Materials Science and Engineering Commons^™

F-Temper Vs O-Temper Brazing Of 3003 Aluminum Return Bends, Mieka R. Clark

Dissertations, Master's Theses and Master's Reports

As-extruded (F-temper) 3003 return bends can provide cost savings over annealed (O-temper) return bends in aluminum heat exchangers. To assess if F-temper return bends are an alternative to the baseline O-temper bends, the grain structure, bending performance, and melting behavior were assessed through:

• Quantifying the effect of dispersoids on recrystallization
• Tracking bending behavior through grain morphology and surface texture
• Measuring the number and volume fraction of the α-Al(Mn,Fe)Si intermetallic
• Inducing incipient melting through high temperature thermal exposure.

When homogenized at 620°C and 630°C, the F-temper bends had no orange peel texture, the grain size was equivalent to the annealed product, …

Improving Cast Steel Rail Coupler Fatigue Resistance Through Local Wire-Arc Additive Manufacturing, Andrew M. Bunge

Dissertations, Master's Theses and Master's Reports

Every year, thousands of cast-steel railcar couplers suffer from corrosion-initiated fatigue cracking in similar areas of the coupler’s knuckle; between 2015 and 2018 about 90,000 knuckles were replaced, otherwise these couplers would have been at risk for unexpected failures. These types of couplers have been common in industrial use as early as 1932, hence it is desirable for a countermeasure to the fatigue cracking that does not involve significantly altering the geometry or casting process. Wire arc additive manufacturing (WAM) is a developing technology which boasts the ability to produce complex near-net-shape components; however, less attention has been paid to …

High Temperature Strength Reduces Soldering In Aluminum High Pressure Die Casting, Jacob A. Belke

Dissertations, Master's Theses and Master's Reports

Die soldering, an adhesion defect in high pressure die casting (HPDC), is a symptom of localized sticking where a localized portion of the cast material is adhered to the tooling surface causing build up over time. This requires the tooling to be serviced which incurs additional costs to the process that gets passed on to the parts. Historically, soldering has been mitigated using lubricants, coatings, and alloy chemistry modifications but solder persists.

The Tresca friction thermomechanical model suggests soldering occurs when the local interfacial shear stress between the casting and die surface exceeds the local shear strength of the casting. …

Parametric Optimization Of Friction Stir Welding Of Aa6061-T6 Samples Using The Copper Donor Stir-Assisted Material Method, Aiman H. Al-Allaq, Joseph Maniscalco, Srinivasa Naik Bhukya, Zhenhua Wu, Abdelmageed Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

This study presents an optimization of the process parameters for the effect of copper (Cu) donor material percentage on the friction stir welding (FSW) of AA6061-T6 alloy. Extensive factorial experiments were conducted to determine the significance of the rotational speed (ω), the transverse speed (v), the interface coefficient of friction (μ), and the Cu donor material percentage in the plunge, left, right, and downstream zones. Design Expert 13 software was used to identify the number of simulation experiments to be conducted using the Abaqus simulation software. From Design Expert 13, which is a thorough multi-objective optimization analysis software, we were …

A Review On Biochar As An Adsorbent For Pb(Ii) Removal From Water, Pushpita Kumkum, Sandeep Kumar

Civil & Environmental Engineering Faculty Publications

Heavy metal contamination in drinking water is a growing concern due to its severe health effects on humans. Among the many metals, lead (Pb), which is a toxic and harmful element, has the most widespread global distribution. Pb pollution is a major problem of water pollution in developing countries and nations. The most common sources of lead in drinking water are lead pipes, faucets, and plumbing fixtures. Adsorption is the most efficient method for metal removal, and activated carbon has been used widely in many applications as an effective adsorbent, but its high production costs have created the necessity for …

Mechanisms Of Dendritic Shorting In Lithium Metal Batteries With Li7la3zr2o12 Solid Electrolytes, Lukas Karapin-Springorum

