Mechanics of Materials Commons^™

Moisture Susceptibility Of Dense Graded Asphalt Concrete Using Cyclic Moistue Induced Stress Tester, Sarvesh Dip Dhakal

Open Access Theses & Dissertations

Moisture damage in asphalt concrete causes loss in mechanical properties of asphalt material due to the presence of moisture in its microstructures in a liquid or a vapor state. Some of the common types of distress observed in asphalt pavements due to moisture damage are stripping (separation of asphalt binder and aggregate), raveling (dislodgement of aggregate particles in asphalt mixture from surface), and hydraulic scour (a process that occurs on a saturated surface by which the pavement material is eroded due to dynamic action of tires in the presence of water). This Thesis focuses on the research on the effects …

Reaction Of Liquid Aluminium- Samarium Alloys With B4c At Ultra High Temperatures, Sanjay Shantha-Kumar

Open Access Theses & Dissertations

Reactive studies between a packed bed of B4C and Al-Sm-Me (Me = Ti, Zr, Hf) alloy melts were carried out under a pseudo-isopiestic thermodynamic system. A graphite enclosure isolated the system under a temperature gradient with one end reaching temperatures greater than 1800 K and the opposite end of the graphite enclosure contains liquid Al with temperatures approximating 950 K. The liquid Al establishes an oxygen potential to control oxidation of very reactive elements (i.e., Al, Sm and Ti). The Al-Sm-Me alloy infuses into a packed bed of B4C reacting exothermically to form borides and carbides depending on the thermodynamic …

High Temperature Oxidation Of Nb-Cr-Mo-Si-B Alloys, Kathryn S. Thomas

Open Access Theses & Dissertations

It has been the trend to use nickel based superalloys in high temperature applications, however higher temperatures are required in the effort to enhance the efficiency of such components as jet turbine engines. The melting temperature of the nickel based superalloy limits the extent to which temperature can be raised as these materials are typically used at temperatures within 200 degrees of their melting point. Refractory metal based systems are attractive due to their high melting points, low densities, and good high temperature strength. However, in such cases as niobium, poor oxidation resistance limits the widespread use of such alloys. …

Defeating Anisotropy In Material Extrusion 3d Printing Via Materials Development, Ángel Ramón Torrado Pérez

Open Access Theses & Dissertations

Additive Manufacturing technologies has been in continuous development for more than 35 years. Specifically, the later denominated Material Extrusion Additive Manufacturing (MEAM), was first developed by S. Scott Crump around 1988 and trademarked later as Fused Deposition Modeling (FDM). Although all of these technologies have been around for a while, it was not until recently that they have been more accessible to everyone. Today, the market of 3D printers covers all ranges of price, from very specialized, heavy and expensive machines, to desktop printers of only a few cubic inches in volume. Until recently, FDM technology had remained somewhat stagnant …

Design And Analysis Of A Novel Latch System Implementing Fiber-Reinforced Composite Materials, Francisco Guevara

Open Access Theses & Dissertations

The use of fiber-reinforced composite materials have increased in the last four decades in high technology applications due to their exceptional mechanical properties and low weight. In the automotive industry carbon fiber have become popular exclusively in luxury cars because of its high cost. However, Carbon-glass hybrid composites offer an effective alternative to designers to implement fiber-reinforced composites into several conventional applications without a considerable price increase maintaining most of their mechanical properties. A door latch system is a complex mechanism that is under high loading conditions during car accidents such as side impacts and rollovers. Therefore, the Department of …

Novel Engineered Nanomaterials For Water Remediation And Gas Adsorption: Graphene Oxide And Carbon Nanotubes Decorated With Metal-Organic Frameworks And Magnetic Nanoparticles, Vahid Jabbari

