Open Access. Powered by Scholars. Published by Universities.®

Materials Science and Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Catalysis and Reaction Engineering

Institution
Keyword
Publication Year
Publication
Publication Type

Articles 661 - 690 of 829

Full-Text Articles in Materials Science and Engineering

Research On Phenol Wastewater Treatment By Electrochemical Oxidation, Tian-Cheng Li, Shen-Lin Zhu Feb 2005

Research On Phenol Wastewater Treatment By Electrochemical Oxidation, Tian-Cheng Li, Shen-Lin Zhu

Journal of Electrochemistry

Electrochemical oxidation is an effective technology for the phenol wastewater treatment, and the anode properties are important to the electrochemical oxidationefficiency. The over-potentials of oxygen evolution have been measured for thestainless steel, feasible graphite and SnO2/Ti anode respectively. Moreover, the synthetic phenol wastewater was treated by the electrochemical oxidation with the stainless steel or feasible graphite anodes. The experimental results showed that the order of the over-potential is SnO2/Ti > graphite > stainless steel; meanwhile, the COD values of purified water were approaching to or less than 100 mg·L-1, and the phenol concentrations in the purified …

Go to article

Electrochemical Behaviours Of Hemoglobin-Ddab-Modified Powder Microelectrode And The Application Of The Powder Microelectrode In Determination Of Nitric Oxide, Zhi-Mou Guo, Huan Liu, Jian Chen, Wen-Ting Zhang Nov 2004

Electrochemical Behaviours Of Hemoglobin-Ddab-Modified Powder Microelectrode And The Application Of The Powder Microelectrode In Determination Of Nitric Oxide, Zhi-Mou Guo, Huan Liu, Jian Chen, Wen-Ting Zhang

Journal of Electrochemistry

The electrochemical behaviours of DDAB-Hb-PME were studied in this paper. The (apparent) surface concentration of Hb was enhanced greatly by using the powder microelectrode (technique). NO reacts with Hb and absorbs on the surface of the modified carbon powder. Therefore, the output of the electrode was enhanced greatly by employing PME with higher reaction surface (area). The sensitivity of DDAB-Hb-PME is 3.1 mA/μmol·L-1·cm2, which is much larger than the values obtained with the traditional electrodes. The detection limit is 9 nmol·L-1 and the linear response range is 9～100 nmol·L-1.

Go to article

Effect Of Fe3+ Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang Nov 2004

Effect Of Fe3+ Dopen Of Titanium Dioxide Film On Absorption Spectra And Photo Catalysis, Mei-Qun Xiao, Jia-Nian Shen, Moucheng Li, Peng-Fei Wu, Dong Liu, Yu-Juan Zhang

Journal of Electrochemistry

Photo-catalytic titanium dioxide film in nano crystalline has been prepared by electrochemical oxidation process and adding different amount of ferric ion into the electrolyte during the anodic oxidation.The effects of Fe3+ dopen on absorption spectra and photo-catalytic of the titanium dioxide films have been studied. It shows that the Fe3+ dopen caused the red shife of the absorption edge for the incoming light and exhibited the improved photocatalytic reactivity.

Go to article

Preparation And Photo-Catalyst Properties Of The α-Fe2O3-Tio2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen Nov 2004

Preparation And Photo-Catalyst Properties Of The α-Fe2O3-Tio2 Films On Sodium Alginate Polymer, Li-Qin Chen, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen

Journal of Electrochemistry

Three new nano thin films of α-Fe2O3, TiO2 and α-Fe2O3-TiO2 by doping their powder with sodium alginate polymer were prepared. Surface structure and catalytic activities of the films were characterized by FTIR, XRD, PL, TEM and I-V techniques. The results of UV-visible absorption showed that the methylene blue was mineralized in aqueous of α-Fe2O3/SA, TiO2/SA and (α-(Fe2O3))-TiO2 /SA upon radiation with ultra violet light. α-Fe2O3 enhanced their photo-decolorized-activities by doping 15% TiO2.

