Materials Science and Engineering Commons^™

Electrochemical Performances Of Layered Polypyrrole/Chemically Reduced Graphene Oxide Nanocomposites As Supercapacitor Electrodes, Si-Zhe Xu, Xue-Jiao Zhou, Kun Wu, Yong-Qiang Yang, Hai-Xia Wu

Journal of Electrochemistry

Nanocomposites of polypyrrole (Ppy) and chemically reduced graphene oxide (CRGO), Ppy/CRGO, have been fabricated through in-situ polymerization of pyrrole on graphene oxide (GO) sheets. The as-synthesized Ppy/CRGO composites were characterized complementarily using scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and Fourier transformed infrared spectroscopy (FT-IR). By controlling the initial ratio of the GO to pyrrole, the layered composites could be obtained and their thickness could be tuned properly. The Ppy/CRGO electrodes were prepared using a mechanical compressing technique and their electrical conductivity and electrochemical properties were characterized systematically. We demonstrated that as electrodes for supercapacitor, the Ppy/CRGO composites with Ppy …

Semiconductor Nanocrystals: From Quantum Dots To Quantum Disks, Zheng Li

Graduate Theses and Dissertations

The bottom-up colloidal synthesis opened up the possibility of finely tuning and tailoring the semiconductor nanocrystals. Numerous recipes were developed for the preparation of colloidal semiconductor nanocrystals, especially the traditional quantum dots. However, due to the lack of thorough understanding to those systems, the synthesis chemistry is still on the empirical level. CdS quantum dots synthesis in non-coordinating solvent were taken as a model system to investigate its molecular mechanism and formation process, ODE was identified as the reducing agent for the preparation of CdS nanocrystals, non-injection and low-temperature synthesis methods developed. In this model system, we not only proved …

Probing And Controlling Fluid Rheology At Microscale With Magnetic Nanorods, Alexander Tokarev

All Dissertations

This Dissertation is focused on the development of new methods for characterization and control of fluid rheology using magnetic nanorods. This Dissertation consists of five chapters. In the first chapter, we review current microrheologial methods and develop a Magnetic Rotational Spectroscopy (MRS) model describing nanorod response to a rotating magnetic field. Using numerical modeling, we analyze the effects of materials parameters of nanorods and fluids on the MRS characteristic features. The model is designed for a specific experimental protocol. We introduce and examine physical parameters which can be measured experimentally. The model allows identification of MRS features enabling the calculation …

Multidentate Resorcinarene Surfactants For The Phase Transfer Of Metal Nanoparticles And Nanodiamonds: Applications In Catalysis And Diamond Film Growth, Vara Prasad Sheela

Chemistry & Biochemistry Theses & Dissertations

One main objective of the present work is to functionalize cuboctahedral platinum nanoparticles with various multidentate resorcinarene surfactants and study their influence in determining their catalytic activity. We hypothesized that catalytically active and recyclable catalysts can be achieved by incomplete yet strong passivation of the nanoparticle surfaces by using multidentate resorcinarene surfactants. We have developed phase transfer protocols for functionalizing cuboctahedral platinum nanoparticles with resorcinarene thiol or amine. Fluorescence assay confirmed that both these nanoparticles contained almost comparable unpassivated metal area. The activity of such phase transferred nanoparticles was tested in the catalytic hydrogenation of allyl alcohol. The conversion of …

Preparation And Characterization Of Prussian Blue Modified Nanoelectrode, Wei Wang, Bao-Fa Su, Dong-Ping Zhan

Journal of Electrochemistry

The Pt nanoelectrodes were fabricated by using a laser-based pipet puller and the recessed nanoelectrodes were prepared by etching of disk Pt nanoelectrodes wtih high frequency ac voltage. Prussian blue microcrystal was synthesized electrochemically on the both disk and recessed Pt nanoelectrodes. The strength of mechanical adhesion for the Prussian blue microcrystal on the nanoelectrode was enhanced. A novel method for the controllable synthesis of single particle is proposed, which has potential applications in modified electrodes and single particle electrocatalysis.

