Materials Science and Engineering Commons^™

Influence Of Connection Placement To The Behavior Of Precast Concrete Exterior Beam-Column Joint, Elly Tjahjono, Heru Purnomo

Makara Journal of Technology

Influence of Connection Placement to the Behavior of Precast Concrete Exterior Beam-Column Joint. This paper presents an experimental study on the influence of connection placement to the behaviour of exterior beamcolumn joint of precast concrete structure under semi cyclic loading. Four half-scale beam-column specimens were investigated. Three beam-columns were jointed through connection that are placed in beam-column joint region and the forth is connected at the plastic hinge potensial region of the beam. Crack patterns, strength, stiffness and ductility of the test specimens have been evaluated. The test result indicated that all beam-column specimens show good ductility behavior.

Modelling And Simulation Of Packed Bed Catalytic Converter For Oxidation Of Soot In Diesel Powered Vehicles Flue Gas, Mohammad Nasikin, Praswasti P.D.K. Wulan, Vita Andrianty

Makara Journal of Technology

Modelling and Simulation of Packed Bed Catalytic Converter for Oxidation of Soot in Diesel Powered Vehicles Flue Gas. Diesel vehicle is used in Indonesia in very big number. This vehicle exhausts pollutants especially diesel soot that can be reduces by using a catalytic converter to convert the soot to CO2. To obtain the optimal dimension of catalytic converter it is needed a model that can represent the profile of soot weight, temperature and pressure along the catalytic converter. In this study, a model is developed for packed bed catalytic converter in an adiabatic condition based on a kinetic study that …

Optic Properties On Aggase2 Polycristal Fabrication, A. Harsono Soepardjo, I Dewa Made Janusetiawan

Makara Journal of Technology

Optic Properties on AgGaSe2 Polycristal Fabrication. Polycristal AgGaSe2, is compound (I-III-VI2) a semiconductor as basic material for thin film for solar cell. Polycristal was succesfully grown using Bridgmann Method, heated on sequential temperature treatment until 850°C and cooled down slowly until room temperature. Results observed were in the form of ingot (bars) with more or less 3 cm length and 13 mm in diameter. By using X-Ray Fefraction, composition obtained of each element (weight %) was Ag = 29,3996 %, Ga = 36,8123 % and Se = 30,29 % while using X-Ray Difraction lattice parameter obtained/calculated a = 4,4112 Å, …

Electrochemical Behaviours Of Hemoglobin-Ddab-Modified Powder Microelectrode And The Application Of The Powder Microelectrode In Determination Of Nitric Oxide, Zhi-Mou Guo, Huan Liu, Jian Chen, Wen-Ting Zhang

Journal of Electrochemistry

The electrochemical behaviours of DDAB-Hb-PME were studied in this paper. The (apparent) surface concentration of Hb was enhanced greatly by using the powder microelectrode (technique). NO reacts with Hb and absorbs on the surface of the modified carbon powder. Therefore, the output of the electrode was enhanced greatly by employing PME with higher reaction surface (area). The sensitivity of DDAB-Hb-PME is 3.1 mA/μmol·L^-1·cm², which is much larger than the values obtained with the traditional electrodes. The detection limit is 9 nmol·L^-1 and the linear response range is 9～100 nmol·L^-1.

Improvement And Its Mechanism Of Storage Performance Of Ni-Mh Battery, Xiao-Feng Li, Li-Ping Ma, Yu-Wan Lou, Feng Li, Bao-Jia Xia

Journal of Electrochemistry

The storage performance of nickel-metal-hydride (Ni-MH) battery was studied by using galvanostatic charge-discharge and cyclic voltammetry. The experimental results indicated that CoOOH could not be completely restored after its being thoroughly reduced at lower potential, which might weaken electric conduction network in the positive electrode and result in fading of electrochemical properties of Ni-MH battery. Addition of nickel powder as a conductive agent into the positive electrode was beneficial to the capacity recovery after storage.