Go to article

Electrocatalytic Performances Of Carbon Nanotube Air Electrode For Oxygen Reduction, Feng-Ming Zhao, Chun-An Ma Nov 2004

Electrocatalytic Performances Of Carbon Nanotube Air Electrode For Oxygen Reduction, Feng-Ming Zhao, Chun-An Ma

Journal of Electrochemistry

The air electrodes with different mass ratio of Pt/active carbon or carbon nanotube as catalyst layer material have been prepared. The electrocatalytic performances for oxygen reduction were evaluated by means of polarization curve and electrochemical impedance spectroscopy (EIS). The results disclosed that carbon nanotubes dealt with nitric acid in the catalyst layer had been improved obviously on the electrocatalytic activity. After the surface of carbon nanotube was oxygenated and aggraded with platinum, the catalyst had obviously effects on the electrocatalytic activity. The air electrode with the mass ratio of active carbon to Pt/carbon nanotube in 4∶1 showed better electrocatalytic activity, …

Go to article

Fabrication Of Solid Oxide Fuel Cells And Analysis Of Their Structure And Performance, Nai-Tao Yang, Bo Meng, Ru-Jun Yu, Xiao-Yao Tan Aug 2004

Fabrication Of Solid Oxide Fuel Cells And Analysis Of Their Structure And Performance, Nai-Tao Yang, Bo Meng, Ru-Jun Yu, Xiao-Yao Tan

Journal of Electrochemistry

An intermediate temperature solid oxide fuel cell (IT-SOFC) was fabricated by co-copressing-sintering methods, and the electrolyte of Ce0.8Gd0.2O1.9 (CGO) and cathode materials of La0.6Sr0.4Co0.2Fe0.8O3-α (LSCF) were prepared by sol-gel method. The effect of preparation methods on the microstructure of the prepared fuel cells was analyzed by SEM . It shows that the cells prepared by the co-pressing/co-sintering method possess a dense electrolyte layer and a compact interface between electrolyte and anode but a curved configuration, while those prepared by the colloidal technique have a flat configuration …

Go to article

Synthesis Of (S)-3-Phenylpropane-2-Tert-Butoxycarbonylamino-1-Thiol And Its Electrochemical Behavior Self-Assembled On Gold, Ru Sun, Jian-Feng Ge, Mei Wang, Ren-Ao Gu Aug 2004

Synthesis Of (S)-3-Phenylpropane-2-Tert-Butoxycarbonylamino-1-Thiol And Its Electrochemical Behavior Self-Assembled On Gold, Ru Sun, Jian-Feng Ge, Mei Wang, Ren-Ao Gu

Journal of Electrochemistry

The synthesis of (S)-3-Phenylpropane-2-tert-butoxycarbonylamino-1-thiol(N-Boc-APT) from L-phenylalanine was reported. L-Phenylalanine was reduced to the corresponding amino alcohol, protection of the amino group using tert-butyl pyrocarbonate gave (S)-2-tert-butoxycarbonylamino-3-phenylpropane-1-ol, which was then O-mesylated and treated with potassium thioacetate in DMF to give 3-phenylpropane-2-tert- butoxycarbonylamino-1-etylmercapto. After the acetyl group was removed with ammonia in alcohol, the desired target molecular was obtained. The structure of intermediate and target molecular was conformed by IR and 1HNMR. We made N-Boc-APT self-assemble-modificated gold electrode and investigated its electrochemical behavior. The CV results of methylene blue on nano-Au/N-Boc-APT SAM/Au electrode showed that nano-Au could speed this electron transfer …

Go to article

Synthesis And Electrochemical Behavior Of Layered-Structure Limn1-XCrXO2, Jie Xiao, Hui Zhan, Yun-Hong Zhou Aug 2004

Synthesis And Electrochemical Behavior Of Layered-Structure Limn1-XCrXO2, Jie Xiao, Hui Zhan, Yun-Hong Zhou

Journal of Electrochemistry

The Layered-structure LiMn1-xCrxO2(x=0, 0.15) solid solution has been prepared by the rheological phase method. From the XRD results, undoped LiMnO2 crystallized almost entirely in the orthorhombic phase while the structure of LiMn0.85Cr0.15O2 belongs to monoclinic phase. TEM investigation shows that the final powder product consists of ultrafine spherical particles which are distributed homogeneously, with the average diameter ranging from 60 to 300nm. The initial discharge capacity of LiMn0.85Cr0.15O is much higher than that of undoped LiMnO2. After 40 cycles, the capacity retention …

Go to article

Electrochemical Reduction Of Nitrobenzene On The Wc Electrode In Acidic Solution, Chun-An Ma, You-Qun Chu, Ying-Hong Zhu, Zhi-Hua Xu Aug 2004

