Dynamics and Dynamical Systems Commons^™

Integrating Gis With Interim Payment Valuation In Road Construction Projects: A Conceptual Framework, Abdulrahman I. Iro, Juma M. Matindana, Julian Ijumulana

Tanzania Journal of Engineering and Technology (TJET)

Abstract

Interim Payment Valuation is a critical process in road construction contract administration, yet conventional valuation practices remain heavily dependent on manual measurements, fragmented documentation, spreadsheets, and professional judgement. These limitations can affect measurement accuracy, transparency, traceability, and the timeliness of payment certification. Although Geographic Information Systems have increasingly been applied to construction planning, quantity measurement, progress monitoring, infrastructure management, and decision support, their integration with contractual and financial processes for interim payment valuation remains insufficiently explored. This study therefore develops a conceptual framework for integrating GIS with Interim Payment Valuation in road construction projects. A PRISMA-guided structured literature review …

Voltage-Related Power Quality Issues And Impacts On Distribution Networks With Sensitive Loads - A Review, Godwin Elinazi Mnkeni, Jackson Justo, Aviti Thadei Mushi, Bakari M. M. Mwinyiwiwa

Tanzania Journal of Engineering and Technology (TJET)

Voltage disturbances are the most important power quality (PQ) complications that customers and power utilities face in this smart era. The growing adoption of sophisticated electronic equipment and integration of renewable energy sources (RES) into power grids has increased the susceptibility of power distribution networks (PDNs) to voltage sags, swells, interruptions, flicker, and voltage imbalance. These disturbances, mainly caused by upstream faults, switching operations, and RES integration, compromise voltage PQ and system reliability. Consequently, they accelerate equipment degradation, increase electronic waste (e-waste), raise reactive power demand and maintenance costs, increase power losses, and impose substantial economic losses on customers and …

An Analytical Framework For Quantifying Urban And Community Resilience To Natural Hazards From Cell-Phone Gps-Location And Traffic-Flow Data, Georgios Chatzikyriakidis

Civil and Environmental Engineering Theses and Dissertations

Urban areas are increasingly exposed to natural hazards while accommodating a growing share of the global population, yet a consistent science-based framework for quantifying urban and community resilience remains lacking. This dissertation develops a physics-based analytical framework grounded in statistical mechanics and the quantitative theory of Brownian motion. A city is conceptualized as a complex medium in which citizens move analogously to Brownian particles within a viscoelastic environment, influenced by socioeconomic interactions and infrastructure functionality.

A central premise is that urban resilience, interpreted as engineering resilience (an outcome), can be quantified through a single metric: the mean-square displacement MSD=⟨r²(t)⟩, of …

Analysis Of Factors Enabling Organisational Governance Maturity For The Technical Audit Function In Tanzania, George C. Haule

Tanzania Journal of Engineering and Technology (TJET)

The study aimed to identify key factors contributing to Organisational Governance Maturity (OGM) of the Technical Audit Functions (TAF) in Tanzania.  The study employed a sequential approach as a research design.  The first step was to collect and analyse literature studies to identify factors enabling the OGM of the TAF.  Next, a questionnaire was administered to one hundred twenty-eight (128) respondents from seven (7) TAFs to rank the key enabling factors that were identified from the literature that influence the OGM of TAF in Tanzania.  Using data from a questionnaire administered to 128 respondents, a two-step strategy was employed to …

Ai-Scm Cmm: A Capability Maturity Model For Artificial Intelligence Integration In Supply Chain Management, Lordt Becklines, Omar F. El-Gayar, Patti Brooks, Insu Park

Annual Research Symposium

Artificial intelligence is increasingly deployed in supply chain management, yet many organizations struggle to align adoption efforts with process readiness, data quality, governance, and workforce capabilities, and they still lack validated supply chain specific roadmap for assessing readiness, sequencing investments, and reducing implementation risk. This study develops and evaluates a Capability Maturity Model for Artificial Intelligence Integration in Supply Chain Management to address that gap. Using a design science research approach, the study synthesizes prior literature and practitioner knowledge to define maturity dimensions, capability indicators, and staged progression levels for AI integration in supply chain contexts. The artifact and assessment …