Preparation And Electrochemical Performance Of Tio2/Gns Nanocomposite As Anode Materials For Lithium-Ion Batteries, Lin-Lin Qin, Huan Zhang, Xiao-Jing Liu, Jian-Hui Xu, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The honeycomb-like porous TiO₂/graphenes (TiO₂/GNs) nanocomposite was prepared by a reflux method. SEM and TEM results showed that nanosized anatase TiO₂ (about 5~10 nm) were dispersed uniformly on the surface of the GNs. The TiO₂/GNs composite showed excellent rate and cycling performance: A stable charge capacity of 169.5 mAh·g^-1 was obtained at 30C, and can restore to 241.7 mAh·g^-1 while current went back to 1C. The stable charge capacity of TiO₂/GNs nanocomposite electrode up to 201.9 mAh·g^-1 was achieved at 10C in the first cycle, and could be …

Detection Of Pml/Rarî± Fusion Gene Using Gold Nanopaticles Modified Electrode By Chronocoulometry, Li-Man Wang, Li-Qing Lin, Shao-Huang Weng, Xin-Hua Lin, Yuan-Zhong Chen

Journal of Electrochemistry

A gold nanoparticles modified electrode was prepared by electrodeposition at constant potential. The sulfydryl modified probe was immobilized onto surface of gold nanoparticles via Au-S covalent bond and hybridized with complementary target DNA sequences, then the DNA sensor was fabricated for the detection of PML/RARα fusion gene by chronocoulometry in acute promyelocytic leukemia (APL). Scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS) were used to characterize the surface morphology of gold nanoparticles and the constructing process of sensor. With hexaammineruthenium(Ⅲ) chloride (RuHex) as a novel electrochemical indicator, the chronocoulometric DNA biosensor was employed to monitor artificial APL PML/RARα fusion …

Active Response Of Polymer Materials From External Stimuli – Solvents And Light; Grafting Reactions On Perovskite Layers, Jianxia Zhang

LSU New Orleans Theses and Dissertations

The active response of a series of polymeric materials was investigated. Both solvent activated and light activated thin films and wire systems show dynamic behaviors when exposed to different stimuli.

Solvent mediated fluxional behavior of polymer thin films involved extensive, rapid curling both on infusion and evaporation of good solvents. These films can be either lab-fabricated ones or commercial ones, and the curling behavior can be as fast as seconds. Conditions including polymer materials, chosen solvents, and film geometry can affect the behavior.

Methods that allowed for the creation and retention of distorted wire structures were also developed; the asymmetric …

Nanocharacterization Of Porous Materials With Atomic Force Microscopy, Yasemin Kutes

Master's Theses

Scanning Probe Microscopy techniques have proven very useful in the investigation of porous nanostructured surfaces. Especially, Atomic Force Microscopy (AFM) has been widely used due to its compatibility with non-conducting surfaces. In particular, AFM often complements other techniques like scanning and transmission electron microscopy by providing quantitative surface information coupled with nanoscale spatial resolution. Its ability to operate in fluid is also important, as this allows researchers to mimic the physiological environment of biological materials and systems. In this work, two main types of porous materials are studied with AFM, including Phosphoric Acid Fuel Cell (PAFC) electrode catalyst layers, and …

Physiochemical And Nanomanipulation Studies Of Carbon Nanomaterials, Siva Naga Sandeep Chalamalasetty

Graduate Theses and Dissertations

Carbon nanomaterials are, without a doubt, one of man's wonder creations. Though these nanomaterials are a very recent trend, extraordinary electromechanical properties and the light weightiness of these nanomaterials attracted the attention of researchers. Although vast research has been done since the start of the US nanotechnology initiative, much effort was in the area of synthesis and characterization of the nanomaterials. However, most of the traditional macroscopic material's theories fail at the nanoscale level, and since the material properties are dependent on size and structure at nanoscale level, the behavior of the carbon nanomaterials in different environments needs attention. High …

