Mechanics of Materials Commons^™

Ballistic Projectile Metallurgical Issues And Fundamentals: Aerosol Production In Rod Penetration Erosion And Erosion Phenomena Associated With Railgun Development, Brenda Ivette Machado

Open Access Theses & Dissertations

The issue is derived from ballistic erosion as it relates to nanoparticle production and respiration of these particles as a health concern ballistic erosion and ballistic erosion as it relates to railgun performance. A common thread between these two issues is dynamic recrystallization (DRX). DRX has been demonstrated to be the dominant mechanism for solid-state flow associated with ballistic projectile/target penetration and interaction, friction-stir welding phenomena, and other high-strain rate deformation phenomena.

Aerosol particulates collected on filters from ballistic penetration and erosion events for W-Ni-Co and W-Ni-Fe kinetic energy rod projectiles penetrating steel target plates were observed to be highly …

Microstructural Architecture Developed In The Fabrication Of Solid And Open-Cellular Copper Components By Additive Manufacturing Using Electron Beam Melting, Diana Alejandra Ramirez

Open Access Theses & Dissertations

The fabrication of Cu components were first built by additive manufacturing using electron beam melting (EBM) from low-purity, atomized Cu powder containing a high density of Cu2O precipitates leading to a novel example of precipitate-dislocation architecture. These microstructures exhibit cell-like arrays (1-3µm) in the horizontal reference plane perpendicular to the build direction with columnar-like arrays extending from ~12 to >60 µm in length and corresponding spatial dimensions of 1-3 µm. These observations were observed by the use of optical metallography, and scanning and transmission electron microscopy. The hardness measurements were taken both on the atomized powder and the Cu components. …

Effect Of Process Parameter On Temperature Distribution, Microstructure, And Mechanical Properties Of Self-Reacting Friction Stir Welded Aluminum Alloy 6061-T651, Monica Adriana Torres

Open Access Theses & Dissertations

Self-reacting friction stir welding is the latest FSW tool configuration developed, it employs two shoulders--one on top and one on the bottom of the workpiece-- this tool configuration offers many advantages over conventional welding techniques. However, the current lack of information and specifications limits its understanding and application. This investigation analyzed the effect of process parameters on temperature distribution, microstructure evolution, and final mechanical properties of 6061-T651 SR-FS welds. A factorial experiment was carried out, in which three-process parameters were analyzed--rotational speed, travel speed, and tool plunge force-- three levels were analyzed for each parameter, except for a tool plunge …

Fabrication And Characterization Of Nanocrystalline Yttrium Oxide Thin Films For Electronic Device Applications, Mudavakkat Vikas Haridas

Open Access Theses & Dissertations

This thesis presents the optimization of growth conditions for fabricating nanocrystalline Yttrium Oxide (Y2O3) thin films on silicon and optical grade, high quality quartz substrates in order to study its structural, optical and electrical properties for electronic device applications.

Commercially Y2O3 has proven to be difficult to fabricate at high quality due to its high temperature growth requirements and the need to alter established fabrication methods for electronic devices. A high temperature requirement for high quality poses a problem for research and analysis. This calls upon for an optimization of the growth conditions to facilitate fabrication of thin films for …

The Effect Of Cr, Si And B On The Oxidation Behavior On Three Nb-Based Alloys, David Alvarez

Open Access Theses & Dissertations

Nb-based alloys are of particular interest to replace the current Ni-based superalloys for high-temperature structural applications. One important limitation to improve the efficiency of gas-turbine engines is the temperature limit of current materials being used. By allowing the temperature to increase, the efficiency will increase. Nb-based alloys have high melting points and adequate mechanical properties but the oxidation resistance is still inadequate.

This research focuses on the oxidation behavior of three Nb-based alloys to study the effect of Cr and Si variation and look at the effect of Boron. Boron can form a glassy borosilicate which is viscous at high …

Development And Characterization Of The Oxidation Behavior Of Various High Temperature Niobium Based Alloys, Benedict Isabel Portillo

Open Access Theses & Dissertations

The oxidation response of various niobium based refractory alloys from the Nb-Mo-Si-B-X alloy system has been examined at temperatures between 700 and 1400°C in air. The development of these alloys was part of an ongoing effort to develop and discover a new materials system capable of replacing nickel based super alloys. Additions of titanium were found to provide limited oxidation resistance. A discontinuous layer of TiO2 was observed to from at temperatures above 1100°C. Alloys containing titanium additions were observed to suffer from pest oxidation at low and intermediate temperatures due to the development of Nb2O5. Poor oxidation resistance at …

