Materials Science and Engineering Commons^™

2nd Annual Undergraduate Research Conference Abstract Book, University Of Missouri--Rolla

Undergraduate Research Conference at Missouri S&T

No abstract provided.

Analysis Of Technical Energy Losses By Using Simulation, Betrianis Betrianis, Randite Herawan

Makara Journal of Technology

Model is a representation of a system. Through model, it can be easier to forecast and control the changing of each element system. Electricity distribution is also a system. Losses are general problem that exist in a distribution network system. But with the right methods, specifically technical energy losses can be reduced in order to increase the efficiency. By making model of the distribution network, the value of technical energy losses in the whole network as well as in every line can be observed. Simulation can also be used to see all losses reduction alternatives. By comparing results from each …

Modeling Of Coupled-Tank System Using Fuzzy Takagi-Sugeno Model, Aries Subiantoro

Makara Journal of Technology

Modeling of Coupled-Tank System Using Fuzzy Takagi-Sugeno Model. This paper describes modeling of coupledtank system based on data measurement using fuzzy Takagi-Sugeno model. The fuzzy clustering method of Gustafson- Kessel algorithm is used to classify input-output data into several clusters based on distance similarity of a member of input-output data from center of cluster. The formed clusters are projected orthonormally into each linguistic variables of premise part to determine membership function of fuzzy Takagi-Sugeno model. By estimating data in each cluster, the consequent parameters of fuzzy Takagi-Sugeno model are calculated using weighted least-squares method. The resulted fuzzy Takagi-Sugeno model is …

Design Of Induction Motor Drive Without Velocity Sensor Using Current Vector Controller With Full And Reduced Observer Moving To Dq Axis, Ridwan Gunawan, Feri Yusivar, Wahidin Wahab, Zuhal A. Kadir

Makara Journal of Technology

Design of Induction Motor Drive Without Velocity Sensor Using Current Vector Controller with Full and Reduced Observer Moving to DQ Axis. The observer is used in estimation velocity sensor usually in α-β axis, therefore this situation will need an extra transformation when we want to add compensator because the flux model is in direct and quadrature-axis dq. Every used the transformation to make possible emerge an error. So in this simulation is used a method to estimate the velocity of induction motor drive with observer that is moved to dq-axis. The model of actual motor used is in alfa-beta axis, …

Effect Of Firing Temperature And Holding Time On Characterization Of Al/Sic Metal Matrix Composites Produced By Pressureless Infiltration., Anne Zulfia, Myrna Ariati

Makara Journal of Technology

Effect of Firing Temperature and Holding Time on Characterization of Al/SiC Metal Matrix Composites Produced by Pressureless Infiltration. The production of Al-SiC metal matrix composite can be carried out by pressureless metal infiltration processs (PRIMEX). The experiment was conducted using aluminium AC2B ingot as a matrix and 50%Vf SiC powder as a reinforcement which is mixed with 10% Mg powder for wetting agent. The variables of this experiment are holding time and firing temperature to investigate the effect of these conditions on mechanical properties of Al-SiC metal matrix composites. Holding time was conducted for 2,5,8,10,12 hours and firing temperatures was …

Development Of Fiber-Optic Humidity Sensor Probe With Gelatin Cladding, Akhiruddin Maddu, Kun Modjahidin, Sar Sardy, Hamdani Zain

Makara Journal of Technology

Development of Fiber-Optic Humidity Sensor Probe with Gelatin Cladding. Humidity sensor based on optical fiber with gelatin cladding has been developed. In this humidity sensor probe, the origin cladding of optical fiber is replaced by gelatin coating as humidity sensitive cladding. Testing of the optical fiber sensor probe was conducted by measuring of light intensity transmitted on the optical fiber probe for each variation of different humidity treatments. Response of the optical fiber sensor probe measured from 42%RH to 99%RH, the results show an optical transmission curve varied with relative humidity (RH). Optical transmission in the optical fiber probe increase …

On The Performance Of Imt-2000 Communication Link Based On Stratospheric Platforms, Iskandar Iskandar, Shigeru Shimamoto

