Materials Science and Engineering Commons^™

The Electrocatalystic Investigation Of 3,4-Dihydroxybenzoic Acid On The Modified Multiply Wall Carbon Nanotubes, Ming-Qi Li, Duo-Chang Cai, Xiao-Ying He

Journal of Electrochemistry

The electrochemical behavior of 3,4-Dihydroxybenzoic acid(DHBA) on modified multiply wall carbon nanotubes electrode was investigated by cyclic voltammetry(CV) and square wave voltammetry(SWV). Results show that in 0.1 mol/L HCl solutions the modified carbon nanotube electrode has an obvious electrocatalytic effect on the oxidation and deoxidization of DHBA. The oxidation current of DHBA is linear to it's concentration in the range of 4.0×10^-6～1.0×10^-4 mol/L and 2.0×10^-4～8.0×10^-4 1mol/L with correlation coefficient of 0.9995 and 0.9992. The detection limit is 1.0×10^-6 mol/L.

Simultaneous Treatment Of Organic (Phenol) And Heavy Metal (Cr6+ Or Pt4+) Wastes Over Tio2, Zno-Tio2 And Cds-Tio2 Photocatalysts, Slamet Slamet, R. Arbianti, Daryanto Daryanto

Makara Journal of Technology

Simultaneous Treatment of Organic (Phenol) and Heavy Metal (Cr6+ or Pt4+) Wastes over TiO2, ZnO-TiO2 and CdS-TiO2 Photocatalysts. Treatment of heavy metal (Cr6+ and Pt4+) and organic (phenol) wastes has been studied using the relatively new method, i.e. simultaneous photocatalytic process over TiO2 photocatalysts in the batch photoreactor. Following the photocatalytic reduction of the heavy metal wastes, recovery of Cr and Pt was carried out by precipitation and leaching method, respectively. The experimental results show that in the simultaneous photocatalytic system, there is a synergism effect between the photocatalytic reduction of heavy metal waste (Cr6+ or Pt4+) and the oxidation …

Development Of Low Frequency Vibration Method Of Direct-Write Deposition Relevant To Layer Manufacturing Application, Susilo Adi Widyanto, Alva Edy Tontowi, Jamasri Jamasri, Heru Santosa Budi Rochardjo

Makara Journal of Technology

The research of deposition process is the first step in development process of multi materials selective laser sintering. The deposition process enables to settle multi materials powder in horizontal formation on one layer. In this research we use low frequency (70 - 200Hz) to vibrate a hopper nozzle in which powder is settled. The research method consists of two steps, the first step is to determine flow-ability parameters and the second is to join flow ability parameter with other parameters such that the line width can be controlled. The results show that the line width depends on uniformity of particle …

Design Of Product Placement Layout In Retail Shop Using Market Basket Analysis, Isti Surjandari, Annury Citra Seruni

Makara Journal of Technology

Retailing is an industry with high level of competition. It is a customer-based industry which depends on how it could be aware of what the customers’ needs and requirements are. One technique most used in supermarkets is the mix merchandise. The purpose of this paper is to identify associated products, which then grouped in mix merchandise with the use of market basket analysis. This association between products then will be applied in the design layout of the product in the supermarket. The process of identifying the related products bought together in one transaction is done by using data mining technique. …

Production Hydrogen And Nanocarbon Via Methane Decomposition Using Ni-Based Catalysts. Effect Of Acidity And Catalyst Diameter, Widodo W. Purwanto, M. Nasikin, E. Saputra, L. Song

Makara Journal of Technology

Objectives of this research are mainly to study impacts of acidity strength (by varying amount of precipitant and loading Al-Si) and the effect of nickel particle size (by varying calcinations temperature) on decomposition reaction performances. In this research, high-nickel-loaded catalyst is prepared with two methods. Ni-Cu/Al catalysts were prepared with co-precipitation method. While the Ni-Cu/Al-Si catalyst were prepared by combined co-precipitation and sol-gel method. The direct cracking of methane was performed in 8mm quartz fixed bed reactor at atmospheric pressure and 500-700°C. The main results showed that the Al content of catalyst increases with the increasing amount of precipitant. The …

Design And Implementation Of 1-2 Ghz Stepped Frequency Gpr For Buried Metal Detection, Joko Suryana, Andriyan B. Suksmono, Tati R. Mengko

