Materials Science and Engineering Commons^™

High Energy Density Lithium-Ion Battery Materials., Rachel Dewees

Electronic Theses and Dissertations

Growth of the EV industry has created an increased demand for Li-ion battery electrode materials, and support of a robust lithium-ion battery supply chain is a national imperative. For mainstream acceptance in the American market, the range of EVs must be improved, i.e., the energy density of the battery must be increased. Increasing the specific capacity of the electrode materials is the most direct strategy for increasing the energy density of the battery. Silicon anode materials have a theoretical capacity of over 3700 mAh·g^-1 - an order of magnitude beyond that of the graphitic materials which are currently implemented. …

Toward Electrochemical Detection Of Salmonella Enterica Serovar Enteritidis On Hydroponically Grown Green Onions (Allium Fistulosum L.), Lisseth Casso-Hartmann

All Theses

The Food and Drug Administration (FDA) established standards during the growing, harvesting, packing, and holding of produce for human consumption as part of implementing the Food Safety Modernization Act (FSMA). One of the main requirements for farmers is to detect environmental pathogens such as Salmonella enterica species in water and sprout samples. S. enterica is a bacterium of significant concern due to its pathogenicity and ability to survive and persist in diverse environmental conditions. S. enterica has been associated with recalls in ready-to-eat foods. Traditional detection methods include Enzyme-Linked Immunosorbent Assay (ELISA), Polymerase Chain Reaction (PCR), and plate counting, which …

Fabrication And Performance Of Scalable Bio-Engineered Porous Layers For Efficient Co2 Capture, Mary Sharon Rose Bondugula

Theses and Dissertations

This dissertation addresses the critical challenge of mitigating climate change by advancing CO2 capture technologies. As global CO2 emissions continue to rise, effective methods for capturing and separating CO2 from industrial processes are essential to combat climate change. Existing CO2 capture systems, such as Pressure Swing Adsorption (PSA) and Temperature Swing Adsorption (TSA), often rely on packed bed designs that face limitations, including poor heat and mass transfer, slow gas diffusion, and low thermal conductivity, reducing their efficiency. To overcome these challenges, this dissertation explores innovative solutions by developing advanced adsorbent coatings and scalable bed configurations.

This research begins by …

Cyclic Thermal Stability Of Native Oxide Solar Thermal Absorbers On Femnnialcr High Entropy Alloys For Energy Applications, Xiaoxue Gao

Dartmouth College Ph.D Dissertations

High entropy alloys (HEAs) are promising candidates for cost-effective high-temperature materials in high-efficiency power cycles. A potential application is in concentrated solar power (CSP) systems, where native oxides of cost-effective FeMnNiAlCr HEAs can also synergistically serve as a high-efficiency solar thermal absorber. However, the huge and repetitive temperature change of the CSP system in day-night cycles greatly challenges its thermal stability. In this thesis, we investigated the cyclic oxidation behavior of FeMnNiAlCr HEAs to improve the optical performance and thermal stability of their native oxides as a solar absorber for next-generation CSP systems. We found that the duplex oxide scale …

Investigation Of Conductive Die-Top Thermal Capacitors During Short Circuit Operation Of Silicon Carbide Devices, Youssef Abotaleb

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Silicon carbide (SiC) power devices have garnered significant attention in recent years due to their superior thermal and electrical properties compared to traditional silicon devices. However, SiC power devices suffer from severe reliability issues arising from their mechanical properties. This is because the Young's modulus of SiC is about three times larger than that of silicon, which correspondingly raises the mechanical stresses acting on the bonding structure, often leading to device failure under power shock events.