Makara Journal of Technology

A new means for providing wireless communication has been currently proposed. It is based on aerial vehicle known as High Altitude Platform or Stratospheric Platforms (SPF). The SPF will be operated at an altitude of 17-22 km above the ground. Therefore, the channel condition may be different compared with those of the conventional terrestrial or satellite wireless channel. In this paper, the channel propagation characteristic of such a system is firstly investigated by means of ray tracing algorithm. We emphasize our investigation in a typical urban environment, in which the mobile users mostly exist. We developed building block model for …

Modification Of Bonding Strength Test Of Wc Hvof Thermal Spray Coating On Rocket Nozzle, Bondan T. Sofyan, Haposan J. Pardede, Marizki Stefano, Edi Sofyan

Makara Journal of Technology

Modification of Bonding Strength Test of WC HVOF Thermal Spray Coating on Rocket Nozzle. One way to reduce structural weight of RX-100 rocket is by modifying the nozzle material and processing. Nozzle is the main target in weight reduction due to the fact that it contributes 30 % to the total weight of the structur. An alternative for this is by substitution of massive graphite, which is currently used as thermal protector in the nozzle, with thin layer of HVOF (High Velocity Oxy-Fuel) thermal spray layer. This paper presents the characterization of nozzle base material as well as the modification …

Hybrid Identification System With Arx And Fast Fourier Transform In Application Of A Quarter Of Vehicle Half Active Suspension, Noveri Lysbetti M, Antonius R.

Makara Journal of Technology

Hybrid Identification System with ARX and Fast Fourier Transform in Application of a Quarter of Vehicle Half Active Suspension. In a control system problem, identification system mechanism is a absolute thing, especially in adaptation controlling to disturbance changing. For that case, is needed an identification method which can identify the changing of disturbance in that system. The aim of this research is to give an alternative in system/plant identification which is a combination (hybrid) of ARX and Fast Fourier Transform. So, it is needed an algorithm design for identification process. In this case, the designed algorithm will be implemented in …

College Of Engineering Senior Design Competition Fall 2005, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

Simultaneous Treatment Of Organic (Phenol) And Heavy Metal (Cr6+ Or Pt4+) Wastes Over Tio2, Zno-Tio2 And Cds-Tio2 Photocatalysts, Slamet Slamet, R. Arbianti, Daryanto Daryanto

Makara Journal of Technology

Simultaneous Treatment of Organic (Phenol) and Heavy Metal (Cr6+ or Pt4+) Wastes over TiO2, ZnO-TiO2 and CdS-TiO2 Photocatalysts. Treatment of heavy metal (Cr6+ and Pt4+) and organic (phenol) wastes has been studied using the relatively new method, i.e. simultaneous photocatalytic process over TiO2 photocatalysts in the batch photoreactor. Following the photocatalytic reduction of the heavy metal wastes, recovery of Cr and Pt was carried out by precipitation and leaching method, respectively. The experimental results show that in the simultaneous photocatalytic system, there is a synergism effect between the photocatalytic reduction of heavy metal waste (Cr6+ or Pt4+) and the oxidation …

Development Of Low Frequency Vibration Method Of Direct-Write Deposition Relevant To Layer Manufacturing Application, Susilo Adi Widyanto, Alva Edy Tontowi, Jamasri Jamasri, Heru Santosa Budi Rochardjo

Makara Journal of Technology

The research of deposition process is the first step in development process of multi materials selective laser sintering. The deposition process enables to settle multi materials powder in horizontal formation on one layer. In this research we use low frequency (70 - 200Hz) to vibrate a hopper nozzle in which powder is settled. The research method consists of two steps, the first step is to determine flow-ability parameters and the second is to join flow ability parameter with other parameters such that the line width can be controlled. The results show that the line width depends on uniformity of particle …

Design Of Product Placement Layout In Retail Shop Using Market Basket Analysis, Isti Surjandari, Annury Citra Seruni

Makara Journal of Technology

Retailing is an industry with high level of competition. It is a customer-based industry which depends on how it could be aware of what the customers’ needs and requirements are. One technique most used in supermarkets is the mix merchandise. The purpose of this paper is to identify associated products, which then grouped in mix merchandise with the use of market basket analysis. This association between products then will be applied in the design layout of the product in the supermarket. The process of identifying the related products bought together in one transaction is done by using data mining technique. …

Production Hydrogen And Nanocarbon Via Methane Decomposition Using Ni-Based Catalysts. Effect Of Acidity And Catalyst Diameter, Widodo W. Purwanto, M. Nasikin, E. Saputra, L. Song

