Materials Science and Engineering Commons^™

Corrosion Case Study On Pipeline, Kangze Ren

Corrosion Research

The Kashagan pipeline leaks were likely caused by sulfur stress corrosion cracking, a combined corrosion mechanism developed by the presence of high pressure, the high level of hydrogen sulfide(the main "ingredient" of sour gas), and poor metallurgical choice. Improper welding and poor metallurgical examination were blamed for causing the leaking issue. The purpose of the current review is to raise the alarm about the inappropriate corrosion management of Kashagan oil production and its societal and environmental consequences.

Machine Learning Prediction Of Hea Properties, Nicholas J. Beaver, Nathaniel Melisso, Travis Murphy

College of Engineering Summer Undergraduate Research Program

High-entropy alloys (HEA) are a very new development in the field of metallurgical materials. They are made up of multiple principle atoms unlike traditional alloys, which contributes to their high configurational entropy. The microstructure and properties of HEAs are are not well predicted with the models developed for more common engineering alloys, and there is not enough data available on HEAs to fully represent the complex behavior of these alloys. To that end, we explore how the use of machine learning models can be used to model the complex, high dimensional behavior in the HEA composition space. Based on our …

Study Of All-Group-Iv Sigesn Mid-Ir Lasers With Dual Wavelength Emission, Grey Abernathy, Solomon Ojo, Abdulla Said, Joshua M. Grant, Yiyin Zhou, Hryhorii Stanchu, Wei Du, Baohua Li, Shui-Qing Yu

Electrical Engineering Faculty Publications and Presentations

Direct band gap GeSn alloys have recently emerged as promising lasing source materials for monolithic integration on Si substrate. In this work, optically pumped mid-infrared GeSn lasers were studied with the observation of dual-wavelength lasing at 2187 nm and 2460 nm. Two simultaneous lasing regions include a GeSn buffer layer (bulk) and a SiGeSn/GeSn multiple quantum well structure that were grown seamlessly using a chemical vapor deposition reactor. The onset of dual lasing occurs at 420 kW/cm². The wider bandgap SiGeSn partitioning barrier enables the independent operation of two gain regions. While the better performance device in terms …

Optimizing Mn-Al Permanent Magnet Performance Through Control Of The Phase Transformation, Ternary Element Addition, And Advanced Processing, Thomas R. Keller

Dartmouth College Ph.D Dissertations

The growing need for electrical power in machines and vehicles brings with it a growing need for critical materials. The current high-performance permanent magnets (PMs) based on rare-earth (RE) elements Nd and Sm cannot escape the problem of raw material cost, geographic scarcity in the earth’s crust, and lack of circular global supply chains. This poses a problem of industrial ecology: can PMs be made from inexpensive, more abundant materials while still meeting sufficient performance criteria? PMs based on the magnetic τ phase of Mn-Al offer a possible alternative to REPMs. However, years of innovation have not yet achieved real-world …

Challenges In Optimization For The Performance On Sustainability Dimensions In Reverse Logistics Social Responsibility, Sumarsono Sudarto, Katsuhiko Takahashi, Mochammad Dewo

Makara Journal of Technology

Reverse logistics social responsibility is preferred as the most acceptable solution for addressing the challenges in stakeholders’ debate regarding social responsibility in supply chains because it involves as many actors as possible in the supply chain to perform social responsibility to achieve sustainability. This paper explores the challenges in achieving optimal policies in sustainability dimensions for collection and recycling facilities in reverse logistics. Sustainability dimensions include economic, environmental, and social aspects. The reverse logistics is modeled on System Dynamics, and a simplified statistical analysis using a contour chart is employed in numerical experiments. Results show a narrow area of optimal …

Fatigue And Fracture Of Electron Beam Melting Ti-6al-4v, William A. Grell

Electronic Theses and Dissertations

For applications in the aerospace field, selection of materials for a given design requires an understanding of critical properties, like fatigue and fracture, in addition to static mechanical and physical properties. With the ongoing advancements in metallic additive manufacturing techniques and the interest in applying the process to aerospace applications, there is a clear need to fully characterize properties. Arguably, the most attractive alloy for applications in aerospace is the Ti-6Al-4V alloy. The current dissertation examines the mechanical properties of the alloy, made by the Electron Beam Melting (EBM) Powder Bed Fusion (PBF) method. As illustrated in this work, the …

