Materials Science and Engineering Commons^™

An In Situ Fourier Transform Infrared Spectroelectrochemical Study On Alcohols Electrocatalytic Oxidation At Pd Electrode In Acidic Solution, Hai-Ping Huang, Lian-Qin Wang, Pei-Kang Shen

Journal of Electrochemistry

The methanol and ethylene glycol electrooxidation on palladium electrode in acidic solution has been investigated by cyclic voltammetry and in situ Fourier transform infrared spectroelectrochemistry. It shows that the oxidation of methanol and ethylene glycol at Pd electrode cannot proceed until over 1.5 V in acidic and neutral media. The overpotential decreases and the peak current density increases with the reduction in pH values. The formation of the oxygen-containing species significantly affects the alcohol oxidation on Pd electrode. The in situ FTIR spectroscopic measurements show that the oxidation products of ethylene glycol on Pd electrode are CO₂ and oxalic …

In-Situ Surface Enhanced Raman Scattering Electrochemical Investigation Of 4-Aminoantipyrine On Silver Electrode, Li-Jun Zhang, Wei Song, Ling Chen, Zong-Rang Zhang, Hai-Feng Yang

Journal of Electrochemistry

In this paper, 4-AAP was self-assembled on silver surface to form monolayers. Surface-enhanced Raman Spectroscopy (SERS) was used to in-situ investigate the adsorption mechanism of the 4-aminoantipyrine(4-AAP) on silver surface dependent on shifting potentials and the effect of solution pH. Based on density functional theory(DFT) calculation of vibration modes,approximate assignment of 4-AAP SERS spectrum was conducted. In situ SERS spectral electrochemical experiments indicated that the 4-AAP monolayers experience a dynamic adsorption process from a tilted fashion to a more vertical mode for benzene ring and more parallel for pyrine ring with the potential applied toward more negative voltages. The complete …

Boron Carbide Based Solid State Neutron Detectors: The Effects Of Bias And Time Constant On Detection Efficiency, Nina Hong, John Mullins, Keith Foreman, Shireen Adenwalla

Shireen Adenwalla Papers

Neutron detection in thick boron carbide(BC)/n-type Si heterojunction diodes shows a threefold increase in efficiency with applied bias and longer time constants. The improved efficiencies resulting from long time constants have been conclusively linked to the much longer charge collection times in the BC layer. Neutron detection signals from both the p-type BC layer and the n-type Si side of the heterojunction diode are observed, with comparable efficiencies. Collectively, these provide strong evidence that the semiconducting BC layer plays an active role in neutron detection, both in neutron capture and in charge generation and collection.

The Characterization And Analysis Of In-Vitro And Elevated Temperature Repassivation Of Ti-6al-4v Via Afm Techniques, Aaron J. Guerrero

Master's Theses

ABSTRACT

The Characterization and Analysis of In-vitro and Elevated Temperature Repassivation of

Ti-6Al-4V via AFM Techniques

Aaron J Guerrero

Research in the corrosion of orthopaedic implants is a growing research field where implants have been known to show adverse effects in patients who have encountered the unfortunate dissolution of their implants due to corrosion. Once corrosion begins within the body, many adverse biological reactions can occur such as late on-set infections resulting in severe health complications. The focus of this research is specifically related to the problem of late on-set infections caused by localized corrosion of orthopaedic implants. In medical …

Enhanced Light Extraction Efficiency From Gan Light Emitting Diodes Using Photonic Crystal Grating Structures, Simeon S. Trieu

Master's Theses

Gallium nitride (GaN) light emitting diodes (LED) embody a large field of research that aims to replace inefficient, conventional light sources with LEDs that have lower power, higher luminosity, and longer lifetime. This thesis presents an international collaboration effort between the State Key Laboratory for Mesoscopic Physics in Peking University (PKU) of Beijing, China and the Electrical Engineering Department of California Polytechnic State University, San Luis Obispo. Over the course of 2 years, Cal Poly’s side has simulated GaN LEDs within the pure blue wavelength spectrum (460nm), focusing specifically on the effects of reflection gratings, transmission gratings, top and bottom …

Nano/Micro-Structured Electrode Materials For Lithium-Ion Batteries, Yu-Guo Guo, Zhong-Li Wang, Xing-Long Wu, Wei-Ming Zhang, Li-Jun Wan

Journal of Electrochemistry

Nanostructured materials are currently of interest as high performance anodes and cathodes for rechargeable lithium-ion batteries because of their novel nano-size effects and significantly enhanced kinetics. This review paper describes some recent developments in this field,addressing the size effects,morphology effects,as well as the functions of carbon coating layers toward lithium storage. Several"kinetically stabilized"nano/microstructured electrode materials and high-rate electrode materials with mixed-conducting networks based on the work of the authors are highlighted for illustration.