Makara Journal of Technology

Objectives of this research are mainly to study impacts of acidity strength (by varying amount of precipitant and loading Al-Si) and the effect of nickel particle size (by varying calcinations temperature) on decomposition reaction performances. In this research, high-nickel-loaded catalyst is prepared with two methods. Ni-Cu/Al catalysts were prepared with co-precipitation method. While the Ni-Cu/Al-Si catalyst were prepared by combined co-precipitation and sol-gel method. The direct cracking of methane was performed in 8mm quartz fixed bed reactor at atmospheric pressure and 500-700°C. The main results showed that the Al content of catalyst increases with the increasing amount of precipitant. The …

Design And Implementation Of 1-2 Ghz Stepped Frequency Gpr For Buried Metal Detection, Joko Suryana, Andriyan B. Suksmono, Tati R. Mengko

Makara Journal of Technology

Design and Implementation of 1-2 GHz Stepped Frequency GPR for Buried Metal Detection. In this paper, we describe the design and realization steps of 1 – 2 GHz SFGPR (Stepped Frequency Ground Penetrating Radar) transceiver for metal detection under the ground. Before using prototyped GPR for detecting the metal under the ground, several of calibration processes must be performed, namely phase calibration and monocycle pulse waveform calibration. After completing the calibrations, this prototyped GPR would be ready for detecting a hidden object such as a metal plate 5 cm under the ground in our small test range size 25 cm …

Synthesis Of Fuel Cell Membrane: Copolymerization Of Styrene On Etfe Film By Grafted Pre-Irradiation, Yohan Yohan, Rifai M. Nur, Lilik Hendrajaya, E. S. Siradj

Makara Journal of Technology

Synthesis of Fuel Cell Membrane: Copolymerization of Styrene on ETFE Film by Grafted pre-Irradiation. Preirradiation Grafting styrene monomer on ETFE film has been prepared. Research has been performed by γ-ray radiation at various total dose from 2.5 – 12.5 kGy and various dose rate from 1.3 – 1.9 kGy/hour. Irradiated copolymer is then grafted by styrene monomer in various solvent: ethanol, 2-propanol, and toluene, various concentration from 20 – 70% volume, various temperature from 50 – 90oC, and various grafting time from 2 – 12 hours. The results showed that percent of grafting is increase with increase of total dose …

Design Of Generating Dual Frequency Operation For Triangular Microstrip Antenna Using Electromagnetic Coupling, Indra Surjati, Eko Tjipto Rahardjo, Djoko Hartanto

Makara Journal of Technology

Design of Generating Dual Frequency Operation for Triangular Microstrip Antenna Using Electromagnetic Coupling. A new design is proposed in this paper by applying a pair of slits using a microstrip feed line. Therefore the microstrip line feeding system is electromagnetically coupled to the patch. The antenna works at two different frequencies in the range from 2 GHz to 4 GHz (S band frequency). The results of the simulation shows that the dual frequency operation can be created when the slit width is 1 mm and the height of the slits ranges from 10 mm to 14 mm with inter slit …

Nonlinear Model For Reinforced Concrete Under Cyclic Loading, Aly Said, M. Elmorsi, M. Nehdi

Civil and Environmental Engineering and Construction Faculty Research

Most of the available shear models for reinforced concrete rely on empirical formulations. In this study, a rational shear stress function is used to define the shear stress–strain envelope for reinforced concrete. Cyclic rules are proposed to define the loading, unloading and reloading relationships for reinforced concrete under shear stress reversals. A normal stress function describing the cyclic relationship of concrete under axial stress is also introduced. The proposed functions are verified using experimental data of reinforced concrete panels tested under monotonic and cyclic loading. Subsequently, the normal and shear stress functions along with their cyclic rules are integrated in …

Sub-Surface Corrosion Research On Rock Bolt System, Perforated Ss Sheets And Steel Sets For The Yucca Mountain Repository — Quarterly Technical Report No. 3, Dhanesh Chandra, Jaak J.K. Daemen

Publications (YM)