Electrochemical Performances Of Carbon-Coated Na2Ti6O13 Nanotubes, Guo-Ran Li, Shuai Sun, Xue-Ping Gao

Journal of Electrochemistry

With rutile TiO₂ and NaOH as starting materials, the Na₂Ti₆O₁₃ nanotubes were prepared by a hydrothermal reaction. The carbon-coated Na₂Ti₆O₁₃ nanotubes were obtained by treating the Na₂Ti₆O₁₃ nanotubes for 4 h in glucose aqueous solutions containing 0.1 mol·L^-1 NaOH. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microcopy (TEM). The results showed that the dimensions of carbon-coated Na₂Ti₆O₁₃ nanotubes were 14 ~ 19 nm of outer diameter, 2 ~ 5 …

Electrochemical Preparation Of Nanostructural Pt-Ni And Pd-Ni Films For Ethanol Electro-Oxidation, Chen-Zhong Yao, Hui-Xuan Ma, Bo-Hui Wei

Journal of Electrochemistry

The Pt-Ni and Pd-Ni films were successfully prepared on Ti substrates by electrodeposition method. The porous Pt-Ni nanoflakes appeared to be uniform with the thickness of the slices about 10 ~ 20 nm. The porous Pd-Ni nanoparticles with a flower shape appeared to be uniform with the diameters of 50 ~ 60 nm. The XRD patterns also indicated that the Pd-Ni and Pt-Ni nanostructures have the poor crystallinity. The onset potentials of ethanol oxidation were negatively shifted to –0.74 V on Pt-Ni electrodes and –0.71 V on Pd-Ni electrodes, respectively. Addition of Ni could enhance catalytic activities and antitoxic properties …

Functional Magnetic Nanoparticles, James Gass

USF Tampa Graduate Theses and Dissertations

Nanoparticle system research and characterization is the focal point of this research and dissertation. In the research presented here, magnetite, cobalt, and ferrite nanoparticle systems have been explored in regard to their magnetocaloric effect (MCE) properties, as well as for use in polymer composites. Both areas of study have potential applications across a wide variety of interdisciplinary fields.

Magnetite nanoparticles have been successfully dispersed in a polymer. The surface chemistry of the magnetic nanoparticle proves critical to obtaining a homogenous and well separated high density dispersion in PMMA. Theoretical studies found in the literature have indicated that surface interface energy …

Peridynamic Model For Dynamic Fracture In Unidirectional Fiber-Reinforced Composites, Wenke Hu, Youn Doh Ha, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

We propose a computational method for a homogenized peridynamics description of fiber-reinforced composites and we use it to simulate dynamic brittle fracture and damage in these materials. With this model we analyze the dynamic effects induced by different types of dynamic loading on the fracture and damage behavior of unidirectional fiber-reinforced composites. In contrast to the results expected from quasi-static loading, the simulations show that dynamic conditions can lead to co-existence of and transitions between fracture modes; matrix shattering can happen before a splitting crack propagates. We observe matrix–fiber splitting fracture, matrix cracking, and crack migration in the matrix, including …

Metal Oxide Graphene Nanocomposites For Organic And Heavy Metal Remediation, Tanvir E. Alam

USF Tampa Graduate Theses and Dissertations

This thesis consists of two research problems in the water decontamination area. In the first work, the main focus is to understand the structure and photocatalytic activity of titanium dioxide with graphene (G-TiO2) which is synthesized by using sol-gel method. The photocatalytic activity of TiO2 is limited by the short electron hole pair recombination time. Graphene, with high specific surface area and unique electronic properties, can be used as a good support for TiO2 to enhance the photocatalytic activity. The obtained G-TiO2 photocatalysts has been characterized by X-Ray Diffraction (XRD), Raman Spectroscopy, Transmission Electron Microscopy (TEM), FTIR Spectroscopy and Ultraviolet …

