Engineering Science and Materials Commons^™

Low-Temperature Performance Of Li-Ion Battery With Fluoroethylene Carbonate Electrolyte, Chun-Wei Yang, Feng Wu, Bo-Rong Wu, Yong-Huan Ren, Jing-Wen Yao

Journal of Electrochemistry

The low temperature performance of electrolytes containing FEC including FEC+EMC, EC and PC, as well as the compatibility of electrolytes with LiFePO₄ anode and with MCMB cathode were investigated.The electrolyte exhibits a high value of ionic conductivity at low temperature.The stability of cathode was enhanced by the formation of SEI film at 1.6 V as a result of FEC reaction. The infrared spectra showed that FEC can suppress decomposition of other solvents during SEI formation, and lower the resistance of SEI on MCMB cathode. The electrochemistry test indicates that Li-ion batteries with FEC electrolyte display high capacity at low …

Synthesis Of Mesoporous Nickel Oxide For Supercapacitor Application, Xuan-Xuan Chen, Zhen-Zhen Zhao, Deng-Chao Wang, Zhong-Jie Huang, Wen-Bin Ni, Li Yu, Jian-Wei Zhao

Journal of Electrochemistry

Mesoporous nickel oxide has been synthesized by calcining metal-organic coordination precursor.Transmission electron microscopy and BET test showed that the prepared NiO had a regular morphology and displayed a narrow size distribution.Electrochemical tests revealed that such mesoporous NiO had a specific capacity of 72 F·g^-1 at the current of 2.0 A·g^-1.Futhermore,the material showed excellent cycle-life stability.There was no degradation of capacitance after 1000 cycles.

A Titanium-Supported Nanoporous Pd Electrocatalyst For Methanol Oxidation, Feng-Juan Niu, Qing-Feng Yi

Journal of Electrochemistry

Titanium-supported nanoporous palladium electrode(nanoPd /Ti) was prepared by a hydrothermal process in the presence of the ligand EDTA and using formaldehyde as reducing agent.SEM images showed that the size of Pd particles was about 60 nm and the Pd particles were connected with each other to form a three-dimensional network structure.Cyclic voltammetry(CV) and electrochemical impedance spectroscopy(EIS) were applied to evaluate the electrocatalytic activity of the nanoPd/Ti electrode towards methanol oxidation in alkaline solution.CV results showed that the nanoPd /Ti electrode presented high anodic peak densities and a low onset potential for methanol oxidation.Also nanoPd /Ti electrode showed excellent CO tolerance …

Electrocatalytic Oxidation Of Hydrazine At Rutin Carbon Nanotubes Modified Electrode, Hong-Fang Zhang, Qing-Lin Sheng, Jian-Bin Zheng

Journal of Electrochemistry

The electrochemical behavior and electrocatalytic oxidation of hydrazine on rutin multiwall carbon nanotubes modified glassy carbon electrode were studied by cyclic voltammetry.The experimental results indicated that the electrode exhibits good electrocatalytic activity to hydrazine at a reduced oxidation potential of 262 mV.The amperometric response of the modified electrode showed linear increase after successive addition of hydrazine in the concentration range of 2.5×10^-6~1.0×10^-4 mol·L-1 with a detection limit of 5×10^-7 mol·L^-1.

Applications Of Raman Spectroscopy Technique In Lithium Ion Batteries, Liang Zhao, Yong-Sheng Hu, Hong Li, Zhao-Xiang Wang, Hong-Xing Xu, Xue-Jie Huang, Li-Quan Chen

Journal of Electrochemistry

The Raman spectroscopy has been widely used in the study of lithium ion batteries.In this short review,we gave some examples of the applications of Raman spectroscopy in the study of electrode materials including carbonaceous materials,spinel LiM_xMn_2-x O₄,LiFePO₄,as well as polymer electrolytes,room temperaturemolten salt electrolytes and the solid-electrolyte interphase layers.The advantages and disadvantages of the ex-situ and in-situ Raman spectrum techniques are discussed.Using new Raman techniques to investigate Li-ion batteries are suggested.

