Engineering Science and Materials Commons^™

The Equi-Biaxial Fatigue Characteristics Of Epdm Under True (Cauchy) Stress Control Conditions, Mark Johnson, Ray Ekins, Niall Murphy, Stephen Jerrams, John Hanley

Conference Papers

ABSTRACT: Strain amplitude control is most often employed when carrying out fatigue testing of rubber components. Often the design engineer requires fatigue test data that is based on load amplitude control. This is analogous to engineering or nominal stress amplitude control. This usually makes it easy to maintain the load within the specified test limits during extended testing. Values of true stress and strain can be obtained from this approach, but the magnitudes of the maximum true stresses in these tests increase with accumulated cycles, whereas the equivalent maximum engineering stress values remain constant. This is easily demonstrated in the …

Materials Education And Research In Art And Design: A New Role For Libraries (Survey Stats), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Sheet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Booklet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Website), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Collection Creation And Administration: A New Role For Libraries (White Paper), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

The Problem/Opportunity: To define, identify, and guide design-based materials collections in academic settings and foster community among those with existing collections and/or those considering creating and supporting one.

Contents and topics:

1. What is a materials collection?
2. Why have a materials collection?
3. Acquisition strategies
4. Organizational approaches
5. Programming possibilities
6. Symposium summary
7. Resources

Low Velocity Impact Tower Feasibility, Setup, And Impact Testing Of Carbon Fiber Reinforced Epoxy Thermoset And Peek Thermoplastic Matrix Composites, Brent Plehn

Materials Engineering

A low velocity impact tower was donated to Cal Poly's Materials Engineering Department along with four fiber reinforced polymer matrix composites. The tower was set up in building 192 in the Mechanical Testing Laboratory. Improvements were made to the tower including adding velocity detection capabilities, making loose hardware inclusive, adding an extra tower arm for better consistency, adding a double jawed clamp for faster testing, and rerouting the tower's compressed air system to improve performance. A standard operating procedure was drafted, tested, and redrafted for impact testing composite panels. The four composite panels consisted of two quasi-isotropic 16 ply AS-1 …

Fatigue Testing And Data Analysis Of Welded Steel Cruciform Joints, Alina Shrestha

LSU New Orleans Theses and Dissertations

In this study, ABS Publication 115, “Guidance on Fatigue Assessment of Offshore Structures” is briefly reviewed. Emphasis is on the S-N curves based fatigue assessment approach of non-tubular joints, and both size and environment effects are also considered. Further, fatigue tests are performed to study the fatigue strength of load-carrying and non-load-carrying steel cruciform joints that represent typical joint types in marine structures. The experimental results are then compared against ABS fatigue assessment methods, based on nominal stress approach, which demonstrates a need for better fatigue evaluation parameter. A good fatigue parameter by definition should be consistent and should correlate …

Stress Analysis Of Ramberg-Osgood And Hollomon 1-D Axial Rods, Ronald J. Giardina Jr

LSU New Orleans Theses and Dissertations

In this paper we present novel analytic and finite element solutions to 1-D straight rods made of Ramberg-Osgood and Hollomon type materials. These material models are studied because they are a more accurate representation of the material properties of certain metals used often in manufacturing than the simpler composite linear types of stress/strain models. Here, various types of loads are considered and solutions are compared against some linear models. It is shown that the nonlinear models do have manageable solutions, which produce important differences in the results - attributes which suggest that these models should take a more prominent place …

The Effects Of A Collaborative Problem-Based Learning Experience On Students’ Motivation In Engineering Capstone Courses, Brett D. Jones, Cory M. Epler, Parastou Mokri, Lauren H. Bryant, Marie C. Paretti

Interdisciplinary Journal of Problem-Based Learning

We identified and examined how the instructional elements of problem-based learning capstone engineering courses affected students’ motivation to engage in the courses. We employed a two-phase, sequential, explanatory, mixed methods research design. For the quantitative phase, 47 undergraduate students at a large public university completed a questionnaire that measured the components of the MUSIC Model of Academic Motivation (Jones, 2009): empowerment, usefulness, success, situational interest, individual interest, academic caring, and personal caring. For the qualitative phase that followed, 10 students answered questions related to the MUSIC components. We identified several instructional elements that led to motivating opportunities that affected students’ …

College Of Engineering Senior Design Competition Spring 2013, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Senior Design Experience

Part of every UNLV engineering student's academic experience, the Senior Design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs and prototypes a product in this required element of the curriculum. Working in teams, the senior design project encourages students to use everything learned in the engineering and computer design programs to create a practical, real world solution to an engineering challenge.

Beyond the classroom ...