Pomona Senior Theses

Energy storage will play a crucial role in efforts to mitigate the effects of climate change caused by greenhouse gas emissions from human activity. Lithium metal batteries using solid electrolytes like Li₇La₃Zr₂O₁₂ have higher energy density than lithium-ion batteries, which may enable a more rapid and complete electrification of transportation. However, lithium metal batteries suffer from undesirable short-circuiting when metallic lithium deposits connect the two electrodes. It has been debated whether these lithium dendrites generally grow directionally from the anode or are generated by the reduction of lithium ions inside the solid electrolyte, …

B(C₆F₅)₃ Co-Catalyst Promotes Unconventional Halide Abstraction From Grubbs I To Enhance Reactivity And Limit Decomposition, Austin W. Medley, Diya Patel, Calvin Utne, Trandon A. Bender

Chemistry & Biochemistry Faculty Publications

Ruthenium based Grubbs metathesis has become a commonplace reaction for synthetic chemists. Development of new generations of catalysts evolving from Grubbs I (GI) have led to greater stability, functional group compatibility, and superior reactivities. However, these advancements lead to increased costs. To this end, we report here how the addition of the commercially available tris(pentafluorophenyl)borane Lewis acid, which has become a common place catalyst in its own right, leads to enhanced reactivity of GI. Moreover, the increased reactivity arises via halide abstraction rather than traditional phosphine dissociation, providing ring-opening metathesis polymerization products that are divergent from those synthesized without the …

Calculation Of Elastic Constants Of Bulk Metallic Glasses From Indentation Tests, Zhitong Xu, Ming Liu, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

One of the challenges in the applications of instrumented indentation is to simultaneously measure elastic modulus and Poisson’s ratio of homogeneous, isotropic materials. This work proposes empirical equations for simultaneous calculation of elastic modulus and Poisson’s ratio of bulk metallic glasses (BMGs) from the ratio of the short diagonal length to the long diagonal length and the area of the Knoop imprint. The parameters pre- sented in the empirical equations are determined first by Knoop microhardness tests of 24 BMGs, whose elastic moduli and Poisson’s ratios are measured by resonant ultrasound spectroscopy. These empirical equations are further validated by the …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. the end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Effects Of Ac Interference On Pipelines Under Cathodic Protection And Cathodic Disbondment Of Pipeline Coatings, Tanner Laughorn

Williams Honors College, Honors Research Projects

This project is split into two parts. The first revolves around AC interference on pipeline steel under cathodic protection. The corrosion rate of steel samples will be measured after they are exposed to varying levels of AC interference and cathodic protection. The results will be used to help develop new guidelines for appropriate cathodic protection of steel pipelines. The second part of this project revolves around the cathodic disbondment of pipeline coatings while under cathodic protection. The disbondment distance, electrolyte pH, and electrochemical impedance spectroscopy will be tested for multiple industry standard coatings under various conditions. The results will be …

Causational Analysis And Rectification Of Issues Concerning Scale Formation On Hot-Rolled Straight Bar Product And Its Effects On Ultrasonic Testing, Riley Mattix

Williams Honors College, Honors Research Projects

At Charter Steel's NDT Processing Plant located in Cleveland, Ohio, a concern has arisen regarding the recently implemented bar straightening and UT (Ultrasonic Testing) equipment. A substantial amount of mill scale, which is typically removed during the straightening process, is persisting on the bar’s surface throughout most of the NDT procedure. This lingering scale has been observed to flake off once inside the UT equipment, introducing unwanted noise and phantom peaks into the UT readings. Additionally, thick mill scale has been identified as a source of background interference in the received data. In contrast, bars that have been subjected to …

Corrosion Inhibitors: Mitigating The Degradation Of Rebar, Jake R. Hughes

Williams Honors College, Honors Research Projects

Our conjecture was twofold: first, that two compounds historically used as food preservatives could act as environmentally friendly inhibitors against rebar corrosion, and second, that molecular properties have a quantifiable influence on inhibition efficiency (%IE). To evaluate the two compounds, cyclic potentiodynamic polarization was used to determine corrosion current density (i_corr) and %IE. The “green” inhibitor candidates included sodium metabisulfite and ascorbic acid, which yielded maximum %IE values of -123900% and 91%, respectively. Results indicated that sodium metabisulfite is not a suitable inhibitor, while ascorbic acid showed potential to extend reinforced concrete’s design life without posing health or …