Effect Of Fe3+ Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang

Journal of Electrochemistry

Photo-catalytic titanium dioxide film in nano crystalline has been prepared by electrochemical oxidation process and adding different amount of ferric ion into the electrolyte during the anodic oxidation.The effects of Fe³⁺ dopen on absorption spectra and photo-catalytic of the titanium dioxide films have been studied. It shows that the Fe³⁺ dopen caused the red shife of the absorption edge for the incoming light and exhibited the improved photocatalytic reactivity.

LicoXNi1-XO2 Cathode Materials Prepared By Electrolysis Of Co And Ni, Jin-Ping Wei, Xin Sun, Xiao-Yu Wang, Xi-Kui Bian, Jin-Ling Zhai, Yan-Jie Yan-Jie

Journal of Electrochemistry

A new electrolytic method was developed to prepare LiCo_xNi_1-xO₂ as a cathode material of lithium-ion battery. Contrary to the traditional method, electrolytic method is a potential method with simple process to industrialization and no pollution. Metal cobalt and nickel were electrolysed in parallel to prepare the precursor of Co_xNi_{1- x}(OH)₂.Different compositional precursors could be conveniently prepared by changing electrolytic current. The LiCo_0.3Ni_0.7O₂ cathode prepared by this method was found favorable charge-discharge and cycle properties. For the LiCo_0.3Ni_0.7O₂ cathode material, …

Preparation And Photo-Catalyst Properties Of The α-Fe2O3-Tio2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen

Journal of Electrochemistry

Three new nano thin films of α-Fe₂O_3, TiO₂ and α-Fe₂O₃-TiO₂ by doping their powder with sodium alginate polymer were prepared. Surface structure and catalytic activities of the films were characterized by FTIR, XRD, PL, TEM and I-V techniques. The results of UV-visible absorption showed that the methylene blue was mineralized in aqueous of α-Fe₂O₃/SA, TiO₂/SA and (α-(Fe₂O₃))-TiO₂ /SA upon radiation with ultra violet light. α-Fe₂O₃ enhanced their photo-decolorized-activities by doping 15% TiO₂.

Applications Of New Activated Carbon Meterials In The Electric Double-Layer Capacitor, Jian-Jun Zhang, Hua Jiang, Jian-Hui Fang, Li-Yi Shi, Ren-He Yin, Yi Wen, Ji-Quan Liu

Journal of Electrochemistry

A new type activated carbon whose precursor was coconut shell could be obtained using specific physics-chemistry activation, and the activated carbon was applied as the material of electrode in EDLC (electrical double-layer capacitor),which had a large specific capacitance, and could charge and discharged in some large currents. Carbon dioxide and acid were used to modify carbon,and the effects of post-treatment on surface area and pore volume were investigated. A moulding method which has influence on some properties of carbon electrode with PTFE additive was researched in the paper.

Electrocatalytic Performances Of Carbon Nanotube Air Electrode For Oxygen Reduction, Feng-Ming Zhao, Chun-An Ma

Journal of Electrochemistry

The air electrodes with different mass ratio of Pt/active carbon or carbon nanotube as catalyst layer material have been prepared. The electrocatalytic performances for oxygen reduction were evaluated by means of polarization curve and electrochemical impedance spectroscopy (EIS). The results disclosed that carbon nanotubes dealt with nitric acid in the catalyst layer had been improved obviously on the electrocatalytic activity. After the surface of carbon nanotube was oxygenated and aggraded with platinum, the catalyst had obviously effects on the electrocatalytic activity. The air electrode with the mass ratio of active carbon to Pt/carbon nanotube in 4∶1 showed better electrocatalytic activity, …

The Investigation Of Bafesi/C Alloy Composite As Anode Materials For Li-Ion Battery, Rui-Xiang Feng, Hua Dong, Xin-Ping Ai, Han-Xi Yang

Journal of Electrochemistry

A novel BaFeSi/C composite was prepared by mechanical ball milling, and lithium insertion reactions on the composite electrode were investigated by cyclic voltammetry , charge-discharge measurements, XRD and XPS spectroscopy. It is demonstrated that the capacity retention with indiscernible capacity decas during charge-discharge cycling. The improved cycling ability of the composite is suggested from a cooperative action by inactive FeSi₂ and BaSi₂ matrix and outer graphite shell, which both buffer the volumetric changes of the active Si phase and provide a good connection for electronic and ionic conduction during lithium insertion and extraction processes.

