Engineering Science and Materials Commons^™

The Development Of A Viscoelastic Ellipsoidal Model For Use In Measuring Plantar Tissue Material Properties During Walking, Jessica Lee Deberardinis

UNLV Theses, Dissertations, Professional Papers, and Capstones

Introduction: The mechanical characteristics of the plantar tissues during walking is not well understood as most of the current research focuses on testing specific plantar regions in cadavers or while the feet of the participants are raised. In this work, it is hypothesized that a viscoelastic geometric ellipsoid model used to assess multiple structures of the foot would be accurate and robust. This model would be participant-specific and applicable to the entire stance phase of gait.

Methods: The proposed viscoelastic ellipsoid model would represent several key anatomical areas: Heel, Posterior Midfoot, Anterior Midfoot, Metatarsals 1-2, Metatarsals 3-5, Toe 1, Toe …

Influence Of Metal Additives On Microstructure And Properties Of Amorphous Metal–Sioc Composites, Kaisheng Ming, Qing Su, Chao Gu, Dongyue Xie, Yongqiang Wang, Michael Nastasi, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Strong, ductile, and irradiation-tolerant structural materials are in urgent demand for improving the safety and efficiency of advanced nuclear reactors. Amorphous ceramics could be promising candidates for high irradiation tolerance due to thermal stability and lack of crystal defects. However, they are very brittle due to plastic flow instability. Here, we realized enhanced plasticity of amorphous ceramics through compositional and microstructural engineering. Two metal–amorphous ceramic composites, Fe-SiOC and Cu-SiOC, were fabricated by magnetron sputtering. Iron atoms are preferred to form uniformly distributed nano-sized Fe-rich amorphous clusters, while copper atoms grow non-uniformly distributed nano-crystalline Cu particles. The Fe-SiOC composite exhibits high …

Mechanical And Tribological Behaviour Of Treated And Untreated Moringa Oleifera Pods Fiber Reinforced Epoxy Polymer Composite For Packaging Applications, Prakash Sampath, Senthil Kumar V.S Dr

Journal of Applied Packaging Research

Researchers now focus on the use of natural fiber polymer composites materials for packing applications. This attention is due to their low cost and renewable characteristics. Fabrication of composites with the use of renewable resources has many benefits of alternating from an appropriate management and reduction in industrial wastages, ecofriendly behaviour to cost effectiveness. The artificial fibers in packing industries can be replaced by natural fibers in the areas where stiffness and high strength are not the primary requirement. In the last decade the use of Natural fibers in the place of artificial fibers for reinforcements in epoxy resin matrix …

Biomechanical Foot Guidance Linkage, Carl Nelson, Cale J. Stolle, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

A gait replication apparatus can include a scalable mechanical mechanism configured to replicate different gaits . The scalable mechanical mechanism can include , for example , a four - bar linkage , a pantograph , a cam / Scotch - yoke mechanism , and so forth . In some embodiments , the mechanical mechanism includes a beam rotating about an axis passing proximate to its center , with a foot pedal slidably coupled with the beam , and a timing chain / belt or cable pulley - pair coupled with the foot pedal and looped about the beam . A …

A Discrete Curvature Estimation Based Low-Distortion Adaptive Savitzky-Golay Filter For Ecg Denoising, Hui Huang, Shiyan Hu, Ye Sun

Department of Mechanical and Aerospace Engineering Publications

Electrocardiogram (ECG) sensing is an important application for the diagnosis of cardiovascular diseases. Recently, driven by the emerging technology of wearable electronics, massive wearable ECG sensors are developed, which however brings additional sources of noise contamination on ECG signals from these wearable ECG sensors. In this paper, we propose a new low-distortion adaptive Savitzky-Golay (LDASG) filtering method for ECG denoising based on discrete curvature estimation, which demonstrates better performance than the state of the art of ECG denoising. The standard Savitzky-Golay (SG) filter has a remarkable performance of data smoothing. However, it lacks adaptability to signal variations and thus often …

A Novel Correlation Model For Horizontal Axis Wind Turbines Operating At High-Interference Flow Regimes, Anurag Rajan, Fernando L. Ponta

Department of Mechanical and Aerospace Engineering Publications

Driven by economics-of-scale factors, wind-turbine rotor sizes have increased formidably in recent years. Larger rotors with lighter blades of increased flexibility will experiment substantially higher levels of deformation. Future turbines will also incorporate advanced control strategies to widen the range of wind velocities over which energy is captured. These factors will extend turbine operational regimes, including flow states with high interference factors. In this paper we derive a new empirical relation to both improve and extend the range of Blade Element Momentum (BEM) models, when applied to high interference-factor regimes. In most BEM models, these flow regimes are modeled using …

