Engineering Science and Materials Commons^™

Lead Modified Nanoporous Platinum Electro-Catalysts For Formic Acid Oxidation, Yuan-Yuan Zhang, Qing-Feng Yi, Ge-Kun-Kun Zuo, Tao Zou, Xiao-Ping Liu, Xiu-Lin Zhou

Journal of Electrochemistry

Platinum (Pt) catalysts modified by other suitable metals significantly enhance their electrochemical activities for formic acid oxidation. In this work, a titanium-supported nanoporous network platinum (nanoPt/Ti) electrode was prepared using a hydrothermal method. The as-prepared nanoPt/Ti electrode was modified with a certain amount of lead by using cyclic voltammetry for different scan cycle numbers (n), namely, n = 10, 15, 20 and 30, to synthesize the novel lead-modified nanoporous Pt (nanoPb_(n)-Pt/Ti) electrodes. Electro-oxidation of formic acid on these electrodes was studied with cyclic voltammetry (CV), chronoamperometry and chronopotentiometry in sulfuric acid solution. CV curves showed that both nanoPt/Ti …

Co3(Hcoo)6@Rgo As A Promising Anode For Lithium Ion Batteries, Heng Jiang, Jing-Min Fan, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

Metal–organic framework(MOF) is a kind of novel electrode materials for lithium ion batteries. Here, a composite material Co₃(HCOO)₆@rGO was synthesized for the first time by in situ loading of Co₃(HCOO)₆ on rGO (reduced oxide graphene) through a solution chemistry method. As an anode material for lithium ion batteries, it exhibited an excellent cycle stability as well as a large reversible capacity of 926 mAh·g^-1 at a current density of 500 mA·g^-1 after 100 cycles within the voltage range of 0.02 ~ 3.0 V vs. Li/Li⁺ with a good rate capability. …

Preparations And Electrochemical Performances Of Carbon Coated Silicon/Graphite Composites, Tian-Yi Gao, Zheng-Liang Gong

Journal of Electrochemistry

In this work, the carbon coated silicon (Si@C) composite materials were synthesized based on the industrial silicon powder (600 meshes) via a high energy ball milling combing with in-situ carbon coating (carbonization) method. The Si@C/graphite (Si/C) composite anode materials were prepared by a simple mechanical ball-milling approach. The effects of carbon coating and the ratio of Si to graphite on electrochemical performances of Si/graphite composite materials were investigated systematically. Compared with the nano-Si/graphite composites, the Si/C composites showed higher reversible capacity, better rate capability and cycle performance. The Si@C materials composited of amorphous carbon and crystal silicon with the primary …

Preparation And Electrochemical Performance Of Ag-Tio2-Mno2 Composites, Ling-Xiao Zhang, Hui-Hui Zhao, Li-Juan Zhang, Yu Fu

Journal of Electrochemistry

The silver-titanium dioxide  co-modified manganese dioxide (Ag-TiO₂-MnO₂) cathode material was prepared through high temperature solid state reaction. The microstructure, phase composition and electrochemical performance of the prepared samples were characterized by X-ray diffraction spectroscopy (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectrometry (FT-IR), X-ray photoelectron spectroscopy (XPS), Energy-dispersive X-ray spectroscopy (EDS), Cyclic voltammetry (CV), galvanostatic discharge and electrochemical impedance spectroscopy (EIS). Results showed that the unmodified and Ag-TiO₂ modified MnO₂ samples both exhibited β-MnO₂ structurebut with different morphologies. The EDS mapping results revealed that Ag was uniformly dispersed on the surface of …

Chemical Stability Investigations Of Catalyst Layer In Pemfc, Yan-Yan Gao, Ming Hou, Yong-Yi Jiang, Dong Liang, Jun Ai, Li-Min Zheng