This report encompasses the work done for third quarter in accordance to cooperative agreement of UCCSN for the Task 019 “Subsurface Corrosion Research on Rock Bolt System, Perforated SS Sheets and Steel Sets for the Yucca Mountain Repository”, the objective of which was proposed earlier, to conduct corrosion research and predict the durability of rockbolts and other underground metallic roof supports. We have recently started working on oxidation tests using Thermogravimetric Analyzer (TGA), stress corrosion cracking/hydrogen embrittlement studies on rock bolts, other support materials including bench mark materials. In this quarterly report we will discuss “Dry” oxidation of steels and …

Study Of 2d And 3d Optical Beam Induced Voltage Imaging Using Photoresistor Sensor, Warsito Warsito, Sri Wahyu Suciyati, Susi Harnani, Akhmad Dzakwan

Makara Journal of Technology

Study of 2D and 3D Optical Beam Induced Voltage Imaging Using Photoresistor Sensor. This article shows a method to study OBIV (optical beam induced voltage) imagerie system, that usually employ a laser scanning microscopy system. The OBIV imagerie system developed use a photoresistor sensor as a sample and simultaneously it can be used for analyzing its inhomogeneity response. Resolution of the system is still low, about 350μm due to high value of incident light diameter. The results inform that photoresistor sensors gave an optimum response if the incident light hits the center of sensible zone.

Water Quality Of Rivers And Ponds On Dki Jakarta, Diana Hendrawan

Makara Journal of Technology

Water Quality of Rivers and Ponds on DKI Jakarta. Thirteen big rivers, some small rivers, and 40 ponds spread over districts at Jakarta city are potential to support human being life. As the population is growing and the usage of stream water is increasing, the condition and quality of rivers and ponds are changing. Crowd housing can affect rivers and ponds pollution, as the people awareness about clean and healthy environment is less. Stream water pollution assessment can be done by counting the effect of pollutant to life of stream water organisms. This assessment unit could be classified into physics, …

Time Domain Characterization Of 1-2 Ghz Circular-Ended Bowtie Antenna Using Normalizad Impulse Response, Joko Suryana, Andriyan B. Suksmono, Tati R. Mengko

Makara Journal of Technology

Time Domain Characterization of 1-2 GHz Circular-ended Bowtie Antenna Using Normalizad Impulse Response. Frequency domain analysis is a powerful and compact tool for characterizing the antenna parameters such as gain, radiation pattern and the impedance as a function of frequency. However, if time or space is a major concern, such as in the GPR appication, the time domain analysis would be a very important tool due to their unique capability for determining the echo delay and range profile of target image. In this paper, we will describe the classical theory of system characterization in time domain, and then also propose …

3d Modelling With Linear Approaches Using Geometric Primitives, Mochammad Zuliansyah

Makara Journal of Technology

In this paper, we study linear approaches for 3D model acquisition from non-calibrated images. First, the intrinsic and extrinsic camera calibration is taken into consideration. In particular, we study the use of a specific calibration primitive: the parallelepiped. Parallelepipeds are frequently present in man-made environments and naturally encode the affine structure of the scene. Any information about their euclidean structure (angles or ratios of edge lengths), possibly combined with information about camera parameters is useful to obtain the euclidean reconstruction. We propose an elegant formalism to incorporate such information, in which camera parameters are dual to parallelepiped parameters, i.e. any …

Dipole Magnetization Effect To Kerosene Characteristics, Mochamad Chalid, Nelson Saksono, Adiwar Adiwar, Nono Darsono

Makara Journal of Technology

Dipole Magnetization Effect to Kerosene Characteristics. Investigation of kerosene characteristics has been done by ex-situ dipole magnetization. The results show that magnetization technique can be able to influence kerosene characteristics. Polarity and viscosity of the kerosene are observed by measuring refractive index and viscosity. An hour of 4330 Gauss flux magnetic will increase refractive index from 1.447 to 1.449 and decrease the viscosity from 1.278 to 1.256. Those changing support de-clustering occurrence and polarity increment of kerosene molecule. Gas chromatography and infrared result show that those changing do not alter kerosene structure and composition.