Application Of Computational Tools To Spaghetti-Based Truss Bridge Design, Jin Xu, Jiliang Li, Nuri Zeytinoglu, Jinyuan Zhai

ASEE IL-IN Section Conference

Application of Computational Tools to Spaghetti-Based Truss Design

Statics and Strength of Materials are two foundational courses for Mechanical/Civil Engineering. In order to assist students in better understanding and applying concepts to a meaningful design task, SolidWorks and theoretical calculation were used for a spaghetti-bridge design contest with the constraints of given maximum weight and allowable support-material weight. As the first step of this iterative designing process, both extrude feature and structural member were introduced to model planar bridge trusses. Then SolidWorks’ Statics module was used to run FEA analysis of the structural performance in efforts to optimize the …

Soft , Multilayered Electronics For Wearable Devices And Methods To Produce The Same, Carmel Majidi, Michael D. Bartlett, Eric J. Markvicka

Department of Mechanical and Materials Engineering: Faculty Publications

Disclosed herein is an efficient fabrication approach to create highly customizable wearable electronics through rapid laser machining and adhesion - controlled soft materials assembly . Well - aligned , multi - layered materials can be created from 2D and 3D elements that stretch and bend while seamlessly integrating with rigid components such as micro chip integrated circuits ( IC ) , discrete electrical components , and interconnects . These techniques are applied using commercially available materials . These materials and methods enable custom wearable electronics while offering versatility in design and functionality for a variety of bio - monitor ing …

Gastrointestinal Sensor Implantation System, Benjamin Terry, Weston Lewis, Wanchuan Xie, Pengbo Li, Alfred Tsubaki

Department of Mechanical and Materials Engineering: Faculty Publications

A gastrointestinal ( GI ) sensor deployment device is dis closed . In implementations , the sensor deployment device includes an orally - administrable capsule with a tissue cap ture device removably coupled to the orally - administrable capsule . The tissue capture device includes a plurality of fasteners for connecting the tissue capture device to GI tissue within a body . A biometric sensor is coupled to the tissue capture device for continuous or periodic monitoring of the GI tract of the body at the GI tissue attachment location . A chamber within the orally - administrable capsule is …

Me-Em Enewsbrief, March 2019, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Interactions Between Dislocations And Three-Dimensional Annealing Twins In Face Centered Cubic Metals, Yanxiang Liang, Xiaofang Yang, Mingyu Gong, Guisen Liu, Qing Liu, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Annealing twins often form in metals with a face centered cubic structure during thermal and mechanical processing. Here, we conducted molecular dynamic (MD) simulations for copper and aluminum to study the interaction processes between {1 1 1}1/2 <1 1 0> dislocations and a three-dimensional annealing twin. Twin boundaries are characterized with Σ3{1 1 1} coherent twin boundaries (CTBs) and Σ3{1 1 2} incoherent twin boundaries (ITBs). MD results revealed that dislocation-ITB interactions affect slip transmission for a dislocation crossing CTBs, facilitating the nucleation of Lomer dislocation.

A Hamiltonian Surface-Shaping Approach For Control System Analysis And The Design Of Nonlinear Wave Energy Converters, Shadi Darani, Ossama Abdelkhalik, Rush D. Robinett Iii, David Wilson

Department of Mechanical and Aerospace Engineering Publications

The dynamic model of Wave Energy Converters (WECs) may have nonlinearities due to several reasons such as a nonuniform buoy shape and/or nonlinear power takeoff units. This paper presents the Hamiltonian Surface-Shaping (HSS) approach as a tool for the analysis and design of nonlinear control of WECs. The Hamiltonian represents the stored energy in the system and can be constructed as a function of the WEC’s system states, its position, and velocity. The Hamiltonian surface is defined by the energy storage, while the system trajectories are constrained to this surface and determined by the power flows of the applied non-conservative …

Optimal Control Of Wave Energy Converters, Ossama Abdelkhalik, Rush D. Robinett Iii, Shangyan Zou, Giorgio Bacelli, David G. Wilson, Umesh Korde