Application Of Conductivity Techniques For Interlayer Discontinuity Detection In Additively Manufactured Metal Materials, Joshua D. Newell, Riley R. Myers

Williams Honors College, Honors Research Projects

Additive manufacturing is becoming increasingly more popular and efficient. One drawback is the possibility of interlayer discontinuities forming in the material. A non-destructive technique utilizing the changing resistivity of the material as discontinuities appear was used to detect those discontinuities and was verified through additional testing of manually added through-thickness discontinuities. This technique has been proven to be useful in understanding fatigue crack growth of conventional metal and composite structures. Experimental investigation of fatigue in steel with an edge notch has been performed using these techniques to understand source and location of crack formation and growth in conventional material. Application …

Using Tensile And Compressive Stress Superposition During Incremental Forming To Manipulate Martensitic Transformation In Ss304, Elizabeth M. Mamros, Fabian Maaß, A. Erman Tekkaya, Brad L. Kinsey, Jinjin Ha

Faculty Conference Papers and Presentations

Single point incremental forming (SPIF) is a flexible manufacturing process that has applications in industries ranging from biomedical to automotive. In addition to rapid prototyping, which requires easy adaptations in geometry or material for design changes, control of the final part properties is desired. One strategy that can be implemented is stress superposition, which is the application of additional stresses during an existing manufacturing process. Tensile and compressive stresses applied during SPIF showed significant effects on the resulting microstructure in stainless steel 304 truncated square pyramids. Specifically, the amount of martensitic transformation was increased through stress superposed incremental forming. Finite …

Experimental Investigation Of Liquid Metal Embrittlement In Hot-Dip Galvanized Structural Steel, Amelia Mcnamee

College of Graduate Studies: Theses & Dissertations

This research investigated the liquid metal embrittlement (LME) of hot-dipped galvanized structural steel. The relationship between stress and failure time was analyzed to evaluate the potential presence of a critical stress threshold beyond which LME may occur. A testing apparatus to induce axial stress was designed and assembled in-house. A36 low carbon steel was tested in this study. Different deadweight loadings were applied to the testing sample along the axial direction. The test temperature was maintained by a programmable furnace while the sample gauge section was submerged in a molten zinc bath. Failure time and total displacement of the steel …

Effects Of Additions On The Microstructure, Macrostructure, And Mechanical Properties Of Gray Iron, Evan J. Carter

College of Graduate Studies: Theses & Dissertations

The iron matrix is a major component of the gray iron (GI) microstructure, which is the transformation product of austenite during solidification. It is generally accepted that the structure of the austenite will impact the final grain structure and thus the properties of GI. Refinement of the austenite grain structure has the potential to increase the strength of GI. Knowledge of controlling austenite grain size with common alloy additions in GI is very limited and is investigated in this research. Utilizing the DAAS heat treatment process, the austenite grain boundaries can be retained and observed directly. The observations were correlated …

Thermomechanical Process Simulation And Quantification Of Nanoscale Precipitation Influencing Ductility And Strength During Alloy Processing, Alyssa Stubbers

Theses and Dissertations--Chemical and Materials Engineering

Experimental process simulation and quantification of microstructure development during processing are challenging due to limitations with machinery temperature capability, inadequate resolution and sampling volume of currently available characterization techniques, and difficulty characterizing material microstructures as close to processing-relevant conditions as possible. This dissertation addresses how process simulation can be performed using Gleeble thermomechanical technologies and how microstructure development during these processing simulations can be quantified both in-situ and ex-situ.