Electrochemical Reduction Of Nitrobenzene On The Wc Electrode In Acidic Solution, Chun-An Ma, You-Qun Chu, Ying-Hong Zhu, Zhi-Hua Xu

Journal of Electrochemistry

The tungsten carbide (WC) electrode was constructed by using polyterafluoroethylene as binder. The electrochemical behavior of nitrobenzene on the WC electrode in acidic solution was investigated by cyclic voltammetry, linear scan method and chronoamperometry. Experimental results showed that WC electrode had good activity for the electrochemical reduction of nitrobenzene, and the electrode process was controlled by diffusion and electrochemical stepssimultaneously. The apparent active energy of the electrode process is 23.7kJ⋅mol-1, while the active energy of the electrochemicalstep is 10.91kJ⋅mol-1.

Go to article

Solid State Synthesis And Electrocatalysis Of Pt/Moo3 For The Oxidation Of Methanol, Qing Wang, Yi-Ming Zhou, Yang Shao, Yi-Gang Ji, Juan Xu, Ya-Wen Tang, Tian-Hong Lu, Tao Shen Aug 2004

Solid State Synthesis And Electrocatalysis Of Pt/Moo3 For The Oxidation Of Methanol, Qing Wang, Yi-Ming Zhou, Yang Shao, Yi-Gang Ji, Juan Xu, Ya-Wen Tang, Tian-Hong Lu, Tao Shen

Journal of Electrochemistry

The electrocatalyst, Pt/MoO3 synthesized by solid state reaction, was used for the oxidation of methanol in direct methanol fuel cells. The X-Ray diffraction and cyclic voltammetry were employed to investigate the performance of the material. It was shown that the typical diffraction peaks for Pt appeared in XRD. And a good electrocatalysis for methanol oxidation was observed. The peak potential of the methanol oxidation appeared at ca. 0.63V(vs.SCE) and the peak current density for the oxidation was 78.1 mA⋅cm-2.

Go to article

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin Aug 2004

Lithium Insertion Into Tio2(B) Nanobelts Synthesized By The "Soft Chemical" Method, Cha-Geng Nie, Zheng-Liang Gong, Lan Sun, Juan Zuo, Yue-Kun Lai, Chang-Jian Lin

Journal of Electrochemistry

TiO2(B) Nanobelts were synthesized by using the "Soft chemical"method. The products were characterized by means of transmission electron microscope(TEM), X-ray diffraction(XRD), Raman spectrum and energy dispersive spectrum(EDS). Galvanostatic charging and discharging tests showed that lithium-ion intercalation/deintercalation occurred reversibly in the TiO2(B) nanobelts electrode, and a high capacity (265 mAh·g-1) can be obtained. The results suggested that TiO2(B) Nanobelts might be a promising negative electrode material of second Lithium battery.

Go to article

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren, Zhen-Xing Liang, Xin-Sheng Zhao, Qin Xing, Gong-Quan Sun, Xue-Feng Yang Aug 2004

Preliminary Study Of Speek Membranes For Direct Methanol Fuel Cells Application, Su-Zhen Ren, Zhen-Xing Liang, Xin-Sheng Zhao, Qin Xing, Gong-Quan Sun, Xue-Feng Yang

Journal of Electrochemistry

This paper describes the methanol permeability characterization of SPEEK membranes and their feasibility for DMFC application. The SPEEK membranes showed a significant lower methanol permeation than Nafion 115 determined from voltammetric methods. An increase in open circuit voltage was found in the performance of SPEEK membranes in DMFC. The power density of the cell using SPEEK membrane was considerably poorer than that of Nafion 115. If modified properly, the SPEEK membranes can be chosen for DMFC application based on this study.

Go to article

Study On An Intermediate Temperature Planar Solid Oxide Fuel Cell, Shao-Rong Wang, Wen-Xia Chen, Ting-Lian Wen, Jia-Di Cao, Zhi-Yi Lv, Da-Qian Wang Aug 2004

Study On An Intermediate Temperature Planar Solid Oxide Fuel Cell, Shao-Rong Wang, Wen-Xia Chen, Ting-Lian Wen, Jia-Di Cao, Zhi-Yi Lv, Da-Qian Wang

