Materials Science and Engineering Commons^™

Electrochemistry And Electrocatalysis Of A Novel Μ-Oxamido Copper(Ⅱ) Binuclear Complex, Gui-Lian Gao, Guo-Bao Li, Qiu-Xia Yang, Xue-Lin Wang

Journal of Electrochemistry

In this paper, the cyclic voltammetric and spectroelectrochemical behaviors of μ-oxamido Copper(Ⅱ) Binuclear Complex (deCu) in PBS were studied. Cyclic voltammograms of this complex in PBS (pH=9) exhibited two reductive peaks (E_pc1 =-0.25 V, E_pc2 = -0.50 V) at hanging mercury drop electrode(HMDE), peaks at -0.50 V and -0.25 V corresponded to the reduction of ligand and copper(Ⅱ) complex, respectively. The spectroelectrochimical experiments showed that there was a new absorption band at 440 nm, and the absorption peaks at 270 nm, 280 nm red shifted to 300 nm, 310 nm under potential of -0.75 V. It was meant …

The Mechanism Of Electrocatalytic Reduction Of Oxygen On Manganese Dioxide, Yu-Liang Cao, Han-Xi Yang, Xin-Ping Ai, Li-Fen Xiao

Journal of Electrochemistry

The oxygen electroreduction on the MnO₂ electrode was investigated by analysis of the polarzation properties of oxygen reduciton and its dependence on MnO₂ discharge state, in combination with the characterization of discharge intermediate and the kinetic parameters of the oxygen reduction. Based on the experimental observation and mechanistic analysis, it was suggested that the reduction of oxygen was closely related to the discharge behaviors of MnO₂. When MnO₂ was electrochimically reduced to MnOOH, it was immediately oxidized by oxygen molecules. Thus the oxygen reduction proceeds through continuous oxidation of the discharge product of MnO_{2 …}

Oxidation Behavior Of Zr-Cu-Al-Ni Amorphous Alloys In Air At 300～500℃, H. H. Hsieh, W. Kai, T. G. Neih, Y. Kawamura

Journal of Electrochemistry

The oxidation behavior of the Zr- based bulk amorphous alloy (BMG; Zr-30Cu-10Al-5Ni in at.%) was studied in dry air over the temperature range 300～500 ℃. The kinetic results indicated that the amorphous alloy oxidized linearly at 300 ℃, while the parabolic oxidation was observed at 350～425 ℃, and the oxidation behavior at 500 ℃ was irregular and complicated. In general, the scales formed on the surface of the amorphous alloy were temperature-dependent, consisting of tetragonal-ZrO₂ at 300 ℃, and of mostly tetragonal-ZrO₂ as well as minor amounts of monoclinic-ZrO₂ and CuO at T ≥ 350 ℃.

Electrochemical Monitoring On The Deactivation Of A Metallic Oxide Anode, Li-Kun Xu, Shi-Zhe Song, Ting-Yong Wang, Guang-Zhang Chen

Journal of Electrochemistry

The process of accelerated life test of an IrO₂/Ta₂O₅ coated titanium anode was monitored using cyclic voltammetry and electrochemical impedance spectroscopy. The vatiation with electrolysis time of anodic voltammetric charge Q^*, the double layer capacitance C_dl,the oxide film resistance R_f and the charge transfer resistance R_ct for oxygen evolution was measured. A deactivation mechanism was proposed based on the observation results.

Synthesis And Electrochemical Characteristics Of Nickel-Based Complex Oxide LiANi0.78Co0.2Cd0.02O2, Rong-Zhong Yuan, Mei-Zhen Qu, Zuo-Long Yu

Journal of Electrochemistry

The nickel-based complex oxide Li_aNi_0.78Co_0.02O₂ cathode materials for lithium-ion rechargeable batteries was synthesized by the improved solid-state reaction method with LiOH·H₂O, ball-like Cd-doped Ni(OH)₂ and Co₂O₃ as raw materials. The analysis ICP-AES proved that the as-prepared compounds were near the stoichiometric form. The XRD, SEM and electrochemical characteristics testing were also carried out. The results showed that the complex cathode material Li_aNi_0.78Co_0.2Cd_0.02O₂ has layered structure, homogeneous surface distributions,uniform particles with good crystal morphology as well as stable electrochemical …