Towards Metrology 4.0 In Developing Countries’ Manufacturing Industries, Jailos Nzumile

Tanzania Journal of Engineering and Technology (TJET)

A systematic literature review was conducted to unveil the status of the digital transformation of metrology in developing countries, as they are lagging in utilising fourth industrial revolution (IR4.0) technologies to transform manufacturing industries. A PRISMA technique was employed using various keywords to identify, screen, and select the relevant literature. Forty publications were selected for the review, mainly discussing IR 4.0 technologies in metrological operations. The results indicate that the digital transformation of metrology has yet to be initiated in developing countries. However, the employment of IR4.0 technologies in advancing metrological operations in manufacturing industries is mostly discussed in the …

Potential Use Of Pump As Turbine Coupled To Self-Excited Induction Generator For Micro-Hydro Cooking And Cooling Applications, Emanuel J. Nyirenda

Tanzania Journal of Engineering and Technology (TJET)

Clean cooking and efficient cooling in developing countries have recently become areas of great focus. Further, the environmental impact of flooding in high-capacity hydroelectric plants has become a major concern. As a result, there is growing emphasis on developing sustainable and decentralized energy solutions, focusing on the potential of micro-hydro systems, especially in rural and remote areas. Although there are several alternative energy generation methods, their application is not straightforward. One of the latest technologies under research is using pumps as turbines coupled to an induction generator. This paper explores through a rigorous experimental approach the possibility of using a …

Modeling Of Carbonization And Absorption Processes In Soda Ash Production, Nadirbek Rustambekovich Yusupbekov, Djalolitdin Paxritdinovich Mukhitdinov, Fatima Faxritdinovna Iskhakova

Chemical Technology, Control and Management

The article considers the problem of modeling the ammonia-soda process of soda ash production and presents the chemistry of sodium bicarbonate (NaHCO₃) formation. The equation of the kinetics of the reaction, used as a model of the carbonation process, is derived from a system of equations and its computer model is compiled. The system of differential equations reflecting the kinetics of the process was solved in the Mathcad package. The result of the modeling is presented. Based on the experimental data, the dependence of the absorption column performance on temperature and the dependence reflecting the optimal value of the absorption …

Algorithms For Making Control Systems Based On Neural Network Technology To Automate Dynamic Plants, Jasur Sevinov, Abdishukurov Maqsudovich Shavkat

Chemical Technology, Control and Management

This paper examines the stages of multilayer neural network technology for the control and identification of dynamic systems. It is seen many ways to use multilayer neural networks in control systems. Neural controllers are based on several models and algorithms. Examples of such algorithms include the predictive model-based control algorithm, the Narma-L2 control algorithm, and the benchmark model-based control algorithm. These controllers illustrate various general ways to use multilayer neural networks in control systems. Common, standard linear control architectures have been proposed for many neural controllers.

Microwave Ore Pre-Treatment Review And Process Flowsheet Conceptualization, Baker F. Giyani

Tanzania Journal of Engineering and Technology (TJET)

The global demand for mineral commodities has increased dramatically over the years, and this is largely due to several factors, including technological advancements, industrialization, and a rise in population. Further, the demand keeps increasing because the ore being mined is becoming more complex, and the feed grade is declining over the years, prompting the need for innovative technologies to treat such ores more efficiently. Microwave ore pre-treatment is one of the potential technologies that can be employed to improve process performance. This is possible because ores are composed of both good-microwave heaters and poor microwave heaters, which creates thermal stresses …

Application Of Artificial Neural Network Models For Predicting Diesel And Petrol Prices In The Geographically Sparsed Regions In Tanzania, John M. Kafuku

Tanzania Journal of Engineering and Technology (TJET)

Fuel consumption in Tanzania, mainly diesel and petrol, accounts for 82 percent of the energy consumption in the country, with significant price volatility affecting market stability, availability of fuel, and investment decisions. This study uses an artificial neural network (ANN) with a backpropagating algorithm to predict fuel prices in four regions of Tanzania. Key input parameters include the currency inflation rate (CIR), the petrol fuel inventory (PFI), the diesel fuel inventory (DFI), and the fuel transport costs (FTC). The study selected the 6-10-10-2 ANN structures for Sumbawanga-Rukwa, Mpanda-Katavi, and Mbeya-Mbeya as well as 6-10-9-2 for the Songea-Ruvuma region. The results …