Journal of Electrochemistry

Tape cast method was applied to prepare green sheets of Ni/YSZ anode supported YSZ thin film. After isostatic pressure treatment and cosintering, the YSZ film on the Ni/YSZ anode was gas-tight dense, and 15~30 μm thick. The area of the composite film was over 100 cm2. A Ce0.8Sm0.2O1.9 (CSO) interlayer was sintered on to the YSZ electrolyte film to protect La0.6Sr0.4CoO3 (LSCO) cathode from reaction with YSZ at high temperatures. The LSCO cathode layer was screen printed onto the CSO interlayer and sintered at 1200 ℃ for 3 …

Go to article

Electrocatalytic And Lifetime Studies Of Commercial Catalystsin A Pemfc, Cheng Xuan, Yan-Yun Ma, Li Qi, Cheng Peng, Ling Chen, Jun Zhao, Ying Zhang, Qin-Bai Fan May 2004

Electrocatalytic And Lifetime Studies Of Commercial Catalystsin A Pemfc, Cheng Xuan, Yan-Yun Ma, Li Qi, Cheng Peng, Ling Chen, Jun Zhao, Ying Zhang, Qin-Bai Fan

Journal of Electrochemistry

A particularly designed H-type cell was used to simulate the operating condition of a hydrogen-air proton exchange membrane fuel cell (PEMFC). The electrocatalytic activity, morphology, structure and lifetime of commercially available catalysts, carbon support platinum (Pt/C) and unsupported platinum-ruthenium (Pt-Ru), were preliminary studied by carrying out electrochemical measurements and by SEM, XRD techniques. The catalysts were simultaneously tested in the H-cell under operation, and also separately tested in a conventional electrochemical cell for comparison. It was found that the characteristic peaks of hydrogen adsorption/desorption on cyclic voltammograms shifted considerably to a more positive direction for Pt/C, while a more negative …

Go to article

Investigation Of Adsorption And Oxidation Behavior Of Isosafrole On A Smooth Pt, Xiao-Hong Zhang, Xiao-Jing Su, Qi-Ling Zhong, Lei Zhang, De-Sheng Mei, Bin Ren, Zhong-Qun Tian May 2004

Investigation Of Adsorption And Oxidation Behavior Of Isosafrole On A Smooth Pt, Xiao-Hong Zhang, Xiao-Jing Su, Qi-Ling Zhong, Lei Zhang, De-Sheng Mei, Bin Ren, Zhong-Qun Tian

Journal of Electrochemistry

The electro-oxidation of isosafrole on a smooth platinum electrode was investigated in the non-aqueous solution. The CV curve shows two oxidation peaks and one reduction peak in the potential region between -0.5 V and 1.95 V. The relation between the oxidation and reduction peaks has been determined also by CV. The adsorption behavior of isosafrole on Pt was also investigated.

Go to article

Study On Reduction Process Of Electrolyic Manganese Dioxide In Situ By Ultraviolet-Visible Absorption Spectroscopy, Li-Cai Zhu, Zhong-Zhi Yuan, Wei-Shan Li May 2004

Study On Reduction Process Of Electrolyic Manganese Dioxide In Situ By Ultraviolet-Visible Absorption Spectroscopy, Li-Cai Zhu, Zhong-Zhi Yuan, Wei-Shan Li

Journal of Electrochemistry

The concentrationsof soluble Mn(Ⅲ) species, during the reduction ofelectrolytic MnO2 (EMD) in alkaline solution,have been monitored in situ by UV-visible spectroscopy. The concentration of Mn(Ⅲ) ion in solution changes with discharge time. The first electron discharge process of EMD can be described by three different steps: 1) the reduction of Mn4+ ions on the surface of EMD particles and the structural defect regions within the EMD, 2) the reduction of Mn4+ ions in ramsdellite, 3)the reduction of Mn4+ ions in pyrolusite. During the second electron discharge of EMD, the soluble Mn(Ⅲ) is reduced to Mn(Ⅱ) , …

Go to article

Template Synthesis Of Highly Ordered Monocrystalline Metal Nanowire Arrays By A Two-Step Ac Electrodeposition, Juan Xiang, Jing-Hua Tian, Zi-Mian Ni, Zhi-Feng Huang, Bo Liu, Zhong-Qun Tian Feb 2004

Template Synthesis Of Highly Ordered Monocrystalline Metal Nanowire Arrays By A Two-Step Ac Electrodeposition, Juan Xiang, Jing-Hua Tian, Zi-Mian Ni, Zhi-Feng Huang, Bo Liu, Zhong-Qun Tian

Journal of Electrochemistry

The monocrystalline metal nanowire arrays were prepared by using a two-step AC electrodeposition in porous anodic aluminum oxide (AAO) template. The growth mechanism of nanowires was discussed. As a result, it has been found that the second voltage pulse has a considerable effect on the pore-filling ratio, the uniformity and the crystal structure, whereas the initial voltage pulse affects only the pore-filling ratio. Using the two-step AC electrodeposition, a highly ordered monocrystalline metal nanowire arrays with a pore-filling ration above 95% can be easily obtained.

