Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Engineering Science and Materials

Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 2701 - 2730 of 3187

Full-Text Articles in Materials Science and Engineering

Preparation And Properties Of The Composite Microporous Pvdf-Hfp/Sio2 Based Polymer Electrolytes, Bao-Wen Zhang, Lu Qi, Hui Hen, Xiao-Hui Zhu, Li-Yan Liu, Yun-Xiang Ci Nov 2003

Preparation And Properties Of The Composite Microporous Pvdf-Hfp/Sio2 Based Polymer Electrolytes, Bao-Wen Zhang, Lu Qi, Hui Hen, Xiao-Hui Zhu, Li-Yan Liu, Yun-Xiang Ci

Journal of Electrochemistry

Microporous PVDF-HFP/SiO2 film were prepared using a solvent/nonsolvent method-phase inversion method and the volatile plasticizers DMC, DEC or PC. The conductivity of the films increased pore volume measured by a nonsolvent uptake method. The conductivity of 1.86×10-3 S⋅m-1 were obtained using the liquid electrolyte LiPF6(1 M) in EC/DMC (1:1).

Go to article

Study On Degradation Of Phenol By Electrochemical Oxidation, Yue-Li Liu, Hong-Hua Ge Nov 2003

Study On Degradation Of Phenol By Electrochemical Oxidation, Yue-Li Liu, Hong-Hua Ge

Journal of Electrochemistry

Electrochemical oxidation of phenol was carried out by the Dimensionally Stable Anodes (DSA) electrode, which has been discarded as waste by alkali chloride factory. The result indicates that a good phenol removal can be obtained under certain phenol concentration by the DSA electrode. The key factor in effecting phenol removal of electrochemical oxidation is applied current density, the following factors are pH, electrolyte concentration and phenol concentration. After experiments, the optimal test conditions are 30 mA/cm2, pH 10, electrolyte concentration 10 mg/L, phenol concentration 10 mg/L.67% CODcr removal and 90% absorbance removal are gained by electrochemical oxidation for …

Go to article

Electrochemical And In-Situ Scanning Tunneling Microscopy Studies On The Sb Underpotential Deposition On Cu Single Crystal Electrodes, Ji-Hong Wu, Jia-Wei Yan, Jing Tang, Wen-Yun Hu, Bing-Wei Mao Nov 2003

Electrochemical And In-Situ Scanning Tunneling Microscopy Studies On The Sb Underpotential Deposition On Cu Single Crystal Electrodes, Ji-Hong Wu, Jia-Wei Yan, Jing Tang, Wen-Yun Hu, Bing-Wei Mao

Journal of Electrochemistry

We report electrochemical and in-situ STM studies on Sb UPD onto Cu(111) and Cu(100) electrode surfaces in HClO4 and H2SO4 solutions. The results indicate that the electrode surface structure as well as anion can considerably influence Sb UPD. Sb UPD on Cu(100) forms open adlayer structures, which is accompanied by surface alloying due to the more open structure of the (100) surface, On Cu(111), a more compact Sb adlayer is formed instead. Anion adsorption influences the dynamics as well as the adlayer structure of Sb UPD. Owing to the strong adsorption of SO42-, …

Go to article

Adsorption And Oxidation Of Phenol Electrode Processes, Bao-Cheng Wang, Yan-Ping Sun, Jin-Hua Zhu Nov 2003

Adsorption And Oxidation Of Phenol Electrode Processes, Bao-Cheng Wang, Yan-Ping Sun, Jin-Hua Zhu

Journal of Electrochemistry

The electrochemical behaviors of platinum electrode were studied by cyclic voltammetry in 1mol/L sulfuric acid solution and 1mol/L sulfuric acid solution contained phenol. The adsorption characteristics of phenol and the intermediat on electrode surface have been discussed. The reactive reversibility and oxidation mechanism of phenol on electrode process have been investigated.The potential of characteristic adsorption was suggested. The various products woud be formed when the electrode potential was greater than the one of characteristic adsorption.