Effect Of Heat Treatment On The Mechanical And Corrosion Properties Of The Cocrnifeal Heas, Ahmed Korra

Masters Theses and Doctoral Dissertations

High entropy alloys (HEAs) are a relatively new class of metallic materials that have shown great potential for use in extreme environments, such as high temperatures and corrosive conditions. Among the different types of HEAs, CoCrNiFeAl HEAs are potential materials for a wide range of applications, including aerospace, biomedical, and energy storage. This work focused on the effects of heat treatment temperatures from 800 °C to 1100 °C on the microstructure and mechanical properties of these alloys, as well as their electrochemical corrosion behavior. A thermodynamic model was implemented to predict the performance of the material. The results of this …

Calibration Of The Johnson–Cook Model At High Temperatures For An Ultra-High Strength Crnimov Steel, Mario F. Buchely, S. Chakraborty, V. Athavale, Laura Bartlett, Ronald J. O'Malley, D. Field, K. Limmer, K. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a study on the thermo-mechanical behavior of an ultra-high strength CrNiMoV steel at high temperatures and medium strain rates through hot tensile tests. The material was examined in two conditions: as-cast/heat-treated (AC/HT) and as-rolled (AR). Tensile tests were conducted at temperatures of 800,900,1000,1100, and 1200°C, and strain rates of 0.1,1, and 10s−1. Inclusion and porosity analysis was also performed on the tensile specimens. The results revealed that the flow stress decreased by approximately 70% on average from 800°C to 1200°C, while increasing by approximately 32% on average from 0.1s−1 to 10s−1 in strain rate. The elongation exhibited …

Optimization Of Alti Pld Coating By Increasing Ti Content, N2 And Annealing Which Used For Skd61 Pins In Aluminum Die Casting, Rusman Kosasih, Maria Margaretha Suliyanti Prof, Dedi Priadi, Wisnu Usni

Journal of Materials Exploration and Findings

The Alumunium Titanium Nitrogen (AlTiN) coating is known as one of the best coating materials for protective coating, while Pulsed Laser Deposition (PLD) is a laser coating process used for electric layer and superconductor applications, producing thin films up to 20 µm in thickness. The combination of these two matters has already been researched and is still in progress. One major challenge in the aluminium casting industry is to minimize the damage caused to tool steel pins made from SKD61, when aluminium material sticks to the pin, and halting production. Therefore, research on effective coatings for tool steels and testing …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario Buchely, Ronald O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the face-centered cubic (FCC) multi-principal element alloys (MPEAs) developed thus far contain cobalt. for many applications, it is either required or beneficial to avoid cobalt, since cobalt has long-term activation issue (for nuclear applications), is expensive, and is considered a critical material. in addition, FCC structured solid-solution MPEAs tend to have relatively low strength. an FCC solid-solution Fe30Ni30Mn30Cr10 (at %) MPEA was fabricated via arc melting, followed by homogenization at 1100 °C for 12 h. the alloy was hot rolled at 1100 °C with a total reduction of up to 97 %. the microstructure was characterized, and mechanical …

Engineering Heterogeneous Nucleation During Solidification Of Multiphase Cast Alloys: An Overview, Simon (Semen) N. Lekakh, Jingjing Qing

Materials Science and Engineering Faculty Research & Creative Works

The theory of heterogeneous nucleation was initially developed as a part of condensed matter physics, and later it was used as an important engineering tool to design metallurgical processes. This success has led to wide applications of the theory in metallurgical practice. For example, engineering heterogeneous nucleation in ductile iron has been used to reduce shrinkage defects, suppress cementite formation, and modify the size and shape of microstructural constituencies. This demonstrates how theoretical knowledge could benefit industry practice. This overview aims to summarize the authors' published studies in co-authorship with colleagues and students, which covers different aspects of engineering heterogeneous …