The first portion of this dissertation demonstrates how Gleeble technologies can be applied to simulate complex material processing conditions in order to produce process-property profiles that can be used to inform …

Nickel Superalloy Composition And Process Optimization For Weldability, Cost, And Strength, Sophie A. Mehl

Dissertations, Master's Theses and Master's Reports

To advance sustainability efforts, electric power plants have reduced specific carbon dioxide emissions by increasing operating temperatures and pressures to improve power generation efficiency. The latest improvements are utilized in advanced ultra-supercritical power generation. To meet these operating conditions, nickel superalloys are used in the highest temperature components; however, they are expensive and present weldability challenges. This project aims to experimentally optimize a nickel superalloy to improve material weldability and decrease cost without compromising strength. Three optimized compositions were developed, and their microstructures and mechanical properties were compared to Nimonic 263, a common nickel superalloy in electric power plants. The …

Anaerobic Reductive Bioleaching Of Manganese Ores, Neha Sharma

Dissertations, Master's Theses and Master's Reports

Manganese extraction by biological methods is a green and economical way to produce manganese from low as well as high grade manganese ores. This is especially important for US ores, which are primarily either small in extent, low-grade with a high iron content, or both. They are therefore not suitable for conventional mining, which is very capital-intensive and requires a large up-front investment and are therefore imported at high costs. The goal is therefore to develop a process that can be applied at small scales, with minimal startup costs, and low equipment and labor requirements. It is also critical to …

Fatigue Resistant Cast Steel Railcar Couplers Produced By Wire-Arc Additive Manufacturing (Waam), Samuel Vellequette

Dissertations, Master's Theses and Master's Reports

Every year, approximately 90,000 cast steel railcar coupler knuckles are replaced preemptively to avoid fatigue failure. The coupler geometry has been in service since the early 1930s, so geometry changes are restricted to maintain compatibility with the existing fleet. Defects from the casting process, decarburization during heat treatment, and in-service exposure to corrosive environments combine to promote fatigue crack nucleation in high-stress regions of the knuckle. Wire-arc additive manufacturing (WAAM), which uses traditional welding techniques to build material to near-net shapes, was employed to deposit higher-strength materials in critical regions. By replacing the cast steel in the high-stress region of …

Processing Of Niti Sma For High Reflectivity Applications, Nicholas Dean Asbury

UNF Graduate Theses and Dissertations

Nickel Titanium (NiTi) is a shape memory alloy (SMA) that is capable of being deformed and subsequently returned to the original shape through heating. This unique property makes NiTi a prime material for potential applications in the aerospace industry. As manufacturing capabilities advance, the ability to produce and implement advanced materials, such as shape memory alloys like NiTi, becomes more feasible. One such application being studied is deployable mirrors for imaging satellites. Reflector and mirror surfaces for imaging in the visible and infra-red range of the light spectrum require low surface roughness across the largest allowable area for the collection …

การศึกษาผลของอุณหภูมิอบอ่อนและความเร็วในการรีดต่อโครงสร้างจุลภาคและสมบัติเชิงกลของเหล็กกล้ารูปพรรณรีดร้อนเกรด S450j0, เชิญจุติ อรุณถิน

Chulalongkorn University Theses and Dissertations (Chula ETD)