Go to article

Studies On The Mechanism Of Electroreduction Of Oxalic Acid, Yu-Zhan Li, Xin Liu, Rui-Sheng Hu, Deng-Ping Gu Feb 2004

Studies On The Mechanism Of Electroreduction Of Oxalic Acid, Yu-Zhan Li, Xin Liu, Rui-Sheng Hu, Deng-Ping Gu

Journal of Electrochemistry

The electroreduction mechanism of oxalic acid on Pb electrode in Na2SO4 solution were investigated using high scan rate cyclic voltammetry and chronoamperometry. The dynamic parameters for the first step electron transter reaction of oxalic acid electroreduction by were determined. The corresponding reduction peak potentials of oxalic acid, glyoxylic acid and glycolic acid in the cyclic voltammogranis obtained in the same condition were compared, and the intermediate reduction products of oxalic acid were suggested. The results showed that oxalic acid is weakly absorbed on the lead electrode.

Go to article

Preparation, Structure And Electrochemical Hydrogenation Of Carbon Nanotubes Supported Platinum Catalysts, Qing-Gang He, Xiao-Zi Yuan, Xian-Xia Yuan, Zi-Feng Ma Feb 2004

Preparation, Structure And Electrochemical Hydrogenation Of Carbon Nanotubes Supported Platinum Catalysts, Qing-Gang He, Xiao-Zi Yuan, Xian-Xia Yuan, Zi-Feng Ma

Journal of Electrochemistry

In this paper, Pt/CNTs catalyst was prepared and its electrocatalytic property was studied by obtaining cycling voltammetry curves (C-V) and Tafel curves. In addition, the XRD,XPS and TEM tests were carried out to determine the structure and composition of the catalysts. It can be found that the platinum loading has been increased significantly using a carbon nanotubes support. Dispersion of Platinum was better and gave more active sites. The electrochemical characteristic of Pt/CNTs was also more desirable than that of Pt/C catalys t(Johnson Matthey). In conclusion, carbon nanotubes can played a conspicuous role in "electrogenerative" processes of PEMFC hydrogenation reactor.

Go to article

Electrochemical Synthesis Of Ferrate(Vi) By Anodic Oxidation, Jia-Ju Xu, Jian-Ming Wang, Wei-Hua Yang, Cheng Chen, Jian-Qing Zhang Feb 2004

Electrochemical Synthesis Of Ferrate(Vi) By Anodic Oxidation, Jia-Ju Xu, Jian-Ming Wang, Wei-Hua Yang, Cheng Chen, Jian-Qing Zhang

Journal of Electrochemistry

The ferrate(Ⅵ) was synthesized by electrochemical anodic oxidation. The effects of preparation conditions on the current yield of ferrate(VI) synthesis have been studied in this work. The experimental results showed that grey cast iron as an anodic material is suitable for electrochemical synthesis and NaOH solution as an electrolyte results in a higher current yield than KOH solution. The highest current yield was obtained at a current density (4.54) mA·cm-2, temperature 20 ℃ and 14 mol·dm-3 NaOH. In this case, a current yield of 68.5% was obtained by electrolysis for 1 h.

Go to article

Progress In Research For Biofuel Cell, Yue Bao, Xia-Qin Wu Feb 2004

Progress In Research For Biofuel Cell, Yue Bao, Xia-Qin Wu

Journal of Electrochemistry

In this article, research progresses of the biofuel cell in recent years were summarized. The operation principle and classification of the biofuel cells were described. The role of the mediator for promoting electron transfer in biofuel cells and the techniques for improving the electric properties of biofuel cells, such as output potential, were discussed with some attracting research instances. Finally, the choke points for research of biofuel cell were explored, and the application prospect of biofuel cells was forecasted.