Go to article

Preparation And Characterization Of Y-Type Carbon Nanotubes By Using Anodized Alumina Oxide (Aao) Template, Jing Zhang, Quan-Yong Gao, Yong Yang Nov 2003

Preparation And Characterization Of Y-Type Carbon Nanotubes By Using Anodized Alumina Oxide (Aao) Template, Jing Zhang, Quan-Yong Gao, Yong Yang

Journal of Electrochemistry

In this work, potential-modulation method was used in two-step anodization process to make an AAO template with Y-type nanochannels. Then Y-type carbon nanotubes with controlled length and branch angle were prepared in the template based on chemical vapor decomposion (CVD) method with Co particles as catalyst and C2H2 as carbon source. The Y-type nanotube branches exhibit the angle distribution ranging from 20° to 120°. The results demonstrated that the oxidation potential should be responsible for the angles and length of the branches. Short pulse and high oxidation potential will result in the short and dense nanotube branches.

Go to article

The Study Of Green Corrosion Inhibitors For Mild Steel 907 In Natural Seawater Environment, Ping Gong, Min Du, Qing-Zhang Wang, Zhen-Jun Mu Nov 2003

The Study Of Green Corrosion Inhibitors For Mild Steel 907 In Natural Seawater Environment, Ping Gong, Min Du, Qing-Zhang Wang, Zhen-Jun Mu

Journal of Electrochemistry

Nine green compounds, including calcium gluconate, zinc gluconate, zinc sulfate, garlic, ACUSOL 445N, OS-15, APG, OCTA and STPP were selected according to the methods of molecule design and function groups prune. The functions of combined corrosion inhibitors mixed by the compounds mentioned above for mild steel in seawater were studied in this work using the methods of polarization curve and weight-loss.The best weight ratio and distinct synergistic effect of calcium gluconate, zinc sulfate and OCTA were studied by Latin experiment. The afgereffects of the best weight ratio corrosoin inhibitor were studied by subsection experiment. In this way, a kind of …

Go to article

Optimizing Catalyst Layer Composition Of Pemfc By Orthogonal Method, Ming-Hua Wang, Xin-Jian Zhu, Guang-Yi Cao, Sheng Sui, Qing-Chun Yu, Ming-Ruo Hu, Zheng-Yu Fan Nov 2003

Optimizing Catalyst Layer Composition Of Pemfc By Orthogonal Method, Ming-Hua Wang, Xin-Jian Zhu, Guang-Yi Cao, Sheng Sui, Qing-Chun Yu, Ming-Ruo Hu, Zheng-Yu Fan

Journal of Electrochemistry

The optimal composition of catalyst layer in a PEMFC electrode was studied through orthogonal method. It was showed that the performance of hydrophilic electrodes, in which there is no PTFE in the catalyst layer, were more favorable than that of hydrophobic electrodes. According to this condition, the power density of PEMFC attained 0.37 w·cm-2 when the Nafion loading was 1.4 mg·cm-2, and the Pt loading was 0.4 mg·cm-2 in the catalyst layer, using H2 as fuel and air as oxidant both at atmospheric pressure. Additionally, the results showed that increasing Pt loading in Pt/C catalyst …

Go to article

The Study On Carbon Nanotube-Loaded Pt Catalysts For Proton Exchange Membrane Fuel Cells, Hong Zhu, Feng-Juan Ge, Xiao-Hong Kang, Yu-Guo Yang, Yun-Hua Xu Nov 2003

The Study On Carbon Nanotube-Loaded Pt Catalysts For Proton Exchange Membrane Fuel Cells, Hong Zhu, Feng-Juan Ge, Xiao-Hong Kang, Yu-Guo Yang, Yun-Hua Xu

Journal of Electrochemistry

Carbon nanotube-supported-platinum (Pt/CNTs) and carbon-supported-platinum (Pt/C) catalysts were synthesized by in-situ chemical reduction. They were analyzed using TEM and XRD, then made into electrodes to be part of assemable PEMFC for the performence tests. The resulted show that Pt clusters in both catalysts are of small particle size (about 4nm), and Pt/CNTs exhibits a higher catalytic activity than Pt/C.