The Study On The Synthesis And Electrochemical Property Of K2Feo4, Yong-Long Wang, Ning Zhou, Shi-Hai Ye, Xue-Ping Gao, Feng Wu, Zuo-Xiang Zhou, De-Ying Song

Journal of Electrochemistry

The synthesis,characterization and electrochemical property of K₂FeO₄ for positive materal of lithium ion battery were studied. K₂FeO₄ with low purity was gained through the reaction of KCIO and Fe(NO₃)₃ in KOH solution and after recrystalization the purity of K₂FeO₄ reached 97%～98%. The methods of XRD and FTIR were used to measure the structure of K₂FeO₄ and its initial discharge performance was tested.

An Eqcm Study Of Water Adsorption And Oxidation On Pt Electrodes In Sulfate Acid Sulotions, Heng Lin, Sheng-Pei Chen, Jin-Mei Lin, Ai-Lan Lin, Guo-Liang Chen

Journal of Electrochemistry

Simultaneous frequency and current responses during potential cycling of Pt electrode were measured in 0.1 mol·L^-1 H₂SO₄ solution by using EQCM. Quantitative analysis of the mass change revealed that the increase of mass in the hydrogen and double-layer regions in a positive-going potential scan was due to water adsorption on the Pt electrode, further calculation indicated that water molecules adsorbed on Pt electrode in the double-layer regions through a low discharge quomodo .The EQCM studies provided quantitative results of surface mass variation during water adsorption and oxidation,and have thrown new light in elucidating the structure of …

Synthesis By Complexation Processes And Characterization Of Lini0.8Co0.2O2 Cathode Materials, Jing Liu, Zhao-Yin Wen, Zhong-Hua Gu, Xiu-Jian Zhu, Zu-Xiang Lin

Journal of Electrochemistry

The layered LiNi_0.8Co_0.2O₂ compound, which has been of great interest for lithium ion batteries, was prepared at low temperatures by calcining a complex precursor at different temperatures. The physical properties of the synthesized cathode materials were discussed in the light of structural (XRD). The charge and discharge cycling of the cells containing the synthesized oxide as the positive electrode in conjunction with lithium metals and employing a non-aqueous electrolyte showed that LiNi_0.8Co_0.2O₂ treated at 900 ℃ exhibited excellent performances. The first discharge capacity of LLiNi_0.8Co_0.2O_{2 …}

Electroreduction Of Cd(Ⅱ) In Dmso And Complexation Of Cd(Ⅱ) With Coumarin Derivates, Ji-Guo Song, Hua-Can Song, Qi-Qin Yang, Yi-Wen Chen, Zun-Le Xu

Journal of Electrochemistry

Cadmium p-toluenesulfonate was synthesized and tested electrochemically for the first time. This salt can lose all the hydrated water easily and the dehydrated salt do not deliquesce in the air.Hence,the cadmium p-toluenesulfonate is suitable for the electrochemical studies in organic solvents.When the Cd(Ⅱ) reduced on Pt electrode in Cd(p-CH₃C₆H₄SO₃)₂+TBAP+DMSO, underpotential deposition of cadmium occurred at first, and then cadmium deposited. 4-Methyl-7-hydroxylcoumarin and 3-aminocoumarin coordinate with Cd(Ⅱ) respectively, as a result the reductive potentials of Cd(Ⅱ) moved to the negative direction.