An Ab-Initio Study Of The Elastic Properties Of Important Group Iv Diborides At High Temperatures, Manny Gonzales

Open Access Theses & Dissertations

Presented is an ab-initio Molecular Dynamics (MD) study, employing the Density Functional Theory (DFT), of the lattice parameter, thermal expansion coefficients and elastic constants of ZrB₂, TiB₂ and HfB₂ as a function of temperature. The MD trajectories provide the equilibrium lattice parameters at finite temperatures, and the gradient of the energy from these equilibrium solutions is then used to calculate the components of the stiffness tensor. The results for ZrB₂ are shown to agree well with reported experimental results for the lattice parameters and elastic constants as a function of temperature.

Sensitivity Analysis Of The Johnson-Cook Plasticity Model For Hypervelocity Impacts: A Hydro-Code Study, Carlos David Castellanos

Open Access Theses & Dissertations

Computer simulations have been in use for decades in the modeling of hypervelocity impacts and general large deformation problems. Several computer codes have been developed to simulate this type of problems under a variety of geometric configurations and for any number of materials. These codes make use of several constitutive material models to simulate the response of the material under a variety of thermo-mechanical conditions. The Johnson-Cook constitutive model is widely used in the simulation hypervelocity impacts for the simulation of crater formation and even perforation of target structures. This thesis presents the results of a sensitivity study of this …

Selection Process, Modified Impact Testing And Failure Analysis Of An Electron-Beam-Melted Ti-6al-4v 3d Tessellation Based On The Eulerian Path Of The First Stellation Of The Rhombic Dodecahedron Open Unit Cell, Hugo Lopez

Open Access Theses & Dissertations

Ti-6Al-4V lattice block structures manufactured through the electron beam melting (EBM) process are a promising field in design and research due to great advantages that the alloy, the process and the final product offer. Three lattice block structures were manufactured through the electron beam process using an ARCAM A2 machine. The structures were designed using the MATERIALIZE^TM software and were designed around different types of unit cells. Compression testing was performed and one unit cell was selected due to its anisotropic behavior for modified impact testing. The same unit cell was used and it was scaled up to add …

Processing Of Zrb2-Zrc-Zrxsiy Ceramic By Reactive Metal Penetration, Nischel B. Maheswaraiah

Open Access Theses & Dissertations

The processing of ZrB2-ZrC-ZrxSiy composite by reactive metal penetration was investigated as a successor to the ZrB2-SiC composites for hypersonic vehicles application, which cannot be used for extended time at temperatures greater than 1600C due to formation of SiO and CO gases. Zirconium (Zr), zirconium disilicide (ZrSi2), and boron carbide (B4C) were reacted in graphite crucibles for 60, 120, 180, and 240 minutes. Microscopy and x-ray diffraction (XRD) deduced the formation of a heterogeneous microstructure of ZrB2-ZrC-ZrxSiy precipitates surrounded by a solidified Zr-Si melt. Unreacted boron carbide was observed in samples held at 1860C for 60 minutes and 120 minutes, …

Microstructure Investigation Of Al-Rich Titanium Aluminum Alloys, David Pham

Open Access Theses & Dissertations

The microstructures of Ti-Al alloys with 70-80 wt% Al were investigated. Aluminum wire (99.999%) and TiH₂ powder (99.7%) were used to produce the sample compositions inside a vertical tube furnace at 1600^oC in an Ar atmosphere. Argon is purified through a dehumidification and deoxidation system. Magnesium perchlorate Mg(ClO₄)₂ acts as a desiccant and titanium sponge pulls oxygen from the Ar in furnaces operating at 800^oC and 750^oC. X-ray diffraction and an optical microscope are used to identify phases and compositions

Spectroscopic Study Of The Inhibition Of Calcium Oxalate Calculi By Larrea Tridentata, Luis Alonso Pinales

Open Access Theses & Dissertations

The causes of urolithiasis include such influences as diet, metabolic disorders, and genetic factors which have been documented as sources that aggravate urinary calculi depositions and aggregations, and, implicitly, as causes of urolithiasis. This study endeavors to detail the scientific mechanisms involved in calcium oxalate calculi formation, and, more importantly, their inhibition under growth conditions imposed by the traditional medicinal approach using the herbal extract, Larrea tridentata. The calculi were synthesized without and with Larrea tridentata infusion by employing the single diffusion gel technique. A visible decrease in calcium oxalate crystal growth with increasing amounts of Larrea tridentata herbal infusion …

