Engineering Mechanics Commons^™

Magnetic Field-Induced Transformation In Polycrystalline Ni2mnal Heusler Type Magnetic Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely, Laura N. Bartlett

Materials Science and Engineering Faculty Research & Creative Works

The martensitic and magnetic transformations, as well as the mechanical properties, of Ni₂MnAl alloys in as-cast (AC) and heat-treated (HT) conditions were investigated. Magnetic-field-induced strain was evaluated via magnetostriction, with reversible strains of 0.14% and 0.2% achieved in the martensitic phase at 2 K for the AC and HT alloys, respectively. Transformation temperatures and Curie temperatures were determined under constant applied magnetic field, revealing that γ-phase inclusions in the AC microstructure suppress antiferromagnetic domain response, yielding a lower magnetization (∼8.4 emu g⁻¹) compared to the HT alloy (∼13.4 emu g⁻¹). Both alloys exhibited hysteretic behavior in the martensitic state and …

Me3329 Modular Phonograph Gearbox, Garrett Andrik Leighton, Preston Robert Hupe, Gavin Carter Ebner, Andrew Renato Reyes

Mechanical Engineering

The Mechanical Engineering Department at California Polytechnic State University, San Luis Obispo (Cal Poly), seeks to develop a laboratory tool allowing students to reinforce concepts of gears for Mechanical Systems Design (ME329). Some current laboratories do not provide students with hands-on interaction, and the department lacks equipment and documentation to support a standardized lab. With ME329 expanding from ten to fifteen weeks, there is an opportunity to create a physical gearbox design lab allowing students to reinforce lecture material in engaging ways, while standardizing student learning. This senior project is presented and sponsored by Professor Alan Zhang. It will be …

Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely

Materials Science and Engineering Faculty Research & Creative Works

All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

Critical Parameters Controlling Oxide Scale Formation And Hydro-Descaling Efficiency During Steelmaking, Tochukwu Princewill Ojiako

Doctoral Dissertations

In modern steelmaking, cast slabs are exposed to high-temperature oxidizing environments during secondary cooling, reheating, and hot rolling, resulting in the formation of multilayer oxide scales on the steel surface. These scales interact with mold-flux residues originating from the casting process (CC). The morphology, chemistry, and adhesion of oxide scale strongly influence its removability during high-pressure hydraulic descaling and ultimately determine the surface quality of hot-rolled products. However, the mechanistic relationship between oxide scale evolution, scale-steel interfacial structure, and hydraulic descaling performance remains poorly understood.

This dissertation investigates oxide scale formation, modification, and removal in low-carbon thin-slab steels produced by …

Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size, Ugochukwu Agbedo, Mario Buchely, Laura Bartlett, Caelan Kennedy

Materials Science and Engineering Faculty Research & Creative Works

Accurate prediction of the critical transformation temperatures Ac1 and Ac3 is one of the essential factors in the heat treatment of CA6NM cast martensitic stainless steel. In this study, the influence of alloy composition, heating rate, and prior austenite grain size on the critical temperatures was quantified using dilatometric measurements and statistical modeling. Six heat treatment conditions produced prior austenite grain sizes ranging from ~75 to 247 µm. Experimental results showed that grain size variations produced only minor changes in Ac1 and Ac3, indicating a weak dependence of transformation temperatures on prior austenite grain size within the investigated range. In …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Investigations On The Fatigue Strength Of Threads Produced By Different Fabrication Techniques, Philippe Du Maire, Jürgen Hoffmeister, Andreas Öchsner, Michael Johlitz

15th International Conference on Shot Peening

The increasing importance of sustainability in engineering demands the development of long-lasting, high-performance components that reduce material and energy consumption over time. This study investigates how different thread manufacturing processes, i.e., cutting, rolling, and deep rolling, affect the fatigue strength of bolts made from 42CrMo4+QT steel. Cylindrical specimens with M12 threads were subjected to cyclic tensile loading with constant mean stress. Fatigue strength was evaluated using the staircase method, and supporting analyses included X-ray diffraction for residual stress, and full width half maximum examination and Vickers microhardness measurements. Results show that thread rolling significantly improves fatigue strength, achieving 113.8 MPa …

Expansion Of Laser Peening Application With A High-Power Microchip Laser On A Robotic Arm, Yuji Sano, Yoshio Mizuta, Satoshi Tamaki, Tomonao Hosokai, Tomoharu Kato, Yoshihiro Sakino, Volker Schneidau, Sebastian Holz, Jörg Behler

15th International Conference on Shot Peening

Laser peening (LP) introduces compressive residual stress (RS) onto the surface of metallic materials using nanosecond laser pulses irradiated through a water layer, thereby effectively suppressing fatigue crack initiation. However, conventional LP systems require large, stationary setups, restricting their use to indoor environments. To overcome this limitation, a portable LP device featuring a finger-sized microchip laser mounted on a collaborative robot arm has been developed. Equipped with a compact power supply and a water circulation/recovery system, the device can operate on-site with minimal setup. Successful processing across various materials has confirmed both compressive RS induction and fatigue life extension. Notably, …

