradation and failure. Existing numerical methods used to discretize PD equations, however, are quite expensive as the PD nonlocal interactions make them unaffordable for …

Sound, Material And Strength Correlation, Ryan Mcbride

Symposium of Student Scholars

With a growing amount of manufacturing utilizing 3D printing, there is a correlation between strength and material which can affect sound produced by sirens. An air raid siren that has been downloaded from Thingiverse.com spins with a 49:1 gear ratio to produce 2 tone sounds and with that large number of revolutions comes friction, and in order to create a 3D printed air raid siren, the siren must be made out of a material that can withstand high temperatures without melting and quick rotations without delaminating. There are many materials that can be printed to withstand those forces, but it …

Computational Design Of Nonlinear Stress-Strain Of Isotropic Materials, Askhad M.Polatov, Akhmat M. Ikramov, Daniyarbek Razmukhamedov

Chemical Technology, Control and Management

The article deals with the problems of numerical modeling of nonlinear physical processes of the stress-strain state of structural elements. An elastoplastic medium of a homogeneous solid material is investigated. The results of computational experiments on the study of the process of physically nonlinear deformation of isotropic elements of three-dimensional structures with a system of one- and double-periodic spherical cavities under uniaxial compression are presented. The influence and mutual influence of stress concentrators in the form of spherical cavities, vertically located two cavities and a horizontally located system of two cavities on the deformation of the structure are investigated. Numerical …

Exploration Of The Sludge Biodiesel Pathway, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Wastewater sludge is an overlooked source of fat, oil, and grease (FOG) that could be converted into biodiesel. The United States produces about 8 million tons of sludge per year. The disposal cost for this amount of sludge is about 2 billion US dollars. The widespread availability and low cost of sludge compared to other biodiesel raw materials make it an economical choice for a renewable fuel. Using sludge as a raw material can produce 25 to 30 mg per gram of fatty acid methyl ester (FAME); the main component of biodiesel. Sludge biodiesel has the potential of transforming a …

Voltage-Controlled Magnetic Anisotropy In Antiferromagnetic Mgo-Capped Mnpt Films, P. H. Chang, Wuzhang Fang, T. Ozaki, Kirill Belashchenko

Kirill Belashchenko Publications

The magnetic anisotropy in MgO-capped MnPt films and its voltage control are studied using first-principles calculations. Sharp variation of the magnetic anisotropy with film thickness, especially in the Pt-terminated film, suggests that it may be widely tuned by adjusting the film thickness. In thick films the linear voltage control coefficient is as large as 1.5 and -0.6 pJ/Vm for Pt-terminated and Mn-terminated interfaces, respectively. The combination of a widely tunable magnetic anisotropy energy and a large voltage-control coefficient suggest that MgO-capped MnPt films can serve as a versatile platform for magnetic memory and antiferromagnonic applications.

Comparison Of Tensile Properties Of Triaxial Braided Carbon Fiber Composites Made From Vacuum Assisted Resin Transfer Molding (Vartm) And Autoclave Molding, Donald A. Klosterman, Charles Browning

Chemical and Materials Engineering Faculty Publications

Triaxially braided fiber composites are increasingly being used in aerospace, ballistic, and sporting good applications due to their inherent damage tolerance, torsional stability, and cost compared to woven fabrics and unidirectional preforms. There have been numerous publications over the past 15-20 years on the mechanical properties and failure mechanisms of triaxial braided composites. However, most of these have involved panels made with autoclave curing. In the present study, braided carbon fiber composites were made using autoclave curing and vacuum assisted resin transfer molding (VARTM). The goal of the study was to compare the physical and tensile properties of quasi-isotropic panels …

Husky Hand: A Low-Cost Electro-Mechanical Prosthetic Arm For The Underprivileged, Adam Robert

Thinking Matters Symposium

A continuation of a low-cost prosthetic upper limb prototype design which was investigated in EGN 301. The prosthetic is specifically designed for the needs and requirements of under privileged individuals in the Dominican Republic with upper limb amputations. The project focuses on the creation of an open-source computer aided prosthetic hand/arm model. The design allows consumer-grade fused filament fabrication (FFF) 3-D printers to be used. The improved design allows for the integration of the PQ-12 linear actuator for grasp and finger control. This simplifies the assembly, while, also reducing the size and mass of the whole unit. Producing a low-cost …

