Mechanics of Materials Commons^™

A Multi-Scale Based Model For Composite Materials With Embedded Pzt Filaments For Energy Harvesting, A.E. El-Etriby, M.E. Abdel-Meguid, K.M. Shalan, Tarek Hatem, Yehia Bahei-El-Din

Centre for Advanced Materials

Ambient vibrations are major source of wasted energy, exploiting properly such vibration can be converted to valuable energy and harvested to power up devices, i.e. electronic devices. Accordingly, energy harvesting using smart structures with active piezoelectric ceramics has gained wide interest over the past few years as a method for converting such wasted energy. This paper provides numerical and experimental analysis of piezoelectric fiber based composites for energy harvesting applications proposing a multi-scale modeling approach coupled with experimental verification. The multi-scale approach suggested predicting the behavior of piezoelectric fiber-based composites use micromechanical model based on Transformation Field Analysis (TFA) to …

High Strength Steel Fiber Reinforced Flow-Able Or Scc Concrete With Variable Fiber By Volume Fractions For Thin Plate And Shell Structures, Abebe Berhe

UNLV Theses, Dissertations, Professional Papers, and Capstones

The purpose of this study is to incorporate discrete, short, mechanically deformed, small diameter steel fibers into high strength concrete with f'c > 70 MPa (10 ksi) in an attempt to reduce and partially eliminate the need for steel rebar in concrete construction. By introducing steel fibers to high strength concrete mixture, the overall tensile, compressive and shear strength of the mixture can be improved immensely thus, replacing portions or major parts of the longitudinal, temperature and shrinkage reinforcements. The reduction or elimination of longitudinal and transverse reinforcements in the construction of structural or non-structural members can result in savings in …

Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith

Master's Theses

Mode I interlaminar fracture of 3k 8-Harness-Satin Carbon cloth, with identical fill and weft yarns, pre-impregnated with Newport 307 resin was investigated through the DCB test (ASTM D5528). Crack propagations along both the fill and weft yarns were considered for both post-bonded (co-bonded) and co-cured laminates. A patent-pending delamination insertion method was compared to the standard Teflon film option to assess its applicability to mode I fracture testing. The Modified Beam Theory, Compliance Calibration method, and Modified Compliance Calibration method were used for comparative purposes for these investigations and to evaluate the validity of the proposed Equivalent Stiffness (EQS) method. …

Compression Testing And Failure Modes Of Steel-Concrete Composite (Sc) Structures For Nuclear Containment, Patrick Michael Wanamaker, Amit H. Varma

The Summer Undergraduate Research Fellowship (SURF) Symposium

Although being able to provide much cleaner power than burning coal and other fossil fuels, nuclear power plants are still a tough sell to the general public due to their history of being spontaneously dangerous. The containment structures surrounding these nuclear plants, however, can play a huge role in reducing the risks associated with them. Relatively new designs for these containment assemblies, known as SC (steel-concrete composite) structures, aim to increase the strength and durability of the containment facilities while keeping costs down. By varying the spacing between shear studs, the ratio of concrete to steel, and the ratio of …

Materials Education And Research In Art And Design: A New Role For Libraries (Survey Stats), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Sheet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Booklet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Website), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Collection Creation And Administration: A New Role For Libraries (White Paper), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

The Problem/Opportunity: To define, identify, and guide design-based materials collections in academic settings and foster community among those with existing collections and/or those considering creating and supporting one.

Contents and topics:

1. What is a materials collection?
2. Why have a materials collection?
3. Acquisition strategies
4. Organizational approaches
5. Programming possibilities
6. Symposium summary
7. Resources

Low Velocity Impact Tower Feasibility, Setup, And Impact Testing Of Carbon Fiber Reinforced Epoxy Thermoset And Peek Thermoplastic Matrix Composites, Brent Plehn

