Engineering Science and Materials Commons^™

Electrochemical Performance Of Fe3O4/C Composites As Negative Material For Lithium-Ion Batteries, Jun-Jie Cai, Shu Yao, Ze-Sheng Li, Hui Meng, Pei-Kang Shen

Journal of Electrochemistry

The Fe₃O₄/Carbon composites have been synthesized through coprecipitation pathway and by insitu aniline polymerization as a carbon source. Structural characterization and morphological study of the composites were investigated by using XRD, SEM and TEM techniques. The results showed that the nanosized Fe₃O₄ particles (40 ~ 80 nm) were encapsulated in the amorphous carbon. During the electrochemical tests, the Fe₃O₄/C composites exhibited high capaticity and excellent cycle ability, the retention of capaticity was about 1000 mAh·g^-1 after 30 cycles of charge/discharge tests at 50 mA·g^-1.

A Comparative Study Of Charge-Discharge Behaviors Of α-Pbo2 And β-Pbo2 Cathodes, Cong-Ying Cui, Xue-Mei Ma, De-Long Kong, Hou-Yi Ma

Journal of Electrochemistry

The α-PbO₂ and β-PbO₂ powders were prepared using simple chemical synthetic methods, and their crystalline structures and surface morphologies were characterized with X-ray powder diffraction spectroscopy and scanning electron microscopy. Using the as-synthesized α-PbO₂ and β-PbO₂ powders as positive active materials, the electrochemical performance of the two PbO₂ materials was investigated by means of cyclic voltammetry, galvanostatic charge-discharge tests, and electrochemical impedance spectroscopy. The results indicate that the discharge capacity of α-PbO₂ electrode is larger than that of β-PbO₂; moreover, the composite electrodes made by α-PbO₂ and β-PbO₂ mixtures with …

An In Situ Ftir Spectroelectrochemical Study On Methanol Oxidation At Pt-Mo2C/Gc Catalyst, Hai-Ping Huang, Xi-Yu Yao, Pei-Kang Shen

Journal of Electrochemistry

A 40% Pt on Mo₂C/GC catalyst has been prepared by ion exchange method. The mechanism of methanol electrooxidation on Pt-Mo₂C/GC and commercial Pt/C catalysts in acidic media was studied by cyclic voltammetry, XRD measurements and in-situ Fourier transform infrared spectroelectrochemistry. The results revealed that the Pt nanoparticles were uniformly dispersed on Mo₂C/GC with an average particle size of 3 nm. The cyclic voltammetric and chronopotentiometric experiments indicated that Pt-Mo₂C/GC catalyst exhibited a better performance for methanol oxidation than that of Pt/C in acid solution. A negative shift over 90 mV of the …

Applications Of Ellipsometry In The Investigations Of Electrode-Solution Interface, Jing-Lei Lei, Liang-Liu Wu, Ling-Jie Li, Sheng-Mao Wu, Sheng-Tao Zhang

Journal of Electrochemistry

Ellipsometry is an optical technique with high-sensitivity to quantitatively obtain surface/interface properties such as thickness andrefractive index by analyzing the changes in polarized light reflected from the surface/interface. Its noncontacting and nondestructivenature makes it possible to acquire thein situreal-time information of the change at the surface/interface. Therefore, ellipsometry has been used widely in the electrochemical investigations. In this paper, based on the brief introduction of the measurementprinciple of ellipsometry, the current progress and the future trends of ellipsometry in electrochemistry arediscussed. The applications of ellipsometry in the fields of conversion and storage of electrochemical energy, electrochemistry ofmaterials science,electroanalysisand bioelectrochemistry are …

Oxygen Reduction Reaction On Glycin Modified Pt(111) Electrode, Ming-Fang Li, Jing Kang, Ling-Wen Liao, Yan-Xia Chen, Shen Ye

Journal of Electrochemistry

O

xygen reduction reaction (ORR) on glycin (NH₂CH₂COOH) modified Pt(111) electrode has been investigated using hanging meniscus rotating disk electrode system (HMRD) in 0.05 mol•L^-1 H₂SO₄ and 0.1 mol•L^-1 HClO₄ solutions, respectively. Cyclic voltammograms of the glycin modified Pt (111) electrode measured in 0.05 mol•L^-1 H₂SO₄ solution similar to that of CN^- modified Pt(111) electrodes, demonstrating that sulfate adsorption is strongly inhibited at the glycin modified Pt(111). From the polarization curve of ORR recorded in 0.05 mol•L^-1 H₂SO₄ solution, it is …