Makara Journal of Technology

Design and Implementation of 1-2 GHz Stepped Frequency GPR for Buried Metal Detection. In this paper, we describe the design and realization steps of 1 – 2 GHz SFGPR (Stepped Frequency Ground Penetrating Radar) transceiver for metal detection under the ground. Before using prototyped GPR for detecting the metal under the ground, several of calibration processes must be performed, namely phase calibration and monocycle pulse waveform calibration. After completing the calibrations, this prototyped GPR would be ready for detecting a hidden object such as a metal plate 5 cm under the ground in our small test range size 25 cm …

Synthesis Of Fuel Cell Membrane: Copolymerization Of Styrene On Etfe Film By Grafted Pre-Irradiation, Yohan Yohan, Rifai M. Nur, Lilik Hendrajaya, E. S. Siradj

Makara Journal of Technology

Synthesis of Fuel Cell Membrane: Copolymerization of Styrene on ETFE Film by Grafted pre-Irradiation. Preirradiation Grafting styrene monomer on ETFE film has been prepared. Research has been performed by γ-ray radiation at various total dose from 2.5 – 12.5 kGy and various dose rate from 1.3 – 1.9 kGy/hour. Irradiated copolymer is then grafted by styrene monomer in various solvent: ethanol, 2-propanol, and toluene, various concentration from 20 – 70% volume, various temperature from 50 – 90oC, and various grafting time from 2 – 12 hours. The results showed that percent of grafting is increase with increase of total dose …

Design Of Generating Dual Frequency Operation For Triangular Microstrip Antenna Using Electromagnetic Coupling, Indra Surjati, Eko Tjipto Rahardjo, Djoko Hartanto

Makara Journal of Technology

Design of Generating Dual Frequency Operation for Triangular Microstrip Antenna Using Electromagnetic Coupling. A new design is proposed in this paper by applying a pair of slits using a microstrip feed line. Therefore the microstrip line feeding system is electromagnetically coupled to the patch. The antenna works at two different frequencies in the range from 2 GHz to 4 GHz (S band frequency). The results of the simulation shows that the dual frequency operation can be created when the slit width is 1 mm and the height of the slits ranges from 10 mm to 14 mm with inter slit …

Ozone Concentration In An Atmospheric Pressure Air Plasma Jet, Srinivas Reddy Suddala

Electrical & Computer Engineering Theses & Dissertations

A stable micro-plasma jet in air was generated from a direct current discharge between two molybdenum electrodes (0.25 mm thick) that were separated by an alumina insulator of the same thickness. The after-glow plasma jet was generated by blowing air through the space between the electrodes. A change from laminar to turbulent flow was observed at a gas flow rate of 140 ml/min. The length of the plasma jet increased with flow rate in the laminar mode to approximately 15 mm and decreased in the turbulent mode.

Increasing the gas flow rate up to 200 ml/min at a constant discharge …

Electrocatalytic Oxidation And Degration Of Active Red X-3b By Nanotubes Catalytic Electrodes, Yi Wen, Jian-Hui Fang, Wei-Min Cao, Li-Yi Shi

Journal of Electrochemistry

The catalytic splitting decomposition of carbon nanotubes isprocessed by dispersing with dilute nitric acid and thermal oxidation. Then well-proportionedphenolic resin is mixed in the carbon nanotubes. Then, the carbon nanotubesare made into electrodes by hot-press molding after the process of milling with high speed. The surface of the carbon nanotubes electrodes is analyzed by SEM. Active red X-3B simulated waster water is disposed by carbon nanotubes catalyticelectrode (anode) and stainless steel(cathode). The influencing factors of degradation by current density, concentrationof electrolyte, systemtemperature and pH are investigated. The experimental results indicated that acidiccondition is propitious tothe degradationreaction of organicdyestuff and wastewater …

Effect Of Sintering Temperatures On Synthesis Of Mgco0.4Mn1.6O4 Positive Materials In Magnesium Ion Battery, Xiu-Ling Gao, Li-Fang Jiao, Hua-Tang Yuan, Jian-Sheng Cao, Ming Zhao, Hai-Xia Li, Yong-Mei Wang

Journal of Electrochemistry

The cathode material MgCo_0.4Mn_1.6O₄ for magnesium ion battery was synthesized by sol-gel method. The TG-DTA and XRD analyses showed that the prepared samples has simple spinel structure. Effect of annealing temperature on electrochemical properties was researched. The result shows that the sample sintered at 700℃ has the best electrochemical properties.