Modeling, Fabrication, And Optimization Of Niobium Cavities Phase Iii: Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

This quarterly report provides an update to the last phase of the Modeling, Fabrication, and Optimization of Niobium Cavities. Designing the experimental setup of secondary electron emission was well underway in early summer of 2003 when funding was made available for this portion the study. By March 2004, many of the components of the experimental study reached UNLV with some assembly accomplished. The first secondary electron emission (SEE) measurement was made from the surface of a Faraday cup in September 2004. At a particular beam energy, the current measured with the Faraday cup and electrometer changed sign over a range …

Electrochemical Reduction Of Nitrobenzene On The Wc Electrode In Acidic Solution, Chun-An Ma, You-Qun Chu, Ying-Hong Zhu, Zhi-Hua Xu

Journal of Electrochemistry

The tungsten carbide (WC) electrode was constructed by using polyterafluoroethylene as binder. The electrochemical behavior of nitrobenzene on the WC electrode in acidic solution was investigated by cyclic voltammetry, linear scan method and chronoamperometry. Experimental results showed that WC electrode had good activity for the electrochemical reduction of nitrobenzene, and the electrode process was controlled by diffusion and electrochemical stepssimultaneously. The apparent active energy of the electrode process is 23.7kJ⋅mol^-1, while the active energy of the electrochemicalstep is 10.91kJ⋅mol^-1.

Preparation And Electrochemical Performance Of New Composite Seperators For Lithium-Ion Batteries, Hu Cheng, Hong-Yan Du, Yong Yang

Journal of Electrochemistry

New composite seperators for lithium ion batteries were prepared by coating PEO mixed with nanosize SiO₂ onto microporous polypropylene(PP) seperators. Highly conductive electrolytes were prepared by soaking them in an electrolyte solution. With these composite separators, the lithium ion cell consisting of Li anode and LiNi_0.8Co_0.2O₂ cathode were assembled. The high initial discharge capacity and good capacity retention were obtained through the cell.

Solid State Synthesis And Electrocatalysis Of Pt/Moo3 For The Oxidation Of Methanol, Qing Wang, Yi-Ming Zhou, Yang Shao, Yi-Gang Ji, Juan Xu, Ya-Wen Tang, Tian-Hong Lu, Tao Shen

Journal of Electrochemistry

The electrocatalyst, Pt/MoO₃ synthesized by solid state reaction, was used for the oxidation of methanol in direct methanol fuel cells. The X-Ray diffraction and cyclic voltammetry were employed to investigate the performance of the material. It was shown that the typical diffraction peaks for Pt appeared in XRD. And a good electrocatalysis for methanol oxidation was observed. The peak potential of the methanol oxidation appeared at ca. 0.63V(vs.SCE) and the peak current density for the oxidation was 78.1 mA⋅cm^-2.

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin

Journal of Electrochemistry

TiO₂(B) Nanobelts were synthesized by using the "Soft chemical"method. The products were characterized by means of transmission electron microscope(TEM), X-ray diffraction(XRD), Raman spectrum and energy dispersive spectrum(EDS). Galvanostatic charging and discharging tests showed that lithium-ion intercalation/deintercalation occurred reversibly in the TiO₂(B) nanobelts electrode, and a high capacity (265 mAh·g^-1) can be obtained. The results suggested that TiO₂(B) Nanobelts might be a promising negative electrode material of second Lithium battery.