Go to article

The Current Fluctuations Of Carbon Steel In Nano2-Nacl Solutions, Yu-Ming Tang, Yu Zuo Nov 2003

The Current Fluctuations Of Carbon Steel In Nano2-Nacl Solutions, Yu-Ming Tang, Yu Zuo

Journal of Electrochemistry

The characteristics of current fluctuations of A3 carbon steel in NaNO2-NaCl solutions were studied with potentiostatic and potentiodynamic polarization methods. The steel remained stable passivation in 0.1 mol/L NaNO2 solution without Cl-. After NaCl was added in to the solution, current fluctuations with a characteristic of quick increase and slow decrease occurred, indicating quick dissolution and slow re-passivation of the metastable pits. The metastable pitting may cause accumulated corrosion damage around certain area and result in observable pits. With the increase of chloride concentration, the occurring potential for metastable pits Em rised, and peak values …

Go to article

Comparison Of Thermal Cyclic Oxidation Of The Pvd Ni-Al And Hvof-Mcraly Coatings, J-T Chang, C-H Yeh, J-L He, K-C Chen Aug 2003

Comparison Of Thermal Cyclic Oxidation Of The Pvd Ni-Al And Hvof-Mcraly Coatings, J-T Chang, C-H Yeh, J-L He, K-C Chen

Journal of Electrochemistry

A PVD process-cathodic arc plasma ion plating was used to deposit Ni-Al films on Inconel 600 superalloy. The oxidation behaviors of PVD Ni-Al coating and the thermal sprayed CoCrAlY coatings were revealed and compared by performing cyclic thermal oxidation test at 1100 ℃ to evaluate its feasibility. Experimental results showed that the films with different compositions of Ni62Al38, Ni63Al37 and Ni69Al31 could be obtained when using Ni52Al48, Ni60Al40 and Ni70Al30 as targets, respectively. During the cyclic thermal oxidation test, the …

Go to article

Synthesis Of Polyunit Vapor Phase Inhibitor And Its Volatile Corrosion Inhibition Performance, Da-Quan Zhang, Li-Xin Gao, Guo-Ding Zhou Aug 2003

Synthesis Of Polyunit Vapor Phase Inhibitor And Its Volatile Corrosion Inhibition Performance, Da-Quan Zhang, Li-Xin Gao, Guo-Ding Zhou

Journal of Electrochemistry

A Mannich Base derivative (BMMCH), containing two morpholinum moieties and one cyclohexylamnonium moiety, was synthesized through aminomethy1 reaction. Its configuration was verified by IR and 1H-NMR. Its volatile rustproofing effect was appraised by volatile rustproofing sieve test and vapor inhabitability test. The result shows that BMMCH has good protection effect for carbon steel. BMMCH has lower volatility compared with dicyclohexylamnonium nitrite (DICHAN) via closed space volatile weight-loss test. The inhibition mechanism was studied by potentiodynamic polarization electrochemistry technique in ASTM simulated atmospheric water. The corrosion potential of carbon steel electrode shifted to a negative direction when BMMCH was joined …

Go to article

Effect Of Heat Laminating Aggregation Status Of Polymer Lithium-Ion Battery Cathode On Battery Performance, Ming-Gang Jin, Quan-Feng Dong, Ming-Sen Zheng, Li Huang, Hui-Qun Cai, Jin-Qua You, Zu-Geng Lin Aug 2003

Effect Of Heat Laminating Aggregation Status Of Polymer Lithium-Ion Battery Cathode On Battery Performance, Ming-Gang Jin, Quan-Feng Dong, Ming-Sen Zheng, Li Huang, Hui-Qun Cai, Jin-Qua You, Zu-Geng Lin

Journal of Electrochemistry

Multi-layer heat laminated polymer lithium ion battery was made, the effect of temperature of cathode laminating on battry performance was also investigated. It was discovered that suitable temperature of cathode laminating is critical to battery performance and is a key parameter to manufacture process control of polymer lithium ion battery.

Go to article

Influence Of Marine Organisms Upon Corrosion Of Steel Piling Systems, Jiunn-Shyong Luo, Cliff Rau, Kuei-Ching Chen Aug 2003

Influence Of Marine Organisms Upon Corrosion Of Steel Piling Systems, Jiunn-Shyong Luo, Cliff Rau, Kuei-Ching Chen

Journal of Electrochemistry

To study the influence of marine organisms upon corrosion of ASTM A36 steel piling sysems, specimens were immersed in both natural and synthetic seawater. Electrochemical techniques such as linear polarization resistance and electrochemical impedance scan(EIS) were applied to evaluate corrosion of the steel. The results indicated that attachment of marine organisms to form fouling layers on the steel surface reduced general corrosion, but localized corrosion occurred underneath marine organisms. An equivalent circuit model was established to simulate attachment of marine organisms upon carbon carbon steel surfaces.