Novel Anion Exchange Membranes Base On Copolymer Of 2-(Diethylamino) Ethyl Methacrylate And Fluoro-Polyacrylate For Alkaline Direct Methanol Fuel Cells, Yan-Mei Zhang, Jun Fang, Ge Yan, Yong-Ze Zhuang

Journal of Electrochemistry

Anion exchange membrane fuel cells,which use anion exchange membranes as polyelectrolytes,have attracted more and more research interests recently.In this work,a series of hydroxyl-conducting anion-exchange membranes based on the copolymer of 2-(Diethylamino)ethyl methacrylate and fluoro-polyacrylate were prepared by radical polymerization,and their potential applications in alkaline fuel cells were assessed.It was shown that the ionic conductivity of the membranes reached 10^-2 S·cm^-1 at room temperature,while the methanol permeability was lower than 10^-7 cm²·s^-1.The maximum power density of fuel cell assembled with this membrane was achieved to be 43.2 mW·cm^-2 at room temperature,indicating possible application …

Electrooxidation Of Methanol On Multilayer Films Of Polypyrrole-Platinum Electrode, Ling Zhang, Long-Zhen Zheng

Journal of Electrochemistry

Multilayer films of polypyrrole-platinum electrode were fabricated by cyclic voltammetric technique.Electro-oxidation of methanol on this electrode was investigated with the aid of cyclic voltammetry and chronoamperometry.Results demonstrated that the multilayer of polypyrrole-platinum electrode behaved better electrocatalytic performance for electro-oxidaton of methanol and better poison resistant.Furthermore,with the increase of deposited platinum loadings,the rate controlling step on electro-oxidation reaction of methanol was changed from CO oxidation to sorption-desorption of hydrogen.

Electrochemical Deposition Of Zinc Oxide Crystal Whiskers, Peng-Zeng Lu, Su Li, Jin-Qian Jia, Zhen-Hai Liang

Journal of Electrochemistry

Pine needle ZnO crystal whiskers were electrodeposited by anodization of zinc foil.The crystal whiskers were characterized by scanning electron microscopy(SEM) and X-ray diffraction(XRD) spectroscopy.The results show that the lengths and diameters of ZnO crystal whiskers are 200~300 nm and 20~50 nm,respectively,with the ratio of the length to diameter ranging from 10~15.The whiskers belong to wurtzite ZnO(JCPDS 36-1451) with good crystallinity and high purity.The crystalization behavior of ZnO was studied by cyclic voltammetry.The effects of the surface oxide layer at the zinc substrates and the [Zn(OH)₄]^2-concentration of the aqueous electrolyte on the formation of zinc oxide whiskers …

Preparation And Characterization Of Iron Oxide And Hydroxide Based Nanomaterials, Guillermo Carbajal Franco

Open Access Theses & Dissertations

Iron (Fe) oxides and hydroxides are common and abundant materials. They exhibit diverse crystal structures, properties and phenomena by virtue of which they find a wide range of scientific and technological applications. Controlled growth and manipulation of the specific structure and electronic behavior to meet the requirements of a given application is a challenging problem in view of many possible phases and composition of the resulting materials. The preparation method and experimental conditions will, therefore, significantly affect the properties and performance of Fe oxides and hydroxides. The goal of the project is to obtain Fe-based oxide/hydroxide catalytic materials and to …

Variable Block Size Motion Compensation In The Redundant Wavelet Domain, Ahmed Abdelgadir Suliman

Dissertations

Video is one of the most powerful forms of multimedia because of the extensive information it delivers. Video sequences are highly correlated both temporally and spatially, a fact which makes the compression of video possible. Modern video systems employ motion estimation and motion compensation (ME/MC) to de-correlate a video sequence temporally. ME/MC forms a prediction of the current frame using the frames which have been already encoded. Consequently, one needs to transmit the corresponding residual image instead of the original frame, as well as a set of motion vectors which describe the scene motion as observed at the encoder. The …

Fabrication And Characterization Of Nanocrystalline Yttrium Oxide Thin Films For Electronic Device Applications, Mudavakkat Vikas Haridas

Open Access Theses & Dissertations

This thesis presents the optimization of growth conditions for fabricating nanocrystalline Yttrium Oxide (Y2O3) thin films on silicon and optical grade, high quality quartz substrates in order to study its structural, optical and electrical properties for electronic device applications.