Open Access Theses & Dissertations

In the current study, a series of novel magnetic and non-magnetic hybrid nanocomposites based on metal-organic frameworks (MOFs) of M3(BTC)2 (M: Ni, Cu, Zn, and Cd), graphene oxide (GrO), and carbon nanotubes (CNTs), and Fe3O4 magnetic nanoparticles (MNPs) were developed via a green, simple and versatile solvothermal method at which GrO and CNT were used as platform to grow the MOFs and Fe3O4 MNPs over them. The as-synthesized nanocomposites were characterized by XRD, SEM, TEM, XPS, IR, Raman, TGA, and N2 adsorption/desorption isotherms. Morphological analysis confirmed successful growth of nano-size Fe3O4 MNPs and M3(BTC)2 MOFs over GrO and CNT platforms. …

A Methodology For Use Of Digital Image Correlation For Hot Mix Asphalt Testing, Estefany Ramos

Open Access Theses & Dissertations

Digital Image Correlation (DIC) is a relatively new technology which aids in the measurement of material properties without the need for installation of sensors. DIC is a noncontact measuring technique that requires the specimen to be marked with a random speckled pattern and to be photographed during the test. The photographs are then post-processed based on the location of the pattern throughout the test. DIC can aid in calculating properties that would otherwise be too difficult even with other measuring instruments.

The objective of this Thesis is to discuss the methodology and validate the use of DIC in different hot …

Acoustic Emission Characteristics Of Damage Accumulation In Kevlar® 49 Composites, Eduardo Andrade

Open Access Theses & Dissertations

Acoustic emission (AE) data attained during tensile testing of epoxy impregnated Kevlar® 49 (K/Ep) composite strands were reduced and analyzed to monitor progressive damage accumulation during the approach to tensile failure. The K/Ep material tested in this study was chosen due to its similarity to the material-of-construction used in composite overwrapped pressure vessels (COPVs) used on the NASA Space Shuttle Orbiter. Insight into the progressive microstructural degradation of K/Ep strands was gained by monitoring AE event rate and energy. Source location based on energy attenuation and arrival time data was used to differentiate between significant AE attributable to microstructural damage …

Novel Endohedral Derivatives Of Sc3n@C2n (N = 34, 40) And Unique Tether Controlled Bis-Functionalization Of Fullerenes, Maira Raquel Ceron Hernandez

Open Access Theses & Dissertations

Since the discovery of fullerenes in 1985, their exohedral functionalization has been necessary to increase their solubility and explore their properties and potential applications in materials science and medicinal chemistry. This Thesis provides a short overview of the importance of electronic, size and shape complementarity in determining the structures of specific endohedral fullerene compounds. This is followed by a description of a new method for the separation of scandium nitride endohedral fullerenes Sc3N@C2n (n = 34, 39 and 40), and their monofunctionalization.

We also present the regioselective synThesis of easily isolable bis-derivatives of C60, C70, and M3N@Ih-C80 (M = Sc, …

Transition States And Modeling For Co9s8/Mos2 Catalysis, Gabriel Angel Gonzalez

Open Access Theses & Dissertations

Transition state computational studies of the sulfur removal from dibenzothiophene (DBT) molecule have herein been performed considering the Co9S8/MoS2 interface existing on unsupported Co/MoS2 catalysts. The linear synchronous transit (LST) and quadratic synchronous transit (QST) methods integrated in a density functional theory (DFT) program such as Dmol3 were used for the calculations of energy barriers of the transition states. Three different configurations present on the Co9S8/MoS2 interface have been envisaged as possible catalytic sites: sulfur-sulfur (S, S) sites, and molybdenum-sulfur (Mo, S) and molybdenum-molybdenum (Mo, Mo) edge sites. This study revealed that the (Mo, Mo) edge site is the most …

An Improved Sin-Hyperbolic Constitutive Model For Creep Deformation And Damage, Mohammad Shafinul Haque