Mechanistic Study Of Oxidation Of Hypophosphite On Pt Electrodes By Sniftirs, Tai-Xiang Jiang, Hui-Huang Wu

Journal of Electrochemistry

The oxidation of hypophosphite on a polycrystalline platinum electrode was studied by SNIFTIRS and cyclic voltammetry, the in-situ IR spectra were analyzed as a function of Pt electrode potentials in the solution of 0.5 mol/L H₂SO₄+0.1 mol/L NaH₂PO₂. It was found that the dissociative adsorption of hypophosphite ions occurs on Pt surface, and the oxidation product is H₃PO₄, rather than H₂PO₃^- which was considered to produce on Ni electrodes, thereby a new insight into mechanism of hypophosphite oxidation on Pt in acidic media was …

Nano-Sized Cobalt-Based Oxides As Negative Electrode For Lithium-Ion Batteries, Feng Huang, Zheng-Yong Yuan, Yun-Hong Zhou, Ju-Tang Sun

Journal of Electrochemistry

Nanosized cobalt-based oxide (Co₃O₄, CoB_1.36O_2.8 and CoB_0.5Al_0.1O_1.5) samples were prepared by rheological phase method and were tested as anodes in secondary lithium batteries. The cells were cycled between 0.01V and 3.00 V. The best electrochemical performance was obtained from the Co₃O₄ cell, which retained 95% of its initial capacity (931 mAh/g) after 30 cycles. The doping of B, Al reduced the reversible capacity during the first discharge/charge cycle, and the quantity of reversible capacity reduced with B, Al increasing. The modifying structures at difference …

Steady State Simulation Of Ysz Intermediate-Temperature Fuel Cell, Zi-Jing Lin, Ye Gu, Xiao-Hua Zhang

Journal of Electrochemistry

With a coupled 2D electrochemical and thermal modeling software, the characteristics of the steady state operation of the intermediate-temperature fuel cell with thin yttria-stabilized zirconia(YSZ) electrolyte was analyzed. The parameters of I-V equation were obtained from fitting the experiment results and the choice of grid points was determined by balancing the accuracy requirement and computational efficiency. The temperature fields at different operation circumstances such as flow designs, material choices for interconnect, were examined. The dependences of the output power and cell efficiency on the operating voltage at different temperatures were studied. Based upon the analysis of the temperature profile, it …

Preparation And Performance Of Lifeo2 Coated Nickel Oxide Cathode For Molten Carbonate Fuel Cells, Chun-Ming Wang, Fei Li, Ke-Ao Hu

Journal of Electrochemistry

A novel cathode for molten carbonate fuel cells was prepared by coating LiFeO₂ over the surface of porous NiO cathode by a simple combustion process. The analytical results of X-ray diffraction (XRD), energy dispersive analysis of X-ray (EDAX), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) indicated that the LiFeO₂ coating on the surface of NiO particles consisted of nonometer-sized LiFeO₂ grains and sintered tightly with the NiO particles. The LiFeO₂ coating dramatically reduced the contacting area of NiO with the carbonate melts, thus the solubility of NiO in the carbonate melts was decreased. Meanwhile, …

Review Of Mathematical Model For Proton Exchange Membrane Fuel Cell, Shan-Hai Ge, Bao-Lian Yi, Hua-Min Zhang

Journal of Electrochemistry

In the review with 49 references, the mathematical models for proton exchange membrane fuel cell (PEMFC) were summarized. The mechanistic model and empirical model were introduced. Transfer in the membrane, catalyst layer, diffusion layer and flow field of PEMFC were described. The importance of water and heat management was analyzed. The dimension, complexity and solving methods of the PEMFC model were discussed. The importance and validity to develop a model with time dimension are put forward.

Electrocatalytic Oxidation Of Formic Acid On Molybdate-Modified Platinum Electrode, Jun-Hua Du, Xue-Hui Xu, Hong Li, Hong-Yu Cheng, Wei-Shan Li

Journal of Electrochemistry

The electrochemical behavior of molybdates on a platinum electrode in H₂SO₄ solutions with different H₂SO₄ concentrations was studied by cyclic voltammetry and double chronoamperometry. Molybdates were reduced to adsorb hydrogen molybdenum bronzes on the platinum electrode in H₂SO₄ solutions during cathodically potential sweep. The hydrogen molybdenum bronzes were oxidized to different forms of hydrogen molybdenum bronzes with less hydrogen, depending on the H₂SO₄ concentration. Platinum electrode was modified by these hydrogen molybdenum bronzes. However, this modified electrode was not stable in H₂SO₄ solutions. The modified …

Manufacture Of 1 Kw Molten Carbonate Fuel Cell Stack, Sheng Sui, Xin-Jian Zhu, Zheng-Yu Fan, Guang-Yi Cao

Journal of Electrochemistry

A molten carbonate fuel cell stack with an active area of 240 mm×140 mm consisted of 30 cells. The gas feed system works via interior manifolds, and the stack placed in a couple of self-chest, coupled with a heater at the bottom and other fours surrounded,to keep uniformity of temperature.Under ambient pressure and 650 ℃, fed with hydrogen and air as anode and cathode gases respectively, the stack gave a current density of 150 mA/cm² at an average cell voltage of 0.7 V. The peak output of the stack was 1.06 kW during its performance of 300 h.