Michigan Tech Patents

A wave energy converter and method for extracting energy from water waves maximizes the energy extraction per cycle by estimating an excitation force of heave wave motion on the buoy, computing a control force from the estimated excitation force using a dynamic model, and applying the computed control force to the buoy to extract energy from the heave wave motion. Analysis and numerical simulations demonstrate that the optimal control of a heave wave energy converter is, in general, in the form of a bang-singular-bang control; in which the optimal control at a given time can be either in the singular …

Deep Learning Segmentation Of Coronary Calcified Plaque From Intravascular Optical Coherence Tomography (Ivoct) Images With Application To Finite Element Modeling Of Stent Deployment, Yazan Gharaibeh, Pengfei Dong, David Prabhu, Chaitanya Kolluru, Juhwan Lee, Vlad Zimin, Hozhabr Mozafari, Hiram Bizzera, Linxia Gu, David Wilson

Department of Mechanical and Materials Engineering: Faculty Publications

Because coronary artery calcified plaques can hinder or eliminate stent deployment, interventional cardiologists need a better way to plan interventions, which might include one of the many methods for calcification modification (e.g., atherectomy). We are imaging calcifications with intravascular optical coherence tomography (IVOCT), which is the lone intravascular imaging technique with the ability to image the extent of a calcification, and using results to build vessel-specific finite element models for stent deployment. We applied methods to a large set of image data (>45 lesions and > 2,600 image frames) of calcified plaques, manually segmented by experts into calcified, lumen and …

Strength And Plasticity Of Amorphous Silicon Oxycarbide, Kaisheng Ming, Chao Gu, Qing Su, Yongqiang Wang, Arezoo Zare, Don A. Lucca, Michael Nastasi, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Amorphous SiOC films were synthesized by magnetron sputtering at room temperature with/without radio frequency (RF) bias and further improved in terms of mechanical properties by ion irradiation. As-deposited SiOC films without RF bias exhibit catastrophic failure at a low stress and strain, which is ascribed to microstructural heterogeneities associated with the formation of voids during deposition, as evidenced by transmission electron microscopy. Ion irradiation unifies microstructure accompanied with eliminating the voids, resulting in a simultaneously increase in strength and plasticity (ultimate strength of 5–7 GPa and the strain to shear instability of over 20%). Homogeneous microstructures are demonstrated to ensure …

Feed Control: Composite Recycle, Rosy Perez

All Undergraduate Projects

The Boeing Company gave Central Washington University an opportunity for students to research and come up with an idea to reduce costs and landfill waste caused by the trimmings from the 777x composite wing pieces. The engineering and manufacturing for this project is about transporting composite material through to the delamination and chipper process. The delamination process uses a ram to press two claw shaped devices together that bends and deforms the material in opposite directions. The chipper process uses counter rotating saw blades spaced 1/8” apart to produce small shredded material. It is important for this newly designed feed …

Me-Em 2018-19 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Faculty Research
• Enrollment & Degrees
• Department News
• Graduates
• Faculty & Staff
• Alumni
• Donors
• Contracts & Grants
• Patents & Publications

Robotic Devicewith Compact Joint Design And Related Systems And Methods, Tom Frederick, Eric Markvicka, Shane Michael Farritor, Dmitry Oleynikov

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various robotic and/or in vivo medical devices having compact joint configurations. Other embodiments relate to various medical device components, including forearms having grasper or cautery end effectors, that can be incorporated into certain robotic and/or in vivo medical devices.

Flaw Detection With Ultrasonic Backscatter Signal Envelopes, Yongfeng Song, Christopher M. Kube, Zuoxiang Peng, Joseph A. Turner, Xiongbing Li

Department of Mechanical and Materials Engineering: Faculty Publications

Ultrasound is a prominent nondestructive testing modality for the detection, localization, and sizing of defects in engineering materials. Often, inspectors analyze ultrasonic waveforms to determine if echoes, which stem from the scattering of ultrasound from a defect, exceed a threshold value. In turn, the initial selection of the threshold value is critical. In this letter, a time-dependent threshold or upper bound for the signal envelope is developed based on the statistics governing the scattering of ultrasound from microstructure. The utility of the time-dependent threshold is demonstrated using experiments conducted on sub-wavelength artificial defects. The results are shown to enhance current …

Glocal Integrity In 420 Stainless Steel By Asynchronous Laser Processing, Michael P. Sealy, Haitham Hadidi, Cody Kanger, X. L. Yan, Bai Cui, J. A. Mcgeough

Department of Mechanical and Materials Engineering: Faculty Publications

Cold working individual layers during additive manufacturing (AM) by mechanical surface treatments, such as peening, effectively “prints” an aggregate surface integrity that is referred to as a glocal (i.e., local with global implications) integrity. Printing a complex, pre-designed glocal integrity throughout the build volume is a feasible approach to improve functional performance while mitigating distortion. However, coupling peening with AM introduces new manufacturing challenges, namely thermal cancellation, whereby heat relaxes favorable residual stresses and work hardening when printing on a peened layer. Thus, this work investigates glocal integrity formation from cyclically coupling LENS® with laser peening on 420 stainless steel.