Materials Engineering

A low velocity impact tower was donated to Cal Poly's Materials Engineering Department along with four fiber reinforced polymer matrix composites. The tower was set up in building 192 in the Mechanical Testing Laboratory. Improvements were made to the tower including adding velocity detection capabilities, making loose hardware inclusive, adding an extra tower arm for better consistency, adding a double jawed clamp for faster testing, and rerouting the tower's compressed air system to improve performance. A standard operating procedure was drafted, tested, and redrafted for impact testing composite panels. The four composite panels consisted of two quasi-isotropic 16 ply AS-1 …

Stress Analysis Of Ramberg-Osgood And Hollomon 1-D Axial Rods, Ronald J. Giardina Jr

LSU New Orleans Theses and Dissertations

In this paper we present novel analytic and finite element solutions to 1-D straight rods made of Ramberg-Osgood and Hollomon type materials. These material models are studied because they are a more accurate representation of the material properties of certain metals used often in manufacturing than the simpler composite linear types of stress/strain models. Here, various types of loads are considered and solutions are compared against some linear models. It is shown that the nonlinear models do have manageable solutions, which produce important differences in the results - attributes which suggest that these models should take a more prominent place …

Fatigue Testing And Data Analysis Of Welded Steel Cruciform Joints, Alina Shrestha

LSU New Orleans Theses and Dissertations

In this study, ABS Publication 115, “Guidance on Fatigue Assessment of Offshore Structures” is briefly reviewed. Emphasis is on the S-N curves based fatigue assessment approach of non-tubular joints, and both size and environment effects are also considered. Further, fatigue tests are performed to study the fatigue strength of load-carrying and non-load-carrying steel cruciform joints that represent typical joint types in marine structures. The experimental results are then compared against ABS fatigue assessment methods, based on nominal stress approach, which demonstrates a need for better fatigue evaluation parameter. A good fatigue parameter by definition should be consistent and should correlate …

Creep, Fatigue And Creep-Fatigue Interactions In Modified 9% Cr - 1% Mo (P91) Steels, Valliappa Kalyanasundaram

Graduate Theses and Dissertations

Grade P91 steel, from the class of advanced high-chrome ferritic steels, is one of the preferred materials for many elevated temperature structural components. Creep-fatigue (C-F) interactions, along with oxidation, can accelerate the kinetics of damage accumulation and consequently reduce such components' life. Hence, reliable C-F test data is required for meticulous consideration of C-F interactions and oxidation, which in turn is vital for sound design practices. It is also imperative to develop analytical constitutive models that can simulate and predict material response under various long-term in-service conditions using experimental data from short-term laboratory experiments. Consequently, the major objectives of the …

Plastic Deformation Of Astm A36 Steel Using Two-Stage Light Gas Gun, Shawoon Kumar Roy

College of Engineering: Graduate Celebration Programs

To characterize material deformation in high velocity impact. To validate material models for computation simulation purposes.

This ongoing research is an attempt to study the plastic deformation of A36 steel plate (0.5” thick) under hypervelocity impact. Plastic deformation of the target plate was simulated using finite element software LS-DYNA.

Analysis Of Bolted Joints Under Medium And High Impact Loading, Deepak Sankar Somasundaram, Mohamed Trabia, Brendan J. O'Toole

College of Engineering: Graduate Celebration Programs

• Develop test fixture for medium impact study on bolted joints
• Create FEA model that can replicate the experiment
• Develop test fixture for high impact loading
• Create FEA model and select material properties that can produce results that
  closely match experiments.
• Compare different modeling techniques for high impact loading

A Resistance Based Structural Health Monitoring System For Composite Structure Applications, Dennis N. Boettcher

Master's Theses

This research effort explored the possibility of using interwoven conductive and nonconductive fibers in a composite laminate for structural health monitoring (SHM). Traditional SHM systems utilize fiber optics, piezoelectrics, or detect defects by nondestructive test methods by use of sonar graphs or x-rays. However, these approaches are often expensive, time consuming and complicated.

The primary objective of this research was to apply a resistance based method of structural health monitoring to a composite structure to determine structural integrity and presence of defects.