Journal of Electrochemistry

This work was intended to study the effect of free radicals on the chemical stability of catalyst layer via ex situ accelerated stress test (AST). Fenton reagent was used as the free radical provider in this research. Apart from the decomposition of Nafion in catalyst layer, the agglomerated Pt nanoparticles and the corroded carbon support were also observed after being treated in Fenton reagent for 100 h. Firstly, the existence of fluoride (F) ions evidenced the chemical decomposation of Nafion after being attacked by trace radical species, which was supported by the intensity decrease in the C-F stretching and vibration …

A Study Of Pulse Electrodeposition On Suppressing The Formation Of Lithium Dendrite, Wen-Jun Guo, Zi-Qiong Li, Ruo-Hao Ke, Dong-Fang Niu, Heng Xu, Xin-Sheng Zhang

Journal of Electrochemistry

A pulse charge method was used to suppress the formation of lithium dendrite on the copper electrode in 0.5 mol·L^-1 LiBr/propylene carbonate (PC) electrolyte. The surface variation of lithium deposition was investigated by scanning electron microscope and impedance measurement. The SEM test showed that the lithium dendrites were formed on the copper electrode during the traditional process of electrodeposition. However, the formed dendrite was suppressed by pulse charge method. The results of the impedance measurement confirmed that the pulse electrodeposition could suppress the dendrite under the optimized duty ratio (0.5). The long single pulse deposition time decreased the resistance …

Analysis Of The Low-Cycle Fatigue Behavior Of Silicone Rubber For Biomedical Balloons, Chase Cooper

Materials Engineering

The development of a medical drug delivery device that allows for the deployment drugs into the adventitial tissue of blood vessels requires the inflation of a silicone elastomer. The inflated silicone must be able to consistently endure multiple loading cycles without failing so that the device can operate reliably. There are multiple methods of processing the silicone for the device and the goal of this study is to examine the effect of the various processing methods on the characteristics of the silicone. The Dynamic Mechanical Analysis Machine (DMA) is used to model the conditions of the device’s application by performing …

Direct Synthesis Of Graphene On Niobium And Niobium Nitride, Robin Ekeya, Otto Zietz

Maseeh Summer Undergraduate Research Experience

Since its isolation by mechanical exfoliation in 2004, graphene has attracted enormous interest from the scientific community not the least because of its unique physical and electronic properties. Among these, graphene’s ballistic electron transport and proximity induced superconductivity make graphene-superconductor (GS) hybrid structures a scientifically promising area.

Preliminary Investigation Of Tensile Strength And Impact Characterization Of Cementitious Composite Incorporating Carbon Nanotubes, Robabeh Jazaei

UNLV Theses, Dissertations, Professional Papers, and Capstones

Cement has been largely used in the construction industry, specifically as a matrix for concrete. Recently, a new generation of cement-based composite that greatly increases mechanical properties is replacing conventional concrete. With periodic advances in the field, researchers considered particles with high-aspect ratios such as Carbon Nanotubes (CNTs) to reinforce cement matrices. Although there is not much literature to draw upon in research, some research on improving the tensile strength of cementitious composite incorporating with CNTs does exist. However, there had been no evidence of investigation into impact strength until this study.

Most papers presented examined the effect of multi-walled …

Morphological And Energy Transport Optimization Of Spectrally-Selective Solar Absorber Coatings At Mesoscale, Dale Karas

UNLV Theses, Dissertations, Professional Papers, and Capstones

A special class of cuprous-based inorganic oxide materials, synthesized as nanoparticles via hydrothermal and co-precipitation methods, are portable to spectrally-selective absorber coatings with high solar-thermal energy conversion efficiency. Operating reliably at elevated temperatures when used in tandem with solar concentrators, these materials enable cost-competitive solar energy conversion technology that can be incorporated with thermal energy storage systems, supporting the viability of novel renewable power generation; notably, optimizing absorptive performance while mitigating thermal losses through re-radiated waste heat motivates sustainable energy production particular to desert climates, where water conservation and ecological sensitivity needs are paramount.