Synthesis Dibenzyl Terephthalate Through Depolimerization Of Poly (Ethylene Terephthalate) As Alternative Of Waste Plastics Recycling, Suwardi Suwardi, Crys Fajar Partana, Agus Salim, Dyah Anitasari

Makara Journal of Technology

Synthesis Dibenzyl Terephthalate Through Depolimerization of Poly(ethylene terephthalate) as Alternative of Waste Plastics Recycling. Synthesis dibenzyl terephathalate were done through PET degradation by refluxing in benzyl alcohol at 145oC temperature for 20, 24, and 28 hours in the presence of zinc acetate catalyst. The result of degradation was purified by recristalization in methanol and then melting point (mp), FTIR, 1H NMR spectra, and TLC spot were determined. The melting point of product degradation for 28 hours was 98-99 oC. Based FTIR spectra known that compunds of product degradation have OH, C=O, C-O, CH, monosubstituted benzene, disubstituted benzene groups, while on …

Flexi Radio Base Station (Rbs) Performance Analysis Of Voice And Trafic On Kota 2 Jakarta Barat Base Station Control (Bsc), Mushfar Ferdian, Fitri Yuli Zulkifli

Makara Journal of Technology

Flexi Radio Base Station (RBS) Performance Analysis of Voice and Trafic on Kota 2 Jakarta Barat Base Station Control (BSC). The CDMA 2000 technology uses circuit switch method to handle voice traffic and packet switch method to handle data traffic between the user and RBS (Radio Base Station). These two parameters can be used to measure performance of the network generally, so it is necessary to optimize them. This paper analyze the performance of RBS by measuring its parameters such as set up failure ratio, drop ratio, and occupancy. Furthermore, the traffic increment is calculated too in order to provide …

Sub-Surface Corrosion Research On Rock Bolt System, Perforated Ss Sheets And Steel Sets For The Yucca Mountain Repository — Quarterly Technical Report No. 2, Dhanesh Chandra

Publications (YM)

This report encompasses the work done for second quarter in accordance to cooperative agreement of UCCSN for the Task 019 “Subsurface Corrosion Research on Rock Bolt System, Perforated SS Sheets and Steel Sets for the Yucca Mountain Repository”, the objective of which was proposed earlier, to conduct corrosion research and predict the durability of rock-bolts and other underground metallic roof supports. We have recently started working on oxidation tests using Thermogravimetric Analyzer, stress corrosion cracking/hydrogen embrittlement studies on rock bolts, other support materials including bench mark materials. In this quarterly report we will discuss “Dry” oxidation of steels and other …

Fuel Injection System For One Cylinder Motor Cycle Engine, Bambang Sugiarto

Makara Journal of Technology

Fuel Injection System for One Cylinder Motor Cycle Engine. Fuel injection has been developed for many years. But its common application is limited on car’s engine. With many reason fuel injection systems in motorcycle one cylinder engine has not been widely used yet. Fuel Injection System allows the amount of fuel, injected to be controlled appropriate to engine parameters such as engine speed, amount of air inducted to cylinder, temperature, for each cycle, over the entire engine operating conditions. This fuel injection research is done to find out the Volumetric Efficiency of the intake manifold system, the amount of fuel …

Influence Of Connection Placement To The Behavior Of Precast Concrete Exterior Beam-Column Joint, Elly Tjahjono, Heru Purnomo

Makara Journal of Technology

Influence of Connection Placement to the Behavior of Precast Concrete Exterior Beam-Column Joint. This paper presents an experimental study on the influence of connection placement to the behaviour of exterior beamcolumn joint of precast concrete structure under semi cyclic loading. Four half-scale beam-column specimens were investigated. Three beam-columns were jointed through connection that are placed in beam-column joint region and the forth is connected at the plastic hinge potensial region of the beam. Crack patterns, strength, stiffness and ductility of the test specimens have been evaluated. The test result indicated that all beam-column specimens show good ductility behavior.

Optic Properties On Aggase2 Polycristal Fabrication, A. Harsono Soepardjo, I Dewa Made Janusetiawan

Makara Journal of Technology

Optic Properties on AgGaSe2 Polycristal Fabrication. Polycristal AgGaSe2, is compound (I-III-VI2) a semiconductor as basic material for thin film for solar cell. Polycristal was succesfully grown using Bridgmann Method, heated on sequential temperature treatment until 850°C and cooled down slowly until room temperature. Results observed were in the form of ingot (bars) with more or less 3 cm length and 13 mm in diameter. By using X-Ray Fefraction, composition obtained of each element (weight %) was Ag = 29,3996 %, Ga = 36,8123 % and Se = 30,29 % while using X-Ray Difraction lattice parameter obtained/calculated a = 4,4112 Å, …