Commercially Y2O3 has proven to be difficult to fabricate at high quality due to its high temperature growth requirements and the need to alter established fabrication methods for electronic devices. A high temperature requirement for high quality poses a problem for research and analysis. This calls upon for an optimization of the growth conditions to facilitate fabrication of thin films for …

The Sol-Gel Synthesis And Electrochemical Performance Of Li3V2(Po4)3/C Cathode Material For Lithium Ion Battery, Li-Ying Liu, Lian Chen, Hai-Yan Zhang, Yu-Chun Zhai

Journal of Electrochemistry

Li₃V₂(PO₄)₃/C was synthesized by sol-gel method with citric acid as chelate and C sources. Physical and electrochemical performances of as-prepared materials were characterized through XRD, SEM and galvanostatic charge-discharge tests,etc. The results showed that products produced by calcining at 800 ℃ for 12 h had a single phase crystal structure and relatively small particle sizes with uniform distribution. At 0.1 C, 0.5 C and 1 C, the initial specific discharge capacities were 153.0, 143.1 and 130.6 mAh·g^-1, respectively, and capacity efficiencies were 93.1%, 85.4% and 77.3% after 50 cycles, respectively. …

Photoelectrochemical Properties Of N, S, And Cl Modified Nano Tio2 Thin Films, Hong Yun, Chang-Jian Lin, Jing Li, Rong-Gui Du

Journal of Electrochemistry

The nitrogen(N),sulfur(S) and chlorine(Cl) modified nano TiO₂ thin films were prepared by adding Ti(O-n-Bu)₄ as the precursor into concentrated HNO₃,H₂SO₄ and HCl Solutions,respectively,on different substrates in a sol-gel process.The photoelectrochemical performances of N,S and Cl modified nano TiO₂ thin films have been studied by UV-vis(DRS),photocurrent curves,EIS and OCP-time curves.N-modified TiO₂ nano films show better surface structure,which helps to improve the quantum efficiency of nano TiO₂ thin films.

Hydrothermal Reduction Synthesis Of Lifepo4 And Its Electrochemical Performance, Hong-Li Zou, Guang-Hui Zhang, Pei-Kang Shen

Journal of Electrochemistry

The cathode materials of LiFePO₄ were prepared via a hydrothermal reduction method using FeCl₃ as Fe source and iron as a reducing agent.The results showed that ferric salt could be reduced to ferrous salt completely under the hydrothermal condition and pure-phase LiFePO₄ was obtained based on the test results of XRD and FTIR.Carbon-coated LiFePO₄ was synthesized by pyrolysisng glucose at high temperature.The morphologies of pure LiFePO₄ displayed cluster-like while the LiFePO₄/C displayed sphere-like particles.The electrochemical test showed that the LiFePO₄/C had good rate performance,while LiFePO₄ delivered much lower discharge capacity.

Effects Of Solvents And Electrolyte Salts On The Electrochemical Reduction Of Oxygen In Non-Aqueous Electrolytes, Yan-Yan Tian, Wei Wu, Jun Gao, Yong Yang

Journal of Electrochemistry

The electrochemical reduction processes of oxygen in different non-aqueous solvents such as acetonitrile(MeCN),propylene carbonate(PC) and their mixtures were investigated by cyclic voltammetry method.The results indicated a one electron reduction of oxygen to O^2-occured in these systems as a first step reduction,no matter whether in tetrabutylammonium hexafluorophosphate(TBAPF₆)/MeCN or TBAPF₆/PC electrolyte.However,the CV curves in 0.1 mol·L^-1 TBAPF₆/MeCN showed a couple of reversible redox peaks,indicating that the reduction process of oxygen was irreversible in the 0.1 mol·L^-1 TBAPF₆/PC electrolyte.In the PC-based electrolyte,the reduction current peak reduced largely and the oxidation peak …

Electrodeposition Of Lead Dioxide From Dluoroborate Solutions, Chun-Mei Kong, Yong-Ming Tang, Wen-Zhong Yang, Xiao-Yuan Yang

Journal of Electrochemistry

The PbO₂ anodes were prepared on platinum from fluoroborate media and its doped solutions by electrodeposition technique.Elecchemical and pysicochemical properties of these PbO₂ films were studied by cyclic voltammetry methods,XRD and SEM.The results showed that the presence of BF₄-increased PbO₂ electrodeposition rate;the prepared lead dioxide consisted of β-PbO₂;the preferential orientation of crystals and surface morphology were affected a lot by doping F-and Fe³⁺.The FB/F-Fe-PbO₂ electrode exhibited regular-shaped layers with compact morphology.Furthermore,increasing current density also change the preferential orientation of PbO₂ crystals.