งานวิจัยนี้ศึกษาผลกระทบของอุณหภูมิการอบอ่อนและความเร็วการรีดต่อโครงสร้างจุลภาค สมบัติเชิงกล และคุณภาพผิวของเหล็กกล้าโครงสร้าง S450J0 ชนิดรีดร้อน โดยมุ่งเน้นกระบวนการผลิตเหล็กกล้าเอชบีมขนาด 305x305x223 กก./ม. การทดลองใช้อุณหภูมิการอบอ่อนและความเร็วการรีดที่แตกต่างกันเพื่อตรวจสอบผลกระทบต่อคุณภาพของผลิตภัณฑ์ ผลการทดลองแสดงให้เห็นว่า อุณหภูมิการอบอ่อนมีอิทธิพลอย่างมีนัยสำคัญต่อสมบัติเชิงกล โดยอุณหภูมิที่สูงขึ้นจะเพิ่มค่าความต้านทานแรงดึงที่จุดครากและความต้านแรงดึง แต่ส่งผลให้ค่าความเหนียวและความแกร่งลดลงในบางกรณี ในทางตรงกันข้าม ความเร็วการรีดที่แตกต่างกันมีผลกระทบเล็กน้อยต่อสมบัติทางกล เนื่องจากอุณหภูมิการรีดขั้นสุดท้ายมีความแตกต่างกันเล็กน้อย การวิเคราะห์โครงสร้างจุลภาคพบว่า อุณหภูมิการอบอ่อนที่สูงขึ้นส่งผลให้ขนาดเกรนเล็กลง ในขณะที่อุณหภูมิที่ต่ำกว่าจะทำให้เกิดการเรียงตัวของเกรนเฟร์ไรต์ที่ชัดเจน นอกจากนี้ ข้อบกพร่องบนพื้นผิวของเหล็ก เช่น รูปแบบรอยแตก ยังได้รับอิทธิพลจากทั้งอุณหภูมิการอบอ่อนและความเร็วการรีด การวิเคราะห์ด้วยกล้องจุลทรรศน์อิเล็กตรอนแบบส่องกราด ยืนยันความลึกและลักษณะของรอยแตกบนผิว ซึ่งสอดคล้องกับการสังเกตจากกล้องจุลทรรศน์แบบแสง โดยสรุป การปรับอุณหภูมิการอบอ่อนและความเร็วการรีดให้เหมาะสมมีความสำคัญอย่างยิ่งในการลดข้อบกพร่องบนพื้นผิวและเพิ่มคุณภาพของผลิตภัณฑ์ในกระบวนการรีดร้อนเหล็กกล้าเอชบีม

Isolation And Characterization Of Caffeine-Degrading Bacteria From Coffee Plantation Areas In Malaysia, Elvina Clarie Dullah, Mohd Fazli Farida Asras

Makara Journal of Technology

Decaffeination by microbial degradation is currently the most optimal and low-cost approach, involving only microbial cells and/or their enzymes. The bacterium was characterized using a series of biochemical tests. Positive results were obtained from carbohydrate fermentation, citrate utilization, and catalase tests, while negative results were obtained from Voges-Proskauer (VP) and indole tests. Three different caffeine concentrations of 0.25%, 0.4%, and 2% were tested and measured through Gas Chromatography-Mass Spectrophotometry (GC-MS) analysis. The highest caffeine reduction (89.25%) was found when 0.25% caffeine was used in the media. Only a small amount of caffeine was reduced to 0.4% and 2%, with 34.78% …

Optimization Of The Building Envelope And Roof Shading To Reduce The Energy Consumption Of College Low-Rise Buildings In Indonesia, Nasruddin Nasruddin, Azimil Gani Alam, Mohammad Imroz Sohel

Makara Journal of Technology

Energy consumption in buildings is a crucial concern globally, prompting researchers to explore innovative solutions to mitigate its impact. This study investigates the optimization of building envelopes and roof shading systems of existing buildings in Indonesia to realize notable energy savings. Multiple scenarios were explored, with modifications to building envelopes and roof shading, highlighting the overall thermal transfer value as a key parameter. Using EnergyPlus simulations, the efficacy of natural ventilation in corridors and roof shading modifications was assessed in reducing energy consumption. The findings revealed that renovating existing buildings by optimization of the building envelope and roof shading by …

Mechanical Characterization Of Functionally Graded M300 Maraging Steel Cellular Structures, Bradley Jay Sampson

Theses and Dissertations

Traditional methods for increasing the energy absorption of a structure involve using a stronger material or increasing the volume of the structure, resulting in a higher cost or additional weight. Additive manufacturing (AM) can be used to maximize the energy absorption of materials with the ability to create complex geometries such as cellular structures. Previous work has shown that the energy absorption of additively manufactured parts can be improved through functionally graded cellular structures; however, this strategy has not been applied to ultra-high strength steel materials. This work characterizes the effect of multiple functional-grading strategies (e.g. uniform, rod-graded, size-graded) on …

Cobalt Chromium In Biomedical Applications And The Development Of A Pspp Map, Nouralhouda Jamal

BCoE Publications

During the world wars, Cobalt-Chromium (Co-Cr) alloys gained prominence for their use in aircraft engine components, where they exhibited high temperature strength and durability. They are used in a wide range of industries due to their unique set of qualities, particularly strength, corrosion resistance, and biocompatibility. They have emerged as versatile materials with a broad spectrum of applications, from aerospace and automotive components to biomedical implants.