Go to article

Discussion On Factors Of Unstable 304 Stainless Steel Stress Corrosion Cracking, Xin-Sheng Zhang, Chun-Chun Xu, Gang Hu Aug 2003

Discussion On Factors Of Unstable 304 Stainless Steel Stress Corrosion Cracking, Xin-Sheng Zhang, Chun-Chun Xu, Gang Hu

Journal of Electrochemistry

The 304 stainless steels were stretched at low temperatures to get different martensite phase transformation. Ferrmagnetometer was used to measure the martensite phase content. It was found that the dislocation density of 304 stainless sted was increased unavoidably with increase of deformation. Transmission electron microscope (TEM) was used to study the distribution of the dislocation. The influence of microstructure change on SCC of 304 stainless steel was discussed by slow strain rate testing (SSRT) in 42% MgCl2 boiling solution,metallurgical microscope and scanning electron microscope (SEM).The results showed that martensite phase and dislocation flaw act together on the SCC susceptibility …

Go to article

The Technique Of Rare-Earth Conversion Coatings On Aluminum Alloy, Jun-Tao Wang, Jian-Hua Wu, Guang-Zhang Chen Aug 2003

The Technique Of Rare-Earth Conversion Coatings On Aluminum Alloy, Jun-Tao Wang, Jian-Hua Wu, Guang-Zhang Chen

Journal of Electrochemistry

The orthogonal design was used to screen the film_forming technique on LY12 aluminum alloy using quadrivalent cerium salt, and the corrosion-resistance performance of the coating was studied. The results revealed that: after LY12 aluminum alloy was treated by cerium salt, its pitting potential shifts to positive direction while the corrosion potential slightly decreases, showing that the alloy becomes less sensitive to pitting corrosion was greatly improved, comparable to that after chromate treatment; in addition, by combining the results of electrochemical measurements with surface analysis, the mechanism of corrosion-resistance on the race-earth conversion coating of the aluminum alloy was also discussed.

Go to article

The Electroless Plating Ni-Fe-P Alloy And Its Voltammetric Behavior, Sen-Lin Wang, Hui-Huang Wu Aug 2003

The Electroless Plating Ni-Fe-P Alloy And Its Voltammetric Behavior, Sen-Lin Wang, Hui-Huang Wu

Journal of Electrochemistry

Electroless Ni-Fe-P alloy deposition from an alkaline bath, containing sodium hypophosphite as reducer, boric acid as buffer agent and sodium citrate as complexing agent, was investigated. To increase the plating rate and to inprove the bath stability, the deposition parameters were optimized. The effects of process parameters (pH, temperature and mole ratio of [Fe2+]/([Ni2+]+[Fe2+]) on the plating rate and deposit composition were examined and it was found that the presence of ferrous sulfate in the bath has an inhibitory effect on the alloy deposition. As a consequence, the percentage of iron in the electroless …

Go to article

Synthesis And Electrochemical Properties Of K2Feo4, Ning Zhou, Shi-Hai Ye, Yong-Long Wang, Xue-Ping Gao, Dong-Feng Lin, Zuo-Xiang Zhou, De-Ying Song Aug 2003

Synthesis And Electrochemical Properties Of K2Feo4, Ning Zhou, Shi-Hai Ye, Yong-Long Wang, Xue-Ping Gao, Dong-Feng Lin, Zuo-Xiang Zhou, De-Ying Song

Journal of Electrochemistry

The K2FeO4 used for new positive electrode materials was prepared. The primary batteries were used in different concentration of electrolyte and different currents. In 9 mol/L KOH , the capacity was the best. The higher the concentration of electrolyte, the lower the electric potential was. When the batteries discharged in 0.4 C , the capacity reached 521.3 mAh/g. By XRD, we gave the reasonable explanations for the discharge products of K2FeO4. Possible mechanism of discharge is discussed.