Effects Of Laser Peening On Fatigue Properties Of Welded Aluminum Thin Plates, Kiyotaka Masaki, Yoshio Mizuta, Satoshi Tamaki, Yuji Sano

15th International Conference on Shot Peening

To improve the fatigue properties of welded aluminum alloy thin plates used in transportation machinery, handheld laser peening (HH-LP) was applied to 2 mm-thick A5083-O specimens prepared by bead-on TIG welding. Conventional laser peening often causes warping in thin plates, but the HH-LP treatment using low-energy laser pulses avoids this problem. The HH-LP treatment introduced compressive residual stresses of over 200 MPa on the heat-affected zone (HAZ) of the welded specimens. Fatigue tests under plane bending conditions revealed that the HH-LP treatment significantly improved the fatigue strength of the welded specimens, achieving a level comparable to that of the base …

Experimental And Theoretical Fracture Analysis Of Additively Manufactured Orthotropic V-Notches, Venkata Siva Sainath Bavapuram

Theses and Dissertations

This study presents a comprehensive investigation into the fracture behavior of additively manufactured orthotropic V-notched components made of Acrylonitrile Butadiene Styrene (ABS) material. The research integrates both theoretical and finite element approaches to evaluate stress intensity factors (SIFs) in Modes-I and II, which are fundamental in characterizing stress field distributions around notches under applied loading conditions. Unlike isotropic materials, where stress fields depend only on geometry of the component, the anisotropic nature of 3D-printed ABS introduces a dependency on material properties that necessitate different approaches to include anisotropy of the material.

Tensile specimens are 3D-printed with specific material orientations to …

Intelligent Turning Cyber-Physical Systems Modeling Using Sysml, Prithbey Raj Dey, David Lee Enke, Mario F. Buchely

Engineering Management and Systems Engineering Faculty Research & Creative Works

Cyber-Physical Systems (CPS) support industrial automation that incorporates people, hardware, signal, computation, and control using networking to achieve desired results. The complex automated CPS design demands a standard and comprehensive approach to appropriately identify the system requirements, define the architecture, and model the relationships among the software and hardware components. Systems Modeling Language (SysML) provides the capability for a comprehensive modeling to capture the desired design requirements in the systems architecture. SysML enables performance estimation of the model by analyzing constraints while identifying interactions among the components through various behavioral diagrams. In this paper, SysML is applied to the design …

Controlling Nitrogen Pickup During Induction Melting Of Ultrahigh-Strength Cr-Ni-Mo-V Steels, Kingsley T. Amatanweze, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field

Materials Science and Engineering Faculty Research & Creative Works

Nitrogen pickup during air induction melting can result in porosity and a loss of fracture toughness in ultrahigh-strength quenched and tempered steel castings. Nitrogen atoms are easily adsorbed into liquid steel upon exposure to the air, and argon shrouding alone has limited effectiveness. Previous studies have shown that proper charge sequencing and maintaining a high amount of dissolved oxygen in the melt prior to tapping and deoxidation can limit nitrogen pickup in the melt. In the current study, the effect of melt practice and charging procedure on nitrogen pickup was studied as a function of hold time in a series …

Parametric Analysis Of Water Jet Descaling Efficiency Of Reheated Continuously Cast Thin Slab, Tochukwu P. Ojiako, Mario F. Buchely, Simon Lekakh, Ronald J. O'Malley, Richard Osei, Taha Tayebali

Materials Science and Engineering Faculty Research & Creative Works

Efficient oxide scale removal is critical for maintaining surface quality and process efficiency in steel manufacturing. This study optimizes water jet descaling by evaluating the performance of flat and rotary jet nozzles under varying process parameters. Using a combined approach of experimental analysis and computational fluid dynamics, it investigates the influence of pressure (138–275 bar), lead angle (0°, 15°, 25°), working distance (50–100 mm), and spray angle (15°–25°) on descaling efficiency. Findings indicate that flat jet nozzles achieve superior performance at short working distances due to concentrated impact forces, while rotary jet nozzles sustain efficiency over extended distances through dynamic …

Effect Of Gating Design On Filling And Inclusion Control In An Al-Killed Cr-Mo-Ni Steel, Kingsley T. Amatanweze, Koushik Balasubramanian, Soumava Chakraborty, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field, Krista R. Limmer, Katherine M. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