This work targets the chemical synthesis …

A Novel Approach To Analyzing Strain Heterogeneity In Polycrystalline Quartz Specimens Deformed At High Pressure And Temperature, Nolan Ambrose Regis

UNLV Theses, Dissertations, Professional Papers, and Capstones

Rheological studies of rocks and minerals allow researchers to study the grain-scale deformation mechanisms that govern large-scale geologic processes from mountain building to mantle mixing. Deforming rock samples with high pressure and temperature apparatuses similar to the Griggs piston cylinder apparatus allows us to simulate deformation at depth. However, many apparatuses are limited to “cook-and-look” analysis and require modeling techniques to determine the evolution of deformation patterns found in experimental samples. A previous study used two-dimensional finite element models to analyze the development of stress and strain patterns in polycrystalline rocks. The study suggested rhythmic patterns in deformed rocks develop …

Numerical Study Of Oxidation In Stainless Steel Alloy Ep-823 By Liquid Lead-Bismuth Eutectic, Rajyalakshmi Palaparty

UNLV Theses, Dissertations, Professional Papers, and Capstones

The oxidation of stainless steel is influenced by the presence of oxygen in the surrounding medium; the oxygen reacts with the alloy to form an oxide. In certain environments, such as nuclear reactor coolant systems, minimal oxidation of the stainless steel containment functions as a protective shield from corrosive coolants such as liquid lead-bismuth eutectic.

In the current study, this minimal oxidation is evaluated for a system in which corrosion-resistant stainless steel alloy EP-823 is subject to an environment of flowing oxygenated liquid lead-bismuth eutectic at a temperature of 743 K, whereby the thickness of the forming oxide layer is …

Ultrasonic Nondestructive Evaluation Of Metal Additive Manufacturing., Venkata Karthik Nadimpalli

Electronic Theses and Dissertations

Metal Additive Manufacturing (AM) is increasingly being used to make functional components. One of the barriers for AM components to become mainstream is the difficulty to certify them. AM components can have widely different properties based on process parameters. Improving an AM processes requires an understanding of process-structure-property correlations, which can be gathered in-situ and post-process through nondestructive and destructive methods. In this study, two metal AM processes were studied, the first is Ultrasonic Additive Manufacturing (UAM) and the second is Laser Powder Bed Fusion (L-PBF). The typical problems with UAM components are inter-layer and inter-track defects. To improve the …

Critical-Point Model Dielectric Function Analysis Of Wo3 Thin Films Deposited By Atomic Layer Deposition Techniques, Ufuk Kılıç, Derek Sekora, Alyssa Mock, Rafał Korlacki, Elena M. Echeverría, Natale J. Ianno, Eva Schubert, Mathias Schubert

Department of Electrical and Computer Engineering: Faculty Publications

WO₃ thin films were grown by atomic layer deposition and spectroscopic ellipsometry data gathered in the photon energy range of 0.72-8.5 eV and from multiple samples was utilized to determine the frequency dependent complex-valued isotropic dielectric function for WO₃. We employ a critical-point model dielectric function analysis and determine a parameterized set of oscillators and compare the observed critical-point contributions with the vertical transition energy distribution found within the band structure of WO₃ calculated by density functional theory. We investigate surface roughness with atomic force microscopy and compare to ellipsometric determined effective roughness layer thickness.

Synthesis And Electrochemical Properties Of Li3V2(Bo3)3/C Anode Materials For Lithium-Ion Batteries, You Wang, Yi-Wen Zeng, Xing Zhong, Xing Liu, Quan Tang

Journal of Electrochemistry

The Li₃V₂(BO₃)₃/C (LVB/C) composite materials were successfully synthesized in two steps:Firstly, a stoichiomertric mixture of Li₂C₂O₄, V₂O₅, H₃BO₃, H₂C₂O₄•H₂O and ethanol was thoroughly ball-milled to get the precursors. Secondly, the precursors were post-calcinated to get the ultimate products. The calcination temperatures of 750 ℃, 800 ℃ and 850 ℃ were selected based on TG-DTA analyses. The crystal structures, surface morphologies and carbon contents of the samples calcinated at five conditions, …