Porous Electrodes With High Pt Utilization Obtained By Ion-Exchange/Electrodeposition, Si-Guo Chen, Wei Ding, Xue-Qiang Qi, Li Li, Zi-Hua Deng, Zi-Dong Wei

Journal of Electrochemistry

We report a novel method based on ion-exchange/electrodeposition (IEE) for constructing high Pt utilization porous electrodes. The electrode prepared using IEE was assessed by linear sweep voltammetry (LSV), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and single cell test. The preliminary results show that the undesired ion-exchange between Pt anion and surface functional group in carbon black can be eliminated through the electrode preparation process, and every Pt particle prepared by IEE is expected to be deposited on the three-phase reaction zone and thus can be fully utilized in fuel cell reactions. The Pt particle size, shape and distribution …

Effect Of Ti/Pbo2 Electrodes Doped With Different Elements On Electrocatalytic Oxidation Characteristics Of Phenol, Xiao-Lei Liu, Yuan-Yuan Dan, Hai-Yan Lu, Hai-Bo Lin, Ming-Li Ouyang, Chuan-Jun Yun

Journal of Electrochemistry

Three types of electrodes, namely, Ti/PbO₂, F-doped PbO₂ (Ti/PbO₂-F) and nano-Co₃O₄-doped PbO₂ (Ti/PbO₂+Nano-Co₃O₄) electrodes, were prepared by electro-deposition method on the Ti substrate with the interlayer of SnO₂-Sb₂O₅. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to study the compositions, structures and film morphologies of the electrodes. Electrocatalytic oxidation characteristics to phenol on the prepared electrodes were investigated by electrochemical method. The experimental results showed that compared with the Ti/PbO₂ electrode, the potentials of oxygen …

A Dft Calculation Screening Of Pt-Based Bimetallic Catalysts For Oxygen Reduction, Li-Hui Ou, Sheng-Li Chen

Journal of Electrochemistry

Developing Pt-lean catalysts for oxygen reduction reaction (ORR) is the key for large-scale application of proton exchange membrane fuel cell (PEMFC). In this paper, we have proposed a multiple-descriptor strategy for screening efficient and durable ORR alloy catalysts of low Pt content. We argue that an ideal Pt-based bimetallic alloy catalyst for ORR should possess simultaneously negative alloy formation energy, negative surface segregation energy of Pt and a lower oxygen binding ability than pure Pt. By performing detailed DFT calculations on the thermodynamics, surface chemistry and electronic properties of various Pt-M alloys (M refers to non-precious transition metals in the …

Sodium Carbonate Catalyzed Photoelectrochemical Water Splitting Over Tio2 Nanotubes Photoanode, De-Sheng Kong, Jing Wang, Xue-Di Zhang, Xi Zhao, Chao Wang, Yuan-Yuan Feng, Wen-Juan Li

Journal of Electrochemistry

Surface recombination of the photogenerated electron-hole pairs at semiconductor/electrolyte interface is one of the most essential reasons responsible for lowering photoconversion efficiency (Φ) of light to chemical energy for photoelectrochemical (PEC) water splitting reaction. In this paper, the catalytic effect of sodium carbonate on the oxygen evolution reaction (OER) over TiO₂ nanotubes photoanode during PEC water splitting was investigated by performing photocurrent and ac impedance measurements. It was demonstrated that the addiction of 1 mmol•L^-1 Na₂CO₃ in 0.5 mol•L^-1 NaClO₄ electrolyte can effectively improve the charge transfer properties for the photogenerated holes across …

Structure And Properties Of Cocoons And Silk Fibers Produced By Attacus Atlas, Narendra Reddy, Yi Zhao, Yiqi Yang

Department of Textiles, Merchandising and Fashion Design: Faculty Publications

Silk fibers in the three layers of Attacus atlas (A. atlas) cocoons have morphological structure and tensile properties similar to that of Bombyx mori silk. Attempts are being made to produce silk for commercial applications from cocoons of relatively unknown wild insects due to the unique properties of the fibers and as a source of income and employment. In this research, A. atlas cocoons were used to study the chemical composition, morphology, physical structure and tensile properties of the silk fibers in the cocoons and ability of the fibers to support the attachment and proliferation of mouse fibroblast cells. It …

Microstructure And Mechanical Properties Of Titanium Nitride Optical Coatings Made By Dc Magnetron Sputtering, Gustavo Martinez