The Design And Fabrication Of A Microfluidic Reactor For Synthesis Of Cadmium Selenide Quantum Dots Using Silicon And Glass Substrates, Peter Robert Gonsalves

Master's Theses

A microfluidic reactor for synthesizing cadmium selenide (CdSe) quantum dots (QDs) was synthesized out of a silicon wafer and Pyrex glass. Microfabrication techniques were used to etch channels into the silicon wafer. Holes were wet-drilled into the Pyrex glass using a diamond-tip drill bit. The Pyrex wafer was anodically bonded to the etched silicon wafer to enclose the microfluidic reactor. Conditions for anodic bonding were created by exposing the stacked substrates to 300V at ~350oC under 5.46N of force. A syringe containing a room temperature CdSe solution was interfaced to the microfluidic reactor by using Poly (dimethylsiloxane) (PDMS) as an …

Controlling Nanoparticles Formation In Molten Metallic Bilayers By Pulsed-Laser Interference Heating, Mikhail Khenner, Sagar Yadavali, Ramki Kalyanaraman

Mathematics Faculty Publications

The impacts of the two-beam interference heating on the number of core-shell and embedded nanoparticles and on nanostructure coarsening are studied numerically based on the non-linear dynamical model for dewetting of the pulsed-laser irradiated, thin (< 20 nm) metallic bilayers. The model incorporates thermocapillary forces and disjoining pressures, and assumes dewetting from the optically transparent substrate atop of the reflective support layer, which results in the complicated dependence of light reflectivity and absorption on the thicknesses of the layers. Stabilizing thermocapillary effect is due to the local thickness-dependent, steady- state temperature profile in the liquid, which is derived based on the mean substrate temperature estimated from the elaborate thermal model of transient heating and melting/freezing. Linear stability analysis of the model equations set for Ag/Co bilayer predicts the dewetting length scales in the qualitative agreement with experiment.

Metal Chalcogenide Nanoparticle Gel Networks: Their Formation Mechanism And Application For Novel Material Generation And Heavy Metal Remediation Via Cation Exchange Reactions, Irina Ramona Pala

Wayne State University Dissertations

METAL CHALCOGENIDE NANOPARTICLE GEL NETWORKS: THEIR FROMATION MECHANISM AND APPLICATION FOR NOVEL MATERIAL GENERATION AND HEAVY METAL REMEDIATION VIA CATION EXCHANGE REACTIONS

by

IRINA R. PALA

February 2012

Advisor: Dr. Stephanie L. Brock

Major: Chemistry

Degree: Doctor of Philosophy

The dissertation research is focused on (1) uncovering the mechanism of metal chalcogenide nanoparticle gel formation; (2) extending the cation exchange reaction protocol to zinc sulfide gel networks, with the goal of accessing new aerogel chemistries and understanding the factors that drive the process; and (3) conducting a quantitative analysis of the ability of ZnS aerogels to remove heavy metal ions …

Modified Statistical Dynamical Diffraction Theory : A Novel Metrological Analysis Method For Partially Relaxed And Defective C Doped Si And Sige Heterostructures, Paul Kenneth Shreeman

Legacy Theses & Dissertations (2009 - 2024)

The statistical dynamical diffraction theory, which has been initially developed by late Kato remained in obscurity for many years due to intense and difficult mathematical treatment that proved to be quite challenging to implement and apply. With assistance of many authors in past (including Bushuev, Pavlov, Pungeov, and among the others), it became possible to implement this unique x-ray diffraction theory that combines the kinematical (ideally imperfect) and dynamical (the characteristically perfect diffraction) into a single system of equations controlled by two factors determined by long range order and correlation function within the structure. The first stage is completed by …