Ionic Conduction In Ba0.95Ce0.9Y0.1O3 - Α Solid Oxide And Its Performance In Fuel Cell, Gui-Lin Ma, Ding-Xian Jia, Li-Gan Qiu, Hui Shi, Rong Chen

Journal of Electrochemistry

Using Ba_0.95Ce_0.9Y_0.1O_3-α as a solid electrolyte and porous platinum as electrodes,hydrogen and oxygen concentration cells and hydrogen-air fuel cell were constructed, respectively. Electromotive forces (MEFs) of the gas concentration cells and I-V characteristics of the fuel cell were detdrmined in the temperature range of 600～1 000 ℃. The Ba_0.95Ce_0.9Y_0.1O_3-α exhibited almost the pure protonic conduction under hydrogen gas,and a mixed conduction of oxide-ion and electron hole with oxide-ion transport number of 0.3～0.5 under oxygen gas. It exhibited a mixed conduction of proton and oxide-ion with the …

Synthesis And Characterization Of Lini0.8-XAlXCo0.2O2 As Cathodes For Lithium-Ion Batteries, Jun Zhang, Zhong-Kao Jin, Qing-He Yang, Qing-Mei Song, Xiao-Hua Ma, Xiang-Fu Zong

Journal of Electrochemistry

Single-phase solid solution of LiNi_0.8-xAl_xCo_0.2O₂ (0≤ x <0.1)had been synthesized and characterized by X-ray diffraction(XRD) and scanning electron microscopy (SEM). Their electrochemical performance was examined by charge-discharge cycling. The LiNi_0.71Al_0.09Co_0.2O₂ compound showed a discharge capacity of 152 mAh/g after 20 cycles that corresponds to 97.4% capacity retention. The beneficial effect of co-doping with Al and Co elements was corro-borated by slow scanning cyclic voltammograms(SSCV), electrochemical impedance spectrum (EIS) and differential scanning calorimetry (DSC) data on charged cathodes. These results show that the 2D-character of the crystal lattice was stabilized by co-doping with Al and Co, the phase transitions that occur during deintercalation or intercalation of Li-ions were significantly suppressed, …

Optimum Of Catalyst Layers For Direct Methanol Fuel Cells, Jun Zhang, Lei Li, Li Xu, Yu-Xin Wang

Journal of Electrochemistry

The performances of membrane electrode assemblies (MEAs)with various Pt loading were compared. The amount of Nafion in a catalytic layer was optimized, and the effect of Nafion loading on the resistance of MEAs was investigated with ac impedance spectroscopy. For a MEA with both Pt 4 mg/cm² in the anode and the cathode, suitable Nafion loading was 21.4 wt% in the anode. With 21.4 wt% Nafion loading in the cathode, the Direct Methanol Fuel Cells(DMFC) showed the highest performance at high current density. While, the DMFC performances came down, as Nafion loading increasing,for ohm and concentration polarization.

Modeling And Simulation Of The Chemical Etching Process In Niobium Cavities, Qin Xue

UNLV Theses, Dissertations, Professional Papers, and Capstones

Niobium Cavities are important parts of the integrated NC/SC high-power linear accelerator (linac) that can accelerate over 100 mA of protons to several GeV. Surface finish of the niobium cavity plays an important role of achieving the best performance of niobium cavity. The chemical etching techniques have been widely used.

Chemical etching of the inner surface of the cavity is achieved by circulating acid through it. The acid interacts with the surface and eliminates imperfections. During the etching process, a pipe with baffles is inserted within the cavity to direct the flow along the surfaces.