Detection And Aggregation Of Listeria Monocytogenes Using Polyclonal Antibody Gold-Coated Magnetic Nanoshells Surface-Enhanced Raman Spectroscopy Substrates, Robert T. Busch, Farzia Karim, Yvonne Sun, H. Christopher Fry, Yuzi Liu, Chenglong Zhao, Erick S. Vasquez

Chemical and Materials Engineering Faculty Publications

Magnetic nanoshells with tailored surface chemistry can enhance bacterial detection and separation technologies. This work demonstrated a simple technique to detect, capture, and aggregate bacteria with the aid of end-functionalized polyclonal antibody gold-coated magnetic nanoshells (pAb-Lis-AuMNs) as surface-enhanced Raman spectroscopy (SERS) probes. Listeria monocytogenes were used as the pathogenic bacteria and the pAb-Lis-AuMNs, 300 nm diameter, were used as probes allowing facile magnetic separation and aggregation. An optimized covalent bioconjugation procedure between the magnetic nanoshells and the polyclonal antibody was performed at pH six via a carbodiimide crosslinking reaction. Spectroscopic and morphological characterization techniques confirmed the fabrication of stable pAb-Lis-AuMNs. …

Solid State Synthesis And Characterization Of Apatite Based Ceramic Waste Form For The Immobilization Of Radioactive Iodine, Md Imdadul Islam

LSU Doctoral Dissertations

The growing demand for nuclear power in the United States and worldwide is accountable for addressing the major concern of radioactive waste, involving the technical challenges of maintaining the nuclear fuel cycle and immobilizing high-level wastes for safe disposal in geological storage. The appropriate selection of waste forms for spent nuclear fuel such as fission products and radionuclides can be effective means for a feasible and sustainable nuclear fuel cycle. But highly volatile radionuclides such as iodine (129) are of specific concern due to its extraordinary long half-life (15.7 million years). Due to its poor solubility and high volatility at …

Fabrication And Characterization Of Electrospun Poly(Acrylonitrile-Co-Methyl Acrylate)/Lignin Nanofibers: Effects Of Lignin Type And Total Polymer Concentration, Suchitha Devadas, Saja M. Nabat Al-Ajrash, Donald A. Klosterman, Kenya A. Crosson, Garry S. Crosson, Erick S. Vasquez

Chemical and Materials Engineering Faculty Publications

Lignin macromolecules are potential precursor materials for producing electrospun nanofibers for composite applications. However, little is known about the effect of lignin type and blend ratios with synthetic polymers. This study analyzed blends of poly(acrylonitrile-co-methyl acrylate) (PAN-MA) with two types of commercially available lignin, low sulfonate (LSL) and alkali, kraft lignin (AL), in DMF solvent. The electrospinning and polymer blend solution conditions were optimized to produce thermally stable, smooth lignin-based nanofibers with total polymer content of up to 20 wt % in solution and a 50/50 blend weight ratio. Microscopy studies revealed that AL blends possess good solubility, miscibility, and …

Magnetically Induced Demulsification Of Water And Castor Oil Dispersions Stabilized By Fe3o4-Coated Cellulose Nanocrystals, Mohammad J. Hasan, Frankie A. Petrie, Ashley E. Johnson, Joshua Peltan, Meredith Gannon, Robert T. Busch, Serhiy O. Leontsev, Erick S. Vasquez, Esteban E. Ureña-Benavides

Chemical and Materials Engineering Faculty Publications

Superparamagnetic iron oxide (Fe3O4) nanoparticle (NP) coated cellulose nanocrystals (CNCs) were synthesized and used to prepare emulsions with magnetically controlled stability. Magnetite NPs were deposited onto the surface of wood pulp CNCs (WCNCs) and bacterial CNCs (BCNCs) by a one-step coprecipitation method. The effect of the CNC to Fe3O4 mass ratio (1:1, 1:2, and 1:4) was varied to optimize the colloidal, magnetic and emulsifying properties of the hybrid NPs. TEM images showed that the 1:4 ratios lead to greater coverage of Fe3O4 than lower Fe3O4 loadings (1:1, and 1:2). The CNCs and Fe3O4 appeared to interact via hydrogen bonding between …