The Reactivity Of A Zr-Si Melt With B4c At Ultrahigh Temperatures, Alvaro Vega Sandate

Open Access Theses & Dissertations

Surfaces with exceptional properties are needed for next generation materials. Hypersonic re-entry space vehicles or turbines are subjected to both oxidizing and neutral environments and nose-caps or wings on such vehicles could easily reach operating temperatures of over 2000°C. Ultrahigh temperature ceramics like ZrB2 and HfB2 have melting temperatures of 3245°C and 3380°C respectively. However, these materials need to be protected from oxidation, usually with an oxide layer. Zirconium is more affordable and will be used to study its reaction with B4C and ZrSi2.

Experimentation was conducted by melting Zr slugs into a B4C and ZrSi2 packed bed at 1860°C …

Resistive Switching Of Tin Dioxide (Sno2) For Memristor Applications, Sergio Fabian Almeida

Open Access Theses & Dissertations

In the last decades new electrical devices have been investigated in order to overcome problems caused by integrated circuit shrinking. Within these devices there is one that has attracted much attention due to its high scalability and simple structure. This device was proposed theoretically by Leon Chua in 1971 who gave it the name of "Memristor". In the recent years thin films structures composed of a metal/oxide/metal (MOM) stack have been linked to this new device, also known as "Resistive switching". There are several applications for the memristor; one of the most important is for resistive random access memory (ReRAM) …

Hybrid Manufacturing: Integrating Stereolithography And Direct Print Technologies, Amit Lopes

Open Access Theses & Dissertations

The focus of this research was the development of a hybrid manufacturing system that integrates stereolithography (SL) and direct print (DP) technologies to fabricate three dimensional (3D) structural electronic devices within a single set-up. The capabilities of this new additive manufacturing (AM) technology was explored in the context of fabricating and prototyping complex electronic devices in which conformal shape, rugged and light-weight integration, and a natural resistance to reverse engineering are all of paramount importance. Consequently, electronic components can be tightly integrated together in a rugged, light-weight 3D structure of arbitrary form. This research is a continuing advancement of the …

Experimental Study Of The Response Of Semiconductor Detectors For Edxrf Analysis., Sunil Kumar Valaparla

Open Access Theses & Dissertations

This present work relates to the study and characterization of the response function of an energy-dispersive x-ray spectrometer. The problems of energy, efficiency and resolution calibration of the system operating in the energy (5-60 keV) range are discussed. We present the operation characteristics of the portable pyro-electric x-ray generator (COOL-X) and the application of the calibrated response spectrum in the elemental analysis using X-ray Fluorescence (XRF).

We study the response of the Si(Li)-Pin XR-100CR semiconductor detector to low energy photons. The photopeak efficiency was determined experimentally by using radioisotopes and compared against a theoretical efficiency curve. The efficiency for gamma …

Characterization And Cytotoxic Assessment Of Ballistic Aerosolized Particulates For Tungsten Alloy Penetrators Interacting With Steel Targets, Brenda Ivette Machado

Open Access Theses & Dissertations

The aerosolized particulates produced during an impact of depleted uranium munitions can potentially contaminate extensive areas around the impact sites and cause a wide spectrum of civilian and military damage. Thus materials such as WHA have been prompted for consideration. The present research is concerned with the regular collection of aerosol particulates associated with ballistic WHA rod penetration into rolled homogeneous steel (RHA) or other related steel armor as armor plate sequences. Particulate size characterization via scanning electron microscopy (SEM) and transmission electron microscopy (TEM) along with chemical compositions via energy dispersive spectroscopy (EDS) were the focus of this research. …

Fabrication And Characterization Of Zirconium Oxide Thin Films, Vemnkata Rama Sesha Ravi Kumar Vemuri

Open Access Theses & Dissertations

Zirconium oxide (ZrO2) is an important material with a potential for a wide range of technological applications. The outstanding chemical stability, electrical and mechanical properties, high dielectric constant, and wide band gap of ZrO2 make it suitable for several industrial applications in the field of optics, electronics, magneto-electronics, and optoelectronics. ZrO2 is frequently used as a high refractive index material in multilayer optical coatings in high power laser systems. ZrO2 is employed in super plastic structural ceramics that demonstrate excellent strength and fracture toughness. ZrO2 has been considered as a promising dielectric to replace SiO2 in advanced metal oxide semiconductor …