This paper presents a thorough analysis of its composition, processing techniques, microstructure, mechanical properties, and performance characteristics. The primary goal of this project is to develop a PSPP (Process, structure, properties, and performance) map …

Temperature Gradient Effect On Solid-Liqid Interface Properties Of Al-Cu Alloy: A Molecular Dynamics Study, Prashant Kumar Jha

All Theses

Aluminum-copper (Al-Cu) alloys are widely used in the aerospace industry due to their favorable strength-to-weight ratio, good fatigue resistance, and corrosion resistance. These properties make Al-Cu alloys an excellent choice for aircraft structural components that require high strength and low weight. Additive manufacturing (AM), also known as 3D printing, has emerged as a promising processing method for Al-Cu alloys in aerospace manufacturing. AM enables the production of lightweight optimized geometries difficult to manufacture through conventional subtractive methods. AM also reduces material waste by only depositing material where needed in the part geometry. The rapid solidification conditions in AM processes motivate …

The Shape Modulation Of Laser-Induced Nanowelded Microstructures Using Two Colors, Ariel Rogers, Isabelle Niyonshuti, Jun Ou, Diksha Shrestha, Deborah Okyere, Jingyi Chen, Yong Wang

Physics Faculty Publications and Presentations

The light-based nanowelding of metallic nanoparticles is of particular interest because it provides convenient and controlled means for the conversion of nanoparticles into microstructures and the fabrication of nanodevices. In this study, we investigated the wavelength dependence of laser-induced nanowelded shapes of silver nanoparticles (AgNPs). We observed that the nanowelded microstructures illuminated with only a 405 nm laser were more branched than those formed via illumination using both the 405 nm and 532 nm lasers. We quantified this observation by two compactness descriptors and examined the dependence of the power of the 532 nm laser. More importantly, to understand the …

An Investigation Into The Challenges Of Contemporary Additive Manufacturing: Insights Into The Metallurgical Response Of Materials And Relevant Solution, Huan Ding

LSU Doctoral Dissertations

Additive Manufacturing (AM) has gained attention in recent years due to its unique capabilities in the fabrication of complex parts. As with any new research, there is still a lack of sufficient understanding in the field of additive manufacturing, and further investigation is needed to solve existing problems. Ultimately, the aim is to enable the widespread use of AM components across various industries.

Chapter One provides a brief introduction to the background and current bottlenecks of additive manufacturing technology. Chapter two focuses on the development of high-strength 7075 aluminum alloy (Al7075) for Fused Deposition Modeling and Sintering (FDMS) technology. Al7075 …

Implementation Of Experimental Static Recrystallization Of High Strength Steel Into Computational Simulation Of Multi-Pass Slab Hot Rolling, S. K. Dasari, S. Ganguly, A. Abutunis, K. Chandrashekhara, M. F. Buchely, S. N. Lekakh, R. J. O'Malley, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural changes and softening due to static recrystallization have a critical influence on thermo-mechanical behavior of high strength steels during industrial multi-pass hot rolling. Numerical simulation using finite element analysis (FEA) can be used to accurately predict the softening behavior during the hot rolling process. Therefore, the implementation of an experimentally defined static recrystallization model into FEA is necessary to get realistic simulation prediction. in this study, the extent of softening during static recrystallization in Si and Mn alloyed high strength steel was measured using double hit tests. a Gleeble™ thermo-mechanical simulator was used to perform the double hit tests …