Open Access Theses & Dissertations

Titanium nitride (TiNx) thin films were grown by DC (Direct Current) magnetron sputtering method onto Si(100) substrates by varying time of deposition to produce films with variable thickness (dTiN) in the range of 20-120 nm. The grown TiNx films were characterized by studying their structure, composition, and mechanical properties. Nuclear reaction analysis (NRA) combined with Rutherford backscattering spectrometry (RBS) analyses indicate that the grown films were stoichiometric TiN. Grazing incidence X-ray diffraction (GIXRD) measurements indicate that the texturing of the TiN films changes as a function of dTiN. The (111) and (002) peaks appear initially; with increasing dTiN, (111) becomes …

Structure And Electronic Properties Of Pure And Nitrogen Doped Nanocrystalline Tungsten Oxide Thin Films, Vemnkata Rama Sesha Ravi Kumar Vemuri

Open Access Theses & Dissertations

Tungsten oxide (WO₃) is a multifunctional material which has applications in electronics, sensors, optoelectronics, and energy-related technologies. Recently, electronic structure modification of WO₃ to design novel photocatalysts has garnered significant attention. However, a fundamental understanding of nitrogen induced changes in the structure, morphology, surface/interface chemistry, and electronic properties of WO₃ is a prerequisite to producing materials with the desired functionality and performance. Also, understanding the effect of thermodynamic and processing variables is highly desirable in order to derive the structure-property relationships in the W-O/W-O-N material system. The present work was, therefore, focused on studying the effects …

Reducing Metal Alloy Powder Costs For Use In Powder Bed Fusion Additive Manufacturing: Improving The Economics For Production, Fransisco Medina

Open Access Theses & Dissertations

Titanium and its associated alloys have been used in industry for over 50 years and have become more popular in the recent decades. Titanium has been most successful in areas where the high strength to weight ratio provides an advantage over aluminum and steels. Other advantages of titanium include biocompatibility and corrosion resistance. Electron Beam Melting (EBM) is an additive manufacturing (AM) technology that has been successfully applied in the manufacturing of titanium components for the aerospace and medical industry with equivalent or better mechanical properties as parts fabricated via more traditional casting and machining methods. As the demand for …

Crystal Structure, Phase, And Optical Properties Of Yttrium-Doped Hafnium Oxide Nanocrystalline Thin Films, Alejandro Ortega

Open Access Theses & Dissertations

Yttrium-doped hafnium oxide (YDH) nanocrystalline films were produced by sputter-deposition at various substrate times and temperatures, to produce YDH films in a wide range of thicknesses, dYDH∼25 to 1100 nm. The deposition was made onto optical grade quartz and sapphire substrates. Samples deposited on sapphire were subject to post-deposition annealing (PDA) at various times (3-24 hr) and temperatures (1100 - 1500 °C). The effect of d[special characters omitted]YDH on the crystal structure, surface/interface morphology and optical properties of YDH films was investigated. X-ray diffraction analyses revealed the formation of monoclinic phase for relatively thin films (<150nm). The evolution towards stabilized cubic phase with increasing dYDH [special characters omitted]is observed. The scanning electron microscopy results indicate the dense, columnar structure of YDH films as a function of dYDH. Spectrophotometry analyses indicate that the grown YDH films are transparent and exhibit interference fringes. The band gap was found to be ∼ 5.60 eV for monoclinic YDH films while distinct separation and an increase in band gap to 6.03 eV is evident with increasing dYDH and formation cubic YDH films. The PDA films band gaps were found to be between 5.31 and 5.72 eV, all of which exhibit secondary gaps. A correlation between growth conditions, annealing, phase evolution, and optical properties of the YDH nanocrystalline thin films is established.

Comparative Characterization Of Ni-Base Superalloys Fabricated By Laser And Electron Beam Melting Technologies, Krista Amato

Open Access Theses & Dissertations

Nickel-base superalloys have been used in cast and wrought, and powder metallurgy forms for nearly four decades for industrial and automotive applications. One drawback of cast alloys is that upon solidification, there is minimal microstructural control. Another issue to be improved is to eliminate the limitations of shapes and forms of fabricated alloys.