Go to article

Corrosion Fatigue And Dynamic Strain Aging Of Duplex Stainless Steel In Aqueous Solution, Chuan-Ming Tseng, I-Hsuang Lo, Wen-Ta Tsai Aug 2003

Corrosion Fatigue And Dynamic Strain Aging Of Duplex Stainless Steel In Aqueous Solution, Chuan-Ming Tseng, I-Hsuang Lo, Wen-Ta Tsai

Journal of Electrochemistry

The corrosion fatigue and dynamic strain aging behaviors of 22%Cr duplex stainless steel (DSS) in sodium chloride solutions were investigated. Austenitic 316L SS and ferrtic 430 SS were also used in this study for a comparison. The experimental results showed that no stress corrosion cracking (SCC) occurred in all these SSs tested in 3.5wt% NaCl solution at 80 ℃. However, dynamic strain aging (DSA) occurred in 316L austenitic SS and 22%Cr DSS during slow strain rate testing (SSRT) in this solution.The occurrence of DSA was dependent on solution temperature,strain rate and the presence of austenitic phase. The corrosion rate of …

Go to article

An Electrochemical Prediction Method For Caustic Scc Of Fe-Cr-Ni Alloy, Chun-Bo Huang, Zhan-Peng Lv, Wu Yang Aug 2003

An Electrochemical Prediction Method For Caustic Scc Of Fe-Cr-Ni Alloy, Chun-Bo Huang, Zhan-Peng Lv, Wu Yang

Journal of Electrochemistry

Stress corrosion cracking (SCC) of Fe-Cr-Ni alloy (alloy 800 M) in hot concentrated caustic solution was investigated by means of tests of C-rings under controlled potentials. The steady dissolution current densities (ist) of the plate specimens and C-rings polarized potentiostatically were measured. The simplifed steady potentiostatical curves were drawn on the basis of ist. The ratio RPD measured from ist and steady passive current density i p at low potentials (RPD = ist/ip) was designed as a polarization dissolution susceptibility parameter. The parameter RPD values of both plate …

Go to article

Electrochemistry And Electrocatalysis Of A Novel Μ-Oxamido Copper(Ⅱ) Binuclear Complex, Gui-Lian Gao, Guo-Bao Li, Qiu-Xia Yang, Xue-Lin Wang Aug 2003

Electrochemistry And Electrocatalysis Of A Novel Μ-Oxamido Copper(Ⅱ) Binuclear Complex, Gui-Lian Gao, Guo-Bao Li, Qiu-Xia Yang, Xue-Lin Wang

Journal of Electrochemistry

In this paper, the cyclic voltammetric and spectroelectrochemical behaviors of μ-oxamido Copper(Ⅱ) Binuclear Complex (deCu) in PBS were studied. Cyclic voltammograms of this complex in PBS (pH=9) exhibited two reductive peaks (Epc1 =-0.25 V, Epc2 = -0.50 V) at hanging mercury drop electrode(HMDE), peaks at -0.50 V and -0.25 V corresponded to the reduction of ligand and copper(Ⅱ) complex, respectively. The spectroelectrochimical experiments showed that there was a new absorption band at 440 nm, and the absorption peaks at 270 nm, 280 nm red shifted to 300 nm, 310 nm under potential of -0.75 V. It was meant …

Go to article

Severe Corrosivity And Its Eletrochemical Mechanism Of Seawater In Xiamen Sea Area To Al-Mg Alloys, Le-Yun Lin, Yue-Hong Zhao Aug 2003

Severe Corrosivity And Its Eletrochemical Mechanism Of Seawater In Xiamen Sea Area To Al-Mg Alloys, Le-Yun Lin, Yue-Hong Zhao

Journal of Electrochemistry

The surface layer seawater of different sea areas in China exhibit different corrosivity to Al-Mg alloys according to the experiment results of 16 years exposure in seawater. The seawater in Xiamen sea area possesses severe corrosivity while seawater in Qingdao possesses the mildest corrosivity to Al-Mg alloys with better regularity of corrosion behavior. The present paper illustrates by experiment data that the strongest corrosivity of Xiamen seawater to Al-Mg alloys is owing to the low salinity of the seawater and the “electrolyte effect” come from it. The 16 year corrosion data and corrosion morphology of the typical Al-Mg alloys from …