The Role Of Low-Level Image Features In The Affective Categorization Of Rapidly Presented Scenes, L. Jack Rhodes, Matthew Rios, Jacob M. Williams, Gonzalo Quinones, Prahalada K. Rao, Vladimir Miskovic

Department of Mechanical and Materials Engineering: Faculty Publications

It remains unclear how the visual system is able to extract affective content from complex scenes even with extremely brief (< 100 millisecond) exposures. One possibility, suggested by findings in machine vision, is that low-level features such as unlocalized, two-dimensional (2-D) Fourier spectra can be diagnostic of scene content. To determine whether Fourier image amplitude carries any information about the affective quality of scenes, we first validated the existence of image category differences through a support vector machine (SVM) model that was able to discriminate our intact aversive and neutral images with ~ 70% accuracy using amplitude-only features as inputs. This model allowed us to confirm that scenes belonging to different affective categories could be mathematically distinguished on the basis of amplitude spectra alone. The next question is whether these same features are also exploited by the human visual system. Subsequently, we tested observers’ rapid classification of affective and neutral naturalistic scenes, presented briefly (~33.3 ms) and backward masked with synthetic textures. We tested categorization accuracy across three distinct experimental conditions, using: (i) original images, (ii) images having their amplitude spectra swapped within a single affective image category (e.g., an aversive image whose amplitude spectrum has been swapped with another aversive image) or (iii) images having their amplitude spectra swapped between affective categories (e.g., an aversive image containing the amplitude spectrum of a neutral image). Despite its discriminative potential, the human visual system does not seem to use Fourier amplitude differences as the chief strategy for affectively categorizing scenes at a glance. The contribution of image amplitude to affective categorization is largely dependent on interactions with the phase spectrum, although it is impossible to completely rule out a residual role for unlocalized 2-D amplitude measures.

Compliant Surgical Graspers And Methods Of Making And Using, Carl Nelson, Alan Goyzueta

Department of Mechanical and Materials Engineering: Faculty Publications

This disclosure describes compliant graspers for use in endoscopic surgeries.

Self-Powered Ghz Solution-Processed Hybrid Perovskite Photodetectors, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Organic-inorganic hybrid perovskite (OIHP) based photo-responsive devices include an OIHP active layer disposed between a cathode layer and an anode layer, and an electron extraction layer disposed between the cathode layer and the active layer. The electron extraction layer includes a layer of C₆₀ directly disposed on the active layer. The active layer includes an organometal trihalide perovskite layer (e.g., CH₃NH₃PbI₂X, where X includes at least one of Cl, Br, or I).

9r Phase Enabled Superior Radiation Stability Of Nanotwinned Cu Alloys Via In Situ Radiation At Elevated Temperature, Cuncai Fan, Dongyue Xie, Jin Li, Zhongxia Shang, Youxing Chen, Sichuang Xue, Jian Wang, Meimei Li, Anter El-Azab, Haiyan Wang, Xinghang Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

Nanotwinned metals exhibit outstanding radiation tolerance as twin boundaries effectively engage, transport and eliminate radiation-induced defects. However, radiation-induced detwinning may reduce the radiation tolerance associated with twin boundaries, especially at elevated temperatures. Here we show, via in-situ Kr ion irradiation inside a transmission electron microscope, that 3 at. % Fe in epitaxial nanotwinned Cu (Cu₉₇Fe₃) significantly improves the thermal and radiation stability of nanotwins during radiation up to 5 displacements-per-atom at 200 °C. Such enhanced stability of nanotwins is attributed to a diffuse 9R phase resulted from the dissociation of incoherent twin boundaries in nanotwinned Cu …