The effect of gating system design on the inclusion population and size distribution in an aluminum-killed low-alloy advanced high strength steel casting was studied. A mold with four different gating systems: pressurized and non-pressurized with side risers, naturally pressurized with a side riser, and naturally pressurized with a top riser, was designed using computational fluid dynamics and solidification software. The design allowed inclusion populations in castings produced with each gating system to be compared during the same pouring event. Samples taken from different positions just below the top surface of each casting were analyzed using an SEM/EDS system with automated …

Greek Key-Inspired Fractal Metamaterials With Enhanced Flexibility And Energy Absorption., Zhennan Zhang

Electronic Theses and Dissertations

Architected materials with intricate three-dimensional (3D) geometries offer unique properties and functionalities but face challenges in manufacturing costs and complexity. This research explores the integration of simple 2D Greek Key-inspired lattices into fractal designs to achieve exceptional mechanical performance. Using 3D printing and kerfing, these fractal structures demonstrate enhanced flexibility and energy absorption capabilities. Through three-point bending and in-plane tensile tests, the 2D fractal lattices exhibited a 600-fold reduction in bending force and a tensile stretch capacity of up to 520%, significantly outperforming brittle parent materials. Out-of-plane compression tests revealed a five-fold increase in energy absorption compared to honeycomb structures, …

A Study On High-Frequency Bending Fatigue, Microhardness, Tensile Strength, And Microstructure Of Parts Made Using Atomic Diffusion Additive Manufacturing (Adam) And Additive Friction Stir Deposition (Afsd), Hamed Ghadimi

LSU Doctoral Dissertations

This dissertation reports the findings of several studies on the mechanical and microstructural properties of parts made using atomic diffusion additive manufacturing (ADAM) and additive friction stir deposition (AFSD). The design of a small-sized bending-fatigue test specimen for an ultrasonic fatigue testing system is reported in Chapter 1. The design was optimized based on the finite element analysis and analytical solution. The stress–life (S–N) curve is obtained for Inconel alloy 718. Chapter 2 presents the findings of ultrasonic bending-fatigue and tensile tests carried out on the ADAM test specimens. The S-N curves were created in the very high-cycle fatigue regime. …

Balsa Bridge, Caleb T. Lovett

All Undergraduate Projects

The problem presented throughout this report was to create a small-scale bridge made entirely out of balsa wood and glue, that could withstand substantial force, as well as perform a lifting/lowering cycle. Other requirements associated with the bridge were properties of weight, deflection, size, and shape. This problem presented a challenge that tested the mathematical side of engineering, being strongly reliant on statics, mechanics of materials, and mechanical design analyses.

To approach this problem, the first step was to complete in depth calculations of the chosen design. With this done, manufacturing and assembly was able to be completed. With a …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. The end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Impact Of Quenching Intensity Conditions On Using A Finite Element Model To Investigate The Microstructure And Hardenability Of Low-Alloy Steel, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

Quenching is one of the primary processes to improve mechanical properties in steels, particularly hardness. Quenching is well established for different geometries of individually treated steel components; while in-steam quenching of large diameter continuously cast steel bar has several specific features which are difficult and costly to experimentally optimize. the end-quench Jominy test has been used extensively to study the hardenability of different steel grades. Different numerical, analytical, and empirical models have been developed to simulate the Jominy process and to understand quenching of steels. However, it is not straight forward to translate experimental data from Jominy test on instream …

Short Strand Carbon Fiber Reinforced Polylactic Acid Filament For Additive Manufacturing, Dale Chenoweth, Lukas Seggi, Luke Phillips

Williams Honors College, Honors Research Projects

In this design project, the additive manufacturing filament of short strand carbon fiber (SSCF) reinforced polylactic acid (PLA) composite was developed. The micro-size, precision cut SSCFs were mixed with the PLA pellets through a melting homogenization process. Through this process the composite material block is cut and divided into pieces for ease of pelletizing. The material block pieces are then pelletized to be fed through the single screw extruder to develop the SSCF-PLA composite filament. The SSCF-PLA filaments were manufactured with a varying amount of SSCF ranging from 0.5% to 10% of the material block's weight. Development of a 1% …

Implementation Of Experimental Static Recrystallization Of High Strength Steel Into Computational Simulation Of Multi-Pass Slab Hot Rolling, S. K. Dasari, S. Ganguly, A. Abutunis, K. Chandrashekhara, M. F. Buchely, S. N. Lekakh, R. J. O'Malley, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural changes and softening due to static recrystallization have a critical influence on thermo-mechanical behavior of high strength steels during industrial multi-pass hot rolling. Numerical simulation using finite element analysis (FEA) can be used to accurately predict the softening behavior during the hot rolling process. Therefore, the implementation of an experimentally defined static recrystallization model into FEA is necessary to get realistic simulation prediction. in this study, the extent of softening during static recrystallization in Si and Mn alloyed high strength steel was measured using double hit tests. a Gleeble™ thermo-mechanical simulator was used to perform the double hit tests …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario Buchely, Ronald O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the face-centered cubic (FCC) multi-principal element alloys (MPEAs) developed thus far contain cobalt. for many applications, it is either required or beneficial to avoid cobalt, since cobalt has long-term activation issue (for nuclear applications), is expensive, and is considered a critical material. in addition, FCC structured solid-solution MPEAs tend to have relatively low strength. an FCC solid-solution Fe30Ni30Mn30Cr10 (at %) MPEA was fabricated via arc melting, followed by homogenization at 1100 °C for 12 h. the alloy was hot rolled at 1100 °C with a total reduction of up to 97 %. the microstructure was characterized, and mechanical …