Electrochemical Performance Of Moo2-C Composite Coatings, Quan-Yi Li, Qi Yang, Yan-Hong Zhao

Journal of Electrochemistry

The molybdenum dioxide-carbon(MoO₂-C)composite coatings on the surface of Cu foils were prepared by simple knife coating route and followed by sintering in vacuum. The morphology, composition, structure and electrochemical performance of the MoO₂-C composite coatings were investigated. The results demonstrated that the MoO₂-C composite coatings consist of MoO₂ nano-particles with monoclinic crystal structure and amorphous carbon. Some MoO₂ nano-particles with a size range of 5-30nm were loaded on the surface of carbon matrices; while some MoO₂ nano-particles with a size of ~5nm were encapsulated inside. The composite coatings showed porous structure …

Preparation Of Co3O4/Ti Electrocatalytic Membrane Electrode For Catalytic Oxidation Of Benzyl Alcohol, Yu-Mei Zheng, Zhen Yin, Hong Wang, Jian-Xin Li

Journal of Electrochemistry

The cobalt oxide(Co₃O₄) nanoparticles were loaded on microporous Ti membrane to prepare Co₃O₄/Ti electrocatalytic membrane electrode by dip-coating method. The microstructures and electrochemical properties of Co₃O₄/Ti electrocatalytic membrane were investigated. The Co₃O₄/Ti electrocatalytic membrane reactor (ECMR) assembled by using the Co₃O₄/Ti electrocatalytic membrane as an anode was adopted for catalytic oxidation of benzyl alcohol to produce benzaldehyde and benzoic acid.The effects of different operation parameters on benzyl alcohol conversion, and selectivity to benzaldehyde and benzoic acid of ECMR were studied. …

Electrochemical Oxidation Of P-Chlorophenol On Porous Ti/Bdd Electrode Cooperated With Cathode Dechlorination, Rong-Ling Chen, Wei-Min Huang, Ya-Peng He, Jun Shi, Hai-Bo Lin

Journal of Electrochemistry

The electrochemical oxidation of p-chlorophenol on porous Ti/BDD electrode cooperated with synergistic effect of cathode dechlorination was studied. Electrochemical degradation tests of p-chlorophenol were conducted in single and double compartment electrolytic cells separately, and the results showed that the mineralization happened mainly in the anode region. The product of chloride ions produced from the cathodic reduction of 4-chlorophenol in the single cell migrated to the anode region and further generated active chlorine toward electro-catalytic oxidation. At the same time, the chloride ion produced from the cathode of the double cell was difficult to be migrated to the anode region, which …

Preparations And Corrosion Protection Investigations Of Diethylene Triamine Penta(Methylene Phosphonic Acid)-Zn2+ Conversion Coatings On Cold Rolled Steel Substrates, Wei He, Ru Yan, Ying-Qi Wang, Xiang Gao, Hou-Yi Ma

Journal of Electrochemistry

Novel diethylene triamine penta(methylene phosphonic acid) (DTPMPA)-zinc ion (Zn²⁺) conversion coatings with uniform blue color and excellent corrosion protection were directly formed on the cold rolled steel (CRS) substrates by immersing a CRS plate into the film-forming solutions containing the appropriate concentrations of DTPMPA and Zn²⁺ ion at the proper pH. In this paper, surface morphologies and elemental compositions of DTPMPA-Zn²⁺ conversion coatings were characterized by SEM and EDS, respectivey. The surface functional groups, chemical constituents and binding modes to the substrates were investigated by means of FTIR and XPS methods. The influences of DTPMPA concentrations …

Simulation Analysis In Dynamic Performance Of Proton Exchange Membrane Fuel Cell Under Starting Condition, Yan Xiao, Ying-Jie Chang, Wei Zhang, Qiu-Hong Jia

