Materials Science and Engineering Commons^™

Electrochemical Impedance Spectroscopy Analysis Of Corrosion Of Reinforcing Steel In Fly Ash Mortar By Means Of Transmission Line Modeling, Padraig Stack

Williams Honors College, Honors Research Projects

Electrochemical impedance spectroscopy (EIS) is an important non-destructive tool that allows for a deeper understanding of the electrochemical processes and mechanisms occurring in an electrochemical cell. Equivalent electrical circuits (EECs) are used to model the impedance data into electrical components, such as resistors and capacitors, on a circuit. Current potentiostat offers software packages that can analyze the frequency response, but the software only supports “simple” EEC that can be written as fixed electrical components in some combination of series and parallel. Park and Macdonald propose a transmission line model (TLM) that does not use lumped-element models, instead, the values of …

Electrochemical Chloride Removal, Marcus Yudt

Williams Honors College, Honors Research Projects

Electrochemical chloride removal (ECR) was tested to see its effectiveness in preventing corrosion on rebar samples within 3.5 wt% sodium chloride concrete. In order to do this, three scenarios were evaluated using electrochemical techniques such as cyclic potentiodynamic polarization and electrochemical impedance spectrsoscopy as well as visual inspections. The three scenarios that were evaluated were one with no chlorides present within the concrete, one that was a worst-case scenario where extreme pitting and corrosion were initiated, and one that had chlorides present and received the ECR treatment. Cyclic polarization curves showed that the ECR and reference without chlorides had similar …

Rational Design Of Metal-Organic Frameworks (Mofs)-Based Functional Materials Towards Better Air Quality, Zan Zhu

Theses and Dissertations

Air pollution is a major threat to environmental safety and public health. Volatile organic compounds (VOCs), particulate matter (PM), and airborne microorganisms are three typical air pollutants. Conventional strategies to prevent and mitigate air pollution have been employed, which, however, are generally passive. For instance, VOC sensing through solid-state devices is a conventional approach, which, however, is not capable of capturing and removing VOCs. On the other hand, air filters and face masks are useful equipment to protect people from inhaling PM and airborne microorganisms. But most commercial filters can only capture them on the surfaces, which may cause secondary …

Branched Chain Amino Acid Strain State Monitoring With Raman Spectroscopy And Plasmonic Bowtie Nanoantenna Devices For Early Disease Detection, Caroline A. Campbell

Theses and Dissertations

This work centers on the development and the down-selection of nano-manufactured devices to be used in conjunction with Raman spectroscopy for probing a branched chain amino acid. The nano-manufactured devices integrate plasmonic nanoantennas for the purpose of amplifying molecular fingerprints, which are otherwise difficult to detect, through Surface Enhanced Raman Spectroscopy (SERS). Plasmonic nanostructures can be utilized for a variety of biomedical and biochemical applications to detect the characteristic fingerprint provided by Raman Spectroscopy. The nano-manufactured devices create an electric field that amplifies minute perturbations and raises the signal above background noise. This may provide a deeper understanding of signal …

Effects Of Additive Manufacturing Techniques On The Magnetocaloric Properties And Chemical Stability Of Lafexcoysi13-X-Y Alloys, Binyam Wodajo

Theses and Dissertations

Additive manufacturing (AM) is an emerging process to fabricate net shape, intricate, engineering components with minimal material waste; however, traditionally it has been largely applied to structural materials. AM of functional materials, such as magnetic materials, has received much less attention and the field is still in its infancy. To date, AM of magnetocaloric regenerators for magnetic refrigeration (an energy-efficient alternative to the conventional vapor-compression cooling technology), remains a challenge. There are several magnetic refrigerator device designs in existence today that are predicted to be highly energy-efficient, on condition that suitable working materials can be developed. This challenge in manufacturing …

Synthesis Of Novel Nio/Comn2o4 Heterostructured Nanoparticles And The Effects Of Variable Size And Metal Concentrations On Their Magnetic And Surface Chemical Properties, Farhan Ishrak

Graduate Theses/Dissertations

I studied the effect of core size and metal concentration on the structural, morphological, and magnetic properties of NiO-based magnetic heterostructured nanocrystals (HNCs) generated hydrothermally. The NiO nanocrystals were created by a thermal decomposition technique, while the surrounding Mn and Co-based phases were created through a hydrothermal procedure, with core diameters ranging from 9.31 nm to 24.51 nm and total metal concentrations of 0.05 M and 0.08 M. The resulting inverted AFM-FiM NiO/CoMn2O4 bimagnetic systems make up the heterostructured nanocrystals. The magnetic HNCs were thoroughly characterized using XRD, SEM-EDX, TEM, PPMS magnetometry, and XPS analysis. Investigations into the structure of …