Traditional packaging materials and designs tend to constrain SiC performance, as hot-spot temperature resulting from a power shock is one of the key factors …

Development Of Machine Learning-Based Tool For Prediction Of Long-Term Field Performance Of Asphalt Concrete Overlays In A Hot And Humid Climate, Elise Mansour

LSU Doctoral Dissertations

The performance of pavement plays a critical role in Maintenance, Rehabilitation and Reconstruction (MR&R) for highway agencies. Reliable and accurate estimation of pavement performance can be instrumental in prioritization of the limited resources and funding for highway agencies. The latter requires robust prediction models that can handle large-scale, real-world data and can forecast pavement performance in the long run. Unfortunately, the traditional performance prediction models have raised concerns regarding their efficiency and accuracy. It is because these models were based on a limited number of explanatory variables, were not up-to-date and were designed for forecasting short-term (up to five years) …

Biofabrication Of Tissue Constructs Using Protein-In-Polysaccharide Bioinks For Muscle Regeneration, Harshavardhan B

Theses and Dissertations

Myocardial infarction (MI) and volumetric muscle loss (VML) are debilitating conditions that severely affect patient quality of life and challenge healthcare systems, particularly in diagnosis and treatment. Conventional therapies often result in long recovery periods with limited functional restoration. Advances in regenerative medicine, especially extrusion-based 3D bioprinting, offer promising potential to improve the regeneration of complex tissues by precisely depositing cells and biomaterials layer-by-layer to create tailored tissue constructs.

A critical challenge in muscle tissue regeneration is developing protein-polysaccharide bioinks that closely mimic the native muscle tissue microenvironment. In this study, two protein-inpolysaccharide bioinks (alginate-fibrinogen and methylcellulose-gelatin-alginate) were developed to …

Synergistic Approaches For Microstructural Refinement, Enhanced Mechanical And Wear Behaviour In Additively Manufactured 17-4 Ph Stainless Steel, Pradeep Kumar S

Theses and Dissertations

The surface and microstructural characteristics of additively manufactured parts play a significant role under mechanical loading. Due to its high strength, tailorable mechanical properties by heat treatment, and ease of printability, the 17-4 precipitation hardened (PH) stainless steel is gaining attention in the additive manufacturing (AM) field.

Selective Laser Melting (SLM), one of the laser-based powder bed fusion (L-PBF) processes, is capable of making fully dense metallic parts with high geometrical fidelity and greater design flexibility at high resolution. The main factors limiting the adoption of SLM are poor surface roughness, anisotropic microstructure, and the formation of micro-pores in the …

Mechanical Properties Of Polymer Matrix Nanocomposites Reinforced With Varying Carbon Nanotube Geometries, Ethan Gaigalas, Zoe Kelemen

College of Engineering Summer Undergraduate Research Program

This study serves as part of an introduction to nanocomposite research at California Polytechnic State University, San Luis Obispo, and attempts to form an observational comparison between the performance of various CNT-Epoxy nanocomposites under drop weight testing. As a continuation of research on CNT-Epoxy nanocomposites, this study specifies three geometries of Multi-walled carbon nanotubes: straight (MWSCNTs), helical (MWHCNTs), and OH-functionalized straight (FMWSCNTs); and it compares their impact resistances to neat epoxy samples. Based on the total number of failed samples under a normalized impact energy of 0.335J/mm, it is observed that FMWSCNTs increase the impact resistance of Epoxy panels at …

Deep-Learning Based Microstructure Reconstruction And Generation, Cameron J. Maloney, Lucas Taliaferro

College of Engineering Summer Undergraduate Research Program

Characterizing the microstructural behavior of materials is crucial for understanding their properties and performance. Traditional imaging methods, such as optical microscopy and electron microscopy, are effective but costly and time-consuming. Computational approaches can reduce costs and time while expanding the accessibility of microstructural analysis through the generation of new microstructure images. Traditional computational approaches, namely descriptor-based approaches, are slow but effective in low-data scenarios. Modern approaches use machine learning (ML), which is faster but often requires a lot of data to approach the performance of descriptor-based methods. This research leverages a special data-efficient Generative Adversarial Network (GAN) architecture to artificially …