Rapid prototyping is a new technology of additive manufacturing that shows to be promising for the freeform fabrication of novel superalloys, including nickel-base alloys. New rapid manufacturing technologies allow us to produce parts in any shape that can be designed by computer-aided design (CAD) software. Additionally, the …

Experimental Study On The Fabrication Of Advanced Materials For Energy Applications Using High Energy Mechanical Milling, Ashvin Kumar Narayana Swamy

Open Access Theses & Dissertations

The reaction of aluminum (Al) powder with water has the potential for on demand hydrogen generation. Conventional Al powders, however, react with water slowly due to a highly protective oxide layer on the particle surface. Current methods for Al activation involve harmful and expensive materials. The nano-scale Al powders also remain very expensive and have problems such as a large amount of oxide on the surface. The use of aluminum in an energy generation cycle is also hindered by the fact that, although Al is the most abundant metal in the Earth's crust, its recovery from ore consumes a lot …

New Topics On Nanoindentation Of Polymers And Composite Materials, Ricardo Martinez-Hernandez

Open Access Theses & Dissertations

In this study, nanoindentation was used to determine Young's modulus of homogeneous plastic materials as well as inhomogeneous epoxy woven fabric composites using various indenters. In the first part, homogeneous PMMA and polycarbonate were characterized using conical and spherical indenters. The conventional approach of the inverse analysis was modified in order to account for effects obtained during spherical nanoindentation. The experimental results were verified using FEA analysis in ABAQUS. It was found that viscous effects were present in conical nanoindentations which led to an overestimation of contact stiffness. The second part, the response of carbon and glass fiber woven fabric …

Structural, Optical And Electrical Properties Of Yttrium-Doped Hafnium Oxide Nanocrystalline Thin Films, Abhilash Kongu

Open Access Theses & Dissertations

Hafnium oxide (HfO2) has emerged as the most promising high-k dielectric for Metal-Oxide-Semiconductor (MOS) devices and has been highlighted as the most suitable dielectric materials to replace silicon oxide because of its comprehensive performance. In the present research, yttrium-doped HfO2 (YDH) thin films were fabricated using RF magnetron sputter deposition onto Si (100) and quartz with a variable thickness. Cross-sectional scanning electron microscopy coupled with Filmetrics revealed that film thickness values range from 700 A° to 7500 A°. Electrical properties such as AC Resistivity and current-voltage (I-V) characteristics of YDH films were studied. YDH films that were relatively thin (<1500 A°) crystallized in monoclinic phase while thicker films crystallized in cubic phase. The band gap (Eg) of the films was calculated from the optical measurements. The band gap was found to be ∼5.60 eV for monoclinic while it is ∼6.05 eV for cubic phase of YDH films. Frequency dependence of the electrical resistivity (ρac) and the total conductivity of the films were measured. Resistivity decreased (by three orders of magnitude) with increasing frequency from 100 Hz to 1 MHz, attributed due to the hopping mechanism in YDH films. Whereas, while ρac∼1Ω-m at low frequencies (100 Hz), it decreased to ∼ 104 Ω-cm at higher frequencies (1 MHz). Aluminum (Al) metal electrodes were deposited to fabricate a thin film capacitor with YDH layer as dielectric film thereby employing Al-YDH-Si capacitor structure. The results indicate that the capacitance of the films decrease with increasing film thickness. A detailed analysis of the electrical characteristics of YDH films is presented.

Process Study And Control Of Electron Beam Melting Technology Using Infrared Thermography, Jorge Mireles

Open Access Theses & Dissertations

An IR camera was installed in an Arcam A2 system (Arcam AB, Mölndal, Sweeden) and layer-by-layer image acquisition was achieved. The camera's capability to detect manufacturing defects was evaluated by implementing computer vision techniques using LabVIEW measurement and programming software (National Instruments, Austin, TX). Thermal maps acquired by the IR camera allowed layer-by-layer part temperature to be recorded. A core objective of this research was to study the impact of processing temperature on EBM-fabricated Ti-6Al-4V parts and achieve controlled mechanical properties. In this research, build variations were achieved by modifying parameters that change processing temperature from the standard processing temperature. …

Effect Of Hafnium-Incorporation On The Microstructure And Dielectric Properties Of Cobalt Ferrite Ceramics, Stephen Josiah Wells

Open Access Theses & Dissertations

The effect of hafnium ion (Hf⁴⁺) incorporation in cobalt ferrite (CFO) was studied. Samples of Hf substituted CFO ceramic (CoFe_2-xHf_xO₄), were synthesized in the laboratory with hafnium concentrations ranging from x=0.000 to x=0.200. X-ray diffraction scans show that the Hafnium CFO crystalizes in the inverse spinel phase. Inclusion of hafnium causes lattice expansion, increasing the lattice parameter from 8.374 í? for pure CoFe2O4 to 8.391 í? for the highest concentration of hafnium tested (x=0.020). The dielectric properties of CFO are greatly enhanced by inclusion of hafnium. The enhancement is due to the …