Because of the requirement to work in teams, students also build good communication skills, presentation skills and even business writing skills. They also have to …

Creep, Fatigue And Creep-Fatigue Interactions In Modified 9% Cr - 1% Mo (P91) Steels, Valliappa Kalyanasundaram

Graduate Theses and Dissertations

Grade P91 steel, from the class of advanced high-chrome ferritic steels, is one of the preferred materials for many elevated temperature structural components. Creep-fatigue (C-F) interactions, along with oxidation, can accelerate the kinetics of damage accumulation and consequently reduce such components' life. Hence, reliable C-F test data is required for meticulous consideration of C-F interactions and oxidation, which in turn is vital for sound design practices. It is also imperative to develop analytical constitutive models that can simulate and predict material response under various long-term in-service conditions using experimental data from short-term laboratory experiments. Consequently, the major objectives of the …

A Comparative Study Of Ce3+/Ce4+ Redox Couple On Pt Electrode In Sulfuric Acid And Methanesulfonic Acid, Zhao-Hua Li, You-Qun Chu, Chun-An Ma

Journal of Electrochemistry

The electrochemical oxidations of Ce³⁺ to Ce⁴⁺ on Pt rotating disk electrode (RDE) in both sulfuric acid and methanesulfonic acid (MSA) solutions were studied by using cyclic voltammetry and linear sweep voltammetry. The complexing behaviors of Ce³⁺/Ce⁴⁺ were preliminarily probed and the exchange current density, diffusion coefficient, as well as reaction rate constant were obtained from Butler-Volmer equation. The activation energies of Ce³⁺ oxidation on Pt electrode in two types of acidic media, obtained from Arrhenius equation, were also compared. The results indicate that Ce³⁺ can be oxidized to Ce4+ much easier in …

Electrochemical Activities Of Oxygen-Doped Carbon Surface For V(Iv)/V(V) Redox Couple, Huan Zhang, Lin-Lin Qin, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong, Zhao-Wu Tian

Journal of Electrochemistry

Graphite plate electrodes were treated with oxygen plasma and doped with oxygen as well as oxygen functional groups. With the treatment, the activities of graphite plate electrodes toward VO²⁺/VO₂⁺ redox reactions were improved. FT-IR and EDS analysis results indicated that oxygen functional groups were introduced to the surface of graphite plates after oxygen plasma treatment. In this paper, the graphite plate treated for 20 min showed the highest activity. The average charge efficiency reached 91%, suggesting an increase of 19%, compared with that of the untreated graphite plate under a current density of 8 mA·cm^{-2 …}

Hydrothermal Synthesis Of Pure Li4Ti5O12 And Its Electrochemical Performance, Wen-Jun Xie, Yu-Shi He, Hong Wang, Xiao-Zhen Liao, Zi-Feng Ma

Journal of Electrochemistry

Spinel Li₄Ti₅O₁₂ was prepared by hydrothermal method using commercial anatase (TiO₂) and lithium hydroxide (LiOH) as raw materials. The effects of the LiOH concentration of lithium hydroxide, hydrothermal reaction time and calcination temperature on the structure and electrochemical performance of Li₄Ti₅O₁₂ were investigated. The formation process of Li₄Ti₅O₁₂ was also proposed. The micro-structure and morphology wereas characterized by XRD, SEM, TEM techniques, and the electrochemical performance was analyzed by galvanostatic charge-discharge test. The results show that the pure phase spinel Li₄Ti …

Preparation And Catalytic Properties Of Feco Alloy Nanocatalyst, Ming-Xuan Li, Jie-Lian Ou, Sheng-Pei Chen, Peng Wang, Bin-Bin Xu, Shi-Gang Sun

Journal of Electrochemistry

The FeCo alloy nanoparticles were electrodeposited on glassy carbon electrode by chronoamperometry and were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results showed that the shapes of FeCo nanoparticles were cubes with an average size of 65 nm. The atom ratio of Fe and Co is 1:1. As indicated from the pattern of selected area electron diffraction (SAED), the FeCo cubic nanoparticles were single crystal which belonged to body-centered cubic with an interval of 0.201 nm referring to the (110) facets of FeCo alloy. The FeCo cubic nanoparticles exhibited the enhanced electrocatalytic …

Electrochemical Performance Of Lifepo4/C Synthesized Via Aqueous Solution-Evaporation Route, Ning-Yu Gu, Xing-Hua He, Yang Li

Journal of Electrochemistry

The LiFePO₄/C samples have been synthesized via an aqueous solution-evaporation route with LiH₂PO₄, FeC₂O₄.2H₂O as raw materials and citric acid as a carbon source. X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were used to analyze structure and morphology of the samples. The electrochemical performances of the LiFePO₄/C cathodes were characterized by charge/discharge cures and electrochemical impedance spectroscopy (EIS). The results show that the LiFePO₄/C sample, calcined at 700 °C and contained 3.03% (by mass) carbon, exhibited a highly pure …