Nonmonotonic Effect Of Chemical Heterogeneity On Interfacial Crack Growth At High-Angle Grain Boundaries In Fe-Ni-Cr Alloys, Yuchu Wang, Bita Ghaffari, Christopher Taylor, Simon Lekakh, Carlos Engler-Pinto, Larry Godlewski, Yang Huo, Mei Li, Yue Fan

Electrical and Computer Engineering Faculty Research & Creative Works

An intermittent pattern is observed in the modeling of interfacial cyclic-loading crack growth at high-angle grain boundaries in ternary Fe-Ni-Cr alloys. Different from conventional wisdom of stress-intensity factor, the abrupt crack advances are found driven by extreme value statistics - namely, the aggregation of atoms with most compressive residual stresses. In addition, inherently non-affine atomic stress fluctuations are discovered, and the fluctuations peak at intermediate level of chemical heterogeneity, causing the fastest crack growth. Implications of such nonmonotonic mechanism in regard to the origin of intermediate-temperature embrittlement phenomena are also discussed.

Improving The Tensile Mechanical Properties Of Direct Energy Deposited (Ded) Inconel 718 Aircraft Components Using A Standard Heat Treatment, Spencer Vincent Flynn

Materials Engineering

This project aimed to improve the mechanical properties of as-printed additively manufactured Inconel 718 samples using a heat treatment usually used for cast and wrought Inconel 718. The mechanical properties sought to be optimized were yield strength, ultimate tensile strength, elongation, and reduction in area. The property goals were to match or exceed those of cast and heat treated Inconel 718. Wire-fed electron beam direct energy deposition (DED) was used to manufacture the samples, which were then heat treated using the AMS 5663 standard in an inert atmosphere. The samples were then tested in tension to obtain data on their …

Failure Analysis Of Variably Sized 4340 Steel Mandrels Utilized In The Production Of Seamless Superalloy Rings Through The Vertical Ring Rolling Process, Mikhail Alexeyevich Vasilyev, Joshua Brady Venz

Materials Engineering

Vertical ring rolling is a forging process which forms seamless metal rings through applying a large force at elevated temperatures onto component materials stabilized by cylindrical mandrels. Carlton Forge Works, a company which produces rings of superalloy materials such as INCO718 and 718Plus, is experiencing a consistent failure of mandrels due to extreme conditions. An analysis of the lifetime (bulk material, heat treatment, and use) was performed, which aided in the identification of process variables tied to mandrel failure. Experiments were formed surrounding three variables of the mandrel heat treatment: Austenitization temperature, quenching temperature, and tempering conditions, with the goal …

Investigation Into Oxygen Diffusion As It Relates To Alpha Case Formation In Ti-6al-4v Based On Different Forging Thermal Cycles, Tyler J. Meador, Jon Leduc, Francesca Hope

Materials Engineering

An investigation into the growth kinetics of alpha case in Ti-6Al-4V in the presence of oxygen was conducted for different forging thermal cycles. This was done to determine whether the alpha case should be removed after each thermal cycle or as the final step after forging. The thermal cycles consisted of four hours at 1750 °F. Samples were subjected to this treatment one, two, three, and four times along with a continuous sixteen hour hold. Four cycle and Hold samples were subjected to an additional thermal cycle above the beta transus at 1925 °F. These then went through a final …

Effect Of Cr And Ni Concentrations On Resilience Of Cast Nb-Alloyed Heat Resistant Austenitic Steels At Extreme High Temperatures, Simon N. Lekakh, Mario F. Buchely, Mei Li, Larry Godlewski

Materials Science and Engineering Faculty Research & Creative Works

Austenitic Cr–Ni Alloyed Heat Resistant Steels with Nb Additions Are Used for Intensively Thermo-Mechanically Loaded Cast Components Working in Extreme High Temperature Oxidizing Environment. their Performance during Static Oxidation and Transient Thermo-Mechanical Loading Was Investigated to Recommend an Optimal Cost-Effective Cr/Ni Composition of Nb-Alloyed Austenitic Class Steels. the Static Oxidation and Transient Thermo-Mechanical Behavior of Three Austenitic Steels with Different Cr/Ni Alloying Levels Were Investigated and Compared for Variety of Working Conditions. Static Oxidation Was Performed between 900 °C and 1000 °C in Air for 400 H. the Critical Temperature Which Increases Spallation during Static Oxidation Was Determined for Each …