Go to article

Preparation And Characterization Of Y-Type Carbon Nanotubes By Using Anodized Alumina Oxide (Aao) Template, Jing Zhang, Quan-Yong Gao, Yong Yang Nov 2003

Preparation And Characterization Of Y-Type Carbon Nanotubes By Using Anodized Alumina Oxide (Aao) Template, Jing Zhang, Quan-Yong Gao, Yong Yang

Journal of Electrochemistry

In this work, potential-modulation method was used in two-step anodization process to make an AAO template with Y-type nanochannels. Then Y-type carbon nanotubes with controlled length and branch angle were prepared in the template based on chemical vapor decomposion (CVD) method with Co particles as catalyst and C2H2 as carbon source. The Y-type nanotube branches exhibit the angle distribution ranging from 20° to 120°. The results demonstrated that the oxidation potential should be responsible for the angles and length of the branches. Short pulse and high oxidation potential will result in the short and dense nanotube branches.

Go to article

Application Of Hydrogen-Storage Alloy Electrode In Electrochemical Reduction Of Glucose, Hui Chen, You-Gen Tang, Zheng Tang Nov 2003

Application Of Hydrogen-Storage Alloy Electrode In Electrochemical Reduction Of Glucose, Hui Chen, You-Gen Tang, Zheng Tang

Journal of Electrochemistry

Electrolysis of glucose was performed at constant potential using hydrogen-storage alloy as catalytic reduction electrode. It was found that the superficial treatment and activation of hydrogen-storage alloy powder had obvious effects on improving the current efficiency of sorbitol. Under the optimums, current efficiency of sorbitol by electrolyzing glucose was over 94%. The yield of sorbitol was over 80%, the lifespan of electrode was tested and analyzed, the ways of regeneration were discussed.

Go to article

Optimizing Catalyst Layer Composition Of Pemfc By Orthogonal Method, Ming-Hua Wang, Xin-Jian Zhu, Guang-Yi Cao, Sheng Sui, Qing-Chun Yu, Ming-Ruo Hu, Zheng-Yu Fan Nov 2003

Optimizing Catalyst Layer Composition Of Pemfc By Orthogonal Method, Ming-Hua Wang, Xin-Jian Zhu, Guang-Yi Cao, Sheng Sui, Qing-Chun Yu, Ming-Ruo Hu, Zheng-Yu Fan

Journal of Electrochemistry

The optimal composition of catalyst layer in a PEMFC electrode was studied through orthogonal method. It was showed that the performance of hydrophilic electrodes, in which there is no PTFE in the catalyst layer, were more favorable than that of hydrophobic electrodes. According to this condition, the power density of PEMFC attained 0.37 w·cm-2 when the Nafion loading was 1.4 mg·cm-2, and the Pt loading was 0.4 mg·cm-2 in the catalyst layer, using H2 as fuel and air as oxidant both at atmospheric pressure. Additionally, the results showed that increasing Pt loading in Pt/C catalyst …

Go to article

The Study On Carbon Nanotube-Loaded Pt Catalysts For Proton Exchange Membrane Fuel Cells, Hong Zhu, Feng-Juan Ge, Xiao-Hong Kang, Yu-Guo Yang, Yun-Hua Xu Nov 2003

The Study On Carbon Nanotube-Loaded Pt Catalysts For Proton Exchange Membrane Fuel Cells, Hong Zhu, Feng-Juan Ge, Xiao-Hong Kang, Yu-Guo Yang, Yun-Hua Xu

Journal of Electrochemistry

Carbon nanotube-supported-platinum (Pt/CNTs) and carbon-supported-platinum (Pt/C) catalysts were synthesized by in-situ chemical reduction. They were analyzed using TEM and XRD, then made into electrodes to be part of assemable PEMFC for the performence tests. The resulted show that Pt clusters in both catalysts are of small particle size (about 4nm), and Pt/CNTs exhibits a higher catalytic activity than Pt/C.