On The Synthesis And Characterization Of Bimagnetic Coo/Nife2o4 Heterostructured Nanoparticles, Muhammad Sharif Uddin

Graduate Theses/Dissertations

Bimagnetic nanoparticles show promise for applications in energy efficient magnetic storage media and magnetic device applications. The magnetic properties, including the exchange bias of nanostructured materials can be tuned by variation of the size, composition, and morphology of the core vs overlayer of the nanoparticles (NPs). The purpose of this study is to investigate the optimal synthesis routes, structure and magnetic properties of novel CoO/NiFe2O4 heterostructured nanocrystals (HNCs). In this work, I aim to examine how the size impacts the exchange bias, coercivity and other magnetic properties of the CoO/NiFe2O4 HNCs. The nanoparticles with sizes ranging from 10 nm to …

Improving Manufacturing Processes For Making Lithium Ion Battery Electrodes, Ming Wang

Theses and Dissertations--Chemical and Materials Engineering

Rechargeable lithium-ion batteries (LIBs) are widely used to provide energy and power in portable electronics, electric vehicles, and energy storage systems. The LIB market has grown dramatically as they have a combination of high energy density, high power density, proven reliability, and long cycle life. The manufacturing process is one of the key factors as it strongly affects the cost and performance of LIBs.

This dissertation is focused firstly on the development of a conventional slurry-based electrode manufacturing process. Slurry making is a critical step that affects the subsequent steps in battery manufacturing. In this work, we have investigated the …

Implementation Of Multiscale Mechanisms In Finite Element Analysis Of Active Composite Structures, Amany G. Micheal Prof., Yehia Bahei-El-Din

Mechanical Engineering

Interrogation of composite structures for inherent damage is investigated implementing three-tier analysis scheme. The analysis starts at the structure level where a general-purpose Finite Element code ABAQUS is employed to obtain the stress field in the second level of analysis that is the composite laminate. A special material routine is prepared to propagate the local fields to the individual plies and hence to the third level of analysis which is the microstructure modelling of the composite. Through the third level of analysis, interface damage between fiber and matrix is checked implementing a certain failure criteria. The interaction between the different …

Modeling, Fabrication, And Characterization Of Rf-Based Passive Wireless Sensors Composed Of Refractory Semiconducting Ceramics For High Temperature Applications, Kavin Sivaneri Varadharajan Idhaiam

Graduate Theses, Dissertations, and Problem Reports (ETD)

Real-time health monitoring of high temperature systems (>500^oC) in harsh environments is necessary to prevent catastrophic events caused by structural failures, varying pressure, and chemical reactions. Conventional solid-state temperature sensors such as resistance temperature detectors (RTDs) and thermocouples are restricted by their operating environments, sensor dimensions and often require external power sources for their operation. The current work presents the research and development of RF-based passive wireless sensing technology targeting high temperatures and harsh environmental conditions. Passive wireless devices are generally classified as near-field and far-field devices based on the interrogation distance. Near-field sensors are placed at …

Microwave-Assisted Carbon Nanotube Growth From Methane On Surface Catalyst Exsolving Perovskite Oxide, Angela M. Deibel

Graduate Theses, Dissertations, and Problem Reports (ETD)

The novel method of using a perovskite exsolution catalyst, strontium titanium nickel oxide (STNO), proved capable of simultaneously producing carbon nanotubes (CNTs) and CO_x-free hydrogen during methane decomposition under microwave irradiation. An optimization of common perovskite materials was conducted for microwave-responsiveness with the results reported in this study. Out of the materials screened, strontium titanium nickel oxide (STNO) was the best candidate to achieve an acceptable methane conversion rate as well as a decent responsiveness to microwave. STNO was further optimized through Ni content, reduction dwell time, and reduction temperature to produce the best methane conversion and CNT …

Low-Temperature Hot Corrosion Of Boilers In The Coal-Fired Power Plant, Artem Gavrilev

Graduate Theses, Dissertations, and Problem Reports (ETD)

Hot corrosion of materials has remained a relevant topic since its introduction in the second half of the 20th century as gas turbine engines suffered severe corrosion during operation over seawater. Hot corrosion is observed in a multitude of high temperature components, such as gas turbines, power plants, refineries, fluidized bed combustion systems, pipelines, and industrial waste incinerators.