Go to article

The Mechanism Of Electrocatalytic Reduction Of Oxygen On Manganese Dioxide, Yu-Liang Cao, Han-Xi Yang, Xin-Ping Ai, Li-Fen Xiao Aug 2003

The Mechanism Of Electrocatalytic Reduction Of Oxygen On Manganese Dioxide, Yu-Liang Cao, Han-Xi Yang, Xin-Ping Ai, Li-Fen Xiao

Journal of Electrochemistry

The oxygen electroreduction on the MnO2 electrode was investigated by analysis of the polarzation properties of oxygen reduciton and its dependence on MnO2 discharge state, in combination with the characterization of discharge intermediate and the kinetic parameters of the oxygen reduction. Based on the experimental observation and mechanistic analysis, it was suggested that the reduction of oxygen was closely related to the discharge behaviors of MnO2. When MnO2 was electrochimically reduced to MnOOH, it was immediately oxidized by oxygen molecules. Thus the oxygen reduction proceeds through continuous oxidation of the discharge product of MnO2 …

Go to article

Initial Stages Of Pd Deposition Onto Au(111) Electrodes From Pdso4, Jing Tang, Petri M., Kibler L.A., Kolb D.M. May 2003

Initial Stages Of Pd Deposition Onto Au(111) Electrodes From Pdso4, Jing Tang, Petri M., Kibler L.A., Kolb D.M.

Journal of Electrochemistry

Metal thin films have attracted considerable interest in relation to catalysis, energy, material, corrosion and environmental protection. Pd thin film is capable of proton reduction and strong hydrogen absorption, which has shown electrocatalytic activity to the oxidation of small organic molecules. In this paper, in-situ STM measurements are performed to study the deposition process and the influence of the surface structure and anion adsorption. When Pd is deposited from PdSO4 solution on Au(111) in the UPD range, a monolayer of Pd with pseudomorphic (1×1) structure was formed on the substrate with induced (3×7) R19° SO42- adsorption. With …

Go to article

Preparation And Electrochemical Preformance Of Zn-La Alloys, Xian-Ling Meng, Hua-Bin Yang, En-Dong Yang, Xiao-Dan Wang, Hai-Chang Zhang, Jun-Hong Wang, Zuo-Xiang Zhou May 2003

Preparation And Electrochemical Preformance Of Zn-La Alloys, Xian-Ling Meng, Hua-Bin Yang, En-Dong Yang, Xiao-Dan Wang, Hai-Chang Zhang, Jun-Hong Wang, Zuo-Xiang Zhou

Journal of Electrochemistry

Zn-La alloys were prepared by solid phase diffusion method and the effects of La on the electrochemical performance of zinc electrodes were investigated using potentiostatic polarization technique and charging/discharging cycle test. The results showed that adding La to zinc electrode remarkably suppressed the zinc dendrite, the shape of zinc electrode and zinc corrosion, and hence, markedly improved the cycle performance of zinc electrodes. The discharging capacity of the zinc electrode containing 0.5at.% La which was the optimum was still 520 mAh/g after it cycled 80s at the current of 100 mA. The XPS showed that La element mainly adhered on …

Go to article

Study Of Marine Biocorrosion Using Afm And Molecular Techniques, Herbert H.P.Fang, Lichong Xu, Tong Zhang May 2003

Study Of Marine Biocorrosion Using Afm And Molecular Techniques, Herbert H.P.Fang, Lichong Xu, Tong Zhang

Journal of Electrochemistry

Biofilm is ubiquitous in nature.However,corrosin caused by biofilm is still by and large overlooked. This presentation is to demonstrate the applications of several newly developed analytical techniques in chemisrty and microbiology for the study of marine biocorrosion on steel. AFM(atomic force microscopy) was applied to investigate the initial formation mechanism of biofilm and the degree of corrosion of steel in polluted seawater. DNA/RNA-related molecular techniques were used to analyze the microbial composition corrosive biofilm. Results showed that microbial corrosion began within six days, and the corroded volume in the increased as a power function of time with an index 2.83. …

Go to article

Corrosion Behavior Of Reinforcing Steel In Concrete Subjected To Chloride Contamination By Eis, Rong-Gang Hu, Rong-Gui Du, Chang-Jian Lin May 2003