The conductive properties of fiber such as carbon, copper, or constantan - a copper-nickel alloy - can be …

Peridynamic Model For Dynamic Fracture In Unidirectional Fiber-Reinforced Composites, Wenke Hu, Youn Doh Ha, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

We propose a computational method for a homogenized peridynamics description of fiber-reinforced composites and we use it to simulate dynamic brittle fracture and damage in these materials. With this model we analyze the dynamic effects induced by different types of dynamic loading on the fracture and damage behavior of unidirectional fiber-reinforced composites. In contrast to the results expected from quasi-static loading, the simulations show that dynamic conditions can lead to co-existence of and transitions between fracture modes; matrix shattering can happen before a splitting crack propagates. We observe matrix–fiber splitting fracture, matrix cracking, and crack migration in the matrix, including …

The Effects Of Damage Arrestment Devices In Composite Plate Sandwiches With Fastener Holes, Mark Anderson, Nancy Hung Choy, Lacey Jones, Rita Kourskaya

Aerospace Engineering

Composite materials such as a carbon fiber are used in a variety of new technologies including aircraft, spacecraft, and motor vehicles. Carbon fiber has a high strength to weight ratio, a key advantage over other material options. This report discusses the use of composite damage arrestment devices (DADs) in composite sandwich panels with a foam core. There are three different curing cycles tested for the DADs: pressure only, vacuum only, and vacuum with 1000 lbs of pressure. Using a Tetrahedron Heat Press to cure the composite specimen and an Instron Machine to perform tensile testing, data was collected for each …

Design, Fabrication, Structural Testing, And Numerical Analysis Of A Small Scale Composite Wing, Jacob David Gaunt, Juan Carlos Flores, Vincent Andrew Perry

Aerospace Engineering

A small scale composite wing based on a design found on an experimental aircraft was designed, constructed, and tested dynamically and statically. The wing was constructed similarly to an experimental aircraft wing. The performed static test was intended to produce pure bending. Strain gages were used to measure strains on the wing structure. The strains were converted to stresses to aid in analysis. The static test results suggested that the wing was actually under torsion. Four structural modes were found from the static test. A finite element analysis model was made to compare experimental results to numerical analytical results. The …

Multiscale Transformation Field Analysis Of Progressive Damage In Fibrous Laminates, Yehia Bahei-El-Din, Ritesh Khire, Prabhat Hajela

Centre for Advanced Materials

As part of an ongoing effort to model uncertainty propagation across multiple scales in fibrous laminates, this paper presents a deterministic transformation field analysis for modeling damage progression under membrane forces and bending moments. In this approach, equivalent eigenstresses are computed in the phases and/or plies such that their respective stress components that satisfy the underlying failure criteria are reduced to zero. Superposition of the solutions found for the undamaged laminate under applied loads and under the eigenstress field provide the entire response. Failure criteria are based on stress averages in the fiber and matrix. Damage mechanisms considered are frictional …

Modified Sandwich Structures For Improved Impact Resistance Of Wind Turbine Blades, Yehia Bahei-El-Din, Mostafa Shazly, I. El-Habbal, Y. Elbahy

Centre for Advanced Materials

Wind turbine blades are susceptible to damage due to fatigue as well as impact by flying objects and parts broken off failed blades of nearby wind towers. Localized, permanent compression of the foam core and delamination of the fibrous composite face sheets are typical damage modes and can lead to progressive structural failure. Sandwich structures modified by inclusion of flexible polyurethane (PU) layers within the cross section are examined under both impact and dynamic loads. Finite element models of sandwich structures with conventional and modified designs show that sandwich designs modified with PU interlayes exhibit reduced foam core crushing and …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Multiscale Modeling Of Impact On Heterogeneous Viscoelastic Solids With Evolving Microcracks, Flavio V. Souza

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Multiscale computational techniques play a major role in solving problems related to viscoelastic composite materials due to the complexities inherent to these materials. In the present work, a numerical procedure for multiscale modeling of impact on heterogeneous viscoelastic solids containing evolving microcracks is proposed in which the (global scale) homogenized viscoelastic incremental constitutive equations have the same form as the local scale viscoelastic incremental constitutive equations, but the homogenized tangent constitutive tensor and the homogenized incremental history dependent stress tensor depend on the amount of damage accumulated at the local scale. Furthermore, the developed technique allows the computation of the …