Solubility Characterization Of Organic Molecules For Aqueous Organic Redox Flow Batteries, Anthony W. Ferrell, Harkeerith K. Vij, Seamus D. Jones

College of Engineering Summer Undergraduate Research Program

The major obstacle to renewable energy sources is a lack of long-term energy storage capabilities. Energy produced during the day dissipates, leaving insufficient electricity for at night. The goal of the project is to design an Aqueous Organic Redox Flow Battery (AORFB) to act as long-term energy storage. Work has been done using machine learning to identify suitable compounds for the batteries. In this work there was no indication as to the aqueous solubility of the molecules; this controls the device’s energy storage capabilities. We used a machine learning model to determine the aqueous solubility of slightly more than 3000 …

Mapping Of The Potential To Substitute Plastic In Food Packaging In Finnish Supermarkets, Taina Lahtinen, Kirsi Kataja, Jari Viitanen, Vinay Kumar, Jussi Lahtinen, Ali Harlin

Journal of Applied Packaging Research

Single-use plastics (SUP), which are extensively utilized in food packaging, are one notable cause for the constantly growing littering issue. This novel study is one of the first attempts to systemically analyze food packaging data to reveal the potential for plastic packaging material reduction or substitution by utilizing a primary packaging material summary of single items sold in Finnish supermarkets. The outcome of the study indicates considerable dissimilarities among product groups concerning used packaging materials, weight, share of plastic, and sales volume. The analysis identified sweets and ready-to-eat meals as product groups for which there is a clear need, but …

Implementation Of Machine Learning Using Deep Neural Networks To Estimate The Failure Risk Caused By Leakage In Pressure Relief Devices, Adi Yudho Wijayanto, Yossi Andreano, M. Ali Yafi Rizky, Dedi Priadi

Journal of Materials Exploration and Findings

The primary objective of deploying Pressure Relief Device (PRD) equipment is to ensure the safety of pressure vessels within a pressurized system. Over time, PRD equipment may degrade and fail to perform its intended function, which must be identified as a failure mode. To mitigate potential risks associated with this, it is recommended that an approach such as risk-based inspection (RBI) be implemented. Despite the widespread adoption of RBI, the method relies on qualitative techniques, leading to significant variations in equipment risk assessments. This study proposes a novel risk analysis method that uses deep learning-based machine learning to develop a …

Effect Of Impurities In Supercritical Co2 Environment On Steel Corrosion Behavior – An Overview, Shilla Rizqi Widianto, Johny Wahyuadi Soedarsono, Rini Riastuti, Badrul Munir

Journal of Materials Exploration and Findings

Carbon capture, utilization, and storage (CCUS) technology is one of the available technologies to reduce presence of greenhouse gasses. Implementation of CCUS technology strongly relates with the CO₂ transportation from the capturing facility to the storage in the geological reservoir. The most economical method for large-scale and long-distance CO₂ transportation is using pipeline in supercritical phase. Moreover, presence of impurities such as water, O₂, SO₂, H₂S, NO₂ may cause detrimental effect towards carbon steel pipeline. This paper intends to provide an initial information for supercritical CO₂ pipeline material selection, which …

Hollow Connecting Rod Thin Wall Austempered Ductile Iron (Twadi) For Manufacturing Light Weight Components, Ricardina Freitas Da Silva, Bambang Suharno, Rianti Dewi Sulamet-Ariobimo

Journal of Materials Exploration and Findings

Efforts made by the automotive industry to reduce energy consumption have encouraged researchers to carry out various studies. One way is to make components lighter by casting thin wall austempered ductile iron (TWADI). Reducing the weight of components such as connecting rods (conrod) will result in lower energy consumption, but provided that these components still meet standards in terms of mechanical properties and microstructure or even exceed them. In this research, design optimization was applied to conrod by making the area I-beam zero mm (hollow), with hope that it can replace conrod Vespa PX-150. While the manufacturing process is divided …