Art In A New Light: Design And Assessment Of Illuminants To Reduce Photochemical Degradation Of Works Of Art, Monica Fabiola Delgado

Open Access Theses & Dissertations

The purpose of this research is to design the best lighting that will minimize long term photochemical degradation of Old Master Drawings and/or other works of art, while maintaining the patron's appreciation of the object's color and detail. The present approach is a technological refinement to the basic underlying earlier work on fluorescent lighting by W. A. Thornton, W.A. at General Electric1. Thin-film dielectric, multi-coating technology is used to create filters that eliminate ultraviolet light, near infrared light and significant unnecessary parts from the visible spectrum, thus maximizing the reduction in photochemical degradation, while maintaining optimal color rendering. Three interference …

Additive Layer Manufacturing Of Ti-6al-4v By Electron Beam Melting From Powder Particles: Solid, Mesh And Foam Components Study, Sara M. Gaytan

Open Access Theses & Dissertations

Additive Manufacturing by Electron Beam Melting Rapid Manufacturing is a technology that consists of the fabrication of a CAD design by melting powder particles in a layer by layer fashion. In this study, Ti-6Al-4V has been utilized to fabricate solid, mesh and foam components by EBM technologies. Powder analysis of Ti-6Al-4V was performed to obtain a better understanding of the porosity obtained by the system. After proper optimization of the machine, and porosity control, microstructural analysis was performed to the components already mentioned and correlated by transmission electron microscopy. Besides the microstructural analysis, tensile and hardness testing was performed to …

Assessing Repeatability Of Four-Point Bending Method For Estimating Fatigue Cracking Of Hot Mix Asphalt, Sara -. Montazeri

Open Access Theses & Dissertations

The objective of this thesis was to assess the repeatability of four-point bending method for estimating fatigue cracking of hot mix asphalt. This experimental research examined the influence of mix proportions, specifically asphalt and air void contents, on fatigue behavior of asphalt beam specimens in the laboratory tested with four-point bending method of loading. Following the relevant specifications, the strain-controlled mode of loading was selected. Fatigue failure is expected to occur at the cycle which the flexural stiffness of asphalt specimen reduced to 50% of initial amount. Up to a 1,000,000 cycles of loading were applied to each specimen.

Different …

High Temperature Oxidation Characteristics Of Nb-10w-Xcr Alloys, Maria Del Pilar Moricca

Open Access Theses & Dissertations

The use of refractory metals in high temperature applications has been attractive for several years. Systems based on niobium represent a potential new generation of refractory materials systems because of their low density, high melting points, and strength at elevated temperatures. Despite these desirable characteristics, the widespread use of niobium-based alloys is limited because its oxidation resistance is still inadequate for structural applications. Understanding the oxidation kinetics of Nb-based alloys and the role of the different phases in the oxidation process is of crucial importance to improve the oxidation resistance of these materials.

The effect of Cr content on the …

Microstructural Characterization Of Overaged Gtd-111 Hp Turbine Buckets, Oscar Quintero

Open Access Theses & Dissertations

Superalloys are metallic materials that exhibit excellent mechanical strength and creep resistance at high temperatures. They have good surface stability and are corrosion resistant. Superalloys are mostly used in the aerospace industry, gas turbine engines and blades (hot zones of gas turbines), and where extreme heat is encountered. The focus of this research was on the GTD-111 Ni-base superalloy, which is a General Electric (GE) proprietary superalloy mostly used in gas turbine blades with the form of high pressure or first stage buckets. This alloys features better mechanical properties, creep resistance, and a higher stress rupture temperature than the commonly …

Impacting Testing Of High Temperature Ceramics Through The Use Of A Vitiated Heater For Hot And Cold Fire Collisions, Adrian Trejo

Open Access Theses & Dissertations

Material testing is a crucial step during the design process as particular materials serve as safety and life saving conditions. In this study, a MoSi2 is chosen as the target specimen to undergo impact under high temperatures. An impact apparatus is designed and constructed for the purpose of propelling alumina particles at high velocities. A nozzle using compressed nitrogen gas is used to fire the particle at the desired velocities. Due to the possibility of thermal shock occurring at higher temperatures, a separate nozzle utilizing vitiation heating is designed to fire the particle at equally higher temperatures to prove the …