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren, Zhen-Xing Liang, Xin-Sheng Zhao, Qin Xing, Gong-Quan Sun, Xue-Feng Yang

Journal of Electrochemistry

This paper describes the methanol permeability characterization of SPEEK membranes and their feasibility for DMFC application. The SPEEK membranes showed a significant lower methanol permeation than Nafion 115 determined from voltammetric methods. An increase in open circuit voltage was found in the performance of SPEEK membranes in DMFC. The power density of the cell using SPEEK membrane was considerably poorer than that of Nafion 115. If modified properly, the SPEEK membranes can be chosen for DMFC application based on this study.

Study On An Intermediate Temperature Planar Solid Oxide Fuel Cell, Shao-Rong Wang, Wen-Xia Chen, Ting-Lian Wen, Jia-Di Cao, Zhi-Yi Lv, Da-Qian Wang

Journal of Electrochemistry

Tape cast method was applied to prepare green sheets of Ni/YSZ anode supported YSZ thin film. After isostatic pressure treatment and cosintering, the YSZ film on the Ni/YSZ anode was gas-tight dense, and 15~30 μm thick. The area of the composite film was over 100 cm². A Ce_0.8Sm_0.2O_1.9 (CSO) interlayer was sintered on to the YSZ electrolyte film to protect La_0.6Sr_0.4CoO₃ (LSCO) cathode from reaction with YSZ at high temperatures. The LSCO cathode layer was screen printed onto the CSO interlayer and sintered at 1200 ℃ for 3 …

Fabrication Of Solid Oxide Fuel Cells And Analysis Of Their Structure And Performance, Nai-Tao Yang, Bo Meng, Ru-Jun Yu, Xiao-Yao Tan

Journal of Electrochemistry

An intermediate temperature solid oxide fuel cell (IT-SOFC) was fabricated by co-copressing-sintering methods, and the electrolyte of Ce_0.8Gd_0.2O_1.9 (CGO) and cathode materials of La_0.6Sr_0.4Co_0.2Fe_0.8O_3-α (LSCF) were prepared by sol-gel method. The effect of preparation methods on the microstructure of the prepared fuel cells was analyzed by SEM . It shows that the cells prepared by the co-pressing/co-sintering method possess a dense electrolyte layer and a compact interface between electrolyte and anode but a curved configuration, while those prepared by the colloidal technique have a flat configuration …

Synthesis Of (S)-3-Phenylpropane-2-Tert-Butoxycarbonylamino-1-Thiol And Its Electrochemical Behavior Self-Assembled On Gold, Ru Sun, Jian-Feng Ge, Mei Wang, Ren-Ao Gu

Journal of Electrochemistry

The synthesis of (S)-3-Phenylpropane-2-tert-butoxycarbonylamino-1-thiol(N-Boc-APT) from L-phenylalanine was reported. L-Phenylalanine was reduced to the corresponding amino alcohol, protection of the amino group using tert-butyl pyrocarbonate gave (S)-2-tert-butoxycarbonylamino-3-phenylpropane-1-ol, which was then O-mesylated and treated with potassium thioacetate in DMF to give 3-phenylpropane-2-tert- butoxycarbonylamino-1-etylmercapto. After the acetyl group was removed with ammonia in alcohol, the desired target molecular was obtained. The structure of intermediate and target molecular was conformed by IR and ¹HNMR. We made N-Boc-APT self-assemble-modificated gold electrode and investigated its electrochemical behavior. The CV results of methylene blue on nano-Au/N-Boc-APT SAM/Au electrode showed that nano-Au could speed this electron transfer …

Synthesis And Electrochemical Behavior Of Layered-Structure Limn1-XCrXO2, Jie Xiao, Hui Zhan, Yun-Hong Zhou