Jcati Carbon Fiber Recycling Shredder, Benjamin Cooley

All Undergraduate Projects

Once carbon fibers are cast into a resin and used in a composite material, retrieving those fibers can be a difficult task. However, it is beneficial to recycle and reuse the fibers from old unneeded components rather than pay the cost of acquiring new ones. The Joint Center for Aerospace Technology Innovation (JCATI) carbon fiber recycling device condenses the multistep process of extracting the fibers by integrating all steps into one automated device. In the previous version of the device, the cutting blades turned the long composite strips into thin fingers but did not sever them across the width.

The …

Observation Of New Particle Formation In The Northern Hemisphere At Altitude From 4 To 20 Km, Mohamed Saad

Electronic Theses and Dissertations

New particle formation (NPF) is investigated using measurements of aerosol size distributions and meteorological variables made in two continents, including USA and Europe. Despite the considerably different aerosol particle abundances among the sites, a common relationship was found between the characteristics of NPF events and the air mass convective and/or advective transport. CO and O3 act as tracers of tropospheric and stratospheric air, respectively, their statistical relationship can be used to quantify air mass characteristics and origins. The mixing ratio values of CO increased within the upper troposphere layer before/during NPF events, which may serve as an indicator of occurring …

Recycling Of Fiber Polymer Matrix Composites In Cementitious Materials, Edward Patton Clark

Electronic Theses and Dissertations

Recycling options for fiber polymer matrix composite waste materials are limited because they typically cannot be reused, reprocessed for down-cycling, and are generally environmentally unfriendly. The utility industry, specifically electrical distribution, has been increasingly using hybrid carbon, glass fiber, and epoxy resin composite rods for high-voltage (HV) conductor transmission lines. The high-voltage conductor core (HVCC) used in the transmission line can have an optimal in-service-life of roughly several decades, in which the material is then retired to a waste landfill. Currently, there is limited research and recycling methodology for these hybrid composite rods. In this research, powder carbon fiber, glass …

Monitoring Of Overhead Polymer Core Composite Conductors Under Excessive Mechanical Loads Using Fiber Bragg Grating Sensors, Daniel H. Waters

Electronic Theses and Dissertations

This combined experimental and numerical study addresses mechanical effects associated with static and dynamic loading of novel High Temperature Low Sag (HTLS) transmission line polymer core composite conductors. The developed methodology was successfully applied to ACCC® to explain the complex failure mechanisms associated with combined bending and tension loading. Furthermore, the use of Fiber Bragg Grating (FBG) sensors was investigated for the first time to monitor the ACCC® design during installation and in-service.

Transverse low-velocity impacts to the ACCC® conductor having either free or constrained end conditions and large axial tensile loads were performed. It was identified that the most …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Molecular To Macroscopic Understanding Of Chloroaluminate Anion Intercalation In Rechargeable Aluminum-Graphite Batteries, Jeffrey Xu

Dissertations and Theses

Today’s global energy challenges pose an urgent need to electrify transportation and better store intermittent renewable energy sources (e.g., solar and wind energy). For such large-scale battery applications, aluminum batteries are a promising “beyond lithium-ion” technology due to the high volumetric capacity, earth abundance, low-cost, and inherent safety of aluminum metal. However, there are very few compatible positive electrode materials that exhibit high energy density and cycling stability, in part due to the challenges of electrochemically intercalating highly charged Al³⁺ cations. Recently, graphite has been demonstrated as a promising positive electrode material in non-aqueous rechargeable aluminum batteries, which store …

The Development Of A Holistic Quality Score Using In-Situ Monitoring Of Laser Powder Bed Fusion, Ryan Daigneault

College of Graduate Studies: Theses & Dissertations

Additive manufacturing processes allow for a great degree of flexibility in terms of part production. The process is autonomous once the part has started printing in that the operator generally does not need to intervene until the part is finished. One issue that this introduces, however, is an inability to determine part quality during the printing process. Once a part has started printing, the operator must either wait until the part is finished or regularly check on the part during the print to determine the part quality. Using data gathered from multiple sensors, a quality score can be used to …