Electrochemical Reduction Characteristics Of Nitrobenzene At The Copper Electrode, Jin-Hong Fan, Wen-Ying Xu, Ting-Yao Gao

Journal of Electrochemistry

The electrochemical reduction characteristics and transition steps of nitrobenzene aqueous solution at the copper electrode, as well as its reduction mechanism were extensively investigatedby using the techniques such as cyclic voltammetry (CV) and linear scan voltammetry (LSV). The results showed that the reduction peaks of nitrobenzene at the copper electrode were located at 0.58 V and 1.32 V or so (vs. SCE), both acidity and alkalinesolutionsfavoredthe reduction of nitrobenzene. The adsorption of compounds followed by the reduction process, which is controlled by the mass transfer step at higher nitrobenzene concentration. In addition, the higher anaerobic degree led to faster reduction …

Adsorption Of Polyaspartic Acid From Sulphur Acid Solution On Carbon Steel And Its Corrosion Inhibition, Rong-Jing Cui, Ning Gu, Chun-Mei Li

Journal of Electrochemistry

The role of Polyaspartic acid in the corrosion inhibition of 45# carbon steel in sulphuric acid solution has been investigated by polarization curve andelectrochemical impedance spectroscopy (EIS). The influences of the concentration and the temperature of PASP on the corrosion inhibition efficiency were determined. The results indicated that the PASP as the corrosion inhibitor mainly inhibitated the anode; within the experiment temperature, the inhibitor efficiency decreased with the raising of the temperature and PASP had a good inhibiting performance at 10℃, the corrosion inhibition efficiency of PASP for carbon steel increased with the increase of the concentration of PASP when …

Research Progresses In A Flow Redox Battery, Quan-Feng Dong, Hua-Min Zhang, Ming-Gang Jin, Ming-Sen Zheng, Ya-Ding Zhan, Shi-Gang Sun, Zu-Geng Lin

Journal of Electrochemistry

As a large scale electrochemical storage device, flow redox battery in which the active materials are flowing electrolytes is different from the common batteries employing solid or gas materials as an electrode. In this paper we introduced flow redox battery in brief, reviewed its development and actual state on (study). The main problem existed in the new device was discussed when viewed with its future developments.

Nafion Emulsion Method For Fuel Cell Membrane-Electrode-Assembly Preparation, Chao-Yang Xia, Lin Zhuang, Jun-Tao Lu

Journal of Electrochemistry

A Nafion emulsion method for fuel cell membrane-electrode-assembly (MEA) preparation was reported for the first time in this paper. 5 %(by mass) Nafion alcohol solution and non-polar solvent (e.g., cyclohexane) were ultrasonicallymixed to produce Nafion emulsion. The catalyst ink prepared using the thus-obtained Nafion emulsion can be directly cast onto Nafion membrane to make MEA. This method is simple in operation, and effectively preventsthe Nafion membrane swelling, hence is suitable for large-scale application. The MEA thus-prepared showed comparable catalyst efficiencywith respect to the popular transfer-method, and the preliminary performance in room-temperature H₂/O₂ fuel cell test was satisfying.

The Research Of Nano-Sized Nio Anode Materials For Lithium Ion Batteries, Jun-Mei Yan, Jing Zhang, Yong Yang

Journal of Electrochemistry

The nano-sized NiO materials were synthesized by solid phase method and sol-gel method. The synthesis conditions were optimized by DSC and TG techniques. The sol-gel method was optimized by changing the solvent and regulating the solution's pH for preparing NiO material. The structure and morphology of the materials were also characterized by means of XRD and TEM techniques, and the electrochemical performances of the materials were studied by the galvanostatically charge and discharge experiments.

Modeling, Fabrication, And Optimization Of Niobium Cavities Final Phase: Final Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

This final report provides the activities and accomplishments of Modeling, Fabrication, and Optimization of Niobium Cavities – Final Phase. The fluid flow experiments for the etching of the superconducting cavity walls and baffle designs of phase II of the three phases has been completed leading to a MS thesis in December of 2003. Designing the experimental setup of secondary electron emission was well underway in early summer of 2003 when funding was made available for this portion of the study. By March 2004, many of the components of the experimental study reached UNLV with some assembly accomplished. The first secondary …

Application Of Nickel Foam Electrode For Electroreduction Intermediate Of Purine, Hui-Wen Yang, Xi-En Hu, Xue-Jun Wang

Journal of Electrochemistry

Nickel foam with weight uniformity, good porosity ,pore size and low resistivity as a three-dimensional cathode was used in a filter-press electrochemical reactor. The H₂SO₄ as supporting electrolyte, separator of cation ion exchange membrane, and the lead plate as an anode were used. The cyclic system consisted of electroreduction reactor, pump, store tank and ampere meter. NAU was electroreduced in the cathode chamber of the reactor. Purine intermediate was synthesized with DAU, and the results were compared with those of iron powder reduction process. A peak current in the electroreduction process was detected. The current density of …