Corrosion Behavior Of Reinforcing Steel In Concrete Subjected To Chloride Contamination By Eis, Rong-Gang Hu, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

Electrochemical impedance spectroscopy(EIS) was employed to study the influence of chloride on the corrosion behavior of reinforcing steel in concrete. In Nyquist plot, the spectrum consists of two semicircles, indicating that the reinforced concrete system contained two time constants,one derived from electrical double layer of reinforcing steel and the other from the deposition film of concrete layer. The depressed semicircle in lower frequency featured the non-faradic behavior of the electrical double layer (EDL) deviated from idea capacitor due to diffusive effect which was attributed to the surface roughness of rebar and the inhomogenity of concrete layer. Then the EDL was …

Go to article

A Bilayer Self-Assembled Membrane Electrode For Fluorescence And Its Electrochemical Characterization, Xiang-Ying Sun, Bin Liu, Yun-Bao Jiang May 2003

A Bilayer Self-Assembled Membrane Electrode For Fluorescence And Its Electrochemical Characterization, Xiang-Ying Sun, Bin Liu, Yun-Bao Jiang

Journal of Electrochemistry

The bilayer membrane was assemblied on Au electrode by the electrostatic interaction between the fluorescence regent 1-naphthylamine diacetate acid (NADA) and DL-Cysteine. The SAMs electrode NADA/Cys/Au can be used as fluorescence and electrochemical sensor for metal ions. This paper states the electrochemical characterization of NADA/Cys/Au and SAMs' application in continous determination for Cu2+ and Ni2+.

Go to article

Synthesis And Electrochemical Characteristics Of Nickel-Based Complex Oxide LiANi0.78Co0.2Cd0.02O2, Rong-Zhong Yuan, Mei-Zhen Qu, Zuo-Long Yu May 2003

Synthesis And Electrochemical Characteristics Of Nickel-Based Complex Oxide LiANi0.78Co0.2Cd0.02O2, Rong-Zhong Yuan, Mei-Zhen Qu, Zuo-Long Yu

Journal of Electrochemistry

The nickel-based complex oxide LiaNi0.78Co0.02O2 cathode materials for lithium-ion rechargeable batteries was synthesized by the improved solid-state reaction method with LiOH·H2O, ball-like Cd-doped Ni(OH)2 and Co2O3 as raw materials. The analysis ICP-AES proved that the as-prepared compounds were near the stoichiometric form. The XRD, SEM and electrochemical characteristics testing were also carried out. The results showed that the complex cathode material LiaNi0.78Co0.2Cd0.02O2 has layered structure, homogeneous surface distributions,uniform particles with good crystal morphology as well as stable electrochemical …

Go to article

Perfluorinated Sulfonic Acid Lithium Conductivity Humidity Sensor, Hong-Feng Xu, Jing Liu, Li Wan May 2003

Perfluorinated Sulfonic Acid Lithium Conductivity Humidity Sensor, Hong-Feng Xu, Jing Liu, Li Wan

Journal of Electrochemistry

Treat carbon paper with 3% PTFE solution and dried in 340 ℃ for 40 minutes to enhance its intension, and level off the surface of the carbon paper with a mixture of XC-72 carbon black and PTFE solution. With those treated carbon paper as electrodes, recast Nafion thin film from 5% Nafion solution as humidity sensitive material, a solid polymer electrolyte humidity sensor was prepared on a thin PET film. Take the relative humidity data from several saturated salt solutions, the relationship between conductivity response and relative humidity was studied at different relative humidies .The results showed: when the polymer …

Go to article

The Electrochemical Behaviors Of A Novel Ferrocene Alkylthiol Sams On Au Electrode, Xiao-Gang Zhang, Yan-Li Shi, Hu-Lin Li May 2003

The Electrochemical Behaviors Of A Novel Ferrocene Alkylthiol Sams On Au Electrode, Xiao-Gang Zhang, Yan-Li Shi, Hu-Lin Li

Journal of Electrochemistry

A novel alkylthiol molecule containing ferrocene and pyridium moieties and its hydrogenated products were synthesized and subsequently assembled on Au electrode as SAMs. Cyclic voltammogram(CV) was used to investigate the structure-dependent electrochemical response of the SAMs in 0.1 mol/L HClO4 aqueous solution.

Go to article

First Prev Next Last