Thermal Barrier Coatings (Tbc's) For High Heat Flux Thrust Chambers, Christopher Michael Bradley

Open Access Theses & Dissertations

The last 30 years materials engineers have been under continual pressure to develop materials with a greater temperature potential or to produce configurations that can be effectively cooled or otherwise protected at elevated temperature conditions. Turbines and thrust chambers produce some of the harshest service conditions for materials which lead to the challenges engineers face in order to increase the efficiencies of current technologies due to the energy crisis that the world is facing. The key tasks for the future of gas turbines are to increase overall efficiencies to meet energy demands of a growing world population and reduce the …

Microstructure And Properties For Titanium Aluminide Superalloy Prototypes Fabricated By Electron Beam Melting And Thermally Processed, Jennifer Hernandez

Open Access Theses & Dissertations

Gamma TiAl has been considered to be an ideal replacement for Ni-base superalloy aerospace applications, particularly in weight-critical applications. While bulk, fully dense gamma-TiAl is 50% less dense than Ni-base superalloys, it also has excellent mechanical properties at high temperature (up to ~800°C). Pre alloyed (Ti-48Al-2Cr-2Nb) powder was used to fabricate solid, fully dense (3.85 g/cm3) components and foam components with densities ranging from 0.33 g/cm³ to 0.46 g/cm³ by electron beam melting (EBM). A 10:1 blend of 2-phase TiAl (Ti-48Al-2Cr-2Nb in ^a/_o) : Inconel 625 (Ni-22Cr-6Mo-2Nb in ^a/_o) pre-alloyed powders produced …

Rbd2po4: Room Temprature Synthesis, Chemical And Structural Stablity Upon Heating, Masoud Mollaee

Open Access Theses & Dissertations

Monoclinic RbD2PO4 polycrystals were synthesized via the room temperature crystallization of RbH2PO4 dissolved in D2O. Powder x-ray diffraction (XRD) data collected at T=25 ºC indicate that this deuterated compound crystallizes in space group P21/m with unit cell parameters a=7.688í?, b=6.192í?, c=4.781í? and β=109.02°, and is isomorphic with the intermediate-temperature phase of its hydrogenated counterpart rubidium dihydrogen phosphate (RDP). We found no evidence of previously reported [Phase Transitions 80, 17 (2007)] polymorphic phase transition in rubidium dideuterium phosphate (DRDP) upon heating from room temperature to 210 ºC. All lattice parameters vary smoothly within this temperature range, demonstrating that the P21/m phase …

Electrocatalytic Oxidation Of Formic Acid On Pd/Ni Heterostructured Catalyst, Mingjun Ren, Liangliang Zou, Ju Chen, Ting Yuan, Qinghong Huang, Haifeng Zhang, Hui Yang, Songlin Feng

Journal of Electrochemistry

A Pd/Ni bimetallic nanostructured electrocatalyst was fabricated via a two-step reduction route. Owing to an epitaxial growth of Pd atoms on the surface of Ni nanoparticles, heterostructured Pd/Ni nanocomposites were formed and verified by high resolution transmission electron microscopy combined with energy-dispersion X-ray spectroscopy. X-ray diffraction confirmed that the as-prepared Pd/Ni nanocomposites possessed a single face-centered-cubic (fcc) Pd structure, probably due to a weaker diffraction intensity of metallic Ni and/or overlapping by that of Pd. The intrinsic catalytic activity on the Pd/Ni is higher than that on the Pd. Moreover, the durability of formic acid oxidation on the Pd/Ni was …

Electrochemical Performance Of Screen-Printed Composite Coatings Of Conducting Polymers And Carbon Nanotubes On Titanium Bipolar Plates In Aqueous Asymmetrical Supercapacitors, Xiaohang Zhou, George Z. Chen

Journal of Electrochemistry

Composites of conducting polymers (polypyrrole and polyaniline) with acid treated multi-walled carbon nanotubes were formulated into printable aqueous inks, with the aid of functional additives (benzethonium chloride as a surfactant with or without polyvinyl alcohol as a binder). The inks were screen-printed as fairly uniform coatings of various mass loading densities and areas (up to 75 mg cm^-2 and 100 cm²) on thin titanium plates (0.1 mm in thickness). These screen-printed plates were used to fabricate both unit cell and multi-cell stack of asymmetrical supercapacitors with screen-printed negative electrodes of activated carbon (pigment black) in aqueous electrolytes …