Failure Analysis And Materials Characterization Of Hip Implants, Amanda Marie Bastidos

Open Access Theses & Dissertations

This research focused on the microstructural characterization and failure analysis of hip implant components. The main hip components analyzed were the femoral heads and the ultra-high molecular weight polyethylene (UHMWPE) liners. Previous research has shown that hip implants tend to fail by the PE liners due to adhesive and abrasive wear, delamination, and third body particles (metals, ceramics, and PE). The methods and procedures for analyzing the said failures consisted of non-destructive and destructive evaluations. Non-destructive evaluations included of techniques such as visual characterization and dye penetrant inspection (DPI)-which displayed macroscopic surface details and presented initial clues as to the …

Observed Superspin-Glass Behavior In Ni0.5zn0.5fe2o4 Nanoparticles, Antony Adair

Open Access Theses & Dissertations

In this investigation we seek to identify the magnetic behavior of Ni0.5Zn0.5Fe2O4 nanoparticles though AC-susceptibility and DC-magnetization measurements. Powder x-ray diffraction was performed to determine the purity and average diameter ( ~ 9nm) of the particles. Aditionally, structure was confirmed by comparison through the International Centre for Diffraction Data's Powder Diffraction File [52] (PDF # 08-0234).

Zero-field cooled and field cooled DC magnetization measurements (bifurcation and blocking temperature), as well as M(H) hysteresis (below and above the blocking temperature) lead us to initially suggest that the material may in fact be superparamagnetic. However, further investigation of the real AC susceptibility …

Temperature-Induced Phenomena In Systems Of Magnetic Nanoparticles, Abdul Wazed Bhuiya

Open Access Theses & Dissertations

Magnetic nanoparticle ensembles have received a lot of attention, stemming in part from their current and potential applications in biomedicine and in the development of high-density magnetic storage media. Key to the functionality of these systems are microscopic structures and mechanisms that make them exhibit unique properties and behave differently from their bulk counterparts.

We studied microscopic structures and processes that dictate macroscopic properties, behavior and functionality of magnetic nanoparticle ensembles. As the temperature T strongly influences the magnetic behavior of these systems, we studied temperature dependent magnetic properties using AC-susceptibility and DC-magnetization measurements carried out over a broad range …

Microstructural Characterization And Heat Treatment Of A-286 Turbine Buckets, Christopher Michael Bradley

Open Access Theses & Dissertations

A-286 is an iron-based superalloy used extensively in land-based gas turbines for 2nd stage (low pressure) buckets and 1st and 2nd stage wheels. Although A-286 may appear to some as just another austenitic stainless steel, its elevated temperature properties are attributed to ' precipitate structures, effective distributions of alloy carbides in the forms of M23C6, M6C and MC, and solid solution strengthening. Unfortunately over the course of these components service lives microstructural degradation develops in the form of η-phase formation. The presence of η-phase, especially in large quantities, can have a negative effect on stress rupture properties. Resistance to creep …

Spectroscopic Characterizations Of Organic/Inorganic Nanocomposites, Jayesh Rasikalal Govani

Open Access Theses & Dissertations

Inorganic potassium dihydrogen phosphate (KDP) is widely known for its value as a nonlinear optical material. In this study, pure and l-arginine-doped KDP single crystals were grown by the slow solvent evaporation technique and further subjected to infrared absorption and Raman studies for the confirmation of chemical group functionalization and possible bonding between the organic and inorganic materials. The appearance in the infrared absorption spectra of additional vibrational lines, which mostly originate from disturbed N-H, C-H, and C-N bonds of the l-arginine-doped salt, confirm the interaction between KDP and the organic material. This affirmation is supported by more evidence from …

Effects Of Build Orientation, Aging, And Pre-Conditioning On Mechanical Properties For Stereolithography-Manufactured Astm Type I Specimens Using A Design Of Experiments Approach, Karina Puebla

Open Access Theses & Dissertations

With industry's growing focus on the rapid manufacturing (RM) of end-use products, rapid prototyping (RP) or layered manufacturing (LM) machines that were originally designed to build prototypes may now be required to build functional end-use products. To successfully accomplish the transition, the available materials utilized in RP must provide the performance required for RM. The specific technology used must also be capable of producing repeatable and reproducible parts in regards to mechanical and dimensional properties.

A design of experiments approach was performed to determine the effects of build orientation, aging, and pre-conditioning on the mechanical properties. To perform the investigations, …