A 2-D, axisymmetric, steady state, …

Electrosynthesis Of Glyoxylic Acid In A Cooled Cathode Reactor, Jin-Hong Fan, Jun Li, Xue-Yun Chen, Wei Li, Hao-Qi Gao

Journal of Electrochemistry

Glyoxylic acid was produced by electroreduction of oxalic acid in a well designed cooled cathode reactor. The cathodic and anodic electrolytes were super-saturated oxalic acid and hydrochloric acid aqueous solutions separated by a super-acid ion-exchange membrane. The current efficiency and time-space yield of glyoxylic acid were studied under different temperatures of cathode and electrolyte, current densities, materials of cathode. With the cooled cathode reactor, the energy consumption was reduced and higher oxalic acid concentration was available in solution, so that current efficiency was improved. The results indicated that the average time-space yield of glyoxylic acid was about 0.032 kg·dm^{-3 …}

Development Of 200～500 W Portable Proton Exchange Membrane Fuel Cell Power System, Li-Qing Hu, Li-Rong Zhou, Zheng Li, Jian-Wei Xia, Ming-Zhu Fu, Xin Wu, Yun Zhu

Journal of Electrochemistry

The Properties of the Portable PEM Fuel Cell Power Source are very unique compared with the common primary or rechargeable electro-chemical battery. This paper describes the In this work, of the 200～500 W portable PEM fuel cell power system, was developed. The system mainly composed of four subsystem: 1)Fuel cell stack; 2)Air delivery; 3)Hydrogen source; 4)Heat dissipation and system control.

Electrocatalytic Oxidation Of Formaldehyde On The Proline Film Modified Electrode, Yu-Rong Ma, Qiu-Xia Yang, Guo-Bao Li, Zheng-Kai Xi, Xue-Lin Wang

Journal of Electrochemistry

The proline film modified electrode and its electrochemical behavior was studied by cyclic voltammetry and spectroelectrochemistry. After incorporation of Ni(Ⅱ), the cyclic voltammograms of the proline Ni(Ⅱ) film electrode exhibited a typical redox peak, which appeared at potential of 0.52 V anodic and 0.44 V cathodic in NaOH. The formal potentials E' were linearly dependent on the pH, and the peak currents ip were linearly dependent on the square root of the scan rates, thus charge transfer in the film was controlled by diffusion. The diffusion coefficient is figured out to be 2×10^_-10 cm²·s^-1. The …

Preparation,Structure And Properties Of Electrochromic Rhodium Oxide Films, Hai-Hong Wang, Tao Wang, Man-Ming Yan, Zhi-Yu Jiang

Journal of Electrochemistry

Electrochromic rhodium oxide films were prepared on ITO substrate by sol-gel method. The films exhibited reversible two-color (bright yellow at reduction and dark green at oxidation) electrochromic behavior in alkaline solution with good cycle stability. In-situ XRD, TGA-DTA, IR, XPS methods were used for studying the structure and chemical process of the films. The diffusion coefficient during the electrochromic process was measured by electrochemical impedance spectra method. It was found that the rhodium oxide films may be suitable for the use in electrochromic devices.

Syntheses And Photoluminescence Of Zinc Oxide Polyaniline Coaxial Nanowires And Their Array, Zhi-Xin Zheng, Yan-Yan Xi, Ping Dong, Huai-Guo Huang, Jian-Zhang Zhou, Lin-Lin Wu, Zhong-Hua Lin

Journal of Electrochemistry

A novel nanomaterial, zinc oxide (ZnO) and polyaniline (PANI) coaxial nanowires and their array in the template, was synthesized using anodic aluminum oxide (AAO) membrane as template. The morphology of these coaxial nanowires was observed with transmission electron microscope (TEM). The experiments on photoluminescence (PL) of coaxial nanowires and their array in AAO membrane show that the visible emission band of ZnO shifts from 530 nm to 400 nm and the luminescence is enhanced for the coaxial nanowires array in AAO membrane,and the visible emission band shifts to a lower wavelergth (385 nm) for coatial nanowires in NaOH solution. Possible …