A Preliminary Study Of Electrocrystallization Of Bismuth On Glassy Carbon, Min-Li Yang, Zhan-Jun Zhang

Journal of Electrochemistry

The electrocrystallization of bismuth on glassy carbon electrodes (GCEs) from nitrate solutions was studied by cyclic voltammetry and chronoamperometry. Cyclic voltammograms exhibit a crossover between the cathodic and anodic branches, characteristic of the formation of bismuth nuclei on GCEs, and show that the bismuth electrocrystallization on GCEs is a diffusion-controlled reaction. The current transients were analyzed with the Scharifker and the Heerman equations. With the increaseof Bi³⁺ concentration, the non-dimensional plots leaned to the theoretical curve for 3D instantaneous nucleation and growth. The overpotential dependence of nucleation and growth mechanism was also found. With the increase of overpotential, the …

Preparation And Characterization Of Mcm-41/Pvdf-Hfp Composite Microporous Polymer Electrolytes For Li-Ion Batteries, Zuo-Feng Chen, Yan-Xia Jiang, Quan-Chao Zhuang, Quan-Feng Dong, Shi-Gang Sun

Journal of Electrochemistry

MCM-41/vinylidine fluoride-hexafluropropene copolymer (PVdF-HFP) composite microporous polymer electrolytes were prepared with mixed solvent of N, N-Dimethylformamide (DMF) and acetone. The influence of MCM-41 and nano-SiO₂ on the porous structure of the microporous polymer electrolytes were studied with SEM. The results show that MCM-41 could take the place of the plasticizer in the process of making pores, and bring the preparation of microporous membranes easily. The preliminary electrochemical tests showed that the ion conductivity of composite microporous polymer electrolyte with 10% MCM-41 was about 10^-3 S cm^-1, and the performance of batteries was improved. The mesoporous MCM-41selected …

Investigation On Ru-Ti-Ir-Sn Oxide Anode Coatings For Electrolyzing Seawater, Ke Wang, Yan Han, Lei-Yuan Wang, Xiao-Ling Zhang, Yu-Pu Sun

Journal of Electrochemistry

The anode coatings of Ru-Ti-Ir-Sn oxide with various compositions were prepared by thermal decomposition. The physical and electrochemical properties of the coatings were characterized by scanning electron microscope (SEM), energy dispersive X-ray detector (EDX), accelerated life, current efficiency, anti-Mn²⁺ contamination, polarization curveandcyclic voltammetry tests. The results showed thatthe anode coating with optimized formula possessed excellent overall properties for electrolyzing seawater.

Study On Synthesis Of M-Phenoxy Benzoic Acid By Electrolysis Oxidation Method, Wei Xu, Chong-Tao Zhao

Journal of Electrochemistry

The m-phenoxy benzoic acid was synthesized by oxidation m-phenoxy toluene using Cr(Ⅵ)as oxidation media, which was prepared by electrolysis oxidation of Cr(Ⅲ)in the electrochemical bath using Nafion 417 as a diaphragm, Pb-PbO₂ as an anode and Pb as cathode. The effect factors on the electrochemical oxidation of Cr(Ⅲ)to Cr(Ⅵ)in this electrolysis were studied. Furthermore, the optimal conditions for electronic synthesis of m-phenoxy benzoic acid were also discussed.

The Synthesis, Characteristics And Performance Of Cnt Composites As Anodic Materials In Litium-Ion Battery, Quan-Feng Dong, Ming-Sen Zheng, Zhen-Cai Huang, Ming-Gang Jin, Ya-Ding Zhan, Zu-Geng Lin

Journal of Electrochemistry

As an anodic material for lithium ion battery the carbon nano-tube (CNT) and some compounds based on tin have ever been investigated intensively. The fruited progress has not been made yet, however. In this paper the composites of CNT and Sn/SnO₂ were synthesized employing two methods and characterized by SEM and XRD. And the electrochemical performance of the composites was investigated.