Analysis Risk Based Inspection Api 581 On Lpg Spherical Tank At Pt. Xyz, Sigit Trahmawan, Eddy Sumarno Siradj, Jaka Fajar Fatriansyah

Journal of Materials Exploration and Findings

Liquified petroleum gas (LPG) spherical tanks are pressure vessel equipment for storing fuel gas products. The high pressure along with the fuel gas inside as flammable and combustible substance means that this equipment might result major accident hazard such as explosion, fires and environmental pollution. This study is aimed calculated and mitigate risk on 500 metric ton capacity LPG spherical tank using Risk-based inspection (RBI) analysis method that makes risk as its foundation. This RBI method uses quantitative analysis referring to API 581 to determine the risk of LPG Spherical Tank by determining the probability of failure (PoF) and the …

Root Cause Analysis Of Leakage Tube Boiler: A Study Case, Lydia Kartika Basaria Sitompul, Dedi Priadi

Journal of Materials Exploration and Findings

Oil and gas industry can have catastrophic implications for human life, the environment, and the economy. This paper investigated failure analysis using root cause analysis especially for boiler tube leakage of Heat Exchanger. Identify the issue using microscopic examination and energy dispersive x-ray analysis were conducted on the tube inside and outside surface to determine root cause of the failure. The formation of a protective film in the aluminum-brass tube during the starting stage is very important for ensuring adequate film protection throughout the service life of the heat exchanger. During this stage, exposure to unpolluted water is essential. The …

Local Charge Distortion Due To Cr In Ni-Based Concentrated Alloys, Jacob Fischer

All Theses

Due to the presence of multiple elements consisting of a range of atomic radii, local lattice distortion (LLD) is commonly observed in concentrated (and high entropy) alloys. However, since these elements also have diverse electronegativities, recent works show that atoms can have a range of atomic charges. In this work, using density functional theory (DFT), we investigate electronic charge distribution in face centered cubic (FCC) Ni-based alloys and find significant charge-density distortion in HEAs. Specifically, Cr atoms have large charge density distortion that results in a wide range of bond lengths, atomic charges, and electronic density of states in Cr-containing …

Predicting The Ductility Of Tungsten Based Bcc Refractory High Entropy Alloys: A Computational Science Driven Study, Akshay Korpe

All Theses

Bcc refractory high entropy alloys (HEAs) are a relatively new category of metallic alloys that promise excellent irradiation resistance and strength retention at high temperatures but exhibit brittle behavior at room temperatures limiting their formability. Understanding the deformation mechanisms and predicting their ductility at room temperature is a topic of interest in contemporary research.

In this work, multiple independent ductility criteria for quantifying the ductility of these HEAs were studied, calculated and compared using Density Functional Theory (DFT) calculations and continuum mechanics frameworks. These ductility parameters were calculated for various W-Ta-Cr-V alloys and the trends were analyzed for each criteria …

Fabrication And Characterization Of Lignin–Pva Hydrogels With Tunable Network Structures, Keturah Bethel

All Dissertations

The ability to directly tune the crosslinked network structure of hydrogels is crucial for their functional applications in various fields, such as water filtration, protein separation, and tissue engineering. By controlling the crosslink density of the hydrogel, one can directly alter the mesh size – i.e., the end-to-end distance between crosslink junctions – and, subsequently, directly alter the hydrogel performance. This work discusses the fabrication and characterization of soft composites containing the biopolymer, lignin, are discussed. Precisely, physically-crosslinked composite lignin–Poly(vinyl alcohol) (PVA) hydrogels were fabricated via the freeze-thaw (F/T) pathway, whereby solutions containing specified amounts of PVA and lignin were …

On The Structure, Energy, And Segregation Behavior Of Grain Boundaries In Metallic Systems, Yasir Mahmood

All Dissertations

Nearly all structural metallic systems are multi-component polycrystalline aggregates; their microstructures are composed of crystalline grains that are internally joined at grain boundaries (GBs). This thesis focuses on GB structure, energy, and chemistry, as these greatly influence many material properties and processes, including boundary dynamics during processing treatments or under operating conditions.