Development Of Iii-V P-Mosfets With High-Kappa Gate Stack For Future Cmos Applications, Padmaja Nagaiah

Legacy Theses & Dissertations (2009 - 2024)

As the semiconductor industry approaches the limits of traditional silicon CMOS scaling, non-silicon materials and new device architectures are gradually being introduced to improve Si integrated circuit performance and continue transistor scaling. Recently, the replacement of SiO2 with a high-k material (HfO2) as gate dielectric has essentially removed one of the biggest advantages of Si as channel material. As a result, alternate high mobility materials are being considered to replace Si in the channel to achieve higher drive currents and switching speeds. III-V materials in particular have become of great interest as channel materials, owing to their superior electron transport …

Experimental And Theoretical Analysis Of Strain Engineered Aluminium Nitride On Silicon For High Quality Aluminium(X)Indium(Y)Gallium(1-X-Y)Nitride Epitaxy, Mihir Hemant Tungare

Legacy Theses & Dissertations (2009 - 2024)

III-Nitrides on Si are of great technological importance due to the availability of large area, epi ready Si substrates and the ability to heterointegrate with mature silicon micro and nanoelectronics. The major roadblock with realizing this is the large difference in thermal expansion coefficients and lattice constants between the two material systems. A novel technique developed in our research lab shows the potential of simultaneous and substantial reduction in dislocation and crack density in GaN on Si (111). Research undertaken in the current doctoral dissertation, validates the superior GaN quality on Si obtained using our technique and determines the factors …

A Novel Fabrication Technique For Three-Dimensional Nanostructures, Ravi Kiran Bonam

Legacy Theses & Dissertations (2009 - 2024)

Three dimensional micro- and nano-structures are commonly used in the field of Photonics, Optoelectronics, Sensors and Biological applications. Although numerous physical models are developed, a major challenge has been in their fabrication which is commonly limited to conventional layer-by-layer techniques. In this dissertation, a novel method for fabricating three dimensional structures using Electron Beam Lithography (EBL) will be presented.

Materials Engineering For Near-Infrared Light Emission From Silicon Compatible Mos Structures, Himani Suhag Kamineni

Legacy Theses & Dissertations (2009 - 2024)

Silicon-based photonics requires several components, such as a light source, an amplifier/waveguide to transfer the signal, and a photodetector to detect the signal. The motivation for using these silicon-based technologies in photonics applications is two-fold: economic advantages offered by the compatibility with mature silicon IC manufacturing and its excellent material properties for photonic devices (high thermal conductivity, high optical damage threshold, etc.). One of the major challenges in the realization of this technology is the Si-based light source. Because of its indirect bandgap, silicon has very inefficient band-to-band radiative electron-hole recombination. To overcome this obstacle, tremendous research efforts have been …

Cryogenic Machining And Burnishing Of Az31b Magnesium Alloy For Enhanced Surface Integrity And Functional Performance, Zhengwen Pu

Theses and Dissertations--Mechanical and Aerospace Engineering

Surface integrity of manufactured components has a critical impact on their functional performance. Magnesium alloys are lightweight materials used in the transportation industry and are also emerging as a potential material for biodegradable medical implants. However, the unsatisfactory corrosion performance of Mg alloys limits their application to a great extent. Surface integrity factors, such as grain size, crystallographic orientation and residual stress, have been proved to remarkably influence the functional performance of magnesium alloys, including corrosion resistance, wear resistance and fatigue life.

In this dissertation, the influence of machining conditions, including dry and cryogenic cooling (liquid nitrogen was sprayed to …

Novel Design Of Functionalized Carbon Nanotube Electrodes And Membranes For Fuel Cells And Energy Storage, Xin Su

Theses and Dissertations--Chemical and Materials Engineering

A novel electrochemical method to generate nm-scale bubbles at the tips of CNTs can temporarily block the membrane. A 92% blocking efficiency is achieved when the bubbles are stabilized in 30-60 nm diameter „wells‟ at the tips of CNTs. This well is formed by the electrochemical oxidation of the conductive CNTs partially into the polymer matrix of the membrane. Meanwhile, the nanoscale bubbles can be removed with 0.004 atm pressure to recover the transport through the CNT membrane. The CNT membrane with nanoscale bubble valve system was used to demonstrate electrochemical energy storage.