Electrocatalytic Oxidation Of Hcooh At Au(Core)-Pd(Shell)-Pt(Cluster) Nanocubes, Qing-Ning Jiang, Huan Li, Ning Yang, Ping-Ping Fang, Feng-Ru Fan, Zhong-Qun Tian

Journal of Electrochemistry

Gold nanocubes were synthesized by a two-step seed-mediated growth method. The Aucore-Pdshell and Au_core-Pd_shell-Pt_cluster nanocubes with controllable shell thickness of Pd and cluster coverage of Pt were synthesized by simply changing the amount ratio of H₂PdCl₄ or H₂PtCl₆. The samples were characterized by scanning electron microscope (SEM) , transmission electron microscopc (TEM) and cyclic voltammetry (CV). CV was then used to make a systematic study on the dependence of the electrocatalytic properties on the shell thickness of Au_core-Pd_shell and Pt coverage of Au_core-Pd …

Prerapation And Supercapacitor Property Of Mesoporous Carbon Nanofibers, Yong-Wen Wang, Ming-Bo Zheng, Jian Cao, Jie-Ming Cao, Guang-Bin Ji, Jie Tao

Journal of Electrochemistry

Two different mesoporous carbon nanofibers with large mesopore or core-shell structure were prepared by using the resol/F127 mixture to fill the AAO template. The morphology and structural parameters of the samples were characterized by SEM,TEM,and N₂ adsorption-desorption analysis. The supercapacitive behaviors of the electrodes were tested by cyclic voltammetry and galvanostatic charge-discharge. The results show that the specific capacitances of mesoporous carbon nanofibers increased obviously and the fine supercapacitive performances were achieved at high scan rate or large current density.

Nano-Sized Au On Nickel Foam As Cathode Of Alkaline Al-H2O2 Semi Fuel Cell, Shu-Li Chen, Bang-An Lu, Yao Liu, Gui-Ling Wang, Dian-Xue Cao

Journal of Electrochemistry

Nano-sized Au particles were deposited on a nickel foam substrate by a fast spontaneous deposition method using AuCl₃ as the source of Au. The effects of AuCl₃ concentration and deposition time on the size and distribution of Au particles,and the performance of the obtained Au/Ni electrode as the cathode of Al-H₂O₂ semi fuel cell were investigated. It was found that after the nickel foam was immersed in a 2 mmol·L^-1 AuCl₃ solution for 60 s,Au particles with diameters smaller than 100 nm were deposited on its surfaces and cover the surface completely. The …

Production Of Multiwall Carbon Nanotuse For Alcohol Sensor Application., Ebtehal Saleh Alshaqaq

Student Works (2010-2019)

Multiwall carbon nanotube/polyethylene oxide (PEO), multiwall carbon nanoube/polyvinyl alcohol(PVA) and multiwall carbon nanotube/ polyvinyl alcohol(PVA)/zinc oxide(ZnO) have been tested as chemical sensors and detailed study on the effect of different gas concentration and material properties on gas sensitivity is presented. Initial composites were prepared by a simple solution casting and characterized by x-ray diffraction for ZnO, Fourier transform infra-red spectroscopy (FTIR) and scanning electron microscopy (SEM) to demonstrate crystallite size of ZnO, the morphology and surface area respectively. On the other hand, MWCNT/PEO , MWCNT/PVA , MWCNT/PVA/ZnO were prepared with different loading MWCNT and ZnO. The chemical sensing properties of …

Analysis Of Conjugated Polymer Nanotubules Formed By Template Wetting Nanofabrication, Steven D. Bearden Jr.

Doctoral Dissertations

Semiconducting and optoelectric conjugated polymers have potential in micro and nano-electronic applications. Their widely tunable physical conformations and orientations make these polymers ideal material for engineering small scale devices. The polymers have been incorporated into several electronic devices including light-emitting diodes, solar cells, and field-effect transistors. Widespread adoption of these materials will not be a reality until the issues of poor device performance, short lifespans, and device degradation are resolved.