Heavy Metals Pollution In Roadside Ecosystems, Lilian Matafu

Tanzania Journal of Engineering and Technology (TJET)

Heavy metals refer to metallic elements that are characterized by having a relatively high density and they are toxic or poisonous even at low concentration. They are environmental pollutant owing to toxicity and longevity in atmosphere and ability to accumulate in living things via bioaccumulation. They tend to enter in different system such as food chain. Analyses of water, soil sediment and the surrounding growing plants (Cynodon dactylon and Cyperus species) for selected heavy metals (Cd, Pb, Zn and Cu) were conducted on a roadside pond located at Boko MSB, Dar es Salaam. Pond water, soil sediments and plant samples …

Assessment Of Wind Speed Characteristics And Available Wind Power Potential For Electricity Generation In Tanzania, Mwingereza John Kumwenda

Tanzania Journal of Engineering and Technology (TJET)

The energy demand and its associated crises are attracting significant attention due to population increase and economic growth especially in developing countries. Fossil fuel-based energy source stand as a prominent anthropogenic resource but they are accompanied with increased carbon emissions and heightened environmental concerns. Renewable energy sources such as wind energy can offers a lot of potential for sustainable growth in the energy sector of developing nations like Tanzania. Thus, this work investigated wind speed characteristics and available wind power potential in six selected regions in Tanzania with different topographical features for future electricity generation. The data of the wind …

Capacitive Sensors With Ultra-Small Capacitance For Smart Measurement And Control Systems, Rustam Baratov, Farrux Jabbor O'G'Li Ko'charov

Chemical Technology, Control and Management

This article discusses methods of low capacitance measurement of capacitive sensors. The results of the study of the amplitude-frequency (AF) and phase-frequency (PF) response of measurement circuits of capacitive sensors for low capacitances measurement, consisting of RC - differentiating elements are presented. The input and output parameters of the differentiating circuit and the complex transfer function are analyzed. The research results show that low capacitances measurement by measuring the rectangular pulses duration is the most effective measurement method.

Development And Testing Of Small-Scale Flash Dryer For Maize Bran, Eden Ngowi

Tanzania Journal of Engineering and Technology (TJET)

Sun drying is the most common technique used to dry various food products due to its economic convenience. However, it is not effective owing to its unreliable nature leading to microbial deterioration and aflatoxin contamination of food. In Tanzania, about 1.3 million tonnes of maize bran are at risk of deterioration annually due to improper drying. The aim of this study was to design, fabricate and test an efficient small-scale flash dryer for maize bran. Using principles of material and energy balance, a small-scale flash dryer with a throughput of 500 kg of dry product per hour was designed resulting …

Lean Manufacturing Practices In Tanzania: Exploring Awareness, Training And Capital Investment, Francis D. Sinkamba

Tanzania Journal of Engineering and Technology (TJET)

With the growing competition among industries in the world, manufacturing industries are now forced to adopt the Lean Manufacturing philosophy to improve their competitive abilities. The adoption of the philosophy is very low in developing countries such as Tanzania, as is demonstrated with 1% of publications and the lack of knowledge and capital for Lean Manufacturing implementation causes this. Furthermore, the contribution of the sector to the Gross Domestic Product in Tanzania is low and stands at 8.4%. The study wants to bridge the gap in training, capital and awareness of Lean Manufacturing in Tanzania. Survey and purposive sampling techniques …

Assessment Of The Factors Affecting The National Ict Broadband Backbone (Nictbb) Systems Restoration Time, Victoria Mahabi

Tanzania Journal of Engineering and Technology (TJET)

This study investigates the factors affecting the prolonged system restoration time when national ICT broadband backbone (NICTBB) services are affected by breakdown incidents. NICTBB is the government-owned backbone infrastructure constructed nationally by the Republic of Tanzania to increase the usage of ICT for equitable and sustainable socio-economic development and accelerate poverty reduction. This study utilised a mixture of exploratory and descriptive study approaches. The sample size determination was executed using purposing and simple random sampling, thus involving 289 respondents. The data reliability test was undertaken. It was followed by factor analysis, analysis of variances (ANOVA), linear regression analysis, and confirmed …