Journal of Electrochemistry

The Layered-structure LiMn_1-xCr_xO₂(x=0, 0.15) solid solution has been prepared by the rheological phase method. From the XRD results, undoped LiMnO₂ crystallized almost entirely in the orthorhombic phase while the structure of LiMn_0.85Cr_0.15O₂ belongs to monoclinic phase. TEM investigation shows that the final powder product consists of ultrafine spherical particles which are distributed homogeneously, with the average diameter ranging from 60 to 300nm. The initial discharge capacity of LiMn_0.85Cr_0.15O is much higher than that of undoped LiMnO₂. After 40 cycles, the capacity retention …

Wavelenght-Dispersive X-Ray Flourescence Accuration, H. Widyatmoko

Makara Journal of Technology

Wavelenght–Dispersive X-Ray Flourescence Accuration. X-Fuorescence spectrometry is a method, which is increasingly applied in the geochemical analysis. X-Fuorescence spectrometry is classified under two categories – WDXRF (wavelenght – dispersive X-ray fluorescence spectrometer) and EDXRF (energy-dispersive X – ray fluorescence spectrometer). WDXRF can be configured as a sequential spectrometer , a simultaneous spectrometer or a hibrid instrument, which combines the advantages of the simultaneous and sequential spectrometers into one instrument. Each instrument is different in some characteristics, and each has applications for which it is specifically suited. In this investigation sequential spectrometer PW 1450 was used to analyze the major, minor …

Secondary Flow Experimental Study For Axial Compressor Cascade Strong Stagger With And Without Tip- Clearance: Static Pressure Distribution On Blade Surface, Syamsuri Syamsuri

Makara Journal of Technology

Secondary Flow Experimental Study for Axial Compressor Cascade Strong Stagger With and Without Tip- Clearance: Static Pressure Distribution on Blade Surface. The performance of blade cascade is influenced by the growth and boundary layer’s separation along blade surface and endwall (casing and hub). The secondary flow which happens near hub and casing compressors is three dimentional flow separation phenomenon comes from interaction blade boundary layer with casing and hub boundary layers in the compressor. The secondary flow causes secondary losses, blockage effect, and turning angle (deflection) distribution along blade span. The result of the research shows that the increase of …

Effect Of Photoperiodicity On Co2 Fixation By Chlorella Vulgaris Buitenzorg In Bubble Column Photobioreactor For Food Supplement Production, Anondho Wijanarko, Dianursanti Dianursanti, Arief Budi Witarto, Roekmijati Widaningroem Soemantojo

Makara Journal of Technology

To reduce the level of CO2 content in air, effort on converting CO2 to useful products is required. One of the alternatives includes CO2 fixation to produce biomass using Chlorella vulgaris Buitenzorg. Chlorella vulgaris Buitenzorg is applied for production of food supplement. Chlorella vulgaris Buitenzorg is also easy to handle due to its superior adaptation. Currently, Chlorella vulgaris Buitenzorg has been analyzed by some experts for its cellular composition, its ability to produce high quality biomass and the content of essential nutrition. A series of experiments was conducted by culturing Chlorella vulgaris Buitenzorg using Beneck medium in bubbling column photobioreactor. …

Synthesize Of Emulsion Polymer Latex For Sub-Grade Cbr Improvement In The Road Construction, Keba Moto, V. Julian, Syamsudin Syamsudin, T. A. Wiradi, S. R. Wijaya

Makara Journal of Technology

Synthesize of emulsion polymer latex for sub-grade CBR improvement in the road construction. Latex polymer for California Bearing Ratio (CBR) enhancement in sub-grade soil of road building has been prepared by emulsion polymerizations technique. The prepared polymer then characterize by Fourier Transform Infrared (FTIR). For application purpose, CBR test was done to the compacted polymer added-soil. The CBR test is done also for both soaked and unsoaked samples. It is found that our latex polymer is better then other imported latex polymer. For the latex polymer, which is design to have Temperatur glass (Tg) around 9.8-19.6o, indicating the formation of …

Fabrication, Characterization, And Modeling Of Organic Capacitors, Schottky Diodes, And Field Effect Transistors, Mo Zhu

Doctoral Dissertations

The objectives of this project are to fabricate, characterize, and model organic microelectronic devices by traditional lithography techniques and Technology Computer Aided Design (TCAD).