Using atomistic simulations, we examine the impact of metastable GB structures on solute segregation. A wide range of GB geometries and metastable structures are used in our study. The Al-Mg alloy is used because it is of interest for light weighting. The atomistic simulation results are used to …

Experimental Investigation On Mechanical Properties Of Pla Reinforced By Bamboo Fiber/Montmorillonite Clay Hybrid Composites And Analysis Of Machining Characteristics, Nirmal Kumar K

Theses and Dissertations

The study presents a comprehensive investigation into the development, characterization, and machining analysis of novel bio-based polymer hybrid composites comprising Polylactic acid (PLA), bamboo powders (BP), and montmorillonite clay particles (MMT). Initially, the hybrid composites were fabricated using a solvent-free stir casting process, optimizing the weight percentages of BP and MMT to enhance mechanical and thermal properties.

Mechanical tests, including tensile, flexural, and impact tests, along with thermal analysis using thermogravimetric analysis and differential scanning calorimetry, were conducted to evaluate the performance of the composites. In the subsequent phases, advanced machining techniques were employed to analyze the machining characteristics of …

Preparation Of Β-Ni (Oh)2 Nanosheet–Modified Glassy Carbon For Pseudocapacitors, Muhammad Buchari Setia Putra, Aliyah Aliyah, Afiten Rahmin Sanjaya, Respati Kevin Pramadewandaru, Hoeil Chung, Tribidasari Anggraningrum Ivandini

Makara Journal of Science

β-Nickel hydroxide (Ni(OH)₂) nanosheet–modified glassy carbon for pseudocapacitors was successfully prepared. The nanosheets were synthesized via a conventional growth seeding method combined with hydrothermal treatment. Transmission electron microscopy (TEM) characterization indicated the hexagonal structure of the nanosheets of around 15 nm in size, and X-ray diffraction (XRD) pattern confirmed the β-phase lattice crystal. These nanosheets used to modify the glassy carbon surface, increased the electroactive surface area by around 15 times. Furthermore, electrochemical investigation of the modified glassy carbon revealed an excellent performance and a specific capacitance of 628.01 F g⁻¹ at a 1 A g^{−1 …}

Spin And Charge Transport In Metallic Ferrimagnets And Disordered Magnetic Oxides, Leopoldo A. Hernandez

Electronic Theses and Dissertations

Recent efforts have been exploring the use of thin film synthetic ferrimagnets and disordered magnetic oxides for applications in spintronic devices. Due to the antiferromagnetic exchange interaction, ferrimagnetic materials offer the ultrafast dynamics of the antiferromagnetic exchange, with a net magnetization that can be influenced externally. With two, or more, competing ferromagnet sublattices, interesting properties arise that depend on the final magnetic landscape after growth of the material and it’s inherent magnetic anisotropy energies. Properties such as magnetic compensation temperatures, and perpendicular magnetic anisotropy are attractive for applications in spintronic memory and logic devices, some already being implemented in MRAM …

Effect Of Oxidation Of Graphene On Agglomeration And The Mechanical Properties Of Thermosetting Resins, Matthew A. Reil

Electronic Theses and Dissertations

Thermosetting resins are used extensively worldwide in applications ranging from adhesives to structural components. However, these resins generally fail in a brittle fracture mode which is undesirable in most situations. Graphene (G) and its derivatives have been considered as additives to epoxy for material property enhancement and varied results have been reported in the literature. In this work, the effects of the oxidation of G to graphene oxide (GO) on polymer interactions and plate agglomeration were studied by classical molecular dynamics (MD). Results from those simulations concluded that agglomerates were likely present in all G-based nanocomposites. The effect of these …

Wild Joy: An Exploration In Queer Spatial Dynamics, Kipper Thomas Reinsmith

Masters Theses

What does it mean to feel represented in a space?

What does a trans space look like?