Perona-Malik Diffusion-Driven Regularization For Image Resolution Enhancement In Electrical Capacitance Tomography, Nassor Ally

Tanzania Journal of Engineering and Technology (TJET)

Electrical Capacitance Tomography (ECT) is a non-invasive promising method for monitoring industrial processes, such as oil-gas flow in pipelines and solid-gas flow in pneumatic systems. Despite its potential benefits, ECT generates poor-quality images, often used only for qualitative analysis. A non-linear relationship between measured capacitances and permittivity distribution and the ill-posedness of the sensitivity matrix elements causes this limitation. This hinders the applicability of ECT in monitoring online industrial process applications. This work proposes a reconstruction method based on a nonlinear diffusion function to generate high-quality images from the measured capacitance data from the ECT system. The diffusion regularization functional …

Causes And Consequences Of Inefficient Drilling And Blasting In Mine Development Headings: A Case Study Of Hard Rock Gold Mining Operations In Northern Tanzania, George Bennett

Tanzania Journal of Engineering and Technology (TJET)

Despite the introduction of the perimeter blasting technique at the Tulawaka Gold Mine, the mine continued to suffer from an overbreak of mine development headings, with an average overbreak of 24% every 22 m, which is approximately twice the acceptable 10% overbreak. The causes of this problem include ineffective drilling practices and uneven and excessive charging of explosives, resulting in a slightly high powder factor of 3.94 kg/m3 instead of 3.8 kg/m3, as per the design. The problem of overbreak resulted in ore dilution, a longer mine development cycle time and additional costs of approximately US$ 45 per cut, especially …

Production Of Biofertilizer From Fruit And Garden Waste, Neema Msuya

Tanzania Journal of Engineering and Technology (TJET)

The project focused on the production of bio-fertilizer from fruit and garden waste, with a specific emphasis on utilizing pineapple tops in the composting process. The objective was to produce and assess the properties of the bio fertilizer obtained from this process and evaluate its potential application in agriculture. In this study, the composting process was done in a 0.7 m long, 0.85 wide and 1.1 m high vessel, and 0.238 m3 pineapple top wastes, resulting in 0.35 m3 of biofertilizer. The bio fertilizer produced exhibited favorable characteristics, including a moisture content of 36%, pH of 7.1, and a total …

Assessment Of Risk Factors Related To Body Pain Complaints In Tanzania Construction Industry, Fatma K. Mohamed

Tanzania Journal of Engineering and Technology (TJET)

The construction industry is associated with risks that can result in musculoskeletal diseases. Although young male workers who are presumed to be healthy dominate the industry in Tanzania, body pain complaints have been widely reported. The aim of this study is to assess the prevalence and causes of body pains in workers. A cross-sectional study involving 396 workers was conducted. A chi square test was used for testing association of independent categorical variables and binary logistic regression analysis was used to determine predictors for body pain complaints. The results show that all study participants complained of at least one form …

Comparison Of Meteorological Drought Indices In Tanzania Using The Meteorological Drought Monitoring Software Package, Paul Ts Limbu

Tanzania Journal of Engineering and Technology (TJET)

Low precipitation, substantial evaporation, and an unequal distribution of precipitation throughout the area are the characteristics of drought, a climatic abnormality. This study used the Meteorological Drought Monitoring (MDM) software and monthly rainfall data from the Tanzania Meteorological Authority (TMA) to examine and compare the Deciles Index (DI), Standardised Precipitation Index (SPI), Percent of Normal Index (PNI), Rainfall Anomaly Index (RAI), Z-Score Index (ZSI), China-Z Index (CZI), and Modified China-Z Index (MCZI) for drought monitoring in Tanzania from 1988 to 2017. It was found that ZSI represented the dry years better than other indices, followed by DI, RAI, PNI, SPI, …