Nanostructures have been demonstrated to have improvements in molecular ordering and electronic transport. In the work presented here, tubular nanostructures of conjugated polymers fabricated by the template wetting nanofabrication process …

Morphological Evolution Of Single-Crystal Ultrathin Solid Films, Mikhail Khenner

Mathematics Faculty Publications

An introduction to mathematical modeling of ultrathin solid films and the role of such modeling in nanotechnologies: Educational presentation for senior physics majors

Morphological Evolution Of Single-Crystal Ultrathin Solid Films, Mikhail Khenner

Mathematics Faculty Publications

An introduction to mathematical modeling of ultrathin solid films and the role of such modeling in nanotechnologies: Educational/Research presentation for senior physics majors

Preparation And Electrochemical Behavior Of Li4Ti5O12 Nanosheets As Anode Material For Lithium Ion Battery, Yi-Fei Wang, Yu-Feng Tang, Zheng Qiu, Li Yang

Journal of Electrochemistry

Spinel lithium titanate(Li₄Ti₅O₁₂) nanosheets with a size range of 200 ～400 nm were synthesized by hydrothermal process from the amorphous hydrous titanium oxide precursors.The as-prepared products were characterized by X-ray powder diffraction(XRD),scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The electrochemical behaviors of Li₄Ti₅O₁₂ electrode in conventional organic electrolyte and ionic liquid electrolyte were investigated by using cyclic voltammetry,galvanostatic charge-discharge and AC impedance techniques.The experimental results indicate that the as-prepared nanostructured Li₄Ti₅O₁₂,evaluated as anode material,exhibited good reversibility and cycle performance.It is expected to be a …

Electrocatalytic Reduction Of L-Cystine At Pb/Nanotio2 Film Electrode, Dao-Bao Chu, Feng Wang, Ying Xiao, Xue-Jiao Zhang

Journal of Electrochemistry

The nanoporous Ti-based TiO₂ films electrodes modified with Pb particles(Pb/nanoTiO₂) were prepared by using anodization and potentiostatic electro-deposition.The optimum deposition conditions were determined by comparing with various deposition potentials and time.The SEM analyses indicated that the TiO₂ films were homogeneous nanoporous structure,and the Pb particles well dispersed on the TiO₂ films.The L-cystine electrocatalytic activity reduction on the Pb/nanoTiO₂ film electrodes was investigated by cyclic voltammetry and Chronoamperometric curves.The results showed that this type of the electrode posseses high acticity and stability.

Oscillatory And Monotonic Modes Of Long-Wave Marangoni Convection In A Thin Film, Sergey Shklyaev, Mikhail Khenner, Alexei Alabuzhev

Mathematics Faculty Publications

We study long-wave Marangoni convection in a layer heated from below. Using the scaling k=O Bi, where k is the wave number and Bi is the Biot number, we derive a set of amplitude equations. Analysis of this set shows presence of monotonic and oscillatory modes of instability. Oscillatory mode has not been previously found for such direction of heating. Studies of weakly nonlinear dynamics demonstrate that stable steady and oscillatory patterns can be found near the stability threshold.

Oscillatory And Monotonic Modes Of Long-Wave Marangoni Convection In A Thin Film, Sergey Shklyaev, Mikhail Khenner, Alexei Alabuzhev

Mathematics Faculty Publications

We study long-wave Marangoni convection in a layer heated from below. Using the scaling k=O Bi, where k is the wave number and Bi is the Biot number, we derive a set of amplitude equations. Analysis of this set shows presence of monotonic and oscillatory modes of instability. Oscillatory mode has not been previously found for such direction of heating. Studies of weakly nonlinear dynamics demonstrate that stable steady and oscillatory patterns can be found near the stability threshold.

Investigation Of The Threshold Voltage Shift Effect Of La2o3 On Tin/Hfo2/La2o3/Sio2/Si Stacks, Ming Di

Legacy Theses & Dissertations (2009 - 2024)

The semiconductor industry continues to scale (shrink) transistor dimensions to both increase the number of transistors per integrated circuit and their speed. One important aspect of scaling is the need to decrease the equivalent oxide thickness of the transistor gate dielectric while minimizing leakage current. Traditional thin layer SiO2 or SiOxNy films have been replaced by higher dielectric constant film stacks Here we study one example, the HfO2/La2O3/SiO2 stack. This dissertation describes an investigation of the use of La2O3 to reduce the threshold voltage of TiN/HfO2/SiO2/Si stacks (high-k/metal gate stacks). A significant aspect of this study is the determination of …

Fabrication And Characterization Of Nanomaterials Grown By Electron Beam Induced Deposition Process, Juntao Li

Legacy Theses & Dissertations (2009 - 2024)

Platinum&ndash and tungsten&ndashcontaining materials were grown on bulk substrates from a variety of precursors including (CH₃)₃CH₃C₅H₄Pt, W(CO)₆, WF₆, and Pt(PF₃)₄ in either a high vacuum dual beam focused ion beam/scanning electron microscope (FIB&ndashSEM) or an environmental scanning electron microscope (ESEM). The effects of deposition conditions on the growth kinetics, microstructure and composition of the grown materials, structural and chemical homogeneity of impurities inside the deposits as well as the resistivity were investigated.