Machinability Of High Mn Steel Using Tool Life Criteria, Dika Handayani, Victor F. Okhuysen, Nicole Wagner

Engineering Faculty Articles and Research

High Mn steel alloys have shown to provide both high strength and ductility. However, current literature offers limited guidance on the machinability of these steel alloys. Therefore, this work provides turning recommendations for high Mn steel that is based on tool life data. Several indexable carbide inserts with various rake angles were used to machine cast billets of high Mn steel. Turning characteristics from various feed rates, cutting speeds, and depths of cut were analyzed. Through a design of experiments, it was determined that the feed rate was the most significant factor affecting tool life and that a tool with …

Development Of Dynamic Risk-Based Inspection Using Forward Difference Approach For Pipe Failure Due To Uniform Corrosion, Jaka Fajar Fatriansyah, Zahra Nadia Nurullia, Andreas Federico, Dedi Priadi

Journal of Materials Exploration and Findings

The oil and gas industry is one of the world's largest and most influential energy contributors. All aspects involved in the operation of this industry are fundamental to be reviewed and managed correctly, especially by preventing or minimizing the failures that could occur. Uniform corrosion is the most common component failure mechanism that can cause failure in the oil and gas industry. The company's actions in managing and preventing the risk of this type of failure have a major role in the sustainability of the company due to the possibility of more significant impacts if the risk cannot be handled …

Mesoscale Modeling And Machine Learning Studies Of Grain Boundary Segregation In Metallic Alloys, Malek Alkayyali

All Dissertations

Nearly all structural and functional materials are polycrystalline alloys; they are composed of differently oriented crystalline grains that are joined at internal interfaces termed grain boundaries (GBs). It is well accepted that GB dynamics play a critical role in many phenomena during materials processing or under operating environments. Of particular interest are GB migration and grain growth processes, as they influence many crystal-size dependent properties, such as mechanical strength and electrical conductivity.

In metallic alloys, GBs offer a plethora of preferential atomic sites for alloying elements to occupy. Indeed, recent experimental studies employing in-situ microscopy revealed strong GB solute segregation …

Point Heat Source Correlation To Microstructural Evolution In Advanced Manufacturing, Mark Anderson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Although there are different ways that advanced manufacturing can be performed, the use of single-point heat sources has become the standard to control a final product’s properties. It is imperative to understand how the heat source used in the different advanced manufacturing processes affect the microstructure of interest. The intimate relationship between the heat source and microstructure allows for controlling and tailoring a part’s properties. Utilizing different microstructural analysis, the cross-correlation of various point heat sources to developed microstructure was conducted in this dissertation.

Laser powder bed fusion allows for unique print-to-part protocols, but the dynamics of the process makes …

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

A Guide To Fifty Years Of Research At Montana Tech: Part 2 The Treatment Of Electroplating And Electromachining Metal Hydroxide Sludge For The Recovery Of Metal Values [See Also Part 1), Larry G. Twidwell

Metallurgy

ABSTRACT and FORWARD

The treatment and recovery of metal species from hydrometallurgical solutions and wastewater solids has been and continues to be an important research topic. This presentation includes a guide to the literature with a summary discussion of the research conducted at Montana Tech in the Department of Metallurgical and Materials Engineering during the 1984-2001 period. A previous presentation (Part 1) focused on the removal of arsenic, selenium, and other species by hydrometallurgical processes and the formation of environmentally stable disposable products. This guide is available at the reference presented above.