How can we queer our interior spaces?

Our world is crafted by the many designers that have come before us. These systems, products, and spaces are built upon assumptions of the bodies that will use and occupy them—namely cisgender, able-bodied, straight folks.

Designing and creating objects as a trans person is an act of radical nature. To take up space, to design for trans luxury, for the sake of beauty, for joy itself, feels counterintuitive to the narratives we’ve been served: that of …

Assessing Global Engagement Interventions To Advance Global Engineering Competence For Engineering Formation, Scott Schneider, Erick S. Vasquez-Guardado, Corinne Mowrey, Michael Moulton, Homero Murzi, Matthew A. Witenstein

Chemical and Materials Engineering Faculty Publications

This paper summarizes the work performed during the first year of a collaborative Research Initiation in Engineering Formation (RIEF) project focused on assessing the formation of a global learner mindset in engineering students through the use of different types of global engagement interventions without extended international travel. During this year the global engagement interventions have been developed, piloted, and assessed using the Global Engagement Survey (GES) and Global Engineering Competency Scale (GECS) instruments in a pre and post format. The assessment results helped the research team update the interventions and refine the assessment strategy, including the addition of new qualitative …

Work In Progress: Exploring The Impact Of International Experiences On The Development Of Students’ Entrepreneurial Mindset, Olgha Bassam Qaqish, Marcia Poole, William Pennock, Erick S. Vasquez-Guardado, Fahmidah Ummul Ashraf

Chemical and Materials Engineering Faculty Publications

International experiences, including collaborative online international learning (COIL) experiences that naturally increase accessibility, are of interest to many undergraduate students. These experiences provide educators a unique opportunity to develop a student's entrepreneurial mindset (EM). Additionally, hands-on experiences aligned with the National Academy of Engineering’s (NAE) grand challenge themes (Sustainability, Security, Health, and Joy of Living) support connections between the experience, disciplinary knowledge, multicultural awareness, and EM. Through this Work-in-Progress (WiP) study, we seek to answer: 1) How do international experiences influence undergraduate science and engineering students’ EM, and 2) How does the international experience modality (i.e., study abroad or COIL) …

Enhancing Entrepreneurial Minded Learning Of Process Control And Heat Transfer Concepts Using Micromoments And Concept Maps, Erick S. Vasquez-Guardado, Ricardo Gomez Gonzalez, Jean M. Andino, Nilza D. Aples, Xiaojing Yuan

Chemical and Materials Engineering Faculty Publications

The Entrepreneurially Minded Learning (EML) Framework seeks to infuse an Entrepreneurial Mindset in engineering students. The EML framework is founded on the 3 C’s principles of curiosity, connections, and creating value. Assessing EML efforts, however, is a well-known challenge for many engineering courses that do not have a design component. Through concept maps and micromoment activities, this work seeks to answer the following questions: Does implementing micromoment activities enhance students’ EML in two core areas of chemical engineering, i.e., heat transfer and process controls? A secondary research question is whether introducing a physical device in lectures enhances students’ EML. The …

Using Micromoments And Concept Maps To Enhance Entrepreneurially Minded Learning Of Indoor Air Pollution Control, Jean M. Andino, Erick Salvador Vasquez-Guardado, Ricardo Gomez Gonzalez, Xiaojing Yuan, Nilza D. Aples

Chemical and Materials Engineering Faculty Publications

Micromoments targeted toward indoor air quality were introduced to students in an Air Quality Engineering course to enhance their entrepreneurial mindset. Three micromoment activities, i.e., “Question Frenzy”, “Make It Relevant”, and “How Do We Make It Better?” that are linked, respectively, to the curiosity, connections, and creating value elements of EM were deployed in the class in the context of the use of a Corsi Rosenthal cube (a do-it-yourself structure that has recently become popular as an inexpensive way to reduce indoor particle pollution). Students generated concept maps pre-and post- micromoment intervention using the freely available CMap Tools software. The …