Research On Nafion/Sio2 Composite Membrane In All Vanadium Redox Flow Battery, Dong-Dong Liu, Mao-Cai Lin, Tao Guan, Qing-Chun Yu

Journal of Electrochemistry

The Nafion117/SiO₂ composite membrane was prepared by sol-gel method.The results showed that,during composite membrane preparation process,the ratio of MeOH and TEOS did not affect the penetration rate of VO²⁺ basically,however,the lowest permeability of 427×10-9cm²/s in the membrane was achieved while hydrolysis time was 10 min and natural drying for 24 h after hydrolysis,which reduced by 52 times than that in Nafion117 membrane.The SEM tests proved that SiO₂ grains grew bigger in the composite membrane during the natural drying,and most of the holes in Nafion117 were filled.Single cell test showed the battery power efficiency was improved …

An In Situ Fourier Transform Infrared Spectroelectrochemical Study On Alcohols Electrocatalytic Oxidation At Pd Electrode In Acidic Solution, Hai-Ping Huang, Lian-Qin Wang, Pei-Kang Shen

Journal of Electrochemistry

The methanol and ethylene glycol electrooxidation on palladium electrode in acidic solution has been investigated by cyclic voltammetry and in situ Fourier transform infrared spectroelectrochemistry. It shows that the oxidation of methanol and ethylene glycol at Pd electrode cannot proceed until over 1.5 V in acidic and neutral media. The overpotential decreases and the peak current density increases with the reduction in pH values. The formation of the oxygen-containing species significantly affects the alcohol oxidation on Pd electrode. The in situ FTIR spectroscopic measurements show that the oxidation products of ethylene glycol on Pd electrode are CO₂ and oxalic …

Electrooxidation Of Carbon Monoxide On Pd Thin Film-Coated Au Electrodes: Film Thickness Dependence, Yuqing Yang, Shouzhong Zou

Journal of Electrochemistry

The adsorption and electrooxidation of CO on Pd-coated Au electrodes were studied by cyclic voltammetry and surface-enhanced Raman spectroscopy (SERS) . It is found that CO oxidation activity is film thickness dependent. Cyclic voltammograms (CVs) showed that CO oxidation peak potential shifted positively with the increase of the Pd thickness. SERS showed a redshift of the C—O stretching frequency with increasing Pd film thickness. These observations were explained by the dband theory. The strain effect strengthens CO adsorption and stabilizes adsorbed CO,while the ligand effect weakens CO adsorption and eases its oxidation. The ligand effect overpowers the strain effect.

In Situ Surface-Enhanced Raman Scattering Spectroscopic Study Of Sulfur Adsorption On Polycrystalline Platinum Electrode Surface, Bolian Xu, In-Su Park, Ying Li, De-Jun Chen, Yuye J. Tong

Journal of Electrochemistry

The paper reports the first in situ surface enhanced Raman scattering (SERS) spectroelectrochemistry study of sulfur adsorption and electro-oxidation on highly roughened polycrystalline Pt surface in both acidic and basic supporting electrolytes. The SERS spectra were taken at a constant electrode potential after accumulative electro-oxidation CVs of the Pt electrode with pre-adsorbed sulfur species and at different electrode potentials that were varied stepwise of the Pt electrode immersed in sulfur-containing electrolytes without pre-adsorbed sulfur species. In both cases,a dominant vibrational band at 299 cm^-1 in acidic electrolyte but at 310 cm^-1 in basic electrolyte was observed,which was assigned …

Solid State Nmr Studies Of Lithium Manganese Silicate As Positive Electrode Materials For Li-Ion Batteries, Hu Cheng, Zi-Geng Liu, Yi-Xiao Li, Zhong Chen, Yong Yang