Nanoabrasives Retention And Removal Mechanisms In Polyurethane Pads For Copper Cmp, Iftikhar Ul-Hasan

Legacy Theses & Dissertations (2009 - 2024)

The continued reduction in integrated circuit (IC) feature size requires similar reductions in surface defectivity. A key source of surface defects in IC fabrication processes stems from nanoabrasives used in chemical-mechanical planarization (CMP) processing. During CMP processing, polished surfaces are more vulnerable to defects including scratching, nanoabrasive particle adhesion and nanoabrasive agglomerate adhesion. The removal of these nano-sized particles is a priority for the IC fabrication industry and is reflected in the 2008 ITRS defect budget. However, there is insufficient technical understanding regarding the retention of residual nanoabrasives on the surfaces of the CMP pad following a CMP process and …

Morphological, Structural, And Optical Studies Of Undoped And Doped-Zno Nanostructure., Ramin Yousefi

Student Works (2010-2019)

Research concerning one-dimensional nanomaterials has grown tremendously ever since carbon nanotubes were discovered by Iijima (1991), silicon nanowires were grown by Lieber's group (1998), and ZnO nanowires and nanobelts were found by Wang's group from Georgia Tech (Pan et al., 2001). Such researches on one-dimensional structures have been one of the most important branches of science during recent decades. We can now observe the impact of these studies on the technology of one-dimensional materials and also the advanced prospect of developing new technologies. Based on this motivation, this thesis attempts to investigate some unknown properties of ZnO nanostructures as …

Synthesis And Characterization Of Zinc Oxide Nanostructures., Khalifa Said Zahran Al-Azri

Student Works (2010-2019)

The growth mechanism, morphology, structure and optical properties of the ZnO nanostructures grown on bare and gold-coated silicon substrates using carbothermal reaction at atmospheric pressure were investigated under different growth conditions. The ZnO nanostructures formed were studied as a function of substrate location, furnace temperature, Ar gas flow rate, deposition time and ZnO powder to carbon powder mass ratio. The morphology and structure of the samples were characterized using the fieldemission scanning electron microscopy (FESEM), energy dispersive x-ray spectroscopy(EDX) spectrum, x-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). It was found that in both silicon and gold-coated silicon …

Synthesis And Characterization Of Silicon Oxide And Silicon Carbide Nanostructures., Majid Salim Mohammed Al-Ruqieshi

Student Works (2010-2019)

Silicon oxide nanostructures have attracted extensive interests in recent years due to their physical and optical properties. SiOx nanostructures are synthesized by catalytic and non-catalytic approaches. With catalytic approach, long and uniform amorphous silicon oxide nanowires, nanofibers (comet and tree like), nanocakes and nanocages were synthesized on Si substrate by carbothermal evaporation reactions of TiO2 at high temperature. The SiOx nanowires were about 13 nm to 243 nm in diameters and 194 nm to several microns in length and the nanofibres with diameter between 8 nm to 30 nm and around 50 nm to 2.5μm in length. The diameter and …

Synthesis And Characterization Of Limpo[4] (M=Mn, Ni And Fe) Olivine Materials., Azlin Sanusi

Student Works (2010-2019)

Lithium transition metal phosphate, LiMPO4 compounds with olivine structure namely LiMnPO4, LiNiPO4 and LiFePO4 were successfully synthesized in the present work. LiMnPO4 and LiNiPO4 were synthesized by the sol-gel method with tartaric acid as the chelating agent. LiFePO4 was synthesized via the chemical precipitation and low temperature sterilizer heating method. TGA was carried out on LiMnPO4 and LiNiPO4 samples to determine the firing temperature of the gel precursor and the thermal stability of the prepared samples. LiMnPO4 was heated for 15 hours at various temperatures and LiNiPO4 was formed at 1000 oC with firing time of 24 hours. Firing of …

Giant Raman Enhancement On Nanoporous Gold Film By Conjugating With Nanoparticles For Single-Molecule Detection, Lihua Qian, Biswajit Das, Yan Li, Zhilin Yang