Go to article

Study On Degradation Of Phenol By Electrochemical Oxidation, Yue-Li Liu, Hong-Hua Ge Nov 2003

Study On Degradation Of Phenol By Electrochemical Oxidation, Yue-Li Liu, Hong-Hua Ge

Journal of Electrochemistry

Electrochemical oxidation of phenol was carried out by the Dimensionally Stable Anodes (DSA) electrode, which has been discarded as waste by alkali chloride factory. The result indicates that a good phenol removal can be obtained under certain phenol concentration by the DSA electrode. The key factor in effecting phenol removal of electrochemical oxidation is applied current density, the following factors are pH, electrolyte concentration and phenol concentration. After experiments, the optimal test conditions are 30 mA/cm2, pH 10, electrolyte concentration 10 mg/L, phenol concentration 10 mg/L.67% CODcr removal and 90% absorbance removal are gained by electrochemical oxidation for …

Go to article

Adsorption And Oxidation Of Phenol Electrode Processes, Bao-Cheng Wang, Yan-Ping Sun, Jin-Hua Zhu Nov 2003

Adsorption And Oxidation Of Phenol Electrode Processes, Bao-Cheng Wang, Yan-Ping Sun, Jin-Hua Zhu

Journal of Electrochemistry

The electrochemical behaviors of platinum electrode were studied by cyclic voltammetry in 1mol/L sulfuric acid solution and 1mol/L sulfuric acid solution contained phenol. The adsorption characteristics of phenol and the intermediat on electrode surface have been discussed. The reactive reversibility and oxidation mechanism of phenol on electrode process have been investigated.The potential of characteristic adsorption was suggested. The various products woud be formed when the electrode potential was greater than the one of characteristic adsorption.

Go to article

Synthesis And Electrochemical Properties Of K2Feo4, Ning Zhou, Shi-Hai Ye, Yong-Long Wang, Xue-Ping Gao, Dong-Feng Lin, Zuo-Xiang Zhou, De-Ying Song Aug 2003

Synthesis And Electrochemical Properties Of K2Feo4, Ning Zhou, Shi-Hai Ye, Yong-Long Wang, Xue-Ping Gao, Dong-Feng Lin, Zuo-Xiang Zhou, De-Ying Song

Journal of Electrochemistry

The K2FeO4 used for new positive electrode materials was prepared. The primary batteries were used in different concentration of electrolyte and different currents. In 9 mol/L KOH , the capacity was the best. The higher the concentration of electrolyte, the lower the electric potential was. When the batteries discharged in 0.4 C , the capacity reached 521.3 mAh/g. By XRD, we gave the reasonable explanations for the discharge products of K2FeO4. Possible mechanism of discharge is discussed.

Go to article

Synthesis Of Polyunit Vapor Phase Inhibitor And Its Volatile Corrosion Inhibition Performance, Da-Quan Zhang, Li-Xin Gao, Guo-Ding Zhou Aug 2003

Synthesis Of Polyunit Vapor Phase Inhibitor And Its Volatile Corrosion Inhibition Performance, Da-Quan Zhang, Li-Xin Gao, Guo-Ding Zhou

Journal of Electrochemistry

A Mannich Base derivative (BMMCH), containing two morpholinum moieties and one cyclohexylamnonium moiety, was synthesized through aminomethy1 reaction. Its configuration was verified by IR and 1H-NMR. Its volatile rustproofing effect was appraised by volatile rustproofing sieve test and vapor inhabitability test. The result shows that BMMCH has good protection effect for carbon steel. BMMCH has lower volatility compared with dicyclohexylamnonium nitrite (DICHAN) via closed space volatile weight-loss test. The inhibition mechanism was studied by potentiodynamic polarization electrochemistry technique in ASTM simulated atmospheric water. The corrosion potential of carbon steel electrode shifted to a negative direction when BMMCH was joined …

Go to article

Comparison Of Thermal Cyclic Oxidation Of The Pvd Ni-Al And Hvof-Mcraly Coatings, J-T Chang, C-H Yeh, J-L He, K-C Chen Aug 2003

Comparison Of Thermal Cyclic Oxidation Of The Pvd Ni-Al And Hvof-Mcraly Coatings, J-T Chang, C-H Yeh, J-L He, K-C Chen

Journal of Electrochemistry

A PVD process-cathodic arc plasma ion plating was used to deposit Ni-Al films on Inconel 600 superalloy. The oxidation behaviors of PVD Ni-Al coating and the thermal sprayed CoCrAlY coatings were revealed and compared by performing cyclic thermal oxidation test at 1100 ℃ to evaluate its feasibility. Experimental results showed that the films with different compositions of Ni62Al38, Ni63Al37 and Ni69Al31 could be obtained when using Ni52Al48, Ni60Al40 and Ni70Al30 as targets, respectively. During the cyclic thermal oxidation test, the …

Go to article

First Prev Next Last