Hot corrosion experiments in the laboratory have been conducted under constant temperatures of interest, while in the actual working conditions of coal-fired power plants, boiler tubes are cooled down via water cooling from a relatively high fireside temperature, e.g., 1000°C. To investigate …

Magnetic Field Penetration Technique To Study Field Shielding Of Multilayered Superconductors, Iresha Harshani Senevirathne, Alex Gurevich, Jean R. Delayen, A-M Valente-Feliciano

Physics Faculty Publications

The SIS structure which consists of alternative thin layers of superconductors and insulators on a bulk niobium has been proposed to shield niobium cavity surface from high magnetic field and hence increase the accelerating gradient. The study of the behavior of multilayer superconductors in an external magnetic field is essential to optimize their SRF performance. In this work we report the development of a simple and efficient technique to measure penetration of magnetic field into bulk, thin film and multilayer superconductors. Experimental setup contains a small superconducting solenoid which can produce a parallel surface magnetic field up to 0.5 T …

Crystalline Analysis Of Geomicrobially-Induced Calcium Carbonate Precipitation In Sands Using A Surface Percolation Treatment Technique, Justin Edward Mulloney

UNF Graduate Theses and Dissertations

Ottawa 50/70 sand specimens and natural beach sand samples were treated using bio-augmented geomicrobies via a surface percolation technique. Testing was conducted on these specimens to determine how resultant calcium carbonate precipitation changed as a function of temperature, depth from the surface, and in the presence of magnesium. Specifically, x-ray Diffraction (XRD), a Scanning Electron Microscope (SEM), and Energy Dispersive X-ray Spectroscopy (EDS) were used to determine and quantify the presence of calcium carbonate and its associated phase. Results showed a direct relationship between temperature and precipitated calcium carbonate. In addition, as an unintended consequence associated with the treatment, ammonium …

Simulation And Fabrication Of All Oxide-Based Ito/Tio2/Cuo/Au Heterostructure For Solar Cell Applications, Sajal Islam

Graduate Theses/Dissertations

Oxide heterostructures have drawn great attention lately, due to their environment-friendly properties and potential applications in optoelectronic devices. In this work, a simulation study of a heterojunction solar cell was performed with SCAPS (a solar cell simulator) using TiO2 as an n-type and CuO as a p-type layer. The thickness and the dopant-dependent simulations have shown that the solar cell operates at a maximum efficiency of 19.2% when the thickness of the TiO2/CuO layers is chosen 1.4µm/1.2µm compared to the 11.5% efficiency when FTO is replaced with ITO. An indium-doped tin oxide (ITO) vs fluorine-doped tin oxide (FTO) comparison study …

Growth, Characterization, And Mechanical Testing Of Diamond-Like Carbon Films, Tailei Qi

LSU Master's Theses

The high residual stresses within diamond-like carbon (DLC) films limit its thickness and make the film tend to delaminate from the substrate and be defective on the surface. To address this problem, a new plasma enhanced chemical vapor deposition system (PECVD) was set up to investigate the effects of different film growth parameters on the DLC films, such as chromium doping, gas fluxes, depositing pressures, bias voltages, and depositing times. After the film growth parameters were optimized, this condition was transferred from silicon wafer to SS316 steel plate to deposition of DLC films with some adjustments. Scanning electron microscopy (SEM) …

Entrepreneurially Minded Learning In The Unit Operations Laboratory Through Community Engagement In A Blended Teaching Environment, Erick S. Vasquez, Kelly Bohrer, Abraham Noe-Hays, Arthur Davis, Matthew Dewitt, Michael J. Elsass

Chemical and Materials Engineering Faculty Publications

Online and blended learning opportunities in Chemical Engineering curriculum emerged due to COVID-19. After eight weeks of in-person Unit Operations Laboratory sessions, a remote-learning open-ended final project was assigned to student teams. The assignment involved aspects related to entrepreneurial-minded learning (EML) and community-based learning (CBL). Results show correlations between self-directed learning and the EML framework. Continuous support and involvement of a community partner correlate to students' m

Biodegradable Nanocomposite Multifunctional Packaging Film For Fruits, Kalpani Y. Perera, Shubham Sharma, Dileswar Pradhan, Amit Jaiswal, Swarna Jaiswal

Articles

Biopolymers have been used in food packaging in recent years due to high pollution rates and decreased biodegradation of synthetic polymers. Chitosan (CH) and Sodium alginate (SA) are both biodegradable biopolymers with excellent film forming capability. TiO2 nanoparticles have high mechanical strength, degradation ability and antimicrobial properties, which are beneficial in food packaging. The aim of the current work is to develop the biodegradable multifunctional nanocomposite film for fruit (i.e., Pear) packaging applications. Bionanocomposite film was prepared by solvent casting method using CH-SA and various concentrations of TiO2. The multifunctional properties such as UV barrier, thermal, water retention, mechanical, chemical, …