Advances And Challenges Of Intermediate Temperature Solid Oxide Fuel Cells: A Concise Review, Sanping Jiang

Journal of Electrochemistry

Fuel cell is an electrochemical energy conversion device to directly convert the chemical energy of fuels to electricity. Among all types of fuel cells, solid oxide fuel cells (SOFCs) operating at intermediate temperatures of 600~800 ^oC offer an attractive option that is much more fuel flexible than low temperature fuel cells such as proton exchange membrane fuel cells, and is suitable for a wide range of applications. However, two main challenges remain towards the commercial viability and acceptance of the SOFC technologies: the cost and durability. Both are critically dependent on the process, fabrication, performance, chemical and microstructural stability …

Electrocatalytic Activity Of Palladium Nanocatalysts Supported On Carbon Nanoparticles In Formic Acid Oxidation, Jie Huang, Zhiyou Zhou, Yang Song, Xiongwu Kang, Ke Liu, Wancheng Zhou, Shaowei Chen

Journal of Electrochemistry

Palladium nanostructures were deposited onto carbon nanoparticle surface by a chemical reduction method. Transmission electron microscopic studies showed that whereas the resulting metal-carbon (Pd-CNP) nanocomposites exhibited a diameter of 20 to 30 nm, the metal components actually showed a cauliflower-like surface morphology that consisted of numerous smaller Pd nanoparticles (3 to 8 nm). Electrochemical studies showed that the effective surface area of the Pd-CNP nanoparticles was about 40% less than that of Pd black, possibly because the Pd nanoparticles were coated with a layer of carbon nanoparticles; yet, the Pd-CNP nanocomposites exhibited marked enhancement of the electrocatalytic activity in formic …

Adsorption And Electrooxidation Of Carbon Monoxide On Platinum Surfaces Modified With Sulfur, A. Mattox Mathew, W. Henney Matthew, Johnson Adam, Zou Shouzhong

Journal of Electrochemistry

Adsorbed sulfur is commonly considered as a reaction poison. However, small amounts of sulfur on platinum significantly increase the surface reactivity toward carbon monoxide (CO) electrooxidation. For the solution CO oxidation, the onset potential was shifted up to over 300 mV negative to that on S-free surface, and the extent of the negative potential shift increases with the sulfur coverage (X_s) up to about 0.6. The enhanced CO oxidation also depends on the solution pH. For the adsorbed CO, at low sulfur coverages (X_s < 0.3), the oxidation peak potential is about 40 mV negative to that of the corresponding clean Pt. However, at higher coverages, the peak potential is about 30 mV more positive. Surface-enhanced Raman spectra show that the adsorption of sulfur significantly redshifts the Pt-CO stretching frequency. These observations are explained by the weakening of the Pt-CO bond and the hindrance of CO diffusion by Sads.

Kinetic Study Of Photoelectrochemical Oxidation Of Lignin Model Compounds On Tio2 Nanotubes, Min Tian, Daniel Liba, Aicheng Chen

Journal of Electrochemistry

In this study, TiO₂ nanotubes were prepared via the electrochemical oxidation of titanium substrates in a non-aqueous electrolyte and their morphology and microstructures were examined by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The photoelectrochemical oxidation of two lignin model compounds, 1-(3,4-dimethoxyphenoxy)-2-(2-methoxyphenoxy)-1,3-propanediol (DMP) and 3-hydroxy-1-(3,4-dimethoxyphenoxy)-2-(2-methoxyphenoxy)-1,3-propanone (HDM), was investigated. A new band appeared at ~304 nm during the photoelectrochemical oxidation of DMP. The rate of DMP intermediate formation was amplified with the increase of initial concentrations, while it was diminished with increased temperature. Despite the similarity in structure between HDM and DMP, there are only small increases in absorbance …

Ternary Alloy Electrocatalysts For Oxygen Reduction Reaction, Jin Luo, Lefu Yang, Binghui Chen, Chuanjian Zhong

Journal of Electrochemistry

Proton exchange membrane fuel cell represents an important electrochemical energy conversion device with many attractive features in terms of efficiency of energy conversion and minimization of environmental pollution. However, the large overpotential for oxygen reduction reaction at the cathode and the low activity, poor durability and high cost of platinum-based catalysts in the fuel cells constitute a focal point of major barriers to the commercialization of fuel cells. The development of nanostructured catalysts shows promises to addresses some of the challenging problems. The ability to engineer the composition and nanostructure of nanoalloy catalysts is important for developing active, robust and …