A High-Strength Precipitation Hardened Cobalt-Free High-Entropy Alloy, Matthew Luebbe, Jiaqi Duan, Fan Zhang, Jonathan Poplawsky, Hans Pommeranke, Maalavan Arivu, Andrew Hoffman, Mario Buchely, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. a Co-free (Fe0.3Ni0.3Mn0.3Cr0.1)88Ti4Al8 HEA was developed and studied in this work. in contrast to previous Co-free HEAs, this alloy is close to Equi atomic in its composition and promises a more …

Rc Baja Suspension And Steering, Garrett Bailey

All Undergraduate Projects

The RC Baja team set out to engineer and construct a working remote-control device that can compete in the ASME Baja Competition. The students have a focus on either suspension and steering or drivetrain and chassis. This report is centered on the suspension and steering. First, multiple analyses were completed using engineering methods such as mechanical design, statics, strengths of materials, and dynamics for parts of the device. The calculations found in the analysis are then used to create designs for the parts so that they will meet the requirements and be successful in the competition. After the parts are …

Adjust-A-Ramp, Taylor Sharrits, Courtney Banks, Emily Beck, Jazmin Buenrostro

Williams Honors College, Honors Research Projects

Adjust-A-Ramp is a portable ramp designed to ensure the safety of consumers and prevention of damage to cars, specifically towards low profile cars. A low-profile vehicle includes any vehicle that has a clearance off the ground of 6.5 inches or less. Advantages of low-profile vehicles include improved handling, better braking, increased fuel efficiency, increased stability, and an overall luxury aesthetic. The reduced tire size increases grip on smooth surfaces with better wheel response, creating a fast, more efficient ride. The simple tire tread patterns and the stiff sidewalls allow for lower rolling resistance which increases fuel economy. The Adjust-A-Ramp can …

Grinding And Super-Finishing Test Machine Project, Michael Simon

Williams Honors College, Honors Research Projects

A research project in The University of Akron to study grinding and super-finishing of silicon nitride ceramic was initiated by Dr. Siamak Farhad and sponsored by the Timken Company, with the assistance of undergraduate students Michael Simon, Ryan Hosso and Mathew Rozmajzl. The study required analysis of forces and scratches generated during grinding processes of silicon nitride samples. A testing assembly was designed and constructed to record the forces generated during grinding and super-finishing of silicon nitride samples in a computer-numerical-control machine. Silicon nitride samples were subjected to desired grinding and super-finishing operations and all forces generated during the process …

Mini Rc Baja Car, Jason Schindler

All Undergraduate Projects

Incorporating each aspect of engineering incorporated into a senior project is difficult. That is why an RC Baja car is a great senior project for Mechanical Engineering students. The approach that students must take to design, construct, and test the car is to set parameters, and to make overall goals that can be easily measured. These goals include, but not limited to things like a $700 budget and the ability to withstand a 1-foot drop to a flat surface on all four wheels simultaneously. First, the design must meet the specifications and rules that are set previously. This ensures that …

Hydraulic Balsa Wood Rising Bridge, Kaitlyn Greenfield

All Undergraduate Projects

What is the solution to allowing tall vessels to navigate past a vehicle bridge that is less than 10 [ft] above the water? To answer this question, a balsa wood bridge was designed, constructed, and tested. The bridge needed to articulate by mechanical means, allow for travel through the bridge, and be able to withstand ample force while the main structure only being constructed of balsa wood and glue. The project was analyzed in sections. These sections include: the bridge structure and its members, the hydraulic lift, and the pins needed for the bridge and hydraulic lift to operate. The …

Entertainment 721, Mark Hendricks, Noah John, Jadon Vanyo, Chelsea Payne

Williams Honors College, Honors Research Projects

The goal of this project was to design a luxury, aesthetically pleasing entertainment system with a TV lift mechanism that could be remote controlled. The design would also include a cooling cabinet for gaming systems, a remote locking system, and additional storage. Using a morphological chart and weighted decision matrix for each subsystem key features were determined to be included in the design. Several performance benchmarks were determined to accomplish the team’s design. Almost every benchmark was successful in the build of the first prototype. Several heat calculations and FEA analyses were performed on the system to ensure the success …