Atomistic Simulation Of Desalination, Ian David Durr

Symposium of Student Scholars

Atomistic Simulation of Desalination

Ian Durr, Matheus Prates, and Jungkyu Park

Kennesaw State University

In this research, we investigate the desalination capacity of three-dimensional (3D) carbon nanostructures using molecular dynamics simulations. 3D carbon nanostructures proposed here will filter seawater efficiently because of their multiple layers with holes of tunable sizes. The structure is designed to be flexible, allowing mechanical deformation during daily use. The 3D carbon nanostructure will still possess high thermal conductivity, enabling easy recycle through a simple heating process. Here, we employ LAMMPS, Large-scale Atomic/MolecularMassively Parallel Simulator distributed by Sandia National Laboratories to measure salt ion flux through …

Engineering The Surface Of Fe3o4 Nanoparticles For Catalytic And Magnetic Applications, Natalia Da Silva Moura

LSU Doctoral Dissertations

With the rapid depletion of the U.S. energy resources coupled with population growth, heat management technologies must be improved to sustain our quality of life. Precisely, in catalysis, it is estimated that only ~50% of the energy supplied to the reactor is used for product conversion due to dissipation losses. Among the emerging technologies with a promising reduction in heat losses is induction heating, offering targeted heat delivery with magnetic nanoparticles. Under alternating magnetic fields (AMF), these nanoparticles can absorb the energy from Radio-Frequency (RF) fields and dissipate it as heat on the nanoparticle surface. This in situ heat generation …

Analytical Model For Electromagnetic Induction In Pulsating Ferrofluid Pipe Flows, Huiyu Wang, John G. Monroe, Swati Kumari, Serhiy O. Leontsev, Erick S. Vasquez, Scott M. Thompson, Matthew J. Berg, Dibbon Keith Walters, Keisha B. Walters

Chemical and Materials Engineering Faculty Publications

No abstract provided.

Direct Activation Of Light Alkanes To Value-Added Chemicals Using Supported Metal Oxide Catalysts, Md Ashraful Abedin

LSU Doctoral Dissertations

One of the most challenging aspects of modern-day catalysis is the conversion of methane. Direct conversion of methane via dehydroaromatization (MDHA) is a well-known process which can produce valuable hydrocarbons. Mo oxide supported on ZSM-5/MCM-22 has been studied extensively in recent years for MDHA. Mo carbides are responsible for activating methane by forming CHx species. These are dimerized into C2Hy and oligomerized on ZSM-5/MCM-22 Brønsted acid sites to form aromatics. Sulfated zirconia (SZ) supported Mo catalyst contains the acid sites necessary to produce benzene in MDHA. Here, sulfated hafnia (SH), a homologous oxide like SZ, has been proposed to provide …

Mixed Metal Oxide Nanowires Via Solid State Alloying., Veerendra Atla

Electronic Theses and Dissertations

Mixed metal oxide materials with composition control find applications in energy conversion and storage processes such as heterogenous catalysis, photoelectrochemical catalysis, electrocatalysis, thermal catalysis, and lithium-ion batteries. Mixed metal oxides and/or complex oxides with composition control and in one-dimensional form as nanowires could be interesting to various catalysis applications due to control on single crystal surfaces, active sites, acidity versus basicity site density, and oxygen vacancies. The major challenge is to synthesize mixed metal oxide nanowires beyond binary oxides with composition control. In this dissertation, solid state alloying of binary oxide nanowires with solid and liquid precursors is studied to …

Degumming Of Hemp Fibers Using Combined Microwave Energy And Deep Eutectic Solvent, Bulbul Ahmed

LSU Master's Theses

Hemp is considered as one of the sustainable agricultural fiber materials. Degumming or surface modification of hemp bast is needed to produce single fibers for ensuing textile and industrial applications. The traditional degumming process necessitates a high amount of alkali, which causes detrimental environmental pollution. This study offers a new method to degum hemp fibers with reduced use of harmful alkali and precious water resources. In this work, hemp bast fibers were degummed by using combined microwave energy and deep eutectic solvent (DES). The properties of hemp fibers manufactured by this method were investigated and compared with the traditional alkali …

Optimization Of 3d Printed Mold Performance For Injection Molding Via Hollow Infill Patterns, Alan Fong