The Effect Of Oxidant On Structure And Properties Of Pan/Ptfe Conducting Composite Membrane, Chang-Yuan Tao, Jing Chen, Jun Du, Cai-Xin Sun

Journal of Electrochemistry

The PAn/PTFE conducting composite membrane was prepared by means of in-situ permeating chemical polymerization, with (NH₄)₂S₂O₈ and Na₃VO₄ being used as an oxidant respectively. The polymerization-growth behavior of the aniline by using different oxidant was compared. In addition, the oxidant effect on the structure and properties of conducting composite membrane was discussed. The results of SEM micrographs, pore size distribution and electrochemical methods suggested that using either oxidants could also induce the product with small pore size and dense pore structure. Compared with (NH₄)₂S₂O …

The Preparation And Performance Of The Aqueous Matrix For Molten Carbonate Fuel Cells, Hua-Xin Lin, Mo-Jie Ceng, Bao-Lian Yi

Journal of Electrochemistry

PVA matrix of MCFC was prepared from the α-LiAlO₂ powder, and polyvinylalcohol(PVA), Compared with the conventional PVB matrix, higher porosity, higher thermal weight loss and smaller maximum pore diameter were achieved for PVA matrix. Single cell was assembled with PVA matrix. At reaction gas pressure of 0.9 MPa, under reaction gas utilization of 20%, at 300 and 428.57 mA·cm^-2, the cell voltage was 0.849 and 0.739 V respectively, and the output power density was 254.7 and 316.7 mW·cm^-2 respectively, which are higher than those of the cell assembled with PVB matrix. During thermal cycles, the cell …

Instrumentation Of Ysz Oxygen Sensor Calibration In Liquid Lead-Bismuth Eutectic, X. Wu, Jian Ma, Yingtao Jiang, B. Fu, W. Hang, J. Zhang, N. Li

Mechanical Engineering Faculty Research

Liquid lead-bismuth eutectic (LBE), a good candidate for the coolant in the subcritical transmutation blanket, is known to be very corrosive to the stainless steel that transports it. Such a corrosion problem can be prevented by producing and maintaining a protective oxide layer on the exposed surface of the stainless steel. Proper formation of the oxide layer critically depends on the accurate measurement and control of the oxygen concentration in liquid LBE. An oxygen sensor calibration/measurement apparatus has been designed and built to deliberately calibrate an yttria stabilized zirconia (YSZ) oxygen sensor. A detailed description of this system with its …

High-Temperature Monitoring Of Refractory Wall Recession Using Frequency-Modulated Continuous-Wave (Fm-Cw) Radar Techniques, Bivin Varghese, C. Deconick, G. Cartee, M. Velez, Robert E. Moore, R. Zoughi

Electrical and Computer Engineering Faculty Research & Creative Works

Furnaces are among the most crucial components in the glass and metallurgical industry. Nowadays, furnaces are being operated at higher temperatures and for longer periods of time thus increasing the rate of wear on the furnace refractory lining. Consequently, there is a great need for a nondestructive tool that can accurately measure refractory wall thickness at high temperatures. In this paper the utility of a frequency-modulated continuous-wave (FM-CW) radar is investigated for this purpose.

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Iii Fourth Quarterly Report, Robert A. Schill Jr., Mohamed Trabia, William Culbreth

Transmutation Sciences Materials (TRP)

Niobium cavities are important parts of the integrated NC/SC high-power linacs. Over the years, researchers in several countries have tested various cavity shapes. They concluded that elliptically shaped cells are the most appropriate shape for niobium superconducting cavities. The surface preparation can significantly affect the secondary electron emission yields. Such yields are used in design codes. Current codes use values obtained from niobium samples cleaned by a different means at temperatures other than the operating temperature. Secondary electron emission studies on LANL surface-cleaned niobium are conducted with preliminary data presented in this report at room temperature. Soon studies will be …

Study Of 2d And 3d Optical Beam Induced Voltage Imaging Using Photoresistor Sensor, Warsito Warsito, Sri Wahyu Suciyati, Susi Harnani, Akhmad Dzakwan

Makara Journal of Technology

Study of 2D and 3D Optical Beam Induced Voltage Imaging Using Photoresistor Sensor. This article shows a method to study OBIV (optical beam induced voltage) imagerie system, that usually employ a laser scanning microscopy system. The OBIV imagerie system developed use a photoresistor sensor as a sample and simultaneously it can be used for analyzing its inhomogeneity response. Resolution of the system is still low, about 350μm due to high value of incident light diameter. The results inform that photoresistor sensors gave an optimum response if the incident light hits the center of sensible zone.

Water Quality Of Rivers And Ponds On Dki Jakarta, Diana Hendrawan

Makara Journal of Technology

Water Quality of Rivers and Ponds on DKI Jakarta. Thirteen big rivers, some small rivers, and 40 ponds spread over districts at Jakarta city are potential to support human being life. As the population is growing and the usage of stream water is increasing, the condition and quality of rivers and ponds are changing. Crowd housing can affect rivers and ponds pollution, as the people awareness about clean and healthy environment is less. Stream water pollution assessment can be done by counting the effect of pollutant to life of stream water organisms. This assessment unit could be classified into physics, …