Uniform ultrathin Pt films were electrodeposited onto …

Nanoparticle Additives For Multiphase Systems: Synthesis, Formulation And Characterization, Vinod Kanniah

Theses and Dissertations--Chemical and Materials Engineering

Study on nanoparticle additives in multiphase systems (liquid, polymer) are of immense interest in developing new product applications. Critical challenges for nanoparticle additives include their synthesis, formulation and characterization. These challenges are addressed in three application areas: nanofluids for engine lubrication, ultrathin nanocomposites for optical devices, and nanoparticle size distribution characterization.

Nanoparticle additives in oligomer mixtures can be used to develop extended temperature range motor oils. A model system includes poly(α-olefin) based oligomers with a modest fraction of poly(dimethylsiloxane) oligomers along with graphite as nanoparticle additive. Partition coefficients of each oligomer are determined since the oligomer mixture phase separated at …

Finite Element Analysis Of The Contact Deformation Of Piezoelectric Materials, Ming Liu

Theses and Dissertations--Chemical and Materials Engineering

Piezoelectric materials in the forms of both bulk and thin-film have been widely used as actuators and sensors due to their electromechanical coupling. The characterization of piezoelectric materials plays an important role in determining device performance and reliability. Instrumented indentation is a promising method for probing mechanical as well as electrical properties of piezoelectric materials.

The use of instrumented indentation to characterize the properties of piezoelectric materials requires analytical relations. Finite element methods are used to analyze the indentation of piezoelectric materials under different mechanical and electrical boundary conditions.

For indentation of a piezoelectric half space, a three-dimensional finite element …

Development Of Nanocomposites For Energy Storage Devices, Md Ashiqur Rahaman Khan

Open Access Theses & Dissertations

With the ever-increasing need in improving the performance and operation life of future mobile devices, developing higher power density energy storage devices has been receiving more attention. Lithium ion battery (LIB) and capacitor are two of the most widely used energy storage devices and have attracted increasing interest from both industrial and academic fields. Batteries have higher power density than capacitor but significantly longer charge/discharge rates. In order to further improve the performance of these energy storage devices, one of the approaches is to use high specific surface area nano-materials. Among all the nano-materials developed so far, one-dimensional nanowires are …

Development Of Advanced Polymer Nanocomposite Capacitors, Miguel Mendoza

Open Access Theses & Dissertations

The current development of modern electronics has driven the need for new series of energy storage devices with higher energy density and faster charge/discharge rate. Batteries and capacitors are two of the most widely used energy storage devices. Compared with batteries, capacitors have higher power density and significant higher charge/discharge rate. Therefore, high energy density capacitors play a significant role in modern electronic devices, power applications, space flight technologies, hybrid electric vehicles, portable defibrillators, and pulse power applications. Dielectric film capacitors represent an exceptional alternative for developing high energy density capacitors due to their high dielectric constants, outstanding breakdown voltages, …

Growth And Characterization Of Functional Nanoparticulate Films By A Microwave Plasma-Assisted Spray Deposition Process, Ted Wangensteen

USF Tampa Graduate Theses and Dissertations

Nanoparticle and nanoparticulate films have been grown by a unique approach combining a microwave and nebulized droplets where the concentration and thus the resulting particle size can be controlled. The goal of such a scalable approach was to achieve it with the least number of steps, and without using expensive high purity chemicals or the precautions necessary to work with such chemicals. This approach was developed as a result of first using a laser unsuccessfully to achieve the desired films and particles. Some problems with the laser approach for growing desired films were solved by substituting the higher energy microwave …