Open Access Theses & Dissertations

Inspection and maintenance of industrial gas turbines (IGTs) cost millions of dollars. Growing demand of obtaining higher IGT efficiency leads to higher temperature and pressure operating conditions. Long exposure of turbine components at elevated temperature and pressure

makes creep damage critically important to consider during planning, designing and operating conditions. Effective and economic maintenance requires accurate creep deformation, damage

evolution and rupture life prediction information. Creep prediction models are used to determine the state of the turbine components and to schedule the inspection, maintenance and replacement time periods. The more accurate the prediction model, the less is the overall cost …

Transition Metal Carbide (Tmc) Novel Materials For Novel Catalytic Applications, Svetlana Lagoykina

Open Access Theses & Dissertations

Transition metal carbides (TMC) constitute a diverse class of materials and traditionally have many technological applications. TMC became a subject of extensive research since 1973, when their platinum -like properties were discovered. They demonstrated high catalytical activity and selectivity in a variety of chemical reaction and have potential for some novel catalytic application.

This research is an effort to design new high effective, selective and stable bimetal or alkali promoted TMC catalyst. After extensive theoretical research a wide range of TMC, including bimetal and alkali promoted carbides, were synthesized by different methods. All solids were characterized by XRD and microscopy. …

Thermal Shock Studies On Carbon-Carbon Composites: Experimentation And Analysis, Alma Lucia Leanos

Open Access Theses & Dissertations

The oxidation behavior of C/C composites under thermal shock conditions in air is understood and predicted experimentally and by computational efforts. In Chapter. 1, both compressive properties and oxidation behavior of pristine and thermal shock exposed 2D C/C composite specimens were examined. Pristine test specimens were exposed to thermal shock conditions with temperatures ranging from 400°C to 1000°C in an oxidizing environment, followed by compression tests on pristine and thermal shock exposed specimens to obtain their compressive responses.

Similarly, in Chapter. 2, the influence of thermal shock conditions on both, the extent of carbon materials decomposition and the through-thickness compressive …

3d Printing Technology Using High Viscous Materials-Synthesis Of Functional Materials And Fabrication Of 3d Metal Structure, Seongik Hong

Open Access Theses & Dissertations

In the 3D printing technology, the research for using various materials has been performing. In this research work, 3D printable high viscous materials are suggested as one of the solutions for problems in the traditional 3D printing technology.

First, Cu-Ag coreshell was synthesized as a functional material. In terms of the reaction rate, reaction rate limiting step was defined as a fundamental research, and then prepared Cu-Ag coreshell was printed and analyzed. Second, the high viscous Cu paste was prepared and then metal 3D printed structure was fabricated by using new printing method.

In the synThesis of Cu-Ag coreshell, different …

Characterization Of High-Purity Niobium Structures Fabricated Using The Electron Beam Melting Process, Cesar Adrian Terrazas

Open Access Theses & Dissertations

Additive Manufacturing (AM) refers to the varied set of technologies utilized for the fabrication of complex 3D components from digital data in a layer-by-layer fashion. The use of these technologies promises to revolutionize the manufacturing industry. The electron beam melting (EBM) process has been utilized for the fabrication of fully dense near-net-shape components from various metallic materials. This process, catalogued as a powder bed fusion technology, consists of the deposition of thin layers (50 - 120µm) of metallic powder particles which are fused by the use of a high energy electron beam and has been commercialized by Swedish company Arcam …

3d Printed Electromagnetic Transmission And Electronic Structures Fabricated On A Single Platform Using Advanced Process Integration Techniques, Paul I. Deffenbaugh

Open Access Theses & Dissertations

3D printing has garnered immense attention from many fields including in-office rapid prototyping of mechanical parts, outer-space satellite replication, garage functional firearm manufacture, and NASA rocket engine component fabrication. 3D printing allows increased design flexibility in the fabrication of electronics, microwave circuits and wireless antennas and has reached a level of maturity which allows functional parts to be printed. Much more work is necessary in order to perfect the processes of 3D printed electronics especially in the area of automation. Chapter 1 shows several finished prototypes of 3D printed electronics as well as newly developed techniques in fabrication. Little is …