Preparation And Methanol Electrooxidation Of Pt/Pmo12/Pedot/Gc Electrodes, Jing-Hua Ma, Rui-Xiang Wang, Yi-Liang Tan, Shan-Shan Wang, Yan-Qin Zhang, You-Jun Fan

Journal of Electrochemistry

Modification of phosphomolybdic acid (PMo₁₂) on poly(3,4-ethylenedioxythiophene) (PEDOT) film (PEDOT/GC) obtained through the electrochemical polymerization was performed using adsorption method (PMo₁₂/PEDOT/GC), followed by electrodepositing Pt on PMo₁₂/PEDOT/GC to prepare Pt/PMo₁₂/PEDOT/GC electrode. Effects of PMo₁₂ and PEDOT on the methanol oxidation performance of electrode were investigated. Results showed that PMo₁₂ obviously changed the morphology and structure of Pt loaded on the electrode, leading to the formation of sharp thorns at the edge of Pt nanostructures. Cyclic voltammetry and chronoamperometry data demonstrated that the catalytic activities of methanol electrooxidation on the Pt/PMo …

Synthesis And Electrochemical Performance Of Si/C Composite Modified By Pani, Guang-Hui Zhang, Pei-Kang Shen, Ge Sang, Ren-Jin Xiong

Journal of Electrochemistry

Silicon/carbon (Si/C) composite materials were prepared through high-energy ball milling and high-temperature solid-phase method, and then coated with thin polyaniline (PAni) film by oxidation. The microstructure and component of the composites were characterized by SEM, XRD, IR, TG, and the electrochemical performance was investigated by cyclic voltammetry (CV) and galvanostatic charge-discharge tests. The results showed that the surface of PAni/Si/G/C composite was coating with complete lamellar structure of PAni film. Its reversible capacity was 784 mAh·g^-1 and 690 mAh·g^-1 could be maintained after 50th charge-discharge cycles.

Synthesis Of Lifepo4/C Cathode By Sol-Gel And Calcining Method With Chitosan Monomer, Jia Xu, Yan-Yan Wang, Rui Wang, Bo Wang, Yue Pan, Dian-Xue Cao, Gui-Ling Wang

Journal of Electrochemistry

The LiFePO₄/C cathode materials for Li-ion battery were synthesized by sol-gel and calcining method using chitosan monomer as a carbon source and a gelating agent. The structures and morphologies were characterized by X-ray diffraction spectroscopy (XRD) and scanning electron microscopy (SEM). The electrochemical performance was investigated by the galvanostatic charge–discharge test. When the molar ratios between chitosan monomer and LiFePO₄ were 1:1.2, the LiFePO₄/C cathode calcined at 600 ^oC showed the best performance. The particle sizes ranged 200 ～ 400 nm. The initial discharge capacity of 155 mAh·g-¹ was achieved at room temperature …

Current Development Of Quantum Dots Based Electrochemiluminescence Immunosensors, Ling-Ling Li, Qian Lu, Jun-Jie Zhu

Journal of Electrochemistry

Electrochemiluminescence exhibits the merits of both luminescence and electrochemistry analysis, and has been extensively employed in biosensors. Quantum dots are considered one of the three main kinds of electrochemiluminescence luminophores due to their unique properties. This paper briefly reviews the classification and signal amplification technology of quantum dots based electrochemiluminescence immunosensors. Future research trends are also suggested.

Properties Of Carbon Coated Tin Negative Electrode For Lithium-Ion Battery, Gui-Chang Liu, Xiao-Xiao Shen, Li-Da Wang

Journal of Electrochemistry

Carbon coated tin power was prepared by decomposing glucose applying a hydrothermal method, and was further used as the active material for negative electrode of lithium secondary battery. Charge-discharge tests show that the carbon coated tin electrode with the addition of 5 wt.% acetylene black as a conductive agent could obtain an initial discharge capacity of 967 mAh·g^-1 and a discharge capacity of 362 mAh·g^-1 after 50 cycles, which is much higher than that of tin electrode (166 mAh·g^-1 after 50 cycles). The coated carbon hinders the agglomeration of tin powder, reduces the irreversible capacity loss of …

Electrochemical Synthesis Of Hierarchical Dendritic Polyaniline Nanostructures, Shao-Huang Weng, Jian-Zhang Zhou, Zhong-Hua Lin, Xin-Hua Lin

Journal of Electrochemistry

In this work, the p-TSA doped and hierarchical dendritic nanostructured polyanilines (PANI) have been prepared by potentiostatic electropolymerization without using any templates at room temperature. The mechanism of the polymerization has been discussed according to the electrodeposition curves. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were employed to confirm the formation of uniform hierarchical dendritic structure on PANI. UV-Vis spectroscopy (UV-Vis) and infrared spectroscopy (FTIR) proved that the prepared PANI is in the form of emeraldine salt. The templateless electrodeposition method is simple, easy to operate, can be applied to fabricate other nanostructures of conducting polymers.