Grinding And Super-Finishing Test Machine Project, Michael Simon

Williams Honors College, Honors Research Projects

A research project in The University of Akron to study grinding and super-finishing of silicon nitride ceramic was initiated by Dr. Siamak Farhad and sponsored by the Timken Company, with the assistance of undergraduate students Michael Simon, Ryan Hosso and Mathew Rozmajzl. The study required analysis of forces and scratches generated during grinding processes of silicon nitride samples. A testing assembly was designed and constructed to record the forces generated during grinding and super-finishing of silicon nitride samples in a computer-numerical-control machine. Silicon nitride samples were subjected to desired grinding and super-finishing operations and all forces generated during the process …

Quality Assurance Of Lightweight Structures Via Phase-Based Motion Estimation, Ikenna E. Ifekaonwu

College of Graduate Studies: Theses & Dissertations

In recent years, lightweight structures have become mature and adopted in various applications. The importance of quality assurance cannot be overemphasized hence extensive research has been conducted to assess the quality of lightweight structures. This study investigates a novel process that exploits motion magnification to investigate the damage characteristics of lightweight mission-critical parts. The goal is to assure the structural integrity of 3D printed structures and composite structures by determining the inherent defects present in the part by exploiting their vibration characteristics. The minuscule vibration of the structure was recorded with the aid of a high-speed digital camera, and the …

Kinematic Analysis Of Forehand Drop Shot And Long Shot Services In Table Tennis, Ibrahim Norzuria

Student Works (2020-2029)

Table tennis is one of the most widely played sports in the world. A frequent hand movement is compulsory to execute stroke than other limbs, especially the projection of racket and ball speeds,which can help to improve players’ performance. Until now, research on table tennis serving is limited. Service was assumed important in table tennis because the effective serve may allow the serving player to have advantage and control over the game. The 3D dynamic analysis is the appropriate method to analyze a sport activity such as table tennis. Therefore, the aim of research was to determine the kinematic involved …

Dual-Axis Solar Tracker, Bryan Kennedy

All Undergraduate Projects

Renewable energies, and fuels that are not fossil fuel-based, are one of the prolific topics of debate in modern society. With climate change now becoming a primary focus for scientists and innovators of today, one of the areas for the largest amount of potential and growth is that of the capturing and utilization of Solar Energy. This method involves using a mechanical system to track the progression of the sun as it traverses the sky throughout the day. A dual-axis solar tracker such as the one designed and built for this project, can follow the sun both azimuthally and in …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Landing-Gear Impact Response: A Non-Linear Finite Element Approach, Tuan H. Tran

UNF Graduate Theses and Dissertations

The primary objective of this research is to formulate a methodology of assessing the maximum impact loading condition that will incur onto an aircraft’s landing gear system via Finite Element Analysis (FEA) and appropriately determining its corresponding structural and impact responses to minimize potential design failures during hard landing (abnormal impact) and shock absorption testing. Both static and dynamic loading condition were closely analyzed, compared, and derived through the Federal Aviation Administration’s (FAA) airworthiness regulations and empirical testing data.

In this research, a nonlinear transient dynamic analysis is developed and established via NASTRAN advanced nonlinear finite element model (FEM) to …

Built-In Bicycle Rack For Cars, Scott A. Hansberry

All Undergraduate Projects

Transporting a bicycle after riding somewhere and then needing to be pickup can be problematic. Bicycles will not fit in most vehicles without removing components. There is also the risk of damaging the inside of the vehicle. Expecting everyone to have a bike rack for their vehicle is unrealistic because the bike rack could be considered unappealing visually, take up to much space in the trunk, or limit the vehicle owner’s access to the trunk. The solution to this problem is a bike rack that mounts onto your car and then mounts your bike onto the rack. Most people don’t …

The Pneumatic Leg Extension, David G. Sedano

All Undergraduate Projects

In recent years, reaching altitudes that are higher than your normal-height has evolved from pure amusement to an “in-demand” necessity out in the field. Means of achieving greater than normal height range from wooden poles to aluminum stilts. The era of ladders and other extension methods are slowly fading away. There are many designs in the market that focus on different factors to make a stilt. As other designs focus on one or two enhancements, the pneumatic leg extension’s objective is to improve all aspects of the stilt. This radical new design differs greatly from traditional stilt designs. The pneumatic …