Optimization Of Uv-Led Curable Printing Material For Applications In Direct Writing Systems: Inkjet, Reverse Offset, And Micro Dispensing Gpd, Ada Judith Ortega Varela

Open Access Theses & Dissertations

The quality of a product fabricated by direct writing methods will depend greatly on the properties of the printing material and its compatibility with the printing process. Although multiple advances in developing printing inks and pastes with novel properties are being made, the potential those can bring to electronics is hindered by their stability and performance during the printing process. In this study a UV-LED curable acrylic material was used to test the optimization of inks and pastes for three of the most common direct writing systems: Piezo-type Inkjet, Reverse Offset Roll to Plate, and Micro Deposition. The viscosity of …

Hydrogen Generation From Ammonia Borane And Water Through The Combustion Reactions With Mechanically Alloyed Al/Mg Powder, Daniel Rodriguez

Open Access Theses & Dissertations

Finding and developing a safe and effective method for hydrogen storage is integral to its use as an alternative source of energy. The goal of the studies described in this Thesis was to investigate the feasibility of developing combustible hydrogen-generating compositions based on ammonia borane and novel energetic materials such as nanocomposite and mechanically alloyed reactive materials, recently obtained by Prof. Edward Dreizin's team at the New Jersey Institute of Technology (NJIT). Such compositions could be stored for long time and release hydrogen on demand, upon ignition. The first phase of the research included thermodynamic calculations for combustion of ammonia …

Effect Of Rhenium On Short Term Oxidation Of Niobium Based Alloys For High Temperature Applications, Ruth M. Sierra

Open Access Theses & Dissertations

The effect of adding Re to Nb-based alloys and is intended to analyze in depth the microstructures of Nb based alloys with Re, Si and Cr additions, in atomic percentages. The binary alloys (Nb-5Re, Nb-5Si and Nb-5Cr) reveal the formation of a single phase, NbSS, NbSS+ Nb3Si and NbSS+NbCr2 respectively. The formation of the single phase was confirmed by TEM studies for the Nb-5Re alloy. Addition of Re to form ternary alloys, has helped in the formation of Nb5Si3 and (Nb, Re) Cr2, in Nb-5Re- 5Si and Nb-5Re-5Cr respectively. Quaternary alloy Nb-5Re-5Si-5Cr has Nb5Si3, NbCr2 and NbSS. The oxidation behavior …

Characterization Of W-Ti-O Thin Films For Application In Photovoltaics, Amanda Patricia Christmas

Open Access Theses & Dissertations

Photovoltaic (PV) devices consist of the conversion of light energy into electricity. Nearly all PV technologies employ transparent conducting oxides (TCO) as an integral part of the de-vice structure so that the light can reach the semiconductor. The predominant transparent conducting oxide (TCO) that is currently being used in industry is indium tin oxide (ITO). However, Indium (In) is high in cost and becoming scarce in the world. This work is focused towards Titanium doped Tungsten oxide (WO3) for TCO application. The ultimate goal is making novel, cheaper, and efficient TCOs based on W-Ti-O films. Titanium will enhance the conductivity …

Nanometric Structure-Property Relationship In Hafnium Oxide Thin Films Made By Sputter-Deposition, Mirella Vargas

Open Access Theses & Dissertations

Hafnium oxide (HfO2) is technologically an important material, which exhibits a unique set of properties such as a high dielectric constant (k~25) and wide band gap (~5.7 eV) which make this material attractive in the fields of microelectronics and optoelectronics. HfO2 has become the leading candidate to replace SiO2 dielectrics in gate oxides due to a higher permittivity and reportedly lower electron tunneling effects. HfO2 exhibits various polymorphs; the thermodynamic stability and phase existence depends on the temperature and pressure conditions. In addition, the controlled growth and manipulation of specific HfO2 crystal structures at the nanoscale dimensions is the driving …