Electrical & Computer Engineering Faculty Research

Hot spots have the contradictively geometrical requirements for both the narrowest interstices to provide strong near-field coupling, and sufficient space to allow entrance of the analytes. Herein, a two-step method is employed to create hot spots within hybrid nanostructures, which consist of self-supported nanoporous gold films with the absorbed probes and subsequent nanoparticle conjugates without surface agents or mechanical motion. The molecules confined into 1 nm interstice exhibit 2.9 × 10⁷ times enhancement in Raman scattering compared to pure nanoporous gold. Giant enhancement primarily results from strong near-field coupling between nanopore and nanoparticle, which is theoretically confirmed by finite-difference …

Thermocapillary Effects In Driven Dewetting And Self-Assembly Of Pulsed Laser-Irradiated Metallic Films, Mikhail Khenner

Mathematics Faculty Publications

A mathematical model for the evolution of pulsed laser-irradiated, molten metallic films has been developed using the lubrication theory. The heat transfer problem that incorporates the absorbed heat from a single laser beam or the interfering laser beams is solved analytically. Using this temperature field, we derive the 3D long-wave evolution PDE for the film height. To get insights into dynamics of dewetting, we study the 2D version of the evolution equation by means of a linear stability analysis and by numerical simulations. The stabilizing and destabilizing effects of various system parameters, such as the reflectivity, the peak laser beam …

Thermocapillary Effects In Driven Dewetting And Self-Assembly Of Pulsed Laser-Irradiated Metallic Films, Mikhail Khenner

Mathematics Faculty Publications

A mathematical model for the evolution of pulsed laser-irradiated, molten metallic films has been developed using the lubrication theory. The heat transfer problem that incorporates the absorbed heat from a single laser beam or the interfering laser beams is solved analytically. Using this temperature field, we derive the 3D long-wave evolution PDE for the film height. To get insights into dynamics of dewetting, we study the 2D version of the evolution equation by means of a linear stability analysis and by numerical simulations. The stabilizing and destabilizing effects of various system parameters, such as the reflectivity, the peak laser beam …

Thermocapillary Effects In Driven Dewetting And Self-Assembly Of Pulsed Laser-Irradiated Metallic Films, Mikhail Khenner

Mathematics Faculty Publications

A mathematical model for the evolution of pulsed laser-irradiated, molten metallic films has been developed using the lubrication theory. The heat transfer problem that incorporates the absorbed heat from a single laser beam or the interfering laser beams is solved analytically. Using this temperature field, we derive the 3D long-wave evolution PDE for the film height. To get insights into dynamics of dewetting, we study the 2D version of the evolution equation by means of a linear stability analysis and by numerical simulations. The stabilizing and destabilizing effects of various system parameters, such as the reflectivity, the peak laser beam …

Preparation Of Pt Nanoflower/Zno Composites Arrays And Their Electrocatalysis For Methanol Oxidation, Li Gao, Yi-Feng E, Lou-Zhen Fan

Journal of Electrochemistry

The Pt nanoflower/ZnO(PtNF/ZnO) nanorod composites arrays were electrochemically prepared by controlling the hydrophobicity and the hydrophilicity of ZnO nanorods arrays.The Pt nanoflowers grew on the tip of ZnO nanorods,which maintain the vertical array of Zno nanorods with a high degree of size uniformity and high surface area.Compared with Pt nanoparticle covered ZnO nanorod arrays,which were prepared by controlling the hydrophilicities of ZnO nanorods and Pt nanoparticles,the PtNF/ZnO displayed highest electrocatalytic activities for the oxidation of methanol.

Enhanced Visible Light Photoelectrochemical Performances With Nitrogen Doped Tio2 Nanowire Arrays, Xiao-Jun Lv, Yue-Ming Li, Hao Zhang, Da Chen, Jennifer Hensel, Jin Z Zhang, Jing-Hong Li

Journal of Electrochemistry

Self-organized anodic anatase TiO₂ nanowire arrays doped with nitrogen have been successfully fabri-cated and their photoelectrochemical(PEC) properties have been characterized and found to be substantially im-proved compared to undoped nanowires or commercial P25 nanoparticles.Photocurrent measured with monochro-matic incident light showed that the incident photon-to-current efficiency(IPCE,%) values of nanowire arrayelectrodes with or without N-doping were obviously higher than that of commercial P25 nanoparticle electrodes,and nitrogen-doped TiO₂ nanowire arrays(NTNA) had noticeable absorption in the visible region.The NTNAelectrodes showed the highest photocurrent density and power conversion efficiency under 100 mW/cm² visiblelight illumination.A maximumolphotoconversion efficiency of 0.52% was achieved for the …