Journal of Electrochemistry

The Li₂MnSiO₄ cathode material for lithium ion batteries was synthesized by sol-gel assisted hydrothermal method. XRD,FTIR and SS-NMR were used to study the phase,structure and morphology of obtained samples. Electrochemical performance of cathode material was tested. The results show that the main phase of sample prepared was Li₂MnSiO₄,whereas a small amount of impurities (Li₂CO₃) were existed. The Li₂MnSiO₄ cathode material gave an initial discharging capacity of about 190 mAh·g ^-1. But this capacity faded rapidly during the cycling process due to the decomposition of Li …

Comparative Study Of Nanoporous Pt, Ptru And Ptruir Catalysts Using Electrochemical Ftir Spectroscopy, M. Amussen Robert, Holt-Hindle Peter, Nigro Samantha, Aicheng Chen

Journal of Electrochemistry

In recent years much effort has been put towards developing efficient Pt-based electrocatalysts for applications in fuel cells. With the rising cost of precious metals such as Pt,the need to enhance the activity and to decrease the load of catalysts is prominent. Herein we report on the synthesis and comparative study of nanoporous Pt,PtRu and PtRuIr electrocatalysts. The nanoporous electrodes were fabricated using a hydrothermal method and characterized by scanning electron microscopy (SEM) ,energy dispersive spectroscopy (EDS) ,X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) . The electrocatalytic activity of the fabricated nanopo- rous materials was evaluated using both CO …

Studies Of Oxidation Processes Of Adsorbed And Solution Co On Pt(110) Electrode By Cyclic Voltammetry And In Situ Ftirs, Li Tian, Jun-Tao Li, Jin-Yu Ye, Chun-Hua Zhen, Shi-Gang Sun

Journal of Electrochemistry

The oxidation processes of adsorbed CO (COad) and solution phase CO (COsol) on Pt(110) electrode were investigated by cyclic voltammetry and in-situ FTIR spectroscopy. It has revealed that in comparison with COad on Pt(110) in a CO-free solution,the oxidation current peak of COsol in a CO-saturated solution is positively shifted ca. 168 mV,and the peak current density has been increased by 6. 70 times. Linear adsorbed CO (COL) is determined by in-situ FTIR spectroscopy as the main species,which is uniformly distributed on Pt (110) surface. In a CO-free solution,the onset potential of COL is measured by in-situ FTIRS ca. 0. …

Simulation Of Temperature Distributions In Tissue Upon Laser Pulse Irradiation Including Water Mass Transfer, Deepthi Nagulapally

Electrical & Computer Engineering Theses & Dissertations

Lasers, due to their unique characteristics, have tremendous applications in the medical field. Generally all laser applications in hie-medicine involve the propagation of laser energy through tissue. Energy is deposited giving rise to many physical, hie-chemical, and mechanical effects. Among these are dynamical changes in the local temperature distributions within the tissue. Analysis of the temperature changes requires the creation of an appropriate optical transmission and heat flow model that incorporates user specified laser parameters. Here, a numerical simulation model was developed to study both steady state and time dependent temperature distributions due to pulsed laser radiation within user specified …

Research On Electrochemical Performance Of Lithium-Ion Battery Cathode Material Lini(1/3)Co(1/3)Mn(1/3)O2 In Aqueous Lino3 Solution, Jun Zheng, Xin Jia, Chong Wang, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

The cathode material of LiNi_1/3Co_1/3Mn_1/3O₂ synthesized by sol-gel method shows excellent high rate performance, and high output power density during discharge process. A well-ordered layered α-NaFeO₂ structure was confirmed by XRD and a primary particle size of about 500 nm was indicated by SEM. Galvanostatic charge-discharge test indicates that LiNi_1/3Co_1/3Mn_1/3O₂ in 2 mol·L^-1 LiNO₃ aqueous solution with pH 12 reached a ca-pacity of 147 mAh/g while charged and discharged at 2C. The capacities were 64, 33, 16 mAh/g with 80C (14.4 A/g), 150C …

Fabrication Of Electrochemically Activated Glassy Carbon/Bismuth Film Electrodes For Sensitive Analysis Of Pb(2+) And Cd(2+), Kang Shi, Wen-Jing Wang, Kun Hu