Alkali Promoted Molybdenum (Iv) Sulfide Based Catalysts, Development And Characterization For Alcohol Synthesis From Carbon Monoxide And Hydrogen, Belinda Delilah Molina

Open Access Theses & Dissertations

For more than a century transition metal sulfides (TMS) have been the anchor of hydro-processing fuels and upgrading bitumen and coal in refineries worldwide. As oil supplies dwindle and environmental laws become more stringent, there is a greater need for cleaner alternative fuels and/or synthetic fuels. The depletion of oil reserves and a rapidly increasing energy demand worldwide, together with the interest to reduce dependence on foreign oil makes alcohol production for fuels and chemicals via the Fischer Tropsch synthesis (FTS) very attractive. The original Fischer-Tropsch (FT) reaction is the heart of all gas-to-liquid technologies; it creates higher alcohols and …

Growth And Analysis Of Micro And Nano Cdte Arrays For Solar Cell Applications, Brandon Adrian Aguirre

Open Access Theses & Dissertations

CdTe is an excellent material for infrared detectors and photovoltaic applications. The efficiency of CdTe/CdS solar cells has increased very rapidly in the last 3 years to ~20% but is still below the maximum theoretical value of 30%. Although the short-circuit current density is close to its maximum of 30 mA/cm2, the open circuit voltage has potential to be increased further to over 1 Volt. The main limitation that prevents further increase in the open-circuit voltage and therefore efficiency is the high defect density in the CdTe absorber layer. Reducing the defect density will increase the open-circuit voltage above 1 …

Combustion Synthesis Of Molybdenum Silicides And Borosilicides For Ultrahigh-Temperature Structural Applications, Mohammad Shafiul Alam

Open Access Theses & Dissertations

Molybdenum silicides and borosilicides are promising structural materials for gas-turbine power plants. A major challenge, however, is to simultaneously achieve high oxidation resistance and acceptable mechanical properties at high temperatures. For example, molybdenum disilicide (MoSi₂) has excellent oxidation resistance and poor mechanical properties, while Mo-rich silicides such as Mo₅Si₃ (called T₁) have much better mechanical properties but poor oxidation resistance. One approach is based on the fabrication of MoSi₂−T₁ composites that combine high oxidation resistance of MoSi₂ and good mechanical properties of T₁. Another approach involves the …

Gadolinia Doped Hafnia (Gd2o3- Hfo2) Thermal Barrier Coatings For Gas Turbine Applications, Satya Kiran Gullapalli

Open Access Theses & Dissertations

Thermal efficiency of the gas turbines is influenced by the operating temperature of the hot gas path components. The material used for the hot gas path components can only withstand temperature up to a certain limit. Thermal barrier coatings (TBC) provide the additional thermal protection for these components and help the gas turbine achieve higher firing temperatures. Traditionally available yttria stabilized zirconia (YSZ) TBCs have a limitation up to 1200 C due to their phase transformation. The present work focuses on gadolinia based hafnia (GSH) TBCs to study their potential to replace the YSZ coatings. Different compositions of gadolinia doped …

Design Of Three Different Particle Size Distributions In Silver Paste Through Computer Simulation For Higher Electrical Conductivity, Kyungdeok Jang

Open Access Theses & Dissertations

In the field of printed electronics technology, researchers have tried to print highly conductive electrodes with fine width and height in order to manufacture high performance devices.

The purpose of this research is to print particle monolayer silver patterns which have better electrical conductivity than existing ones. The key idea of this experiment is to analyze silver inks with different sized particles. Let us consider a particle monolayer pattern printed with silver ink consisting of mono-sized particles. Inside of the pattern, there are some vacant spaces between the particles, which can lead to low electrical conductivity and discontinuity of the …

Fabrication Of A Nickel-Based Superalloy In Electron Beam Melting And Process Improvements Using Thermal Feedback From A Multi-Wavelength Pyrometer, Jonathan Minjares