Development Of Low Temperature Alpha Alumina Coatings By Ac Magnetron Sputtering, Andrew Cloud

Mechanical Engineering Undergraduate Honors Theses

Alpha-phase aluminum oxide thin films were created using an Isoflux ICM-10 dual target inverted cylindrical magnetron sputtering system using mid-frequency AC power supplies. Alpha alumina films were deposited at a magnetron power of 6 kW, 50% oxygen partial pressure by volume, and -35 V DC bias. Film thickness, substrate material, and position and orientation within the deposition chamber were varied. To ensure the deposition conditions are suitable for alloys, the substrate temperature was measured using temperature indicating liquids. The experimental results, supported by Explicit Euler numerical analysis, revealed a steady state temperature of ~480°C at 6kW. Transmission electron microscopy (TEM) …

Residual Stress Characterization In Structural Materials By Destructive And Nondestructive Techniques, Ajit K. Roy, Anand Venkatesh, Vikram Marthandam, Satish Dronavalli, Douglas P. Wells, Ronald Rogge

Mechanical Engineering Faculty Research

Transmutation of nuclear waste is currently being considered to transform long-lived isotopes to species with relatively short half-lives and reduced radioactivity through capture and decay of minor actinides and fission products. This process is intended for geologic disposal of spent nuclear fuels for shorter durations in the proposed Yucca Mountain repository. The molten lead-bismuth-eutectic will be used as a target and coolant during transmutation, which will be contained in a subsystem vessel made from materials such as austenitic (304L) and martensitic (EP-823 and HT-9) stainless steels. The structural materials used in this vessel will be subjected to welding operations and …

Stability Design Of A Slender Column With Curved Longitudinal Stiffeners, Mark S. Lake

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis presents the results of a stability design study of a slender column with curved longitudinal stiffeners for large space structure applications. The stiffened column concept is attractive because it allows the buckling load of a slender column to be increased at a fairly low cost in increased mass, and at no change in the column packaged size. Linear stability analyses are performed using a "linked-plate" representation of the stiffeners to determine stiffener local buckling stresses. Results from a set of parametric analyses are used to determine an approximate explicit expression for stiffener local buckling in terms of its …

Studies Of Fracture And Deformed Surfaces Of High Strength Aluminum Alloys By X-Ray Diffraction, Tamma K. Kumar

Mechanical & Aerospace Engineering Theses & Dissertations

X-ray observations of fatigue fracture and deformed surfaces of 7075-T6 aluminum were conducted in this study. The (111) and (222) diffraction peaks were obtained from the fractured and deformed surfaces. It was observed that in comparison with the base metal, the fracture exhibited line broadening similar to that due to cold working. The broadening is indicative of plastic deformation in the vicinity of the advancing crack tip during the fracture process. Also the different regions of fracture exhibited varying degrees of line broadening. With respect to the fatigue crack, the slow crack growth region showed a greater broadening, and, hence, …

Comparative Study Of Lightweight And Normal Weight Concrete In Flexure, Mohammad Zareh

Dissertations and Theses

This investigation represents a comparative study of the flexural behavior of lightweight and normal weight concrete. Both theoretical and experimental moment-curvature characteristics of the tested specimens were used to study the flexural behavior.

A generalized computer program to determine the moment-curvature relationships of a singly reinforced rectangular concrete beam was developed.

For this limited study it was observed that lightweight concrete beams when compared to normal concrete beams achieve comparable moment capacity (about 92% of normal weight concrete) but exhibit higher deflections (about 40% more than normal weight concrete).

Concrete In Dairies, D Roger Buchanan

Journal of the Department of Agriculture, Western Australia, Series 4

PRIME requirements for exposed concrete surfaces in dairies are that they should be easily cleansed and should not deteriorate in contact with milk and milk products.

In milking stalls, animal races and on loading platforms hardwearing surfaces which offer good foothold are also necessary.