Journal of Electrochemistry

The application of electrochemically activated glassy carbon (GC) in the in-situ preparing of bismuth film electrodes (BiFEs) to analyze Pb^{2 +} and Cd^{2 +} was investigated. The glassy carbon electrodes were electrochemically activated by either potentiostic or cyclic polarization in 1 mol·L^-1 NaOH solution. Experimental results show that employment of HCl solution as the analytical solution not only can reproducibly renew the electrochemically activated GC electrode surface with an electrochemical clear procedure, but also can greatly enhance the sensitivity of BiFes method for analysis of Pb^{2 +} and Cd^{2 +}. The test range thus …

Failure Reaction Mechanism Of Internal Short-Circuit For Lithium-Ion Batteries, He Li, Shen-Jun Yu, Zhi-Kui Chen, Guang-Chuan Liang

Journal of Electrochemistry

In this work, the battery impact testing machine has been used to study the failure progress of internal short-circuit (ISC) for lithium ion batteries. The reaction mechanisms between cathode/anode and electrolyte in the battery at different temperatures were characterized by differential scanning calorimetry (DSC), gas chromatography/mass spectrometry (GC/MS) and X-ray diffraction (XRD). The experimental results show that the ISC failure of the battery was mainly due to the reaction between cathode Li_0.5CoO₂ and electrolyte. The decomposition and oxygen evolution reactions of cathode occurred when the temperature reached a certain value. At the same time a fierce oxidation …

Synthesis And Electrochemical Properties Of Li3V2(Po4)3/C Cathode Materials For Lithium Ion Battery, Li-Ying Liu, Hai-Yan Zhang, Lian Chen, Yu-Chun Zhai

Journal of Electrochemistry

Cathode material Li₃V₂(PO₄) ₃ /C for Lithium-ion battery was synthesized by combination of ball milling and baking. Physical and electrochemical performances of as-prepared materials were characterized through XRD,EIS and galvanostatic cell cycling. The results show that the products were monoclinic Li₃ V₂ (PO₄) ₃ with well-developed crystal structure. At 0. 1C,0. 25C and 0. 5C,the initial discharge capacities were 150. 6,134. 1 and 107. 1 mAh·g^-1 ,respectively. Capacity retention rates were 87. 3% after 130 cycles at 0. 25C and 87. 2% after 105 cycles at 0. 5C. Charge-discharge …

Optimization Of Membrane Electrode Assembly In Air-Breathing Direct Methanol Fuel Cell, Liang Ma, Wei-Wei Cai, Jing Zhang, Liang Liang, Jian-Hui Liao, Chang-Peng Liu, Wei Xing

Journal of Electrochemistry

The structure and performance of MEA were optimized by tailoring the catalyst layer,cathodic microporous layer (MPL) ,anodic MPL and membrane,with the considerations of unique characteristics of airbreathing direct methanol fuel cell (DMFC) such as methanol crossover and cathode flooding. It was found that high catalyst loading could suppress the methanol crossover effectively,but too high catalyst loading can lead to high mass transport resistance. Hydrophobic anodic MPL with 30% (by mass) PTFE could facilitate the CO₂ bubble detachment,which decreased the methanol concentration gradient and suppressed the methanol crossover accordingly. When Nafion 115 was used as membrane,methanol crossover was severe,while Nafion …

A High Performance Sulfur/Carbon Xerogel Composite In Lithium Sulfur Battery Application, Chong Wang, Jia-Jia Chen, Qiu-Jie She, Qian Zhang, Yi-Ning Shi, Ming-Sen Zheng, Quan-Feng Dong

Journal of Electrochemistry

Sulfur/carbon composite was synthesized by the thermal method with the carbon xerogel as the conductive framework. The property of composite was characterd by XRD and SEM. It shown that the composite with the particle size below 10 μm had the same morphology as the carbon xerogel and the sulfur was absorbed in the pores in non-crystalline. The discharge capacity of the composites were 1311 mAh/g and 1107. 1 mAh/g at 0. 1C and 0. 2 C rates,respetively. And a retention capacity was about 800 mAh/g after 30 cylcyes.