This following presentation (Part 2) is based on …

A Guide To Fifty Years Of Research At Montana Tech: Part 1-The Treatment Of Arsenic, Selenium, Thallium, Metal Bearing Solutions And Waste Solids, Larry G. Twidwell

Metallurgy

ABSTRACT and FORWARD

The removal of arsenic, selenium, and metal species from hydrometallurgical solutions and wastewaters has been and continues to be an important research topic. This presentation includes a discussion of the research conducted at Montana Tech in the Department of Metallurgical and Materials Engineering during the past fifty years. The discussion is focused on removal of arsenic by co-precipitation with Fe(III) and Fe(II), co-precipitation with Fe(III) and Al(III), reduction using elemental iron; the removal of selenium by elemental iron and catalysed iron; and the removal of cadmium, copper, nickel, zinc by co-precipitation with Fe(III) and Al(III).

This presentation …

Effects Of Tempering Temperature On Gas Turbine Fan Cases, Seth Utter

Honors Scholar Theses

The project aimed to investigate the effects of tempering temperature on metals used for gas turbine engine fan cases as a major relevant concern is containing blades in during blade-out events. There are three ways to accomplish this: using a thicker metal, incorporating different materials into the case, or heat treating the metal. This project focused on the third solution: reviewing the impact toughness and hardness of fractured samples and their equivalent ductile-to-brittle transition shear faces. Given its availability, 1045 steel, as opposed to aerospace grade metals, was used for in-house testing. The data obtained from these experiments were then …

Mechanical Characterization Of Additively Manufactured Alloys Compared To Their Wrought Counterparts, Laith A. Alqawasmi

Mechanical Engineering ETDs

Additive manufacturing is a method of manufacturing based on building parts layer by layer, allowing for more control over shape of the product, therefore reducing machining costs, reducing material waste, faster production times and the ability to build complex engineering design that other manufacturing technologies won’t be able to produce. This research is on the tensile and indentation testing (following ASME standards) of 3D printed Ti-6Al-4V and Inconel 718 built by powder-based direct energy deposition technology. Ti-6Al-4V is an attractive material for the aerospace and aviation industry, and Inconel 718, a nickel-chromium based superalloy, is an attractive material for usage …

A High-Strength Precipitation Hardened Cobalt-Free High-Entropy Alloy, Matthew Luebbe, Jiaqi Duan, Fan Zhang, Jonathan Poplawsky, Hans Pommeranke, Maalavan Arivu, Andrew Hoffman, Mario Buchely, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. a Co-free (Fe0.3Ni0.3Mn0.3Cr0.1)88Ti4Al8 HEA was developed and studied in this work. in contrast to previous Co-free HEAs, this alloy is close to Equi atomic in its composition and promises a more …

Timeline - History Of The Metallurgy / Mineral Processing Programs (1900-2022), Jerome Downey, Larry G. Twidwell

Metallurgy

No abstract provided.

History Of The Metallurgy / Mineral Processing Programs (1900-2022), Jerome Downey, Larry G. Twidwell

Metallurgy

No abstract provided.

Treatment Of Arsenic-Bearing Minerals And Fixation Of Recovered Arsenic Products: An Updated Review, Larry G. Twidwell

Metallurgy

Mineral processing and extractive metallurgical operations have created and are creating appreciable arsenic bearing wastewater and waste solid products that have to be handled, treated for recycle, or treated for environmentally safe disposal. At present there are intense research and operational activities being conducted to provide the best viable processing procedures to ensure that the mineral processing and extractive metallurgical industries are profitable and environmentally secure. The focus of this presentation is on the element arsenic, even though many other deleterious elements may also be present in ores and concentrates. Numerous base metal resources contain arsenic bearing minerals, especially resources …

Physics-Based Crystal Plasticity Model For Predicting Microstructure Evolution And Dislocation Densities, Juyoung Jeong

LSU Doctoral Dissertations

This work presents three different studies investigating plastic deformation mechanisms in metals and alloys using crystal plasticity finite element (CPFE) modeling. The first study presents a new nonlocal crystal plasticity model for face-centered cubic single crystals under heterogeneous inelastic deformation. The model incorporates generalized constitutive relations that incorporate the thermally activated and drag mechanisms to cover different kinetics of viscoplastic flow in metals and describes the plastic flow and yielding of single-crystals using dislocation densities. The model is compared to micropillar compression experiments for copper single crystals and clarifies the complex microstructural evolution of dislocation densities in metals. The second …