Performance Of Vn As Negative Electrode Materials In Electrochemical Capacitors, Zhao-Hui Gao, Hao Zhang, Gao-Ping Cao, Min-Fang Han, Yu-Sheng Yang

Journal of Electrochemistry

Nanocrystalline vanadium nitride (VN) materials were synthesized by high temperature ammonia (NH₃) reduction of vanadium oxide (V₂O₅). The structure and morphology of VN materials were characterized by XRD, SEM and TEM, while the specific surface area, pore size distribution and supercapacitive behavior by N₂ absorption, cyclic voltammetry (CV) and constant current charge-discharge measurements in 1 mol·L-1 KOH electrolyte. The results showed that the VN sample belonged to the cubic crystal system (Fm3m [225]), and had homogeneous surface and appeared nearly spherical with uniform size. As the reaction time was extended to 12 h, …

Synthesis And Electrocatalysis Of Pdcu Alloy Nanocrystals, Hai-Bin Wu, Rui-Zhong Zhang, Wei Chen

Journal of Electrochemistry

Monodispersed PdCu alloy nanoparticles were synthesized by co-reduction of Cu(acac)2 and Pd(acac)2 with 1, 2-hexadecanediol. The spherical and popcorn-like shapes of PdCu alloy nanoparticles were obtained by changing the ratios of mixed surface protecting ligands of 1-octadecene, and oleylamine or oleic acid. TEM and XRD measurements showed that both PdCu nanoparticles are alloy nanocrystals dominated with (111) planes and the average sizes are 12.7 ± 0.18 and 20.4 ± 0.31 nm for he spherical and popcorn-like PdCu nanoparticles, respectively. The electrocatalytic activities of the PdCu nanocrystals for formic acid oxidation were evaluated by electrochemical cyclic voltammetry (CV). The result showed …

Plastic Deformation Of Astm A36 Steel Using Two-Stage Light Gas Gun, Shawoon Kumar Roy

College of Engineering: Graduate Celebration Programs

To characterize material deformation in high velocity impact. To validate material models for computation simulation purposes.

This ongoing research is an attempt to study the plastic deformation of A36 steel plate (0.5” thick) under hypervelocity impact. Plastic deformation of the target plate was simulated using finite element software LS-DYNA.

Analysis Of Bolted Joints Under Medium And High Impact Loading, Deepak Sankar Somasundaram, Mohamed Trabia, Brendan J. O'Toole

College of Engineering: Graduate Celebration Programs

• Develop test fixture for medium impact study on bolted joints
• Create FEA model that can replicate the experiment
• Develop test fixture for high impact loading
• Create FEA model and select material properties that can produce results that
  closely match experiments.
• Compare different modeling techniques for high impact loading

Sci-Tech Book News Reviews, Susan Fingerman

Sci-Tech News

No abstract provided.

High-Stress Shear-Induced Crystallization In Isotactic Polypropylene And Propylene/Ethylene Random Copolymers, Zhe Ma, Lucia Fernandez-Ballester, Dario Cavallo, Tim Gough, Gerrit W. M. Peters

Department of Mechanical and Materials Engineering: Faculty Publications

Crystallization of an isotactic polypropylene (iPP) homopolymer and two propylene/ethylene random copolymers (RACO), induced by high-stress shear, was studied using in situ synchrotron wide-angle X-ray diffraction (WAXD) at 137 °C. The “depth sectioning” method (Fernandez-Ballester, Journal of Rheology 53:5 (2009), pp. 1229−1254) was applied in order to isolate the contributions of different layers in the stress gradient direction and to relate specific structural evolution to the corresponding local stress. This approach gives quantitative results in terms of the specific length of fibrillar nuclei as a function of the applied stress. As expected, crystallization becomes faster with increasing stress—from the inner …

High Performance Membrane Electrode Assembly With Low Platinum Loadings Prepared By Atomic Layer Deposition For Pemfc Application, Ting Shu, Shi-Jun Liao, Chien-Te Hsieh, Ay Su

Journal of Electrochemistry

A high performance membrane electrode assembly (MEA) with low platinum loadings was successfully prepared with atomic layer deposition (ALD) technique. The anode of the MEA was prepared by depositing platinum on the carbon paper substrate, which was prepared by coating the slurry of carbon black (XC-72R) and Teflon, followed by drying and calcining at 350 °C. The MEAs consisted of the ALD anode or commercial catalyst anode, pretreated Nafion membrane (Nafion-117) and commercial cathode. Performances of MEAs were measured by single cell testing, and the anodes and MEAs were characterized by CV, SEM, TEM and XRD. The results revealed that …