University Honors Theses

The applicability of hollow infill patterns has been explored for its applications in making 3D printed polymer-based injection molds in the additive manufacturing industry. Hollow infill patterns offer a significant reduction in material costs as well as the opportunity for reducing the cooling times via pumping a coolant fluid through the hollow cavity in a similar fashion to traditional conformal cooling channels. A 3D Jacks Support Hollow mold model was determined to be the best performing design. FEA analysis was conducted to determine the maximum reduction in internal volume (percentage of material saved) that could be achieved without exceeding the …

Facile Fabrication And Characterization Of Kraft Lignin@Fe3o4 Nanocomposites Using Ph Driven Precipitation: Effects On Increasing Lignin Content, Frankie A. Petrie, Justin M. Gorham, Robert T. Busch, Serhiy O. Leontsev, Esteban E. Ureña-Benavides, Erick S. Vasquez

Chemical and Materials Engineering Faculty Publications

This work offers a facile fabrication method for lignin nanocomposites through the assembly of kraft lignin onto magnetic nanoparticles (Fe3O4) based on pH-driven precipitation, without needing organic solvents or lignin functionalization. Kraft lignin@Fe3O4 multicore nanocomposites fabrication proceeded using a simple, pH-driven precipitation technique. An alkaline solution for kraft lignin (pH 12) was rapidly injected into an aqueous-based Fe3O4 nanoparticle colloidal suspension (pH 7) under constant mixing conditions, allowing the fabrication of lignin magnetic nanocomposites. The effects of increasing lignin to initial Fe3O4 mass content (g/g), increasing in ratio from 1:1 to 20:1, are discussed with a complete chemical, structural, and …

Atomistic Thermo-Mechanical Description Of The Deformation Behavior, Scaling Laws, And Constitutive Modeling Of Nanoporous Gold, Mohammed Hassan Yousef Saffarini

LSU Doctoral Dissertations

Metallic foams, or nanoporous (NP) metals as it is widely referred to in literature, with ligament sizes up to a few tens of nm show exceptional mechanical properties such as high strength and stiffness per weight ratio under different loading scenarios due to their high surface area to solid volume ratio. Therefore, they can be utilized in a wide range of applications making them of great interest to researchers. While their elasticity and yield strength have been the subject of several studies, very limited attention was given to the effect of size, strain rate, and temperature on the material plastic …

Experimental Investigation Of The Performance Of A Hybrid Self-Healing System In Porous Asphalt Under Fatigue Loadings, Shi Xu, Liu Xueyan, Amir Tabakovic, Erik Schlangen

Articles

Self-healing asphalt, which is designed to achieve autonomic damage repair in asphalt pavement, offers a great life-extension prospect and therefore not only reduces pavement maintenance costs but also saves energy and reduces CO2 emissions. The combined asphalt self-healing system, incorporating both encapsulated rejuvenator and induction heating, can heal cracks with melted binder and aged binder rejuvenation, and the synergistic effect of the two technologies shows significant advantages in healing efficiency over the single self-healing method. This study explores the fatigue life extension prospect of the combined healing system in porous asphalt. To this aim, porous asphalt (PA) test specimens with …

Life Cycle Assessment Of An Ifixit Pro Tech Toolkit, Camden N. Webb, Dylan A. Ell

Materials Engineering

A life cycle assessment of an iFixit Pro Tech Toolkit was performed to determine the environmental impacts of iFixit’s best-selling toolkit. SimaPro software was used to measure three impact categories: energy usage, water consumption, and global warming potential. This project provides quantitative data on the resources required for repairing devices through use of the toolkit to ultimately reduce the global e-waste stream by re-using electronics. Using the cut-off method, global warming potential of the kit was 4.1 kg of CO₂ equivalents, water consumption was 1.5 m³, and energy usage was 73.9 MJ. Major contributors to these impact …

Dental Cement Thickening Agents For Mudslide Prevention, Kristina Emiliya Babayev, Emily Elizabeth Johnson, Diana Evet Reihaneh

Materials Engineering

The purpose of this project is to develop a non-toxic mud thickening agent for the application of decreasing mudslide intensity where performance is measured by flow rate, viscosity, and toxicity tests. We hypothesized that dental cements could be a potential candidate due to their adhesive, hydrophilic, and biocompatible properties. Zinc phosphate, glass ionomer, and polycarboxylate cement were among the dental cements tested. These tests were performed at low and high concentrations of 25 grams and 125 grams, respectively, mixed into soil to produce 3500 gram samples. The dental cements produced noticeable thickening effects in the mud, as the average viscosity …