Open Access Theses & Dissertations

The focus of this research was to fabricate parts composed of a nickel-based superalloy containing high levels of aluminum and titanium (NSAT) by using electron beam melting (EBM) additive manufacturing (AM) technology and utilizing thermal feedback from a multi-wavelength pyrometer to perform process improvements leading to near defect-free parts. EBM is an AM technology that utilizes metal powder to fabricate parts in layer-by-layer manner. A multi-wavelength pyrometer was implemented in an Arcam S12 (Arcam AB, Sweden) EBM system to observe and record surface temperatures throughout fabrication. Temperature data from the EBM system and the multi-wavelength pyrometer were graphed using MATLAB …

A Study Of Ti-Doped Wo3 Thin Films Using Comparative Theoretical And Experimental Approach, Aurelio Paez

Open Access Theses & Dissertations

Metal oxides like Tungsten Oxide (WO3) are well documented and characterized in the literature, with uses in darkening windows and mirrors, flat computer displays, solar panel cooling, and sensors (of interest in this study). Ti doping of WO3 is less documented and the focus of this study. Sample thin films of pure WO3 and varyingly Ti doped WO3 were prepared using Radio Frequency magnetron sputtering (RF) (13.56 MHz) to grow thin films on a silicon substrate. This study aims to compare multiple Ti doping percentages in WO3 theoretically and then compare with experimental data taken from thin films of various …

Structural, Optical And Electrical Properties Of Yttrium-Doped Hafnium Oxide Nanocrystalline Thin Films, Abhilash Kongu

Open Access Theses & Dissertations

Hafnium oxide (HfO2) has emerged as the most promising high-k dielectric for Metal-Oxide-Semiconductor (MOS) devices and has been highlighted as the most suitable dielectric materials to replace silicon oxide because of its comprehensive performance. In the present research, yttrium-doped HfO2 (YDH) thin films were fabricated using RF magnetron sputter deposition onto Si (100) and quartz with a variable thickness. Cross-sectional scanning electron microscopy coupled with Filmetrics revealed that film thickness values range from 700 A° to 7500 A°. Electrical properties such as AC Resistivity and current-voltage (I-V) characteristics of YDH films were studied. YDH films that were relatively thin (<1500 A°) crystallized in monoclinic phase while thicker films crystallized in cubic phase. The band gap (Eg) of the films was calculated from the optical measurements. The band gap was found to be ∼5.60 eV for monoclinic while it is ∼6.05 eV for cubic phase of YDH films. Frequency dependence of the electrical resistivity (ρac) and the total conductivity of the films were measured. Resistivity decreased (by three orders of magnitude) with increasing frequency from 100 Hz to 1 MHz, attributed due to the hopping mechanism in YDH films. Whereas, while ρac∼1Ω-m at low frequencies (100 Hz), it decreased to ∼ 104 Ω-cm at higher frequencies (1 MHz). Aluminum (Al) metal electrodes were deposited to fabricate a thin film capacitor with YDH layer as dielectric film thereby employing Al-YDH-Si capacitor structure. The results indicate that the capacitance of the films decrease with increasing film thickness. A detailed analysis of the electrical characteristics of YDH films is presented.

Microstructure And Mechanical Properties Of Titanium Nitride Optical Coatings Made By Dc Magnetron Sputtering, Gustavo Martinez

Open Access Theses & Dissertations

Titanium nitride (TiNx) thin films were grown by DC (Direct Current) magnetron sputtering method onto Si(100) substrates by varying time of deposition to produce films with variable thickness (dTiN) in the range of 20-120 nm. The grown TiNx films were characterized by studying their structure, composition, and mechanical properties. Nuclear reaction analysis (NRA) combined with Rutherford backscattering spectrometry (RBS) analyses indicate that the grown films were stoichiometric TiN. Grazing incidence X-ray diffraction (GIXRD) measurements indicate that the texturing of the TiN films changes as a function of dTiN. The (111) and (002) peaks appear initially; with increasing dTiN, (111) becomes …