Electrochemical Properties Of Mixed Metal Oxide Coated Titanium Anodes In Seawater, Ting-Yong Wang, Li-Kun Xu, Guang-Zhang Chen

Journal of Electrochemistry

Mixed metal oxide coated titanium anodes prepared by thermal decomposition were characterized by scanning electron microscopy and electrochemical measurement, while the consumption rate of an anode was also measured in seawater. In order to examine the practical performances of mixed metal oxide-coated anodes, a simulating test on floating dock in seawater has also been carried out. The SEM results indicate that oxide layers exhibited a cracked-mud morphology which endows the anode with good electrocatalytic activity. The electrochemical measurements showed that mixed metal oxide-coated anodes exhibit excellent electrochemical activity and electrochemical stability in seawater. Owing to good corrosion resistance and low …

A Blend Conducting Membranes For Direct Methanol Fuel Cells, Lei Li, Jun Zhang, Hong Wu, Yu-Xin Wang

Journal of Electrochemistry

An attempt was made to modify membranes for direct methanol fuel cells by blending Nafion or polystyrene sulfonic acid (PSSA) with polyvinylidene fluoride (PVDF) from their solutions. The proton conductivity and methanol barrier property as a function of the membrane compositions are discussed. Compared with the Nafion 117 membrane, the PVDF-Nafion blend membranes with 25 wt% of Nafion showed a decrease in the conductivity by about 2 orders of magnitude, and the methanol barrier properties increased about 3 orders of magnitude. If the ratio (σ/P) is adopted to characterize the performance of the membrane, the PVDF-PSSA and PVDF-Nafiion blend membranes …

Preliminary Study On Direct Ethanol Fuel Cell, Shu-Qin Song, Li-Kang Chen, Jian-Guo Liu, Zhao-Bin Wei, Qin Xin

Journal of Electrochemistry

The performance of a direct ethanol fuel cell based on Nafion115 was reported.PtRu/C and Pt/C were used as ethanol anode and oxygen cathode catalysts in a single cell of size 9 cm² .The effects of temperature, oxygen pressure, the flow rate of ethanol, and oxygen, and ethanol concentration were tentatively studied. The experimental results showed that the cell open circuit voltage 0.608 V, the cell voltage 0.329 V at 50 mA/cm², and the peak power density 19.25 mW/cm² were reached under the conditions of T_cell =85 ℃, P_O2 =0.5 MPa, C_ethanol =1.0 mol/L …

Electrosynthesis Of Glyoxylic Acid In A Packed Bed Reactor, Jin-Hong Fan, Jun Li, Yu-Zhong Su, Hao-Qi Gao

Journal of Electrochemistry

Glyoxylic acid was produced by electroreduction of oxalic acid in a packed bed reator. The cathodic and anodic electrolytes were super-saturated oxalic and hydrochloric acid aqueous solutions separated by a super-acid ion-exchange membrane. The current efficiency and yield of glyoxylic acid were studied under different structured packed bed reactors and different electrode materials, temperatures and current densities. The results indicated that the current efficiency of synthsis of glyoxylic acid was over 66.2% and the concentration of glyoxylic acid could reach 2.02% after 45min electrolysis with cathode of lead particles and anode of graphite board under conditions of temperature 32 ℃, …

Varying Current Electro-Synthesis Of Glyoxalic Acid In Pairs In The Fixed-Bed Electrolytic Cell, Yin-Sheng Chen, Xin-Sheng Zhang, Ying-Chun Dai, Wei-Kang Yuan

Journal of Electrochemistry

As for the process of the electro oxidation of glyoxal to glyoxalic acid, the electrolytic result of either fixed bed electrolytic cell or varying current electrolysis was better than that of either flat plate electrolytic cell or constant current electrolysis. The average current density of varying current electro synthesis of glyoxalic acid in pairs was 1535 A/m² and the current efficiency were 85.3% and 86.7% and the selectivity were 93.9% and 94.0% for the anodic oxidation and cathodal reduction respectively. The initial composition of anodic electrolyte was 7% glyoxal and 8% hydrochloric acid (W/W) and the cathodal electrolyte consisted …