Organic microelectronics is becoming a promising field due to its number of advantages in low-cost fabrication for large area substrates. There have been growing studies in organic electronics and optoelectronics. In this project, several organic microelectronic devices are studied with the aid of experimentation and numerical modeling.

Organic metal-insulator-metal (MIM) and metal-insulator-semiconductor (MIS) capacitors consisting of insulating polymer poly(4-vinylphenol) (PVP) have been fabricated by spin-coating, photo lithography, and reactive ion etching techniques. Based on the fabricated …

Synchronous Motor Phase Control By Vector Addition Of Induced Winding Voltages, Daniel J. Simon, Dennis L. Feucht

Electrical and Computer Engineering Faculty Publications

We propose a simple low-cost approach to the winding-sensed control of three-phase synchronous permanent-magnet motors. Our approach results from a straightforward but elegant application of vector-based motor theory. The method therefore does not depend on the differential equations that describe the motor dynamics, and it does not depend on the particular motor parameters. The single method we derive applies to both wye- and delta-configured motors. We vectorially sum the voltage waveforms at the motor terminals in a certain way and use their zero crossings to produce a correctly phased six-step switch sequence. We discuss the implementation for both wye- and …

Direct Electron Transfer Of Redox Proteins And Enzymes Promoted By Carbon Nanotube, Chen-Xin Cai, Jing Chen

Journal of Electrochemistry

The redox proteins (enzymes), such as hemoglobin (Hb), horseradish peroxidase (HRP) and glucose oxidase (GOx) were immobilized on the surface of the carbon nanotube modified with glassy carbon (CNT/GC) electrode, respectively. The experimental results showed that the redox proteins (enzymes) underwent effective and stable direct electron transfer reaction at the surface of CNT/GC electrode with a pair of nearly symmetrical redox peaks in phosphate buffer solution. The formal redox potential, E^0' , is almost independent on the scan rates, the average value of E^0'  for Hb, HRP and GOx is -0.343±0.001, -0.319±0.002 and -0.456±0.001 V (vs.SCE,pH 6.9), respectively. …

Electrocatalytic And Lifetime Studies Of Commercial Catalystsin A Pemfc, Cheng Xuan, Yan-Yun Ma, Li Qi, Cheng Peng, Ling Chen, Jun Zhao, Ying Zhang, Qin-Bai Fan

Journal of Electrochemistry

A particularly designed H-type cell was used to simulate the operating condition of a hydrogen-air proton exchange membrane fuel cell (PEMFC). The electrocatalytic activity, morphology, structure and lifetime of commercially available catalysts, carbon support platinum (Pt/C) and unsupported platinum-ruthenium (Pt-Ru), were preliminary studied by carrying out electrochemical measurements and by SEM, XRD techniques. The catalysts were simultaneously tested in the H-cell under operation, and also separately tested in a conventional electrochemical cell for comparison. It was found that the characteristic peaks of hydrogen adsorption/desorption on cyclic voltammograms shifted considerably to a more positive direction for Pt/C, while a more negative …

Electrochemical Lithium Insertion Of Nanosized Tio2, Ying Lan, Jian-Wen Liu, Xue-Ping Gao, Xing-Di Zhou, Jin-Qiu Qu, Feng Wu, De-Ying Song

Journal of Electrochemistry

The protonic titanate nanotubes with the diameter of 10～15 nm were synthesized via hydrothermal method in NaOH solution and the calcined nanotubes at 500 ℃ were transferred to anatase nanorods with the diameter of 12～20 nm due to dehydration.The electrochemical behavior of the anatase nanorods as lithium insertion materials was examined. The results showed that the nanorod electrode had the high initial discharge capacity of 232 mAh/g and second reversible capacity of 198 mAh/g. The capacity of nanorod electrode maintained 152mAh/g after 20 cycles.