Relative Contributions Of Intracranial Pressure And Intraocular Pressure On Lamina Cribrosa Behavior, Junfei Tong, Deepta Ghate, Sachin Kedar, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Purpose. To characterize the relative contributions of intraocular pressure (IOP) and intracranial pressure (ICP) on lamina cribrosa (LC) behavior, specifically LC depth (LCD) and LC peak strain. Methods. An axially symmetric finite element model of the posterior eye was constructed with an elongated optic nerve and retro-orbital subarachnoid space ensheathed by pia and dura mater. -e mechanical environment in LC was evaluated with ICP ranging from 5 to 15mmHg and IOP from 10 to 45 mmHg. LCD and LC peak strains at various ICP and IOP levels were estimated using full factorial experiments. Multiple linear regression analyses were …

Design Rules For Additive Manufacturing – Understanding The Fundamental Thermal Phenomena To Reduce Scrap, M. Reza Yavari, Kevin D. Cole, Prahalada K. Rao

Department of Mechanical and Materials Engineering: Faculty Publications

The goal of this work is to predict the effect of part geometry and process parameters on the direction and magnitude of heat flow heat flux in parts made using metal additive manufacturing (AM) processes. As a step towards this goal, the objective of this paper is to develop and apply the mathematical concept of heat diffusion over graphs to approximate the heat flux in metal AM parts as a function of their geometry. This objective is consequential to overcome the poor process consistency and part quality in AM. Currently, part build failure rates in metal AM often exceed 20%, …

Resistance To Helium Bubble Formation In Amorphous Sioc/Crystalline Fe Nanocomposite, Qing Su, Tianyao Wang, Jonathan Gigax, Lin Shao, Michael Nastasi

Department of Mechanical and Materials Engineering: Faculty Publications

The management of radiation defects and insoluble He atoms represent key challenges for structural materials in existing fission reactors and advanced reactor systems. To examine how crystalline/amorphous interface, together with the amorphous constituents affects radiation tolerance and He management, we studied helium bubble formation in helium ion implanted amorphous silicon oxycarbide (SiOC) and crystalline Fe composites by transmission electron microscopy (TEM). The SiOC/Fe composites were grown via magnetron sputtering with controlled length scale on a surface oxidized Si (100) substrate. These composites were subjected to 50 keV He+ implantation with ion doses chosen to produce a 5 at% peak He …

Fast Growth Of Thin Mapbi3 Crystal Wafers On Aqueous Solution Surface For Efficient Lateral-Structure Perovskite Solar Cells, Ye Liu, Qingfeng Dong, Yanjun Fang, Yuze Lin, Yehao Deng, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Solar-grade single or multiple crystalline wafers are needed in large quantities in the solar cell industry, and are generally formed by a top-down process from crystal ingots, which causes a significant waste of materials and energy during slicing, polishing, and other processing. Here, a bottom-up technique that allows the growth of wafer-size hybrid perovskite multiple crystals directly from aqueous solution is reported. Single-crystalline hybrid perovskite wafers with centimeter size are grown at the top surface of a perovskite precursor solution. As well as saving raw materials, this method provides unprecedented advantages such as easily tunable thickness and rapid growth of …

Machine Vision Integrated Three-Dimensional Printing System, Chaiwuth Sithiwichankit

Chulalongkorn University Theses and Dissertations (Chula ETD)

Three-dimensional printing has been a widespread solution of fabricating geometrical customized products. Any 3D printed product is normally fabricated at a position defined with respect to the coordinate system of the corresponding 3D printer. So, the 3D printing cannot be conveniently implemented in some fabricating applications in which fabricating positions are commonly constrained to some physical references, e.g., architecture construction, surface restoration, food decoration, etc. This research aimed to integrate the 3D printing with machine vision, which is vastly used for guiding robotic systems to operate at desirable positions constrained to physical objects. Hence, the 3D printing can be conveniently …

Wearable Devices For Single Cell Sensing And Transfection, Lingqian Chang, Yu-Chieh Wang, Faheem Ershad, Ruiguo Yang, Cunjiang Yu, Yubo Fan

Department of Mechanical and Materials Engineering: Faculty Publications

Transdermal drug delivery systems have been successful for decades. Now these devices can be further scaled down, and their applications have been extended to wide selections of cargo, ranging from natural molecules (e.g., insulin and glucose) to bioengineered molecules (e.g., nanoparticles and vaccines). Some emerging nanopatches show promise for precise single-cell gene transfection in vivo and have advantages over conventional tools in terms of delivery efficiency, safety, and controllability of delivered dose. In this review, we discuss recent technical advances in wearable micro/nano devices with unique capabilities or potential for single-cell biosensing and transfection in the skin or other organs, …