Continuous Preparation And Application Of Novel Heterogeneous Catalysis, Michael B. Burkholder

Theses and Dissertations

Transition metal heterogeneous catalysts are widely used across many chemical industries to reduce waste and emissions and reduce production time while increasing rate. The prevalence of these materials results from the complex relationship between metal nanoparticles and supports affecting final catalytic performance. Rational catalyst synthesis describes the ability to precisely engineer structures through controlled preparation. Novel materials and continuous processing represent a promising approach for rational catalyst synthesis.

The application of these catalysts in continuous, multiphase processes, such as cross-coupling reactions, oxidation chemistry, and nitroreduction processes, are paramount to developing new commercial routes for high-value products. Pd/G catalysts synthesized by …

Surface Characterization Of Accident Tolerant Fuel Claddings Candidates After Prolonged Exposure To Steam Oxidation, Connor F. Donlan

Theses and Dissertations

Accident Tolerant Fuel Claddings are designed to improve fuel performance and safety in abnormal reactor conditions. The development of these cladding materials has become a top priority for the nuclear community, with incidents such as the Three Mile Island accident and the Fukashima Dai-chi accident. The development of these claddings has resulted in 2 subsections: coating current claddings or replacing cladding materials with new materials. The claddings studied in this thesis are a Zircaloy-4 cladding coated with chromium through physical vapor deposition, Zircaloy-4, and a FeCrAl alloy, C26M. This thesis assessed the surface chemistry, roughness, and wettability after extended exposure …

Biomass-Derived Electrode Materials And Sustainable Processes For Supercapacitors, Katelyn M. Shell

Theses and Dissertations

Biomass is one of the most abundant natural resources and has been used as a source of energy for thousands of years. Biomass as a precursor for energy storage materials is still relatively novel and faces several obstacles before becoming commonly used in today’s electrical devices. Currently, energy storage devices, such as batteries, capacitors, and supercapacitors, utilize petroleum-derived graphitic carbons for anodes, generating a need for more sustainable materials. Biomass, as a carbon-rich source for electrode materials, presents a viable and economically feasible alternative due to the prevalent lignocellulosic compounds: lignin, cellulose, and hemicellulose. Preliminary studies on the solid residues …

Perovskite Thin Films Annealed In Supercritical Fluids For Efficient Solar Cells, Gilbert Annohene

Theses and Dissertations

In the field of photovoltaics, scientists and researchers are working fervently to produce a combination of efficient, stable, low cost and scalable devices. Methylammonium lead trihalide perovskite has attracted intense interest due to its high photovoltaic performance, low cost, and ease of manufacture. Their high absorption coefficient, tunable bandgap, low-temperature processing, and abundant elemental constituent provide innumerable advantages over other thin film absorber materials. Since the perovskite film is the most important in the device, morphology, crystallization, compositional and interface engineering have been explored to boost its performance and stability. High temperatures necessary for crystallization of organic-inorganic hybrid perovskite films …

Accident Tolerant Fuels Claddings And The Evolution Of Their Surface Characteristics Under Critical Heat Flux, Rajnikant V. Umretiya

Theses and Dissertations

Enhanced Accident Tolerant Fuels (ATFs) systems for light water reactors require higher temperature oxidation resistance in steam environments than the current UO₂ – zirconium fuel system. Investigating the ATF materials’ surface properties is needed as they have evidenced to affect the Critical Heat Flux (CHF), which is an important parameter of the thermal-hydraulic performance required to provide safety margins. In this dissertation, the surface properties of FeCrAl alloys (APMT and C26M), Zircaloy-2, Zircaloy-4, and Cr-coating on Zircaloy-4 substrates produced by Physical Vapor Deposition (PVD) and Cold Spray (CS) were investigated according to their chemistry, topography, and wettability. The static …

Impact Dynamics Of Surfactant-Laden Droplets On Non-Wettable Coatings, Amir Esmaeili