Journal of Electrochemistry

Based on the equivalent circuit model, by considering both the dynamic gas pressure model and the dynamic heat transfer model, a lumped parameter model is developed. The start process of the fuel cell is simulated by using SIMULINK software. The undershoot of the voltage is observed from the simulation results, and the response time of the voltage is basically the same as that of the fuel cell temperature, which indicates that the temperature has great influence on the dynamic performance of the fuel cell. From the perspective of the temperature, the dynamic responses of the thermodynamic potential, the activation overvoltage, …

Interaction Between Energy And Electrocatalysis —— A Review On The 1st Young Scientist Forum On Energy Electrocatalysis, Hong Li, Wen-Bin Cai

Journal of Electrochemistry

No abstract provided.

Effects Of Rotating Magnetic Fields On Pem Fuel Cell Performance, Mao-Liang Wu, En-Ze Wang, Guang-De Pan, Zhong-Jun Liu, Fei Xie

Journal of Electrochemistry

Proton Exchange Membrane (PEM) fuel cell performance may be improved by application of additional magnetic fields. In this work, one square permanent magnet, made of either 16 combination cylinder magnets with homopolarity or 16 combination cylinder magnets with heteropolarity, was exerted on the fuel cell surface to produce additional magnetic field affecting PEM fuel cell performance. The influences of magnetic field status (rotating, static and none) on polarization and power density curves measured in a PEM fuel cell were investigated. The results verified the benefit of magnetic field, proving that the magnetic field distribution could improve the fuel cell output. …

Preparation Of Ni(Dpim)2Cl2 Complex For The Electrocatalytic Reduction Of Co2, Li-Pu Zhang, Dong-Fang Niu, Xin-Sheng Zhang

Journal of Electrochemistry

A new Ni(dpim)₂Cl₂complex using 2-(diphenylphosphino)-1-methylimidazole (dpim) as ligand was prepared and served as a catalyst for the electrochemical reduction of CO₂. The electrochemical redox behavior of Ni(dpim)₂Cl₂ in CH₃CN/TPABF₄ solution under nitrogen atmosphere showed the two-electron irreversible reduction at -0.7 V and one-electron quasi-reversible reduction at -1.3 V. After bubbling CO₂ into the electrolyte, the reduction peak appeared at -1.3 V became irreversible and the peak current increased from 0.48 mA·cm^-2 to 0.55 mA·cm^-2. Moreover, the peak current at -1.3 V could further increase …

Preparation And Properties Of Manganese Oxide And Polyaniline-Carbon Composite Electrode, Tian-Tian Zhou, Bing Wu, Chao Deng, Ying Gao

Journal of Electrochemistry

The polyaniline-carbon (PAnC) electrode was prepared by the polymerization of aniline monomer and activated carbon in ice water bath, and followed by chemical deposition of manganese dioxide MnO₂-PAnC composite material. The specific capacitance of MnO₂-PAnC reached 459 F•g^-1. The cyclic voltammetric results showed a small deformation in the voltammogram curve obtained with the MnO₂-PAnC electrode at high scan rate, indicating good reversibility and capacitive properties. The AC impedance results revealed that the MnO₂-PAnC electrode displayed the smallest charge transfer resistance and the fastest diffusion
rate of surface ions than other …

Review Of Challenges And Advances In Modification Of Food Package Headspace Gases, Ziynet Boz, Bruce A. Welt, Jeffrey K. Brecht, William Pelletier, Eric Mclamore, Gregory A. Kiker, Jason E. Butler

Journal of Applied Packaging Research

Modified Atmosphere Packaging (MAP) has been widely used as an effective way to preserve foods. Fresh produce, meat and meat products, seafood, and dairy products can benefit from modified gaseous atmospheres, which are usually achieved by reducing oxygen and increasing carbon dioxide concentrations, within limits, defined by product tolerances. MAP of fresh produce is particularly challenging because products are living and respiring. Respiration rates depend on several factors including temperature, oxygen, and carbon dioxide concentrations. Balancing package permeation with respiration is challenging, often due to limited selection of practical packaging materials. Failing to remain within tolerance limits of products leads …