Theses and Dissertations

Owing to their excellent water repellency, non-wettable (superhydrophobic) coatings have gained tremendous attention in the past couple of decades. Alkyl ketene dimer (AKD), an inexpensive polymer frequently used in paper industry as a sizing agent, has shown potentials to become superhydrophobic. The formation of a porous structure after curing the solidified AKD for an extra-long time (4–6 days) results in superhydrophobicity, i.e., a static contact angle with water of >150° and a roll-off angle of <10°. In this work, a facile and low-cost method was used to turn the surface of AKD superhydrophobic in a very short period of time by briefly treating the coatings, obtained from isothermally heated molten AKD at 40 °C for 3 min, with ethanol. The resulting superhydrophobicity is due to the formation of porous, entangled irregular micro/nano textures that create air cushions on the surface leading to droplet state transition from Wenzel to Cassie. As a proof of concept, the same material was applied to the co-sputtered nickel-tungsten thin films, commonly used in micro/nano-electro-mechanical systems, to improve their hydrophobicity. According to the results, at least 20% increase was observed in the dynamic contact angles of the treated substrates.

In addition, this work presents a detailed high-speed imaging analysis of the influence of the molecular weight, concentration and ionic nature of surfactants on droplet …

Development Of Synthetic Coal Char Simulant For Microwave Conversion Studies: A Computationally-Driven Approach, Kevin A. Hager

Graduate Theses, Dissertations, and Problem Reports (ETD)

Recent experimental demonstration of new reaction windows for coal char/methane reactions that are less energy-intensive, provides innovation for modular reactors. However, the correlation of the exact mechanism for the enhancement of these reaction windows is not certain. This study investigates the simplification of these experimental studies by developing a well-characterized coal char simulant. The approach involves using a computational approach to screen macroscopic composition to replicate the dielectric and compositional response of actual char. This study is focused on PRB coal char. A discrete element method (DEM) technique was used to simulate the packing of coal chars to give the …

Metal Supported Solid Oxide Fuel Cell Using Proton Conducting Electrolyte For Direct Ammonia Utilization, Edwin Vega Hiraldo

Graduate Theses, Dissertations, and Problem Reports (ETD)

Transportation represents about 27% of global warming greenhouse gas emissions nowadays. To reduce these emissions, fuel cell electric vehicles have been poised to be a new trend to provide zero-emission transportation. Among them, solid oxide fuel cells (SOFCs) offer efficient, clean energy, especially when powered by carbon-free fuel, such as ammonia. To enable onboard ammonia-fed SOFCs, a metal-supported, proton-conducting SOFC is investigated in this study. The metal support would provide physical robustness for thermal shock during vehicles’ quick start-up and shutdown, reduce internal temperature gradients due to the greater thermal conductivity of the metal, and enable conventional metal joining for …

Atmospheric Corrosion Of Galvanically Coupled Aluminum Alloys And Carbon Steel, Mitchell Felde

Williams Honors College, Honors Research Projects

Aluminum alloys are a steadily growing material being commonly used in lieu of typical steels. Additional alloying, heat treatment, and other property enhancing processes are expanding the use of these alloys. However, with this expansion, galvanic corrosion is becoming more of an issue in the design stage due to the combination of these alloys with steels. The automotive industry is one industry where the use of aluminum alloys is becoming common practice. Aluminum alloys provide a lightweight aspect over the conventional carbon steel that was used previously. As a result of this transition towards more lightweight materials, galvanic coupling is …

Testing The Effectiveness Of Various Fabrics For Use In Protective Face Coverings, Isaac Daley

Williams Honors College, Honors Research Projects

Facemask requirements have been heavily implemented as a result of the COVID-19 pandemic. The purpose of this study was to test various fabrics that could be used in face coverings and determine which materials are best for reducing virus transmission rates. Of the seven fabrics tested, five were conventional home-use fabrics and the other two were surfaces modified with hydrophobic organosilanes. Wettability and droplet adherence tests were performed on each material. The materials that performed the best were decyltrichlorosilane (DTS) modified cotton, perfluorotrichlorosilane (FTS) modified cotton, and polyester. Contact angles for water droplets on these fabrics were 106°, 93°, and …