An Evaluation Of Induction Heating In Healthcare Food Industry, Barrett Alexander Hampton

Masters Theses & Specialist Projects

This thesis addresses the problem healthcare facilities are having in maintaining proper food temperatures while transporting meals to patients after food has left the kitchen area. Induction heat has been a known method for generating heat for many years. The commercial food industry currently uses this technology, which is beginning to appear in the residential sector as well because of developments made by manufacturers. This study focuses on the top commercial brand models of induction heaters and the supporting materials currently used to create heat sources to maintain food temperatures in hospitals and long term care facilities.

The research in …

Creep Of Hafnium Diboride -20 Vol% Silicon Carbide At 1500°C In Air, Glen E. Pry

Theses and Dissertations

Refractory metal borides, commonly referred to as Ultra High Temperature Ceramics (UHTCs), exhibit a number of unique properties, such as extremely high melting temperature and hardness, chemical stability, high electrical and thermal conductivity and corrosion resistance. It has been demonstrated that the addition of SiC improves the oxidation resistance of ZrB2- and HfB2-based UHTCs above 1200°C by modifying the composition of the oxide scale. Addition of SiC retards the oxidation rate of ZrB2 and HfB2 by forming a protective layer of borosilicate glass. Creep deformation is one of the critical criterion for structural application of ceramics at elevated temperatures. Compression …

Tensile Properties And Fatigue Behavior Of Geopolymer Matrix Composites With Carbon Fiber Reinforcement At Elevated Temperature, Steffan M.L. Wilcox

Theses and Dissertations

The tensile stress-strain and tension-tension fatigue of geopolymer matrix composites reinforced with 0/90 carbon fibers was investigated at 23 and 300°C in laboratory air. Geopolymers are inorganic polymeric materials composed of alumina, silica, and alkali metal oxides. Because geopolymers are synthesized as a fluid mixture or particles and liquid, they can be cast into a desired shape, and cured at only slightly elevated temperatures. The relative ease of synthesis and low processing temperatures make geopolymers an attractive choice as a matrix material for composite materials. Geopolymers also offer resistance to heat and oxidizing environments. Currently, geopolymer matrix composites are being …

Preparation And Characterization Of Titanate-Phosphate Passivation Film On Tinplate, Zi-Yu Wang, Ming-Hao Wang, De-Yu Li, Ning Li

Journal of Electrochemistry

A passivation film was prepared on tinplate surface with a composite passivating agent made of titanate and phosphate. The surface morphologies, chemical compositions and corrosion resistances of the passivation films were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), salt spray test, Tafel polarization measurement and electrochemical impedance spectroscopy (EIS). The results were compared with those films untreated and treated with titanate or phosphate passivation. It was shown that the titanate and phosphate passivation film was mainly composed of Ti₃(PO₄)₄·nH₂O and TiO₂. The finely crystallized surface could seal …

Preparation And Properties Of Nanocrystalline Nickel By Pulse Electrodeposition On Glassy Carbon, Ya-Li Zhang, Ming-Xian Zhang, Teng-Da Guo, Yan-Jie Zhao, Sheng-Xue Yu

Journal of Electrochemistry

Nanocrystalline nickel exhibits electrocatalytic activity for methanol. In this work, nanocrystalline nickel coating has been obtained by using the double pulse method on glassy carbon materials surface. The influence of pulse conditions on the grain size of nanocrystalline nicke was studied. The concentrations and compositions of the plating bath were  300 g·L^-1 NiSO₄·6H₂O,45 g·L^-1 NiCl₂·6H₂O,40 g·L^-1 H₃BO₃,5 g·L^-1 C₇H₅NO₃S,and 0.05 g·L^-1 C₁₂H₂₅NaO₄S. The optimal pulse process parameters including the average pulse …